net: phy: aquantia: Add some additional phy interfaces

These are documented in the AQR115 register reference. I haven't tested
them, but perhaps they'll be useful to someone.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/phy/aquantia_main.c

@@ -27,9 +27,12 @@
 #define MDIO_PHYXS_VEND_IF_STATUS		0xe812
 #define MDIO_PHYXS_VEND_IF_STATUS_TYPE_MASK	GENMASK(7, 3)
 #define MDIO_PHYXS_VEND_IF_STATUS_TYPE_KR	0
+#define MDIO_PHYXS_VEND_IF_STATUS_TYPE_KX	1
 #define MDIO_PHYXS_VEND_IF_STATUS_TYPE_XFI	2
 #define MDIO_PHYXS_VEND_IF_STATUS_TYPE_USXGMII	3
+#define MDIO_PHYXS_VEND_IF_STATUS_TYPE_XAUI	4
 #define MDIO_PHYXS_VEND_IF_STATUS_TYPE_SGMII	6
+#define MDIO_PHYXS_VEND_IF_STATUS_TYPE_RXAUI	7
 #define MDIO_PHYXS_VEND_IF_STATUS_TYPE_OCSGMII	10
 
 #define MDIO_AN_VEND_PROV			0xc400
@@ -401,15 +404,24 @@ static int aqr107_read_status(struct phy_device *phydev)
 	case MDIO_PHYXS_VEND_IF_STATUS_TYPE_KR:
 		phydev->interface = PHY_INTERFACE_MODE_10GKR;
 		break;
+	case MDIO_PHYXS_VEND_IF_STATUS_TYPE_KX:
+		phydev->interface = PHY_INTERFACE_MODE_1000BASEKX;
+		break;
 	case MDIO_PHYXS_VEND_IF_STATUS_TYPE_XFI:
 		phydev->interface = PHY_INTERFACE_MODE_10GBASER;
 		break;
 	case MDIO_PHYXS_VEND_IF_STATUS_TYPE_USXGMII:
 		phydev->interface = PHY_INTERFACE_MODE_USXGMII;
 		break;
+	case MDIO_PHYXS_VEND_IF_STATUS_TYPE_XAUI:
+		phydev->interface = PHY_INTERFACE_MODE_XAUI;
+		break;
 	case MDIO_PHYXS_VEND_IF_STATUS_TYPE_SGMII:
 		phydev->interface = PHY_INTERFACE_MODE_SGMII;
 		break;
+	case MDIO_PHYXS_VEND_IF_STATUS_TYPE_RXAUI:
+		phydev->interface = PHY_INTERFACE_MODE_RXAUI;
+		break;
 	case MDIO_PHYXS_VEND_IF_STATUS_TYPE_OCSGMII:
 		phydev->interface = PHY_INTERFACE_MODE_2500BASEX;
 		break;
@@ -522,11 +534,14 @@ static int aqr107_config_init(struct phy_device *phydev)
 
 	/* Check that the PHY interface type is compatible */
 	if (phydev->interface != PHY_INTERFACE_MODE_SGMII &&
+	    phydev->interface != PHY_INTERFACE_MODE_1000BASEKX &&
 	    phydev->interface != PHY_INTERFACE_MODE_2500BASEX &&
 	    phydev->interface != PHY_INTERFACE_MODE_XGMII &&
 	    phydev->interface != PHY_INTERFACE_MODE_USXGMII &&
 	    phydev->interface != PHY_INTERFACE_MODE_10GKR &&
-	    phydev->interface != PHY_INTERFACE_MODE_10GBASER)
+	    phydev->interface != PHY_INTERFACE_MODE_10GBASER &&
+	    phydev->interface != PHY_INTERFACE_MODE_XAUI &&
+	    phydev->interface != PHY_INTERFACE_MODE_RXAUI)
 		return -ENODEV;
 
 	WARN(phydev->interface == PHY_INTERFACE_MODE_XGMII,