USB: ehci-platform: check for platform data misconfiguration

The ehci-platform driver checks for misconfigurations in cases where
the Device Tree data specifies big-endian registers or descriptors but
the corresponding driver config settings have not been enabled.  As
Jonas Gorski suggested, we may as well apply the same check to general
platform data too.

This requires moving the code that sets the big-endian quirk flags
from the ehci_platform_reset() routine into ehci_platform_probe(), and
moving the checks out of the DT-specific "if" statement clause.

The patch also changes the text of the error messages in an attempt to
make the nature of the error more clear.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Jonas Gorski <jogo@openwrt.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drivers/usb/host/ehci-platform.c

@@ -55,10 +55,6 @@ static int ehci_platform_reset(struct usb_hcd *hcd)
 
 	hcd->has_tt = pdata->has_tt;
 	ehci->has_synopsys_hc_bug = pdata->has_synopsys_hc_bug;
-	if (pdata->big_endian_desc)
-		ehci->big_endian_desc = 1;
-	if (pdata->big_endian_mmio)
-		ehci->big_endian_mmio = 1;
 
 	if (pdata->pre_setup) {
 		retval = pdata->pre_setup(hcd);
@@ -192,22 +188,6 @@ static int ehci_platform_probe(struct platform_device *dev)
 		if (of_property_read_bool(dev->dev.of_node, "big-endian"))
 			ehci->big_endian_mmio = ehci->big_endian_desc = 1;
 
-#ifndef CONFIG_USB_EHCI_BIG_ENDIAN_MMIO
-		if (ehci->big_endian_mmio) {
-			dev_err(&dev->dev,
-				"Error big-endian-regs not compiled in\n");
-			err = -EINVAL;
-			goto err_put_hcd;
-		}
-#endif
-#ifndef CONFIG_USB_EHCI_BIG_ENDIAN_DESC
-		if (ehci->big_endian_desc) {
-			dev_err(&dev->dev,
-				"Error big-endian-desc not compiled in\n");
-			err = -EINVAL;
-			goto err_put_hcd;
-		}
-#endif
 		priv->phy = devm_phy_get(&dev->dev, "usb");
 		if (IS_ERR(priv->phy)) {
 			err = PTR_ERR(priv->phy);
@@ -228,6 +208,28 @@ static int ehci_platform_probe(struct platform_device *dev)
 		}
 	}
 
+	if (pdata->big_endian_desc)
+		ehci->big_endian_desc = 1;
+	if (pdata->big_endian_mmio)
+		ehci->big_endian_mmio = 1;
+
+#ifndef CONFIG_USB_EHCI_BIG_ENDIAN_MMIO
+	if (ehci->big_endian_mmio) {
+		dev_err(&dev->dev,
+			"Error: CONFIG_USB_EHCI_BIG_ENDIAN_MMIO not set\n");
+		err = -EINVAL;
+		goto err_put_clks;
+	}
+#endif
+#ifndef CONFIG_USB_EHCI_BIG_ENDIAN_DESC
+	if (ehci->big_endian_desc) {
+		dev_err(&dev->dev,
+			"Error: CONFIG_USB_EHCI_BIG_ENDIAN_DESC not set\n");
+		err = -EINVAL;
+		goto err_put_clks;
+	}
+#endif
+
 	if (pdata->power_on) {
 		err = pdata->power_on(dev);
 		if (err < 0)