arm64: dts: imx8mn: Add CPU thermal zone support

i.MX8MN shares same thermal sensor with i.MX8MM, add thermal zone
support for i.MX8MN.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

arch/arm64/boot/dts/freescale/imx8mn.dtsi

@@ -7,6 +7,7 @@
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/input/input.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/thermal/thermal.h>
 
 #include "imx8mn-pinfunc.h"
 
@@ -67,6 +68,7 @@ A53_0: cpu@0 {
 			nvmem-cells = <&cpu_speed_grade>;
 			nvmem-cell-names = "speed_grade";
 			cpu-idle-states = <&cpu_pd_wait>;
+			#cooling-cells = <2>;
 		};
 
 		A53_1: cpu@1 {
@@ -79,6 +81,7 @@ A53_1: cpu@1 {
 			next-level-cache = <&A53_L2>;
 			operating-points-v2 = <&a53_opp_table>;
 			cpu-idle-states = <&cpu_pd_wait>;
+			#cooling-cells = <2>;
 		};
 
 		A53_2: cpu@2 {
@@ -91,6 +94,7 @@ A53_2: cpu@2 {
 			next-level-cache = <&A53_L2>;
 			operating-points-v2 = <&a53_opp_table>;
 			cpu-idle-states = <&cpu_pd_wait>;
+			#cooling-cells = <2>;
 		};
 
 		A53_3: cpu@3 {
@@ -103,6 +107,7 @@ A53_3: cpu@3 {
 			next-level-cache = <&A53_L2>;
 			operating-points-v2 = <&a53_opp_table>;
 			cpu-idle-states = <&cpu_pd_wait>;
+			#cooling-cells = <2>;
 		};
 
 		A53_L2: l2-cache0 {
@@ -186,6 +191,38 @@ psci {
 		method = "smc";
 	};
 
+	thermal-zones {
+		cpu-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <2000>;
+			thermal-sensors = <&tmu>;
+			trips {
+				cpu_alert0: trip0 {
+					temperature = <85000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+
+				cpu_crit0: trip1 {
+					temperature = <95000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+
+			cooling-maps {
+				map0 {
+					trip = <&cpu_alert0>;
+					cooling-device =
+						<&A53_0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+						<&A53_1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+						<&A53_2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+						<&A53_3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+			};
+		};
+	};
+
 	timer {
 		compatible = "arm,armv8-timer";
 		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(6) | IRQ_TYPE_LEVEL_LOW)>,
@@ -274,6 +311,13 @@ gpio5: gpio@30240000 {
 				gpio-ranges = <&iomuxc 0 119 30>;
 			};
 
+			tmu: tmu@30260000 {
+				compatible = "fsl,imx8mn-tmu", "fsl,imx8mm-tmu";
+				reg = <0x30260000 0x10000>;
+				clocks = <&clk IMX8MN_CLK_TMU_ROOT>;
+				#thermal-sensor-cells = <0>;
+			};
+
 			wdog1: watchdog@30280000 {
 				compatible = "fsl,imx8mn-wdt", "fsl,imx21-wdt";
 				reg = <0x30280000 0x10000>;