ARM: dts: rename MSM8660/APQ8060 pmicintc to pm8058

The name "pmicintc" is ambiguous: there is a second power
management IC named PM8901 on these systems, and it is also
an interrupt controller. To make things clear, just name the
node alias "pm8058", this in unambigous and has all information
we need.
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>

arch/arm/boot/dts/qcom-apq8060-dragonboard.dts

@@ -412,7 +412,7 @@ ethernet-ebi2@2,0 {
 				 * The second interrupt is the PME interrupt
 				 * for network wakeup, connected to the TLMM.
 				 */
-				interrupts-extended = <&pmicintc 198 IRQ_TYPE_EDGE_FALLING>,
+				interrupts-extended = <&pm8058 198 IRQ_TYPE_EDGE_FALLING>,
 						    <&tlmm 29 IRQ_TYPE_EDGE_RISING>;
 				reset-gpios = <&tlmm 30 GPIO_ACTIVE_LOW>;
 				vdd33a-supply = <&dragon_veth>;

arch/arm/boot/dts/qcom-msm8660-surf.dts

@@ -48,7 +48,7 @@ sdcc3: sdcc@12180000 {
 	};
 };
 
-&pmicintc {
+&pm8058 {
 	keypad@148 {
 		linux,keymap = <
 			MATRIX_KEY(0, 0, KEY_FN_F1)

arch/arm/boot/dts/qcom-msm8660.dtsi

@@ -163,7 +163,7 @@ qcom,ssbi@500000 {
 			reg = <0x500000 0x1000>;
 			qcom,controller-type = "pmic-arbiter";
 
-			pmicintc: pmic@0 {
+			pm8058: pmic@0 {
 				compatible = "qcom,pm8058";
 				interrupt-parent = <&tlmm>;
 				interrupts = <88 8>;
@@ -176,7 +176,7 @@ pm8058_gpio: gpio@150 {
 					compatible = "qcom,pm8058-gpio",
 						     "qcom,ssbi-gpio";
 					reg = <0x150>;
-					interrupt-parent = <&pmicintc>;
+					interrupt-parent = <&pm8058>;
 					interrupts = <192 IRQ_TYPE_NONE>,
 						     <193 IRQ_TYPE_NONE>,
 						     <194 IRQ_TYPE_NONE>,
@@ -232,7 +232,7 @@ pm8058_mpps: mpps@50 {
 					reg = <0x50>;
 					gpio-controller;
 					#gpio-cells = <2>;
-					interrupt-parent = <&pmicintc>;
+					interrupt-parent = <&pm8058>;
 					interrupts =
 					<128 IRQ_TYPE_NONE>,
 					<129 IRQ_TYPE_NONE>,
@@ -251,7 +251,7 @@ pm8058_mpps: mpps@50 {
 				pwrkey@1c {
 					compatible = "qcom,pm8058-pwrkey";
 					reg = <0x1c>;
-					interrupt-parent = <&pmicintc>;
+					interrupt-parent = <&pm8058>;
 					interrupts = <50 1>, <51 1>;
 					debounce = <15625>;
 					pull-up;
@@ -260,7 +260,7 @@ pwrkey@1c {
 				keypad@148 {
 					compatible = "qcom,pm8058-keypad";
 					reg = <0x148>;
-					interrupt-parent = <&pmicintc>;
+					interrupt-parent = <&pm8058>;
 					interrupts = <74 1>, <75 1>;
 					debounce = <15>;
 					scan-delay = <32>;
@@ -270,7 +270,7 @@ keypad@148 {
 				rtc@1e8 {
 					compatible = "qcom,pm8058-rtc";
 					reg = <0x1e8>;
-					interrupt-parent = <&pmicintc>;
+					interrupt-parent = <&pm8058>;
 					interrupts = <39 1>;
 					allow-set-time;
 				};