Commit 8533966a authored by Maciej W. Rozycki's avatar Maciej W. Rozycki Committed by Ralf Baechle

MIPS: DECstation HRT calibration bug fixes

This change corrects DECstation HRT calibration, by removing the following
bugs:

1. Calibration period selection -- HZ / 10 has been chosen, however on
   DECstation computers, HZ never divides by 10, as the choice for HZ is
   among 128, 256 and 1024.  The choice therefore results in a systematic
   calibration error, e.g. 6.25% for the usual choice of 128 for HZ:

   128 / 10 * 10 = 120

   (128 - 120) / 128 -> 6.25%

   The change therefore makes calibration use HZ / 8 that is always
   accurate for the HZ values available, getting rid of the systematic
   error.

2. Calibration starting point synchronisation -- the duration of a number
   of intervals between DS1287A periodic interrupt assertions is measured,
   however code does not ensure at the beginning that the interrupt has
   not been previously asserted.  This results in a variable error of e.g.
   up to another 6.25% for the period of HZ / 8 (8.(3)% with the original
   HZ / 10 period) and the usual choice of 128 for HZ:

   1 / 16 -> 6.25%

   1 / 12 -> 8.(3)%

   The change therefore adds an initial call to ds1287_timer_state that
   clears any previous periodic interrupt pending.

The same issue applies to both I/O ASIC counter and R4k CP0 timer
calibration on DECstation systems as similar code is used in both cases
and both pieces of code are covered by this fix.

On an R3400 test system used this fix results in a change of the I/O ASIC
clock frequency reported from values like:

I/O ASIC clock frequency 23185830Hz

to:

I/O ASIC clock frequency 24999288Hz

removing the miscalculation by 6.25% from the systematic error and (for
the individual sample provided) a further 1.00% from the variable error,
accordingly.  The nominal I/O ASIC clock frequency is 25MHz on this
system.

Here's another result, with the fix applied, from a system that has both
HRTs available (using an R4400 at 60MHz nominal):

MIPS counter frequency 59999328Hz
I/O ASIC clock frequency 24999432Hz
Signed-off-by: default avatarMaciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5807/Signed-off-by: default avatarRalf Baechle <ralf@linux-mips.org>
parent bf9621aa
......@@ -126,12 +126,13 @@ int rtc_mips_set_mmss(unsigned long nowtime)
void __init plat_time_init(void)
{
u32 start, end;
int i = HZ / 10;
int i = HZ / 8;
/* Set up the rate of periodic DS1287 interrupts. */
ds1287_set_base_clock(HZ);
if (cpu_has_counter) {
ds1287_timer_state();
while (!ds1287_timer_state())
;
......@@ -143,7 +144,7 @@ void __init plat_time_init(void)
end = read_c0_count();
mips_hpt_frequency = (end - start) * 10;
mips_hpt_frequency = (end - start) * 8;
printk(KERN_INFO "MIPS counter frequency %dHz\n",
mips_hpt_frequency);
} else if (IOASIC)
......
......@@ -41,9 +41,9 @@ void __init dec_ioasic_clocksource_init(void)
{
unsigned int freq;
u32 start, end;
int i = HZ / 10;
int i = HZ / 8;
ds1287_timer_state();
while (!ds1287_timer_state())
;
......@@ -55,7 +55,7 @@ void __init dec_ioasic_clocksource_init(void)
end = dec_ioasic_hpt_read(&clocksource_dec);
freq = (end - start) * 10;
freq = (end - start) * 8;
printk(KERN_INFO "I/O ASIC clock frequency %dHz\n", freq);
clocksource_dec.rating = 200 + freq / 10000000;
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment