e1000e: do not ignore variables which get set a value

Static analysis with cppcheck has shown a few instances of a variable which
is assigned a value that is never used.  A number of these are the return
status of various driver function calls which should be passed back to the
caller of the current function.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

drivers/net/ethernet/intel/e1000e/80003es2lan.c

@@ -773,6 +773,9 @@ static s32 e1000_reset_hw_80003es2lan(struct e1000_hw *hw)
 	ctrl = er32(CTRL);
 
 	ret_val = e1000_acquire_phy_80003es2lan(hw);
+	if (ret_val)
+		return ret_val;
+
 	e_dbg("Issuing a global reset to MAC\n");
 	ew32(CTRL, ctrl | E1000_CTRL_RST);
 	e1000_release_phy_80003es2lan(hw);
@@ -832,6 +835,8 @@ static s32 e1000_init_hw_80003es2lan(struct e1000_hw *hw)
 
 	/* Setup link and flow control */
 	ret_val = mac->ops.setup_link(hw);
+	if (ret_val)
+		return ret_val;
 
 	/* Disable IBIST slave mode (far-end loopback) */
 	e1000_read_kmrn_reg_80003es2lan(hw, E1000_KMRNCTRLSTA_INBAND_PARAM,

drivers/net/ethernet/intel/e1000e/82571.c

@@ -554,16 +554,14 @@ static s32 e1000_get_hw_semaphore_82573(struct e1000_hw *hw)
 	s32 i = 0;
 
 	extcnf_ctrl = er32(EXTCNF_CTRL);
-	extcnf_ctrl |= E1000_EXTCNF_CTRL_MDIO_SW_OWNERSHIP;
 	do {
+		extcnf_ctrl |= E1000_EXTCNF_CTRL_MDIO_SW_OWNERSHIP;
 		ew32(EXTCNF_CTRL, extcnf_ctrl);
 		extcnf_ctrl = er32(EXTCNF_CTRL);
 
 		if (extcnf_ctrl & E1000_EXTCNF_CTRL_MDIO_SW_OWNERSHIP)
 			break;
 
-		extcnf_ctrl |= E1000_EXTCNF_CTRL_MDIO_SW_OWNERSHIP;
-
 		usleep_range(2000, 4000);
 		i++;
 	} while (i < MDIO_OWNERSHIP_TIMEOUT);
@@ -935,6 +933,8 @@ static s32 e1000_set_d0_lplu_state_82571(struct e1000_hw *hw, bool active)
 
 		/* When LPLU is enabled, we should disable SmartSpeed */
 		ret_val = e1e_rphy(hw, IGP01E1000_PHY_PORT_CONFIG, &data);
+		if (ret_val)
+			return ret_val;
 		data &= ~IGP01E1000_PSCFR_SMART_SPEED;
 		ret_val = e1e_wphy(hw, IGP01E1000_PHY_PORT_CONFIG, data);
 		if (ret_val)
@@ -1797,6 +1797,8 @@ static s32 e1000_fix_nvm_checksum_82571(struct e1000_hw *hw)
 			if (ret_val)
 				return ret_val;
 			ret_val = e1000e_update_nvm_checksum(hw);
+			if (ret_val)
+				return ret_val;
 		}
 	}
 

drivers/net/ethernet/intel/e1000e/ich8lan.c

@@ -2342,6 +2342,8 @@ static s32 e1000_set_d0_lplu_state_ich8lan(struct e1000_hw *hw, bool active)
 
 		/* When LPLU is enabled, we should disable SmartSpeed */
 		ret_val = e1e_rphy(hw, IGP01E1000_PHY_PORT_CONFIG, &data);
+		if (ret_val)
+			return ret_val;
 		data &= ~IGP01E1000_PSCFR_SMART_SPEED;
 		ret_val = e1e_wphy(hw, IGP01E1000_PHY_PORT_CONFIG, data);
 		if (ret_val)
@@ -4053,8 +4055,7 @@ void e1000e_gig_downshift_workaround_ich8lan(struct e1000_hw *hw)
 	if (ret_val)
 		return;
 	reg_data &= ~E1000_KMRNCTRLSTA_DIAG_NELPBK;
-	ret_val = e1000e_write_kmrn_reg(hw, E1000_KMRNCTRLSTA_DIAG_OFFSET,
-				       reg_data);
+	e1000e_write_kmrn_reg(hw, E1000_KMRNCTRLSTA_DIAG_OFFSET, reg_data);
 }
 
 /**

drivers/net/ethernet/intel/e1000e/phy.c

@@ -3332,7 +3332,7 @@ s32 e1000_get_cable_length_82577(struct e1000_hw *hw)
 	         I82577_DSTATUS_CABLE_LENGTH_SHIFT;
 
 	if (length == E1000_CABLE_LENGTH_UNDEFINED)
-		ret_val = -E1000_ERR_PHY;
+		return -E1000_ERR_PHY;
 
 	phy->cable_length = length;