scsi: qla2xxx: Fix NVMe session down detection

When Target port transitions personality from one to another (NVMe <-->
FCP), there could be some overlap of the two where one layer is going down
while the other layer is coming up. This overlap can cause temporary I/O
error. Detect those errors/transitions and recover from them. Triggers
session tear down and allow relogin to re-drive the connection under the
following conditions:

 - NVMe command error

 - On PRLO + N2N (rida format 2)

Link: https://lore.kernel.org/r/20210817051315.2477-11-njavali@marvell.comSigned-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

drivers/scsi/qla2xxx/qla_attr.c

@@ -2733,12 +2733,14 @@ qla2x00_terminate_rport_io(struct fc_rport *rport)
 	 * final cleanup of firmware resources (PCBs and XCBs).
 	 */
 	if (fcport->loop_id != FC_NO_LOOP_ID) {
-		if (IS_FWI2_CAPABLE(fcport->vha->hw))
-			fcport->vha->hw->isp_ops->fabric_logout(fcport->vha,
-			    fcport->loop_id, fcport->d_id.b.domain,
-			    fcport->d_id.b.area, fcport->d_id.b.al_pa);
-		else
+		if (IS_FWI2_CAPABLE(fcport->vha->hw)) {
+			if (fcport->loop_id != FC_NO_LOOP_ID)
+				fcport->logout_on_delete = 1;
+
+			qlt_schedule_sess_for_deletion(fcport);
+		} else {
 			qla2x00_port_logout(fcport->vha, fcport);
+		}
 	}
 }
 

drivers/scsi/qla2xxx/qla_isr.c

@@ -2652,6 +2652,15 @@ static void qla24xx_nvme_iocb_entry(scsi_qla_host_t *vha, struct req_que *req,
 	case CS_PORT_UNAVAILABLE:
 	case CS_PORT_LOGGED_OUT:
 		fcport->nvme_flag |= NVME_FLAG_RESETTING;
+		if (atomic_read(&fcport->state) == FCS_ONLINE) {
+			ql_dbg(ql_dbg_disc, fcport->vha, 0x3021,
+			       "Port to be marked lost on fcport=%06x, current "
+			       "port state= %s comp_status %x.\n",
+			       fcport->d_id.b24, port_state_str[FCS_ONLINE],
+			       comp_status);
+
+			qlt_schedule_sess_for_deletion(fcport);
+		}
 		fallthrough;
 	case CS_ABORTED:
 	case CS_PORT_BUSY:

drivers/scsi/qla2xxx/qla_mbx.c

@@ -4190,6 +4190,16 @@ qla24xx_report_id_acquisition(scsi_qla_host_t *vha,
 				rptid_entry->u.f2.remote_nport_id[1];
 			fcport->d_id.b.al_pa =
 				rptid_entry->u.f2.remote_nport_id[0];
+
+			/*
+			 * For the case where remote port sending PRLO, FW
+			 * sends up RIDA Format 2 as an indication of session
+			 * loss. In other word, FW state change from PRLI
+			 * complete back to PLOGI complete. Delete the
+			 * session and let relogin drive the reconnect.
+			 */
+			if (atomic_read(&fcport->state) == FCS_ONLINE)
+				qlt_schedule_sess_for_deletion(fcport);
 		}
 	}
 }