Commit 81b39802 authored by Anton Vorontsov's avatar Anton Vorontsov Committed by Linus Torvalds

sdhci-of: fix high-speed cards recognition

eSDHC fails to recognize some SDHS cards, throwing timeout errors:

  mmc0: error -110 whilst initialising SD card

That's because we calculate timeout value in a wrong way: on eSDHC hosts
the timeout clock is derivied from the SD clock, which is set dynamically.

As David Vrabel suggested, deriving timeout clock from SD clock is a
common scheme, so let's implement DATA_TIMEOUT_USES_SDCLK quirk and use it
for eSDHC hosts.

Also, from now on we don't need esdhc_get_timeout_clock() callback, so
remove it.
Signed-off-by: default avatarAnton Vorontsov <avorontsov@ru.mvista.com>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: David Vrabel <david.vrabel@csr.com>
Cc: Ben Dooks <ben@fluff.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: default avatarAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: default avatarLinus Torvalds <torvalds@linux-foundation.org>
parent c0859269
......@@ -172,19 +172,13 @@ static unsigned int esdhc_get_min_clock(struct sdhci_host *host)
return of_host->clock / 256 / 16;
}
static unsigned int esdhc_get_timeout_clock(struct sdhci_host *host)
{
struct sdhci_of_host *of_host = sdhci_priv(host);
return of_host->clock / 1000;
}
static struct sdhci_of_data sdhci_esdhc = {
.quirks = SDHCI_QUIRK_FORCE_BLK_SZ_2048 |
SDHCI_QUIRK_BROKEN_CARD_DETECTION |
SDHCI_QUIRK_INVERTED_WRITE_PROTECT |
SDHCI_QUIRK_NO_BUSY_IRQ |
SDHCI_QUIRK_NONSTANDARD_CLOCK |
SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK |
SDHCI_QUIRK_PIO_NEEDS_DELAY |
SDHCI_QUIRK_RESTORE_IRQS_AFTER_RESET |
SDHCI_QUIRK_NO_CARD_NO_RESET,
......@@ -199,7 +193,6 @@ static struct sdhci_of_data sdhci_esdhc = {
.enable_dma = esdhc_enable_dma,
.get_max_clock = esdhc_get_max_clock,
.get_min_clock = esdhc_get_min_clock,
.get_timeout_clock = esdhc_get_timeout_clock,
},
};
......
......@@ -591,6 +591,9 @@ static u8 sdhci_calc_timeout(struct sdhci_host *host, struct mmc_data *data)
target_timeout = data->timeout_ns / 1000 +
data->timeout_clks / host->clock;
if (host->quirks & SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK)
host->timeout_clk = host->clock / 1000;
/*
* Figure out needed cycles.
* We do this in steps in order to fit inside a 32 bit int.
......@@ -1757,13 +1760,15 @@ int sdhci_add_host(struct sdhci_host *host)
host->timeout_clk =
(caps & SDHCI_TIMEOUT_CLK_MASK) >> SDHCI_TIMEOUT_CLK_SHIFT;
if (host->timeout_clk == 0) {
if (!host->ops->get_timeout_clock) {
if (host->ops->get_timeout_clock) {
host->timeout_clk = host->ops->get_timeout_clock(host);
} else if (!(host->quirks &
SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK)) {
printk(KERN_ERR
"%s: Hardware doesn't specify timeout clock "
"frequency.\n", mmc_hostname(mmc));
return -ENODEV;
}
host->timeout_clk = host->ops->get_timeout_clock(host);
}
if (caps & SDHCI_TIMEOUT_CLK_UNIT)
host->timeout_clk *= 1000;
......
......@@ -232,6 +232,8 @@ struct sdhci_host {
#define SDHCI_QUIRK_FORCE_1_BIT_DATA (1<<22)
/* Controller needs 10ms delay between applying power and clock */
#define SDHCI_QUIRK_DELAY_AFTER_POWER (1<<23)
/* Controller uses SDCLK instead of TMCLK for data timeouts */
#define SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK (1<<24)
int irq; /* Device IRQ */
void __iomem * ioaddr; /* Mapped address */
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment