pinctrl: aspeed: Fix GPIO requests on pass-through banks

Commit 6726fbff19bf ("pinctrl: aspeed: Fix GPI only function problem.")
fixes access to GPIO banks T and U on the AST2600. Both banks contain
input-only pins and the GPIO pin function is named GPITx and GPIUx
respectively. Unfortunately the fix had a negative impact on GPIO banks
D and E for the AST2400 and AST2500 where the GPIO pass-through
functions take similar "GPI"-style names. The net effect on the older
SoCs was that when the GPIO subsystem requested a pin in banks D or E be
muxed for GPIO, they were instead muxed for pass-through mode.
Mistakenly muxing pass-through mode e.g. breaks booting the host on
IBM's Witherspoon (AC922) platform where GPIOE0 is used for FSI.

Further exploit the names in the provided expression structure to
differentiate pass-through from pin-specific GPIO modes.

This follow-up fix gives the expected behaviour for the following tests:

Witherspoon BMC (AST2500):

1. Power-on the Witherspoon host
2. Request GPIOD1 be muxed via /sys/class/gpio/export
3. Request GPIOE1 be muxed via /sys/class/gpio/export
4. Request the balls for GPIOs E2 and E3 be muxed as GPIO pass-through
   ("GPIE2" mode) via a pinctrl hog in the devicetree

Rainier BMC (AST2600):

5. Request GPIT0 be muxed via /sys/class/gpio/export
6. Request GPIU0 be muxed via /sys/class/gpio/export

Together the tests demonstrate that all three pieces of functionality
(general GPIOs via 1, 2 and 3, input-only GPIOs via 5 and 6, pass-through
mode via 4) operate as desired across old and new SoCs.

Fixes: 9b92f5c5 ("pinctrl: aspeed: Fix GPI only function problem.")
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Tested-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Cc: Billy Tsai <billy_tsai@aspeedtech.com>
Cc: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20201126063337.489927-1-andrew@aj.id.auSigned-off-by: Linus Walleij <linus.walleij@linaro.org>

drivers/pinctrl/aspeed/pinctrl-aspeed.c

@@ -286,14 +286,76 @@ int aspeed_pinmux_set_mux(struct pinctrl_dev *pctldev, unsigned int function,
 static bool aspeed_expr_is_gpio(const struct aspeed_sig_expr *expr)
 {
 	/*
-	 * The signal type is GPIO if the signal name has "GPI" as a prefix.
-	 * strncmp (rather than strcmp) is used to implement the prefix
-	 * requirement.
+	 * We need to differentiate between GPIO and non-GPIO signals to
+	 * implement the gpio_request_enable() interface. For better or worse
+	 * the ASPEED pinctrl driver uses the expression names to determine
+	 * whether an expression will mux a pin for GPIO.
 	 *
-	 * expr->signal might look like "GPIOB1" in the GPIO case.
-	 * expr->signal might look like "GPIT0" in the GPI case.
+	 * Generally we have the following - A GPIO such as B1 has:
+	 *
+	 *    - expr->signal set to "GPIOB1"
+	 *    - expr->function set to "GPIOB1"
+	 *
+	 * Using this fact we can determine whether the provided expression is
+	 * a GPIO expression by testing the signal name for the string prefix
+	 * "GPIO".
+	 *
+	 * However, some GPIOs are input-only, and the ASPEED datasheets name
+	 * them differently. An input-only GPIO such as T0 has:
+	 *
+	 *    - expr->signal set to "GPIT0"
+	 *    - expr->function set to "GPIT0"
+	 *
+	 * It's tempting to generalise the prefix test from "GPIO" to "GPI" to
+	 * account for both GPIOs and GPIs, but in doing so we run aground on
+	 * another feature:
+	 *
+	 * Some pins in the ASPEED BMC SoCs have a "pass-through" GPIO
+	 * function where the input state of one pin is replicated as the
+	 * output state of another (as if they were shorted together - a mux
+	 * configuration that is typically enabled by hardware strapping).
+	 * This feature allows the BMC to pass e.g. power button state through
+	 * to the host while the BMC is yet to boot, but take control of the
+	 * button state once the BMC has booted by muxing each pin as a
+	 * separate, pin-specific GPIO.
+	 *
+	 * Conceptually this pass-through mode is a form of GPIO and is named
+	 * as such in the datasheets, e.g. "GPID0". This naming similarity
+	 * trips us up with the simple GPI-prefixed-signal-name scheme
+	 * discussed above, as the pass-through configuration is not what we
+	 * want when muxing a pin as GPIO for the GPIO subsystem.
+	 *
+	 * On e.g. the AST2400, a pass-through function "GPID0" is grouped on
+	 * balls A18 and D16, where we have:
+	 *
+	 *    For ball A18:
+	 *    - expr->signal set to "GPID0IN"
+	 *    - expr->function set to "GPID0"
+	 *
+	 *    For ball D16:
+	 *    - expr->signal set to "GPID0OUT"
+	 *    - expr->function set to "GPID0"
+	 *
+	 * By contrast, the pin-specific GPIO expressions for the same pins are
+	 * as follows:
+	 *
+	 *    For ball A18:
+	 *    - expr->signal looks like "GPIOD0"
+	 *    - expr->function looks like "GPIOD0"
+	 *
+	 *    For ball D16:
+	 *    - expr->signal looks like "GPIOD1"
+	 *    - expr->function looks like "GPIOD1"
+	 *
+	 * Testing both the signal _and_ function names gives us the means
+	 * differentiate the pass-through GPIO pinmux configuration from the
+	 * pin-specific configuration that the GPIO subsystem is after: An
+	 * expression is a pin-specific (non-pass-through) GPIO configuration
+	 * if the signal prefix is "GPI" and the signal name matches the
+	 * function name.
 	 */
-	return strncmp(expr->signal, "GPI", 3) == 0;
+	return !strncmp(expr->signal, "GPI", 3) &&
+			!strcmp(expr->signal, expr->function);
 }
 
 static bool aspeed_gpio_in_exprs(const struct aspeed_sig_expr **exprs)

drivers/pinctrl/aspeed/pinmux-aspeed.h

@@ -452,10 +452,11 @@ struct aspeed_sig_desc {
  * evaluation of the descriptors.
  *
  * @signal: The signal name for the priority level on the pin. If the signal
- *          type is GPIO, then the signal name must begin with the string
- *          "GPIO", e.g. GPIOA0, GPIOT4 etc.
+ *          type is GPIO, then the signal name must begin with the
+ *          prefix "GPI", e.g. GPIOA0, GPIT0 etc.
  * @function: The name of the function the signal participates in for the
- *            associated expression
+ *            associated expression. For pin-specific GPIO, the function
+ *            name must match the signal name.
  * @ndescs: The number of signal descriptors in the expression
  * @descs: Pointer to an array of signal descriptors that comprise the
  *         function expression