Commit 82e38177 authored by Matthias Fuchs's avatar Matthias Fuchs Committed by David S. Miller

can: Add esd board support to plx_pci CAN driver

This patch adds support for SJA1000 based PCI CAN interface cards
from electronic system design gmbh.

Some changes have been done on the common code:
 - esd boards must not have the 2nd local interupt enabled (PLX9030/9050)
 - a new path for PLX9056/PEX8311 chips has been added
 - new plx9056 reset function has been implemented
 - struct plx_card_info got a reset function entry

In detail the following additional boards are now supported:

        CAN-PCI/200 (PCI)
        CAN-PCI/266 (PCI)
        CAN-PMC266 (PMC module)
        CAN-PCIe/2000 (PCI Express)
        CAN-CPCI/200 (Compact PCI, 3U)
        CAN-PCI104 (PCI104)
Signed-off-by: default avatarMatthias Fuchs <matthias.fuchs@esd.eu>
Acked-by: default avatarWolfgang Grandegger <wg@grandegger.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
parent 2e8e18ef
......@@ -53,7 +53,9 @@ config CAN_PLX_PCI
Driver supports now:
- Adlink PCI-7841/cPCI-7841 card (http://www.adlinktech.com/)
- Adlink PCI-7841/cPCI-7841 SE card
- esd CAN-PCI/CPCI/PCI104/200 (http://www.esd.eu/)
- esd CAN-PCI/PMC/266
- esd CAN-PCIe/2000
- Marathon CAN-bus-PCI card (http://www.marathon.ru/)
- TEWS TECHNOLOGIES TPMC810 card (http://www.tews.com/)
endif
......@@ -41,7 +41,10 @@ MODULE_DESCRIPTION("Socket-CAN driver for PLX90xx PCI-bridge cards with "
MODULE_SUPPORTED_DEVICE("Adlink PCI-7841/cPCI-7841, "
"Adlink PCI-7841/cPCI-7841 SE, "
"Marathon CAN-bus-PCI, "
"TEWS TECHNOLOGIES TPMC810");
"TEWS TECHNOLOGIES TPMC810, "
"esd CAN-PCI/CPCI/PCI104/200, "
"esd CAN-PCI/PMC/266, "
"esd CAN-PCIe/2000")
MODULE_LICENSE("GPL v2");
#define PLX_PCI_MAX_CHAN 2
......@@ -50,11 +53,14 @@ struct plx_pci_card {
int channels; /* detected channels count */
struct net_device *net_dev[PLX_PCI_MAX_CHAN];
void __iomem *conf_addr;
/* Pointer to device-dependent reset function */
void (*reset_func)(struct pci_dev *pdev);
};
#define PLX_PCI_CAN_CLOCK (16000000 / 2)
/* PLX90xx registers */
/* PLX9030/9050/9052 registers */
#define PLX_INTCSR 0x4c /* Interrupt Control/Status */
#define PLX_CNTRL 0x50 /* User I/O, Direct Slave Response,
* Serial EEPROM, and Initialization
......@@ -66,6 +72,14 @@ struct plx_pci_card {
#define PLX_PCI_INT_EN (1 << 6) /* PCI Interrupt Enable */
#define PLX_PCI_RESET (1 << 30) /* PCI Adapter Software Reset */
/* PLX9056 registers */
#define PLX9056_INTCSR 0x68 /* Interrupt Control/Status */
#define PLX9056_CNTRL 0x6c /* Control / Software Reset */
#define PLX9056_LINTI (1 << 11)
#define PLX9056_PCI_INT_EN (1 << 8)
#define PLX9056_PCI_RCR (1 << 29) /* Read Configuration Registers */
/*
* The board configuration is probably following:
* RX1 is connected to ground.
......@@ -101,6 +115,13 @@ struct plx_pci_card {
#define ADLINK_PCI_VENDOR_ID 0x144A
#define ADLINK_PCI_DEVICE_ID 0x7841
#define ESD_PCI_SUB_SYS_ID_PCI200 0x0004
#define ESD_PCI_SUB_SYS_ID_PCI266 0x0009
#define ESD_PCI_SUB_SYS_ID_PMC266 0x000e
#define ESD_PCI_SUB_SYS_ID_CPCI200 0x010b
#define ESD_PCI_SUB_SYS_ID_PCIE2000 0x0200
#define ESD_PCI_SUB_SYS_ID_PCI104200 0x0501
#define MARATHON_PCI_DEVICE_ID 0x2715
#define TEWS_PCI_VENDOR_ID 0x1498
......@@ -108,6 +129,7 @@ struct plx_pci_card {
static void plx_pci_reset_common(struct pci_dev *pdev);
static void plx_pci_reset_marathon(struct pci_dev *pdev);
static void plx9056_pci_reset_common(struct pci_dev *pdev);
struct plx_pci_channel_map {
u32 bar;
......@@ -148,6 +170,30 @@ static struct plx_pci_card_info plx_pci_card_info_adlink_se __devinitdata = {
/* based on PLX9052 */
};
static struct plx_pci_card_info plx_pci_card_info_esd200 __devinitdata = {
"esd CAN-PCI/CPCI/PCI104/200", 2,
PLX_PCI_CAN_CLOCK, PLX_PCI_OCR, PLX_PCI_CDR,
{0, 0x00, 0x00}, { {2, 0x00, 0x80}, {2, 0x100, 0x80} },
&plx_pci_reset_common
/* based on PLX9030/9050 */
};
static struct plx_pci_card_info plx_pci_card_info_esd266 __devinitdata = {
"esd CAN-PCI/PMC/266", 2,
PLX_PCI_CAN_CLOCK, PLX_PCI_OCR, PLX_PCI_CDR,
{0, 0x00, 0x00}, { {2, 0x00, 0x80}, {2, 0x100, 0x80} },
&plx9056_pci_reset_common
/* based on PLX9056 */
};
static struct plx_pci_card_info plx_pci_card_info_esd2000 __devinitdata = {
"esd CAN-PCIe/2000", 2,
PLX_PCI_CAN_CLOCK, PLX_PCI_OCR, PLX_PCI_CDR,
{0, 0x00, 0x00}, { {2, 0x00, 0x80}, {2, 0x100, 0x80} },
&plx9056_pci_reset_common
/* based on PEX8311 */
};
static struct plx_pci_card_info plx_pci_card_info_marathon __devinitdata = {
"Marathon CAN-bus-PCI", 2,
PLX_PCI_CAN_CLOCK, PLX_PCI_OCR, PLX_PCI_CDR,
......@@ -179,6 +225,48 @@ static DEFINE_PCI_DEVICE_TABLE(plx_pci_tbl) = {
PCI_CLASS_COMMUNICATION_OTHER << 8, ~0,
(kernel_ulong_t)&plx_pci_card_info_adlink_se
},
{
/* esd CAN-PCI/200 */
PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9050,
PCI_VENDOR_ID_ESDGMBH, ESD_PCI_SUB_SYS_ID_PCI200,
0, 0,
(kernel_ulong_t)&plx_pci_card_info_esd200
},
{
/* esd CAN-CPCI/200 */
PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9030,
PCI_VENDOR_ID_ESDGMBH, ESD_PCI_SUB_SYS_ID_CPCI200,
0, 0,
(kernel_ulong_t)&plx_pci_card_info_esd200
},
{
/* esd CAN-PCI104/200 */
PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9030,
PCI_VENDOR_ID_ESDGMBH, ESD_PCI_SUB_SYS_ID_PCI104200,
0, 0,
(kernel_ulong_t)&plx_pci_card_info_esd200
},
{
/* esd CAN-PCI/266 */
PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9056,
PCI_VENDOR_ID_ESDGMBH, ESD_PCI_SUB_SYS_ID_PCI266,
0, 0,
(kernel_ulong_t)&plx_pci_card_info_esd266
},
{
/* esd CAN-PMC/266 */
PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9056,
PCI_VENDOR_ID_ESDGMBH, ESD_PCI_SUB_SYS_ID_PMC266,
0, 0,
(kernel_ulong_t)&plx_pci_card_info_esd266
},
{
/* esd CAN-PCIE/2000 */
PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9056,
PCI_VENDOR_ID_ESDGMBH, ESD_PCI_SUB_SYS_ID_PCIE2000,
0, 0,
(kernel_ulong_t)&plx_pci_card_info_esd2000
},
{
/* Marathon CAN-bus-PCI card */
PCI_VENDOR_ID_PLX, MARATHON_PCI_DEVICE_ID,
......@@ -242,7 +330,7 @@ static inline int plx_pci_check_sja1000(const struct sja1000_priv *priv)
}
/*
* PLX90xx software reset
* PLX9030/50/52 software reset
* Also LRESET# asserts and brings to reset device on the Local Bus (if wired).
* For most cards it's enough for reset the SJA1000 chips.
*/
......@@ -259,6 +347,38 @@ static void plx_pci_reset_common(struct pci_dev *pdev)
iowrite32(cntrl, card->conf_addr + PLX_CNTRL);
};
/*
* PLX9056 software reset
* Assert LRESET# and reset device(s) on the Local Bus (if wired).
*/
static void plx9056_pci_reset_common(struct pci_dev *pdev)
{
struct plx_pci_card *card = pci_get_drvdata(pdev);
u32 cntrl;
/* issue a local bus reset */
cntrl = ioread32(card->conf_addr + PLX9056_CNTRL);
cntrl |= PLX_PCI_RESET;
iowrite32(cntrl, card->conf_addr + PLX9056_CNTRL);
udelay(100);
cntrl ^= PLX_PCI_RESET;
iowrite32(cntrl, card->conf_addr + PLX9056_CNTRL);
/* reload local configuration from EEPROM */
cntrl |= PLX9056_PCI_RCR;
iowrite32(cntrl, card->conf_addr + PLX9056_CNTRL);
/*
* There is no safe way to poll for the end
* of reconfiguration process. Waiting for 10ms
* is safe.
*/
mdelay(10);
cntrl ^= PLX9056_PCI_RCR;
iowrite32(cntrl, card->conf_addr + PLX9056_CNTRL);
};
/* Special reset function for Marathon card */
static void plx_pci_reset_marathon(struct pci_dev *pdev)
{
......@@ -302,13 +422,16 @@ static void plx_pci_del_card(struct pci_dev *pdev)
free_sja1000dev(dev);
}
plx_pci_reset_common(pdev);
card->reset_func(pdev);
/*
* Disable interrupts from PCI-card (PLX90xx) and disable Local_1,
* Local_2 interrupts
* Disable interrupts from PCI-card and disable local
* interrupts
*/
iowrite32(0x0, card->conf_addr + PLX_INTCSR);
if (pdev->device != PCI_DEVICE_ID_PLX_9056)
iowrite32(0x0, card->conf_addr + PLX_INTCSR);
else
iowrite32(0x0, card->conf_addr + PLX9056_INTCSR);
if (card->conf_addr)
pci_iounmap(pdev, card->conf_addr);
......@@ -367,6 +490,7 @@ static int __devinit plx_pci_add_card(struct pci_dev *pdev,
card->conf_addr = addr + ci->conf_map.offset;
ci->reset_func(pdev);
card->reset_func = ci->reset_func;
/* Detect available channels */
for (i = 0; i < ci->channel_count; i++) {
......@@ -438,10 +562,17 @@ static int __devinit plx_pci_add_card(struct pci_dev *pdev,
* Enable interrupts from PCI-card (PLX90xx) and enable Local_1,
* Local_2 interrupts from the SJA1000 chips
*/
val = ioread32(card->conf_addr + PLX_INTCSR);
val |= PLX_LINT1_EN | PLX_LINT2_EN | PLX_PCI_INT_EN;
iowrite32(val, card->conf_addr + PLX_INTCSR);
if (pdev->device != PCI_DEVICE_ID_PLX_9056) {
val = ioread32(card->conf_addr + PLX_INTCSR);
if (pdev->subsystem_vendor == PCI_VENDOR_ID_ESDGMBH)
val |= PLX_LINT1_EN | PLX_PCI_INT_EN;
else
val |= PLX_LINT1_EN | PLX_LINT2_EN | PLX_PCI_INT_EN;
iowrite32(val, card->conf_addr + PLX_INTCSR);
} else {
iowrite32(PLX9056_LINTI | PLX9056_PCI_INT_EN,
card->conf_addr + PLX9056_INTCSR);
}
return 0;
failure_cleanup:
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment