Merge branches 'thermal-core', 'thermal-intel' and 'thermal-soc' into next

Documentation/devicetree/bindings/thermal/rockchip-thermal.txt

@@ -12,6 +12,11 @@ Required properties:
 - resets : Must contain an entry for each entry in reset-names.
 	   See ../reset/reset.txt for details.
 - reset-names : Must include the name "tsadc-apb".
+- pinctrl-names : The pin control state names;
+- pinctrl-0 : The "init" pinctrl state, it will be set before device probe.
+- pinctrl-1 : The "default" pinctrl state, it will be set after reset the
+	      TSADC controller.
+- pinctrl-2 : The "sleep" pinctrl state, it will be in for suspend.
 - #thermal-sensor-cells : Should be 1. See ./thermal.txt for a description.
 - rockchip,hw-tshut-temp : The hardware-controlled shutdown temperature value.
 - rockchip,hw-tshut-mode : The hardware-controlled shutdown mode 0:CRU 1:GPIO.
@@ -27,8 +32,10 @@ tsadc: tsadc@ff280000 {
 	clock-names = "tsadc", "apb_pclk";
 	resets = <&cru SRST_TSADC>;
 	reset-names = "tsadc-apb";
-	pinctrl-names = "default";
-	pinctrl-0 = <&otp_out>;
+	pinctrl-names = "init", "default", "sleep";
+	pinctrl-0 = <&otp_gpio>;
+	pinctrl-1 = <&otp_out>;
+	pinctrl-2 = <&otp_gpio>;
 	#thermal-sensor-cells = <1>;
 	rockchip,hw-tshut-temp = <95000>;
 	rockchip,hw-tshut-mode = <0>;

Documentation/devicetree/bindings/thermal/ti_soc_thermal.txt

@@ -10,6 +10,8 @@ to the silicon temperature.
 
 Required properties:
 - compatible : Should be:
+  - "ti,omap34xx-bandgap" : for OMAP34xx bandgap
+  - "ti,omap36xx-bandgap" : for OMAP36xx bandgap
   - "ti,omap4430-bandgap" : for OMAP4430 bandgap
   - "ti,omap4460-bandgap" : for OMAP4460 bandgap
   - "ti,omap4470-bandgap" : for OMAP4470 bandgap
@@ -25,6 +27,18 @@ to each bandgap version, because the mapping may change from
 soc to soc, apart of depending on available features.
 
 Example:
+OMAP34xx:
+bandgap {
+	reg = <0x48002524 0x4>;
+	compatible = "ti,omap34xx-bandgap";
+};
+
+OMAP36xx:
+bandgap {
+	reg = <0x48002524 0x4>;
+	compatible = "ti,omap36xx-bandgap";
+};
+
 OMAP4430:
 bandgap {
 	reg = <0x4a002260 0x4 0x4a00232C 0x4>;

drivers/base/power/opp.c

@@ -217,7 +217,7 @@ static struct device_opp *_find_device_opp(struct device *dev)
 }
 
 /**
- * dev_pm_opp_get_voltage() - Gets the voltage corresponding to an available opp
+ * dev_pm_opp_get_voltage() - Gets the voltage corresponding to an opp
  * @opp:	opp for which voltage has to be returned for
  *
  * Return: voltage in micro volt corresponding to the opp, else
@@ -239,7 +239,7 @@ unsigned long dev_pm_opp_get_voltage(struct dev_pm_opp *opp)
 	opp_rcu_lockdep_assert();
 
 	tmp_opp = rcu_dereference(opp);
-	if (IS_ERR_OR_NULL(tmp_opp) || !tmp_opp->available)
+	if (IS_ERR_OR_NULL(tmp_opp))
 		pr_err("%s: Invalid parameters\n", __func__);
 	else
 		v = tmp_opp->u_volt;

drivers/thermal/Kconfig

@@ -147,6 +147,20 @@ config CLOCK_THERMAL
 	  device that is configured to use this cooling mechanism will be
 	  controlled to reduce clock frequency whenever temperature is high.
 
+config DEVFREQ_THERMAL
+	bool "Generic device cooling support"
+	depends on PM_DEVFREQ
+	depends on PM_OPP
+	help
+	  This implements the generic devfreq cooling mechanism through
+	  frequency reduction for devices using devfreq.
+
+	  This will throttle the device by limiting the maximum allowed DVFS
+	  frequency corresponding to the cooling level.
+
+	  In order to use the power extensions of the cooling device,
+	  devfreq should use the simple_ondemand governor.
+
 	  If you want this support, you should say Y here.
 
 config THERMAL_EMULATION
@@ -275,6 +289,7 @@ config X86_PKG_TEMP_THERMAL
 	tristate "X86 package temperature thermal driver"
 	depends on X86_THERMAL_VECTOR
 	select THERMAL_GOV_USER_SPACE
+	select THERMAL_WRITABLE_TRIPS
 	default m
 	help
 	  Enable this to register CPU digital sensor for package temperature as
@@ -296,6 +311,7 @@ config INTEL_SOC_DTS_THERMAL
 	tristate "Intel SoCs DTS thermal driver"
 	depends on X86
 	select INTEL_SOC_DTS_IOSF_CORE
+	select THERMAL_WRITABLE_TRIPS
 	help
 	  Enable this to register Intel SoCs (e.g. Bay Trail) platform digital
 	  temperature sensor (DTS). These SoCs have two additional DTSs in
@@ -322,6 +338,7 @@ config INT340X_THERMAL
 	select ACPI_THERMAL_REL
 	select ACPI_FAN
 	select INTEL_SOC_DTS_IOSF_CORE
+	select THERMAL_WRITABLE_TRIPS
 	help
 	  Newer laptops and tablets that use ACPI may have thermal sensors and
 	  other devices with thermal control capabilities outside the core

drivers/thermal/Makefile

@@ -22,6 +22,9 @@ thermal_sys-$(CONFIG_CPU_THERMAL)	+= cpu_cooling.o
 # clock cooling
 thermal_sys-$(CONFIG_CLOCK_THERMAL)	+= clock_cooling.o
 
+# devfreq cooling
+thermal_sys-$(CONFIG_DEVFREQ_THERMAL) += devfreq_cooling.o
+
 # platform thermal drivers
 obj-$(CONFIG_QCOM_SPMI_TEMP_ALARM)	+= qcom-spmi-temp-alarm.o
 obj-$(CONFIG_SPEAR_THERMAL)	+= spear_thermal.o

drivers/thermal/armada_thermal.c

@@ -224,9 +224,9 @@ static const struct armada_thermal_data armada380_data = {
 	.is_valid_shift = 10,
 	.temp_shift = 0,
 	.temp_mask = 0x3ff,
-	.coef_b = 2931108200UL,
-	.coef_m = 5000000UL,
-	.coef_div = 10502,
+	.coef_b = 1172499100UL,
+	.coef_m = 2000096UL,
+	.coef_div = 4201,
 	.inverted = true,
 };
 

drivers/thermal/imx_thermal.c

@@ -288,7 +288,7 @@ static int imx_set_trip_temp(struct thermal_zone_device *tz, int trip,
 	if (trip == IMX_TRIP_CRITICAL)
 		return -EPERM;
 
-	if (temp > IMX_TEMP_PASSIVE)
+	if (temp < 0 || temp > IMX_TEMP_PASSIVE)
 		return -EINVAL;
 
 	data->temp_passive = temp;
@@ -487,14 +487,6 @@ static int imx_thermal_probe(struct platform_device *pdev)
 	if (data->irq < 0)
 		return data->irq;
 
-	ret = devm_request_threaded_irq(&pdev->dev, data->irq,
-			imx_thermal_alarm_irq, imx_thermal_alarm_irq_thread,
-			0, "imx_thermal", data);
-	if (ret < 0) {
-		dev_err(&pdev->dev, "failed to request alarm irq: %d\n", ret);
-		return ret;
-	}
-
 	platform_set_drvdata(pdev, data);
 
 	ret = imx_get_sensor_data(pdev);
@@ -571,6 +563,17 @@ static int imx_thermal_probe(struct platform_device *pdev)
 	regmap_write(map, TEMPSENSE0 + REG_CLR, TEMPSENSE0_POWER_DOWN);
 	regmap_write(map, TEMPSENSE0 + REG_SET, TEMPSENSE0_MEASURE_TEMP);
 
+	ret = devm_request_threaded_irq(&pdev->dev, data->irq,
+			imx_thermal_alarm_irq, imx_thermal_alarm_irq_thread,
+			0, "imx_thermal", data);
+	if (ret < 0) {
+		dev_err(&pdev->dev, "failed to request alarm irq: %d\n", ret);
+		clk_disable_unprepare(data->thermal_clk);
+		thermal_zone_device_unregister(data->tz);
+		cpufreq_cooling_unregister(data->cdev);
+		return ret;
+	}
+
 	data->irq_enabled = true;
 	data->mode = THERMAL_DEVICE_ENABLED;
 

drivers/thermal/rockchip_thermal.c

@@ -106,16 +106,14 @@ struct rockchip_thermal_data {
 #define TSADCV2_AUTO_PERIOD_HT			0x6c
 
 #define TSADCV2_AUTO_EN				BIT(0)
-#define TSADCV2_AUTO_DISABLE			~BIT(0)
 #define TSADCV2_AUTO_SRC_EN(chn)		BIT(4 + (chn))
 #define TSADCV2_AUTO_TSHUT_POLARITY_HIGH	BIT(8)
-#define TSADCV2_AUTO_TSHUT_POLARITY_LOW		~BIT(8)
 
 #define TSADCV2_INT_SRC_EN(chn)			BIT(chn)
 #define TSADCV2_SHUT_2GPIO_SRC_EN(chn)		BIT(4 + (chn))
 #define TSADCV2_SHUT_2CRU_SRC_EN(chn)		BIT(8 + (chn))
 
-#define TSADCV2_INT_PD_CLEAR			~BIT(8)
+#define TSADCV2_INT_PD_CLEAR_MASK		~BIT(8)
 
 #define TSADCV2_DATA_MASK			0xfff
 #define TSADCV2_HIGHT_INT_DEBOUNCE_COUNT	4
@@ -124,7 +122,7 @@ struct rockchip_thermal_data {
 #define TSADCV2_AUTO_PERIOD_HT_TIME		50  /* msec */
 
 struct tsadc_table {
-	unsigned long code;
+	u32 code;
 	long temp;
 };
 
@@ -164,7 +162,6 @@ static const struct tsadc_table v2_code_table[] = {
 	{3452, 115000},
 	{3437, 120000},
 	{3421, 125000},
-	{0, 125000},
 };
 
 static u32 rk_tsadcv2_temp_to_code(long temp)
@@ -191,19 +188,21 @@ static u32 rk_tsadcv2_temp_to_code(long temp)
 	return 0;
 }
 
-static int rk_tsadcv2_code_to_temp(u32 code)
+static int rk_tsadcv2_code_to_temp(u32 code, int *temp)
 {
-	unsigned int low = 0;
+	unsigned int low = 1;
 	unsigned int high = ARRAY_SIZE(v2_code_table) - 1;
 	unsigned int mid = (low + high) / 2;
 	unsigned int num;
 	unsigned long denom;
 
-	/* Invalid code, return -EAGAIN */
-	if (code > TSADCV2_DATA_MASK)
-		return -EAGAIN;
+	BUILD_BUG_ON(ARRAY_SIZE(v2_code_table) < 2);
 
-	while (low <= high && mid) {
+	code &= TSADCV2_DATA_MASK;
+	if (code < v2_code_table[high].code)
+		return -EAGAIN;		/* Incorrect reading */
+
+	while (low <= high) {
 		if (code >= v2_code_table[mid].code &&
 		    code < v2_code_table[mid - 1].code)
 			break;
@@ -223,7 +222,9 @@ static int rk_tsadcv2_code_to_temp(u32 code)
 	num = v2_code_table[mid].temp - v2_code_table[mid - 1].temp;
 	num *= v2_code_table[mid - 1].code - code;
 	denom = v2_code_table[mid - 1].code - v2_code_table[mid].code;
-	return v2_code_table[mid - 1].temp + (num / denom);
+	*temp = v2_code_table[mid - 1].temp + (num / denom);
+
+	return 0;
 }
 
 /**
@@ -241,10 +242,10 @@ static void rk_tsadcv2_initialize(void __iomem *regs,
 				  enum tshut_polarity tshut_polarity)
 {
 	if (tshut_polarity == TSHUT_HIGH_ACTIVE)
-		writel_relaxed(0 | (TSADCV2_AUTO_TSHUT_POLARITY_HIGH),
+		writel_relaxed(0U | TSADCV2_AUTO_TSHUT_POLARITY_HIGH,
 			       regs + TSADCV2_AUTO_CON);
 	else
-		writel_relaxed(0 | (TSADCV2_AUTO_TSHUT_POLARITY_LOW),
+		writel_relaxed(0U & ~TSADCV2_AUTO_TSHUT_POLARITY_HIGH,
 			       regs + TSADCV2_AUTO_CON);
 
 	writel_relaxed(TSADCV2_AUTO_PERIOD_TIME, regs + TSADCV2_AUTO_PERIOD);
@@ -261,7 +262,7 @@ static void rk_tsadcv2_irq_ack(void __iomem *regs)
 	u32 val;
 
 	val = readl_relaxed(regs + TSADCV2_INT_PD);
-	writel_relaxed(val & TSADCV2_INT_PD_CLEAR, regs + TSADCV2_INT_PD);
+	writel_relaxed(val & TSADCV2_INT_PD_CLEAR_MASK, regs + TSADCV2_INT_PD);
 }
 
 static void rk_tsadcv2_control(void __iomem *regs, bool enable)
@@ -281,14 +282,9 @@ static int rk_tsadcv2_get_temp(int chn, void __iomem *regs, int *temp)
 {
 	u32 val;
 
-	/* the A/D value of the channel last conversion need some time */
 	val = readl_relaxed(regs + TSADCV2_DATA(chn));
-	if (val == 0)
-		return -EAGAIN;
 
-	*temp = rk_tsadcv2_code_to_temp(val);
-
-	return 0;
+	return rk_tsadcv2_code_to_temp(val, temp);
 }
 
 static void rk_tsadcv2_tshut_temp(int chn, void __iomem *regs, long temp)
@@ -642,6 +638,8 @@ static int __maybe_unused rockchip_thermal_suspend(struct device *dev)
 	clk_disable(thermal->pclk);
 	clk_disable(thermal->clk);
 
+	pinctrl_pm_select_sleep_state(dev);
+
 	return 0;
 }
 
@@ -678,6 +676,8 @@ static int __maybe_unused rockchip_thermal_resume(struct device *dev)
 	for (i = 0; i < ARRAY_SIZE(thermal->sensors); i++)
 		rockchip_thermal_toggle_sensor(&thermal->sensors[i], true);
 
+	pinctrl_pm_select_default_state(dev);
+
 	return 0;
 }
 

drivers/thermal/samsung/exynos_tmu.c

@@ -548,7 +548,7 @@ static int exynos5433_tmu_initialize(struct platform_device *pdev)
 	default:
 		pdata->cal_type = TYPE_ONE_POINT_TRIMMING;
 		break;
-	};
+	}
 
 	dev_info(&pdev->dev, "Calibration type is %d-point calibration\n",
 			cal_type ?  2 : 1);
@@ -608,7 +608,7 @@ static int exynos5440_tmu_initialize(struct platform_device *pdev)
 {
 	struct exynos_tmu_data *data = platform_get_drvdata(pdev);
 	unsigned int trim_info = 0, con, rising_threshold;
-	int ret = 0, threshold_code;
+	int threshold_code;
 	int crit_temp = 0;
 
 	/*
@@ -651,7 +651,8 @@ static int exynos5440_tmu_initialize(struct platform_device *pdev)
 	/* Clear the PMIN in the common TMU register */
 	if (!data->id)
 		writel(0, data->base_second + EXYNOS5440_TMU_PMIN);
-	return ret;
+
+	return 0;
 }
 
 static int exynos7_tmu_initialize(struct platform_device *pdev)
@@ -1168,27 +1169,10 @@ static int exynos_map_dt_data(struct platform_device *pdev)
 	struct exynos_tmu_data *data = platform_get_drvdata(pdev);
 	struct exynos_tmu_platform_data *pdata;
 	struct resource res;
-	int ret;
 
 	if (!data || !pdev->dev.of_node)
 		return -ENODEV;
 
-	/*
-	 * Try enabling the regulator if found
-	 * TODO: Add regulator as an SOC feature, so that regulator enable
-	 * is a compulsory call.
-	 */
-	data->regulator = devm_regulator_get(&pdev->dev, "vtmu");
-	if (!IS_ERR(data->regulator)) {
-		ret = regulator_enable(data->regulator);
-		if (ret) {
-			dev_err(&pdev->dev, "failed to enable vtmu\n");
-			return ret;
-		}
-	} else {
-		dev_info(&pdev->dev, "Regulator node (vtmu) not found\n");
-	}
-
 	data->id = of_alias_get_id(pdev->dev.of_node, "tmuctrl");
 	if (data->id < 0)
 		data->id = 0;
@@ -1306,12 +1290,22 @@ static int exynos_tmu_probe(struct platform_device *pdev)
 	platform_set_drvdata(pdev, data);
 	mutex_init(&data->lock);
 
-	data->tzd = thermal_zone_of_sensor_register(&pdev->dev, 0, data,
-						    &exynos_sensor_ops);
-	if (IS_ERR(data->tzd)) {
-		pr_err("thermal: tz: %p ERROR\n", data->tzd);
-		return PTR_ERR(data->tzd);
+	/*
+	 * Try enabling the regulator if found
+	 * TODO: Add regulator as an SOC feature, so that regulator enable
+	 * is a compulsory call.
+	 */
+	data->regulator = devm_regulator_get(&pdev->dev, "vtmu");
+	if (!IS_ERR(data->regulator)) {
+		ret = regulator_enable(data->regulator);
+		if (ret) {
+			dev_err(&pdev->dev, "failed to enable vtmu\n");
+			return ret;
+		}
+	} else {
+		dev_info(&pdev->dev, "Regulator node (vtmu) not found\n");
 	}
+
 	ret = exynos_map_dt_data(pdev);
 	if (ret)
 		goto err_sensor;
@@ -1363,23 +1357,38 @@ static int exynos_tmu_probe(struct platform_device *pdev)
 		break;
 	default:
 		break;
-	};
+	}
+
+	/*
+	 * data->tzd must be registered before calling exynos_tmu_initialize(),
+	 * requesting irq and calling exynos_tmu_control().
+	 */
+	data->tzd = thermal_zone_of_sensor_register(&pdev->dev, 0, data,
+						    &exynos_sensor_ops);
+	if (IS_ERR(data->tzd)) {
+		ret = PTR_ERR(data->tzd);
+		dev_err(&pdev->dev, "Failed to register sensor: %d\n", ret);
+		goto err_sclk;
+	}
 
 	ret = exynos_tmu_initialize(pdev);
 	if (ret) {
 		dev_err(&pdev->dev, "Failed to initialize TMU\n");
-		goto err_sclk;
+		goto err_thermal;
 	}
 
 	ret = devm_request_irq(&pdev->dev, data->irq, exynos_tmu_irq,
 		IRQF_TRIGGER_RISING | IRQF_SHARED, dev_name(&pdev->dev), data);
 	if (ret) {
 		dev_err(&pdev->dev, "Failed to request irq: %d\n", data->irq);
-		goto err_sclk;
+		goto err_thermal;
 	}
 
 	exynos_tmu_control(pdev, true);
 	return 0;
+
+err_thermal:
+	thermal_zone_of_sensor_unregister(&pdev->dev, data->tzd);
 err_sclk:
 	clk_disable_unprepare(data->sclk);
 err_clk:
@@ -1388,9 +1397,8 @@ static int exynos_tmu_probe(struct platform_device *pdev)
 	if (!IS_ERR(data->clk_sec))
 		clk_unprepare(data->clk_sec);
 err_sensor:
-	if (!IS_ERR_OR_NULL(data->regulator))
+	if (!IS_ERR(data->regulator))
 		regulator_disable(data->regulator);
-	thermal_zone_of_sensor_unregister(&pdev->dev, data->tzd);
 
 	return ret;
 }

drivers/thermal/ti-soc-thermal/Kconfig

@@ -19,6 +19,21 @@ config TI_THERMAL
 	  This includes trip points definitions, extrapolation rules and
 	  CPU cooling device bindings.
 
+config OMAP3_THERMAL
+	bool "Texas Instruments OMAP3 thermal support"
+	depends on TI_SOC_THERMAL
+	depends on ARCH_OMAP3 || COMPILE_TEST
+	help
+	  If you say yes here you get thermal support for the Texas Instruments
+	  OMAP3 SoC family. The current chips supported are:
+	   - OMAP3430
+
+	  OMAP3 chips normally don't need thermal management, and sensors in
+	  this generation are not accurate, nor they are very close to
+	  the important hotspots.
+
+	  Say 'N' here.
+
 config OMAP4_THERMAL
 	bool "Texas Instruments OMAP4 thermal support"
 	depends on TI_SOC_THERMAL

drivers/thermal/ti-soc-thermal/Makefile

@@ -2,5 +2,6 @@ obj-$(CONFIG_TI_SOC_THERMAL)		+= ti-soc-thermal.o
 ti-soc-thermal-y			:= ti-bandgap.o
 ti-soc-thermal-$(CONFIG_TI_THERMAL)	+= ti-thermal-common.o
 ti-soc-thermal-$(CONFIG_DRA752_THERMAL)	+= dra752-thermal-data.o
+ti-soc-thermal-$(CONFIG_OMAP3_THERMAL)	+= omap3-thermal-data.o
 ti-soc-thermal-$(CONFIG_OMAP4_THERMAL)	+= omap4-thermal-data.o
 ti-soc-thermal-$(CONFIG_OMAP5_THERMAL)	+= omap5-thermal-data.o

drivers/thermal/ti-soc-thermal/omap3-thermal-data.c

+/*
+ * OMAP3 thermal driver.
+ *
+ * Copyright (C) 2011-2012 Texas Instruments Inc.
+ * Copyright (C) 2014 Pavel Machek <pavel@ucw.cz>
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Note
+ * http://www.ti.com/lit/er/sprz278f/sprz278f.pdf "Advisory
+ * 3.1.1.186 MMC OCP Clock Not Gated When Thermal Sensor Is Used"
+ *
+ * Also TI says:
+ * Just be careful when you try to make thermal policy like decisions
+ * based on this sensor. Placement of the sensor w.r.t the actual logic
+ * generating heat has to be a factor as well. If you are just looking
+ * for an approximation temperature (thermometerish kind), you might be
+ * ok with this. I am not sure we'd find any TI data around this.. just a
+ * heads up.
+ */
+
+#include "ti-thermal.h"
+#include "ti-bandgap.h"
+
+/*
+ * OMAP34XX has one instance of thermal sensor for MPU
+ * need to describe the individual bit fields
+ */
+static struct temp_sensor_registers
+omap34xx_mpu_temp_sensor_registers = {
+	.temp_sensor_ctrl = 0,
+	.bgap_soc_mask = BIT(8),
+	.bgap_eocz_mask = BIT(7),
+	.bgap_dtemp_mask = 0x7f,
+
+	.bgap_mode_ctrl = 0,
+	.mode_ctrl_mask = BIT(9),
+};
+
+/* Thresholds and limits for OMAP34XX MPU temperature sensor */
+static struct temp_sensor_data omap34xx_mpu_temp_sensor_data = {
+	.min_freq = 32768,
+	.max_freq = 32768,
+	.max_temp = 125000,
+	.min_temp = -40000,
+	.hyst_val = 5000,
+};
+
+/*
+ * Temperature values in milli degree celsius
+ */
+static const int
+omap34xx_adc_to_temp[128] = {
+	-40000, -40000, -40000, -40000, -40000, -39000, -38000, -36000,
+	-34000, -32000, -31000,	-29000, -28000, -26000, -25000, -24000,
+	-22000, -21000, -19000, -18000, -17000, -15000,	-14000, -12000,
+	-11000, -9000, -8000, -7000, -5000, -4000, -2000, -1000, 0000,
+	1000, 3000, 4000, 5000, 7000, 8000, 10000, 11000, 13000, 14000,
+	15000, 17000, 18000, 20000, 21000, 22000, 24000, 25000, 27000,
+	28000, 30000, 31000, 32000, 34000, 35000, 37000, 38000, 39000,
+	41000, 42000, 44000, 45000, 47000, 48000, 49000, 51000, 52000,
+	53000, 55000, 56000, 58000, 59000, 60000, 62000, 63000, 65000,
+	66000, 67000, 69000, 70000, 72000, 73000, 74000, 76000, 77000,
+	79000, 80000, 81000, 83000, 84000, 85000, 87000, 88000, 89000,
+	91000, 92000, 94000, 95000, 96000, 98000, 99000, 100000,
+	102000, 103000, 105000, 106000, 107000, 109000, 110000, 111000,
+	113000, 114000, 116000, 117000, 118000, 120000, 121000, 122000,
+	124000, 124000, 125000, 125000, 125000, 125000,	125000
+};
+
+/* OMAP34XX data */
+const struct ti_bandgap_data omap34xx_data = {
+	.features = TI_BANDGAP_FEATURE_CLK_CTRL | TI_BANDGAP_FEATURE_UNRELIABLE,
+	.fclock_name = "ts_fck",
+	.div_ck_name = "ts_fck",
+	.conv_table = omap34xx_adc_to_temp,
+	.adc_start_val = 0,
+	.adc_end_val = 127,
+	.expose_sensor = ti_thermal_expose_sensor,
+	.remove_sensor = ti_thermal_remove_sensor,
+
+	.sensors = {
+		{
+		.registers = &omap34xx_mpu_temp_sensor_registers,
+		.ts_data = &omap34xx_mpu_temp_sensor_data,
+		.domain = "cpu",
+		.slope = 0,
+		.constant = 20000,
+		.slope_pcb = 0,
+		.constant_pcb = 20000,
+		.register_cooling = NULL,
+		.unregister_cooling = NULL,
+		},
+	},
+	.sensor_count = 1,
+};
+
+/*
+ * OMAP36XX has one instance of thermal sensor for MPU
+ * need to describe the individual bit fields
+ */
+static struct temp_sensor_registers
+omap36xx_mpu_temp_sensor_registers = {
+	.temp_sensor_ctrl = 0,
+	.bgap_soc_mask = BIT(9),
+	.bgap_eocz_mask = BIT(8),
+	.bgap_dtemp_mask = 0xFF,
+
+	.bgap_mode_ctrl = 0,
+	.mode_ctrl_mask = BIT(10),
+};
+
+/* Thresholds and limits for OMAP36XX MPU temperature sensor */
+static struct temp_sensor_data omap36xx_mpu_temp_sensor_data = {
+	.min_freq = 32768,
+	.max_freq = 32768,
+	.max_temp = 125000,
+	.min_temp = -40000,
+	.hyst_val = 5000,
+};
+
+/*
+ * Temperature values in milli degree celsius
+ */
+static const int
+omap36xx_adc_to_temp[128] = {
+	-40000, -40000, -40000, -40000, -40000, -40000, -40000, -40000,
+	-40000, -40000, -40000,	-40000, -40000, -38000, -35000, -34000,
+	-32000, -30000, -28000, -26000, -24000, -22000,	-20000, -18500,
+	-17000, -15000, -13500, -12000, -10000, -8000, -6500, -5000, -3500,
+	-1500, 0, 2000, 3500, 5000, 6500, 8500, 10000, 12000, 13500,
+	15000, 17000, 19000, 21000, 23000, 25000, 27000, 28500, 30000,
+	32000, 33500, 35000, 37000, 38500, 40000, 42000, 43500, 45000,
+	47000, 48500, 50000, 52000, 53500, 55000, 57000, 58500, 60000,
+	62000, 64000, 66000, 68000, 70000, 71500, 73500, 75000, 77000,
+	78500, 80000, 82000, 83500, 85000, 87000, 88500, 90000, 92000,
+	93500, 95000, 97000, 98500, 100000, 102000, 103500, 105000, 107000,
+	109000, 111000, 113000, 115000, 117000, 118500, 120000, 122000,
+	123500, 125000, 125000, 125000, 125000, 125000, 125000, 125000,
+	125000, 125000, 125000, 125000, 125000, 125000, 125000, 125000,
+	125000, 125000, 125000, 125000, 125000, 125000,	125000
+};
+
+/* OMAP36XX data */
+const struct ti_bandgap_data omap36xx_data = {
+	.features = TI_BANDGAP_FEATURE_CLK_CTRL | TI_BANDGAP_FEATURE_UNRELIABLE,
+	.fclock_name = "ts_fck",
+	.div_ck_name = "ts_fck",
+	.conv_table = omap36xx_adc_to_temp,
+	.adc_start_val = 0,
+	.adc_end_val = 127,
+	.expose_sensor = ti_thermal_expose_sensor,
+	.remove_sensor = ti_thermal_remove_sensor,
+
+	.sensors = {
+		{
+		.registers = &omap36xx_mpu_temp_sensor_registers,
+		.ts_data = &omap36xx_mpu_temp_sensor_data,
+		.domain = "cpu",
+		.slope = 0,
+		.constant = 20000,
+		.slope_pcb = 0,
+		.constant_pcb = 20000,
+		.register_cooling = NULL,
+		.unregister_cooling = NULL,
+		},
+	},
+	.sensor_count = 1,
+};

drivers/thermal/ti-soc-thermal/ti-bandgap.c

@@ -1274,6 +1274,10 @@ int ti_bandgap_probe(struct platform_device *pdev)
 	}
 	bgp->dev = &pdev->dev;
 
+	if (TI_BANDGAP_HAS(bgp, UNRELIABLE))
+		dev_warn(&pdev->dev,
+			 "This OMAP thermal sensor is unreliable. You've been warned\n");
+
 	if (TI_BANDGAP_HAS(bgp, TSHUT)) {
 		ret = ti_bandgap_tshut_init(bgp, pdev);
 		if (ret) {
@@ -1579,6 +1583,16 @@ static SIMPLE_DEV_PM_OPS(ti_bandgap_dev_pm_ops, ti_bandgap_suspend,
 #endif
 
 static const struct of_device_id of_ti_bandgap_match[] = {
+#ifdef CONFIG_OMAP3_THERMAL
+	{
+		.compatible = "ti,omap34xx-bandgap",
+		.data = (void *)&omap34xx_data,
+	},
+	{
+		.compatible = "ti,omap36xx-bandgap",
+		.data = (void *)&omap36xx_data,
+	},
+#endif
 #ifdef CONFIG_OMAP4_THERMAL
 	{
 		.compatible = "ti,omap4430-bandgap",

drivers/thermal/ti-soc-thermal/ti-bandgap.h

@@ -322,6 +322,8 @@ struct ti_temp_sensor {
  *	has Errata 814
  * TI_BANDGAP_FEATURE_ERRATA_813 - used to workaorund when the bandgap device
  *	has Errata 813
+ * TI_BANDGAP_FEATURE_UNRELIABLE - used when the sensor readings are too
+ *	inaccurate.
  * TI_BANDGAP_HAS(b, f) - macro to check if a bandgap device is capable of a
  *      specific feature (above) or not. Return non-zero, if yes.
  */
@@ -337,6 +339,7 @@ struct ti_temp_sensor {
 #define TI_BANDGAP_FEATURE_HISTORY_BUFFER	BIT(9)
 #define TI_BANDGAP_FEATURE_ERRATA_814		BIT(10)
 #define TI_BANDGAP_FEATURE_ERRATA_813		BIT(11)
+#define TI_BANDGAP_FEATURE_UNRELIABLE		BIT(12)
 #define TI_BANDGAP_HAS(b, f)			\
 			((b)->conf->features & TI_BANDGAP_FEATURE_ ## f)
 
@@ -390,6 +393,14 @@ int ti_bandgap_set_sensor_data(struct ti_bandgap *bgp, int id, void *data);
 void *ti_bandgap_get_sensor_data(struct ti_bandgap *bgp, int id);
 int ti_bandgap_get_trend(struct ti_bandgap *bgp, int id, int *trend);
 
+#ifdef CONFIG_OMAP3_THERMAL
+extern const struct ti_bandgap_data omap34xx_data;
+extern const struct ti_bandgap_data omap36xx_data;
+#else
+#define omap34xx_data					NULL
+#define omap36xx_data					NULL
+#endif
+
 #ifdef CONFIG_OMAP4_THERMAL
 extern const struct ti_bandgap_data omap4430_data;
 extern const struct ti_bandgap_data omap4460_data;

include/linux/devfreq_cooling.h

+/*
+ * devfreq_cooling: Thermal cooling device implementation for devices using
+ *                  devfreq
+ *
+ * Copyright (C) 2014-2015 ARM Limited
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed "as is" WITHOUT ANY WARRANTY of any
+ * kind, whether express or implied; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef __DEVFREQ_COOLING_H__
+#define __DEVFREQ_COOLING_H__
+
+#include <linux/devfreq.h>
+#include <linux/thermal.h>
+
+#ifdef CONFIG_DEVFREQ_THERMAL
+
+/**
+ * struct devfreq_cooling_power - Devfreq cooling power ops
+ * @get_static_power:	Take voltage, in mV, and return the static power
+ *			in mW.  If NULL, the static power is assumed
+ *			to be 0.
+ * @get_dynamic_power:	Take voltage, in mV, and frequency, in HZ, and
+ *			return the dynamic power draw in mW.  If NULL,
+ *			a simple power model is used.
+ * @dyn_power_coeff:	Coefficient for the simple dynamic power model in
+ *			mW/(MHz mV mV).
+ *			If get_dynamic_power() is NULL, then the
+ *			dynamic power is calculated as
+ *			@dyn_power_coeff * frequency * voltage^2
+ */
+struct devfreq_cooling_power {
+	unsigned long (*get_static_power)(unsigned long voltage);
+	unsigned long (*get_dynamic_power)(unsigned long freq,
+					   unsigned long voltage);
+	unsigned long dyn_power_coeff;
+};
+
+struct thermal_cooling_device *
+of_devfreq_cooling_register_power(struct device_node *np, struct devfreq *df,
+				  struct devfreq_cooling_power *dfc_power);
+struct thermal_cooling_device *
+of_devfreq_cooling_register(struct device_node *np, struct devfreq *df);
+struct thermal_cooling_device *devfreq_cooling_register(struct devfreq *df);
+void devfreq_cooling_unregister(struct thermal_cooling_device *dfc);
+
+#else /* !CONFIG_DEVFREQ_THERMAL */
+
+struct thermal_cooling_device *
+of_devfreq_cooling_register_power(struct device_node *np, struct devfreq *df,
+				  struct devfreq_cooling_power *dfc_power)
+{
+	return ERR_PTR(-EINVAL);
+}
+
+static inline struct thermal_cooling_device *
+of_devfreq_cooling_register(struct device_node *np, struct devfreq *df)
+{
+	return ERR_PTR(-EINVAL);
+}
+
+static inline struct thermal_cooling_device *
+devfreq_cooling_register(struct devfreq *df)
+{
+	return ERR_PTR(-EINVAL);
+}
+
+static inline void
+devfreq_cooling_unregister(struct thermal_cooling_device *dfc)
+{
+}
+
+#endif /* CONFIG_DEVFREQ_THERMAL */
+#endif /* __DEVFREQ_COOLING_H__ */

include/trace/events/thermal.h

@@ -4,6 +4,7 @@
 #if !defined(_TRACE_THERMAL_H) || defined(TRACE_HEADER_MULTI_READ)
 #define _TRACE_THERMAL_H
 
+#include <linux/devfreq.h>
 #include <linux/thermal.h>
 #include <linux/tracepoint.h>
 
@@ -135,6 +136,58 @@ TRACE_EVENT(thermal_power_cpu_limit,
 		__entry->power)
 );
 
+TRACE_EVENT(thermal_power_devfreq_get_power,
+	TP_PROTO(struct thermal_cooling_device *cdev,
+		 struct devfreq_dev_status *status, unsigned long freq,
+		u32 dynamic_power, u32 static_power),
+
+	TP_ARGS(cdev, status,  freq, dynamic_power, static_power),
+
+	TP_STRUCT__entry(
+		__string(type,         cdev->type    )
+		__field(unsigned long, freq          )
+		__field(u32,           load          )
+		__field(u32,           dynamic_power )
+		__field(u32,           static_power  )
+	),
+
+	TP_fast_assign(
+		__assign_str(type, cdev->type);
+		__entry->freq = freq;
+		__entry->load = (100 * status->busy_time) / status->total_time;
+		__entry->dynamic_power = dynamic_power;
+		__entry->static_power = static_power;
+	),
+
+	TP_printk("type=%s freq=%lu load=%u dynamic_power=%u static_power=%u",
+		__get_str(type), __entry->freq,
+		__entry->load, __entry->dynamic_power, __entry->static_power)
+);
+
+TRACE_EVENT(thermal_power_devfreq_limit,
+	TP_PROTO(struct thermal_cooling_device *cdev, unsigned long freq,
+		unsigned long cdev_state, u32 power),
+
+	TP_ARGS(cdev, freq, cdev_state, power),
+
+	TP_STRUCT__entry(
+		__string(type,         cdev->type)
+		__field(unsigned int,  freq      )
+		__field(unsigned long, cdev_state)
+		__field(u32,           power     )
+	),
+
+	TP_fast_assign(
+		__assign_str(type, cdev->type);
+		__entry->freq = freq;
+		__entry->cdev_state = cdev_state;
+		__entry->power = power;
+	),
+
+	TP_printk("type=%s freq=%u cdev_state=%lu power=%u",
+		__get_str(type), __entry->freq, __entry->cdev_state,
+		__entry->power)
+);
 #endif /* _TRACE_THERMAL_H */
 
 /* This part must be outside protection */