Commit 7c0fe360 authored by Mark Broadbent's avatar Mark Broadbent Committed by Linus Torvalds

[PATCH] IO-APIC debug message reduction

The APIC and IO-APIC code is very verbose on startup especially on SMP
machines.  This patch allows the verbosity of the APIC code to be controlled
through the boot-time option apic= using three levels: quiet, verbose and
debug.  The default level is quiet.
Signed-off-by: default avatarMark Broadbent <markb@wetlettuce.com>
Signed-off-by: default avatarAndrew Morton <akpm@osdl.org>
Signed-off-by: default avatarLinus Torvalds <torvalds@osdl.org>
parent 432818b9
......@@ -189,6 +189,11 @@ running once the system is up.
Disable APC CPU standby support. SPARCstation-Fox does
not play well with APC CPU idle - disable it if you have
APC and your system crashes randomly.
apic= [APIC,i386] Change the output verbosity whilst booting
Format: { quiet (default) | verbose | debug }
Change the amount of debugging information output
when initialising the APIC and IO-APIC components.
apm= [APM] Advanced Power Management
See header of arch/i386/kernel/apm.c.
......
......@@ -39,6 +39,12 @@
#include "io_ports.h"
/*
* Debug level
*/
int apic_verbosity;
static void apic_pm_activate(void);
void __init apic_intr_init(void)
......@@ -173,7 +179,8 @@ void __init connect_bsp_APIC(void)
* PIC mode, enable APIC mode in the IMCR, i.e.
* connect BSP's local APIC to INT and NMI lines.
*/
printk("leaving PIC mode, enabling APIC mode.\n");
apic_printk(APIC_VERBOSE, "leaving PIC mode, "
"enabling APIC mode.\n");
outb(0x70, 0x22);
outb(0x01, 0x23);
}
......@@ -189,7 +196,8 @@ void disconnect_bsp_APIC(void)
* interrupts, including IPIs, won't work beyond
* this point! The only exception are INIT IPIs.
*/
printk("disabling APIC mode, entering PIC mode.\n");
apic_printk(APIC_VERBOSE, "disabling APIC mode, "
"entering PIC mode.\n");
outb(0x70, 0x22);
outb(0x00, 0x23);
}
......@@ -230,10 +238,10 @@ int __init verify_local_APIC(void)
* The version register is read-only in a real APIC.
*/
reg0 = apic_read(APIC_LVR);
Dprintk("Getting VERSION: %x\n", reg0);
apic_printk(APIC_DEBUG, "Getting VERSION: %x\n", reg0);
apic_write(APIC_LVR, reg0 ^ APIC_LVR_MASK);
reg1 = apic_read(APIC_LVR);
Dprintk("Getting VERSION: %x\n", reg1);
apic_printk(APIC_DEBUG, "Getting VERSION: %x\n", reg1);
/*
* The two version reads above should print the same
......@@ -257,7 +265,7 @@ int __init verify_local_APIC(void)
* The ID register is read/write in a real APIC.
*/
reg0 = apic_read(APIC_ID);
Dprintk("Getting ID: %x\n", reg0);
apic_printk(APIC_DEBUG, "Getting ID: %x\n", reg0);
/*
* The next two are just to see if we have sane values.
......@@ -265,9 +273,9 @@ int __init verify_local_APIC(void)
* compatibility mode, but most boxes are anymore.
*/
reg0 = apic_read(APIC_LVT0);
Dprintk("Getting LVT0: %x\n", reg0);
apic_printk(APIC_DEBUG, "Getting LVT0: %x\n", reg0);
reg1 = apic_read(APIC_LVT1);
Dprintk("Getting LVT1: %x\n", reg1);
apic_printk(APIC_DEBUG, "Getting LVT1: %x\n", reg1);
return 1;
}
......@@ -279,7 +287,7 @@ void __init sync_Arb_IDs(void)
*/
apic_wait_icr_idle();
Dprintk("Synchronizing Arb IDs.\n");
apic_printk(APIC_DEBUG, "Synchronizing Arb IDs.\n");
apic_write_around(APIC_ICR, APIC_DEST_ALLINC | APIC_INT_LEVELTRIG
| APIC_DM_INIT);
}
......@@ -427,10 +435,12 @@ void __init setup_local_APIC (void)
value = apic_read(APIC_LVT0) & APIC_LVT_MASKED;
if (!smp_processor_id() && (pic_mode || !value)) {
value = APIC_DM_EXTINT;
printk("enabled ExtINT on CPU#%d\n", smp_processor_id());
apic_printk(APIC_VERBOSE, "enabled ExtINT on CPU#%d\n",
smp_processor_id());
} else {
value = APIC_DM_EXTINT | APIC_LVT_MASKED;
printk("masked ExtINT on CPU#%d\n", smp_processor_id());
apic_printk(APIC_VERBOSE, "masked ExtINT on CPU#%d\n",
smp_processor_id());
}
apic_write_around(APIC_LVT0, value);
......@@ -450,7 +460,8 @@ void __init setup_local_APIC (void)
if (maxlvt > 3) /* Due to the Pentium erratum 3AP. */
apic_write(APIC_ESR, 0);
value = apic_read(APIC_ESR);
printk("ESR value before enabling vector: %08lx\n", value);
apic_printk(APIC_VERBOSE, "ESR value before enabling vector:"
" %08lx\n", value);
value = ERROR_APIC_VECTOR; // enables sending errors
apic_write_around(APIC_LVTERR, value);
......@@ -460,7 +471,8 @@ void __init setup_local_APIC (void)
if (maxlvt > 3)
apic_write(APIC_ESR, 0);
value = apic_read(APIC_ESR);
printk("ESR value after enabling vector: %08lx\n", value);
apic_printk(APIC_VERBOSE, "ESR value after enabling vector:"
" %08lx\n", value);
} else {
if (esr_disable)
/*
......@@ -635,6 +647,21 @@ static int __init lapic_enable(char *str)
}
__setup("lapic", lapic_enable);
static int __init apic_set_verbosity(char *str)
{
if (strcmp("debug", str) == 0)
apic_verbosity = APIC_DEBUG;
else if (strcmp("verbose", str) == 0)
apic_verbosity = APIC_VERBOSE;
else
printk(KERN_WARNING "APIC Verbosity level %s not recognised"
" use apic=verbose or apic=debug", str);
return 0;
}
__setup("apic=", apic_set_verbosity);
static int __init detect_init_APIC (void)
{
u32 h, l, features;
......@@ -671,7 +698,8 @@ static int __init detect_init_APIC (void)
*/
rdmsr(MSR_IA32_APICBASE, l, h);
if (!(l & MSR_IA32_APICBASE_ENABLE)) {
printk("Local APIC disabled by BIOS -- reenabling.\n");
apic_printk(APIC_VERBOSE, "Local APIC disabled "
"by BIOS -- reenabling.\n");
l &= ~MSR_IA32_APICBASE_BASE;
l |= MSR_IA32_APICBASE_ENABLE | APIC_DEFAULT_PHYS_BASE;
wrmsr(MSR_IA32_APICBASE, l, h);
......@@ -698,7 +726,7 @@ static int __init detect_init_APIC (void)
if (nmi_watchdog != NMI_NONE)
nmi_watchdog = NMI_LOCAL_APIC;
printk("Found and enabled local APIC!\n");
apic_printk(APIC_VERBOSE, "Found and enabled local APIC!\n");
apic_pm_activate();
......@@ -725,7 +753,8 @@ void __init init_apic_mappings(void)
apic_phys = mp_lapic_addr;
set_fixmap_nocache(FIX_APIC_BASE, apic_phys);
Dprintk("mapped APIC to %08lx (%08lx)\n", APIC_BASE, apic_phys);
apic_printk(APIC_DEBUG, "mapped APIC to %08lx (%08lx)\n", APIC_BASE,
apic_phys);
/*
* Fetch the APIC ID of the BSP in case we have a
......@@ -755,7 +784,8 @@ void __init init_apic_mappings(void)
ioapic_phys = __pa(ioapic_phys);
}
set_fixmap_nocache(idx, ioapic_phys);
Dprintk("mapped IOAPIC to %08lx (%08lx)\n",
apic_printk(APIC_DEBUG, "mapped IOAPIC to "
"%08lx (%08lx)\n",
__fix_to_virt(idx), ioapic_phys);
idx++;
}
......@@ -894,7 +924,7 @@ int __init calibrate_APIC_clock(void)
int i;
const int LOOPS = HZ/10;
printk("calibrating APIC timer ...\n");
apic_printk(APIC_VERBOSE, "calibrating APIC timer ...\n");
/*
* Put whatever arbitrary (but long enough) timeout
......@@ -939,11 +969,13 @@ int __init calibrate_APIC_clock(void)
result = (tt1-tt2)*APIC_DIVISOR/LOOPS;
if (cpu_has_tsc)
printk("..... CPU clock speed is %ld.%04ld MHz.\n",
apic_printk(APIC_VERBOSE, "..... CPU clock speed is "
"%ld.%04ld MHz.\n",
((long)(t2-t1)/LOOPS)/(1000000/HZ),
((long)(t2-t1)/LOOPS)%(1000000/HZ));
printk("..... host bus clock speed is %ld.%04ld MHz.\n",
apic_printk(APIC_VERBOSE, "..... host bus clock speed is "
"%ld.%04ld MHz.\n",
result/(1000000/HZ),
result%(1000000/HZ));
......@@ -954,7 +986,7 @@ static unsigned int calibration_result;
void __init setup_boot_APIC_clock(void)
{
printk("Using local APIC timer interrupts.\n");
apic_printk(APIC_VERBOSE, "Using local APIC timer interrupts.\n");
using_apic_timer = 1;
local_irq_disable();
......
......@@ -706,13 +706,15 @@ static int __init ioapic_pirq_setup(char *str)
pirq_entries[i] = -1;
pirqs_enabled = 1;
printk(KERN_INFO "PIRQ redirection, working around broken MP-BIOS.\n");
apic_printk(APIC_VERBOSE, KERN_INFO
"PIRQ redirection, working around broken MP-BIOS.\n");
max = MAX_PIRQS;
if (ints[0] < MAX_PIRQS)
max = ints[0];
for (i = 0; i < max; i++) {
printk(KERN_DEBUG "... PIRQ%d -> IRQ %d\n", i, ints[i+1]);
apic_printk(APIC_VERBOSE, KERN_DEBUG
"... PIRQ%d -> IRQ %d\n", i, ints[i+1]);
/*
* PIRQs are mapped upside down, usually.
*/
......@@ -773,8 +775,8 @@ int IO_APIC_get_PCI_irq_vector(int bus, int slot, int pin)
{
int apic, i, best_guess = -1;
Dprintk("querying PCI -> IRQ mapping bus:%d, slot:%d, pin:%d.\n",
bus, slot, pin);
apic_printk(APIC_DEBUG, "querying PCI -> IRQ mapping bus:%d, "
"slot:%d, pin:%d.\n", bus, slot, pin);
if (mp_bus_id_to_pci_bus[bus] == -1) {
printk(KERN_WARNING "PCI BIOS passed nonexistent PCI bus %d!\n", bus);
return -1;
......@@ -842,7 +844,8 @@ static int __init EISA_ELCR(unsigned int irq)
unsigned int port = 0x4d0 + (irq >> 3);
return (inb(port) >> (irq & 7)) & 1;
}
printk(KERN_INFO "Broken MPtable reports ISA irq %d\n", irq);
apic_printk(APIC_VERBOSE, KERN_INFO
"Broken MPtable reports ISA irq %d\n", irq);
return 0;
}
......@@ -1084,10 +1087,12 @@ static int pin_2_irq(int idx, int apic, int pin)
if ((pin >= 16) && (pin <= 23)) {
if (pirq_entries[pin-16] != -1) {
if (!pirq_entries[pin-16]) {
printk(KERN_DEBUG "disabling PIRQ%d\n", pin-16);
apic_printk(APIC_VERBOSE, KERN_DEBUG
"disabling PIRQ%d\n", pin-16);
} else {
irq = pirq_entries[pin-16];
printk(KERN_DEBUG "using PIRQ%d -> IRQ %d\n",
apic_printk(APIC_VERBOSE, KERN_DEBUG
"using PIRQ%d -> IRQ %d\n",
pin-16, irq);
}
}
......@@ -1177,7 +1182,7 @@ void __init setup_IO_APIC_irqs(void)
int apic, pin, idx, irq, first_notcon = 1, vector;
unsigned long flags;
printk(KERN_DEBUG "init IO_APIC IRQs\n");
apic_printk(APIC_VERBOSE, KERN_DEBUG "init IO_APIC IRQs\n");
for (apic = 0; apic < nr_ioapics; apic++) {
for (pin = 0; pin < nr_ioapic_registers[apic]; pin++) {
......@@ -1196,10 +1201,14 @@ void __init setup_IO_APIC_irqs(void)
idx = find_irq_entry(apic,pin,mp_INT);
if (idx == -1) {
if (first_notcon) {
printk(KERN_DEBUG " IO-APIC (apicid-pin) %d-%d", mp_ioapics[apic].mpc_apicid, pin);
apic_printk(APIC_VERBOSE, KERN_DEBUG
" IO-APIC (apicid-pin) %d-%d",
mp_ioapics[apic].mpc_apicid,
pin);
first_notcon = 0;
} else
printk(", %d-%d", mp_ioapics[apic].mpc_apicid, pin);
apic_printk(APIC_VERBOSE, ", %d-%d",
mp_ioapics[apic].mpc_apicid, pin);
continue;
}
......@@ -1240,7 +1249,7 @@ void __init setup_IO_APIC_irqs(void)
}
if (!first_notcon)
printk(" not connected.\n");
apic_printk(APIC_VERBOSE, " not connected.\n");
}
/*
......@@ -1300,6 +1309,9 @@ void __init print_IO_APIC(void)
union IO_APIC_reg_03 reg_03;
unsigned long flags;
if (apic_verbosity == APIC_QUIET)
return;
printk(KERN_DEBUG "number of MP IRQ sources: %d.\n", mp_irq_entries);
for (i = 0; i < nr_ioapics; i++)
printk(KERN_DEBUG "number of IO-APIC #%d registers: %d.\n",
......@@ -1442,6 +1454,9 @@ static void print_APIC_bitfield (int base)
unsigned int v;
int i, j;
if (apic_verbosity == APIC_QUIET)
return;
printk(KERN_DEBUG "0123456789abcdef0123456789abcdef\n" KERN_DEBUG);
for (i = 0; i < 8; i++) {
v = apic_read(base + i*0x10);
......@@ -1459,6 +1474,9 @@ void /*__init*/ print_local_APIC(void * dummy)
{
unsigned int v, ver, maxlvt;
if (apic_verbosity == APIC_QUIET)
return;
printk("\n" KERN_DEBUG "printing local APIC contents on CPU#%d/%d:\n",
smp_processor_id(), hard_smp_processor_id());
v = apic_read(APIC_ID);
......@@ -1546,6 +1564,9 @@ void /*__init*/ print_PIC(void)
unsigned int v;
unsigned long flags;
if (apic_verbosity == APIC_QUIET)
return;
printk(KERN_DEBUG "\nprinting PIC contents\n");
spin_lock_irqsave(&i8259A_lock, flags);
......@@ -1681,7 +1702,9 @@ static void __init setup_ioapic_ids_from_mpc(void)
} else {
physid_mask_t tmp;
tmp = apicid_to_cpu_present(mp_ioapics[apic].mpc_apicid);
printk("Setting %d in the phys_id_present_map\n", mp_ioapics[apic].mpc_apicid);
apic_printk(APIC_VERBOSE, "Setting %d in the "
"phys_id_present_map\n",
mp_ioapics[apic].mpc_apicid);
physids_or(phys_id_present_map, phys_id_present_map, tmp);
}
......@@ -1700,8 +1723,9 @@ static void __init setup_ioapic_ids_from_mpc(void)
* Read the right value from the MPC table and
* write it into the ID register.
*/
printk(KERN_INFO "...changing IO-APIC physical APIC ID to %d ...",
mp_ioapics[apic].mpc_apicid);
apic_printk(APIC_VERBOSE, KERN_INFO
"...changing IO-APIC physical APIC ID to %d ...",
mp_ioapics[apic].mpc_apicid);
reg_00.bits.ID = mp_ioapics[apic].mpc_apicid;
spin_lock_irqsave(&ioapic_lock, flags);
......@@ -1717,7 +1741,7 @@ static void __init setup_ioapic_ids_from_mpc(void)
if (reg_00.bits.ID != mp_ioapics[apic].mpc_apicid)
panic("could not set ID!\n");
else
printk(" ok.\n");
apic_printk(APIC_VERBOSE, " ok.\n");
}
}
#else
......@@ -2032,11 +2056,11 @@ static void setup_nmi (void)
* is from Maciej W. Rozycki - so we do not have to EOI from
* the NMI handler or the timer interrupt.
*/
printk(KERN_INFO "activating NMI Watchdog ...");
apic_printk(APIC_VERBOSE, KERN_INFO "activating NMI Watchdog ...");
on_each_cpu(enable_NMI_through_LVT0, NULL, 1, 1);
printk(" done.\n");
apic_printk(APIC_VERBOSE, " done.\n");
}
/*
......@@ -2213,7 +2237,8 @@ static inline void check_timer(void)
return;
}
printk(" failed :(.\n");
panic("IO-APIC + timer doesn't work! Try using the 'noapic' kernel parameter\n");
panic("IO-APIC + timer doesn't work! Boot with apic=debug and send a "
"report. Then try booting with the 'noapic' option");
}
/*
......@@ -2427,7 +2452,8 @@ int __init io_apic_get_unique_id (int ioapic, int apic_id)
panic("IOAPIC[%d]: Unable change apic_id!\n", ioapic);
}
printk(KERN_INFO "IOAPIC[%d]: Assigned apic_id %d\n", ioapic, apic_id);
apic_printk(APIC_VERBOSE, KERN_INFO
"IOAPIC[%d]: Assigned apic_id %d\n", ioapic, apic_id);
return apic_id;
}
......@@ -2493,9 +2519,10 @@ int io_apic_set_pci_routing (int ioapic, int pin, int irq, int edge_level, int a
entry.vector = assign_irq_vector(irq);
Dprintk(KERN_DEBUG "IOAPIC[%d]: Set PCI routing entry (%d-%d -> 0x%x -> "
"IRQ %d Mode:%i Active:%i)\n", ioapic,
mp_ioapics[ioapic].mpc_apicid, pin, entry.vector, irq, edge_level, active_high_low);
apic_printk(APIC_DEBUG, KERN_DEBUG "IOAPIC[%d]: Set PCI routing entry "
"(%d-%d -> 0x%x -> IRQ %d Mode:%i Active:%i)\n", ioapic,
mp_ioapics[ioapic].mpc_apicid, pin, entry.vector, irq,
edge_level, active_high_low);
if (use_pci_vector() && !platform_legacy_irq(irq))
irq = IO_APIC_VECTOR(irq);
......
......@@ -7,13 +7,28 @@
#include <asm/apicdef.h>
#include <asm/system.h>
#define APIC_DEBUG 0
#if APIC_DEBUG
#define Dprintk(x...) printk(x)
#else
#define Dprintk(x...)
#endif
/*
* Debugging macros
*/
#define APIC_QUIET 0
#define APIC_VERBOSE 1
#define APIC_DEBUG 2
extern int apic_verbosity;
/*
* Define the default level of output to be very little
* This can be turned up by using apic=verbose for more
* information and apic=debug for _lots_ of information.
* apic_verbosity is defined in apic.c
*/
#define apic_printk(v, s, a...) do { \
if ((v) <= apic_verbosity) \
printk(s, ##a); \
} while (0)
#ifdef CONFIG_X86_LOCAL_APIC
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment