Commit 83ef106f authored by Viken Dadhaniya's avatar Viken Dadhaniya Committed by Andi Shyti

i2c: qcom-geni: Correct I2C TRE sequence

For i2c read operation in GSI mode, we are getting timeout
due to malformed TRE basically incorrect TRE sequence
in gpi(drivers/dma/qcom/gpi.c) driver.

I2C driver has geni_i2c_gpi(I2C_WRITE) function which generates GO TRE and
geni_i2c_gpi(I2C_READ)generates DMA TRE. Hence to generate GO TRE before
DMA TRE, we should move geni_i2c_gpi(I2C_WRITE) before
geni_i2c_gpi(I2C_READ) inside the I2C GSI mode transfer function
i.e. geni_i2c_gpi_xfer().

TRE stands for Transfer Ring Element - which is basically an element with
size of 4 words. It contains all information like slave address,
clk divider, dma address value data size etc).

Mainly we have 3 TREs(Config, GO and DMA tre).
- CONFIG TRE : consists of internal register configuration which is
               required before start of the transfer.
- DMA TRE :    contains DDR/Memory address, called as DMA descriptor.
- GO TRE :     contains Transfer directions, slave ID, Delay flags, Length
               of the transfer.

I2c driver calls GPI driver API to config each TRE depending on the
protocol.

For read operation tre sequence will be as below which is not aligned
to hardware programming guide.

- CONFIG tre
- DMA tre
- GO tre

As per Qualcomm's internal Hardware Programming Guide, we should configure
TREs in below sequence for any RX only transfer.

- CONFIG tre
- GO tre
- DMA tre

Fixes: d8703554 ("i2c: qcom-geni: Add support for GPI DMA")
Reviewed-by: default avatarAndi Shyti <andi.shyti@kernel.org>
Reviewed-by: default avatarBryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> # qrb5165-rb5
Co-developed-by: default avatarMukesh Kumar Savaliya <quic_msavaliy@quicinc.com>
Signed-off-by: default avatarMukesh Kumar Savaliya <quic_msavaliy@quicinc.com>
Signed-off-by: default avatarViken Dadhaniya <quic_vdadhani@quicinc.com>
Reviewed-by: default avatarDmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: default avatarAndi Shyti <andi.shyti@kernel.org>
parent 54be6c6c
......@@ -613,20 +613,20 @@ static int geni_i2c_gpi_xfer(struct geni_i2c_dev *gi2c, struct i2c_msg msgs[], i
peripheral.addr = msgs[i].addr;
ret = geni_i2c_gpi(gi2c, &msgs[i], &config,
&tx_addr, &tx_buf, I2C_WRITE, gi2c->tx_c);
if (ret)
goto err;
if (msgs[i].flags & I2C_M_RD) {
ret = geni_i2c_gpi(gi2c, &msgs[i], &config,
&rx_addr, &rx_buf, I2C_READ, gi2c->rx_c);
if (ret)
goto err;
}
ret = geni_i2c_gpi(gi2c, &msgs[i], &config,
&tx_addr, &tx_buf, I2C_WRITE, gi2c->tx_c);
if (ret)
goto err;
if (msgs[i].flags & I2C_M_RD)
dma_async_issue_pending(gi2c->rx_c);
}
dma_async_issue_pending(gi2c->tx_c);
timeout = wait_for_completion_timeout(&gi2c->done, XFER_TIMEOUT);
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment