Commit 7c86f20d authored by Martin Blumenstingl's avatar Martin Blumenstingl Committed by David S. Miller

net: stmmac: use GPIO descriptors in stmmac_mdio_reset

Switch stmmac_mdio_reset to use GPIO descriptors. GPIO core handles the
"snps,reset-gpio" for GPIO descriptors so we don't need to take care of
it inside the driver anymore.

The advantage of this is that we now preserve the GPIO flags which are
passed via devicetree. This is required on some newer Amlogic boards
which use an Open Drain pin for the reset GPIO. This pin can only output
a LOW signal or switch to input mode but it cannot output a HIGH signal.
There are already devicetree bindings for these special cases and GPIO
core already takes care of them but only if we use GPIO descriptors
instead of GPIO numbers.
Signed-off-by: default avatarMartin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: default avatarLinus Walleij <linus.walleij@linaro.org>
Reviewed-by: default avatarAndrew Lunn <andrew@lunn.ch>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
parent 4373a5e2
......@@ -20,11 +20,11 @@
Maintainer: Giuseppe Cavallaro <peppe.cavallaro@st.com>
*******************************************************************************/
#include <linux/gpio/consumer.h>
#include <linux/io.h>
#include <linux/iopoll.h>
#include <linux/mii.h>
#include <linux/of.h>
#include <linux/of_gpio.h>
#include <linux/of_mdio.h>
#include <linux/phy.h>
#include <linux/slab.h>
......@@ -251,37 +251,36 @@ int stmmac_mdio_reset(struct mii_bus *bus)
#ifdef CONFIG_OF
if (priv->device->of_node) {
struct gpio_desc *reset_gpio;
if (data->reset_gpio < 0) {
struct device_node *np = priv->device->of_node;
if (!np)
return 0;
data->reset_gpio = of_get_named_gpio(np,
"snps,reset-gpio", 0);
if (data->reset_gpio < 0)
return 0;
reset_gpio = devm_gpiod_get_optional(priv->device,
"snps,reset",
GPIOD_OUT_LOW);
if (IS_ERR(reset_gpio))
return PTR_ERR(reset_gpio);
data->active_low = of_property_read_bool(np,
"snps,reset-active-low");
of_property_read_u32_array(np,
"snps,reset-delays-us", data->delays, 3);
} else {
reset_gpio = gpio_to_desc(data->reset_gpio);
if (devm_gpio_request(priv->device, data->reset_gpio,
"mdio-reset"))
return 0;
gpiod_direction_output(reset_gpio, 0);
}
gpio_direction_output(data->reset_gpio,
data->active_low ? 1 : 0);
if (data->delays[0])
msleep(DIV_ROUND_UP(data->delays[0], 1000));
gpio_set_value(data->reset_gpio, data->active_low ? 0 : 1);
gpiod_set_value_cansleep(reset_gpio, 1);
if (data->delays[1])
msleep(DIV_ROUND_UP(data->delays[1], 1000));
gpio_set_value(data->reset_gpio, data->active_low ? 1 : 0);
gpiod_set_value_cansleep(reset_gpio, 0);
if (data->delays[2])
msleep(DIV_ROUND_UP(data->delays[2], 1000));
}
......
......@@ -97,7 +97,7 @@ struct stmmac_mdio_bus_data {
int *irqs;
int probed_phy_irq;
#ifdef CONFIG_OF
int reset_gpio, active_low;
int reset_gpio;
u32 delays[3];
#endif
};
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment