Commit 89077c71 authored by Adam Ford's avatar Adam Ford Committed by Tony Lindgren

ARM: dts: Add HSUSB2 EHCI Support to Logic PD DM37xx SOM-LV

The Logic PD SOM-LV has a USB Host Controller connected to 3-port
hub.  This enables the pin muxing for the host controller and
ehci-phy.
Signed-off-by: default avatarAdam Ford <aford173@gmail.com>
Signed-off-by: default avatarTony Lindgren <tony@atomide.com>
parent 8d08394f
......@@ -23,6 +23,12 @@ wl12xx_vmmc: wl12xx_vmmc {
enable-active-high;
vin-supply = <&vmmc2>;
};
/* HS USB Host PHY on PORT 1 */
hsusb2_phy: hsusb2_phy {
compatible = "usb-nop-xceiv";
reset-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>; /* gpio_4 */
};
};
&gpmc {
......@@ -126,7 +132,19 @@ wlcore: wlcore@2 {
};
};
&usbhshost {
port2-mode = "ehci-phy";
};
&usbhsehci {
phys = <0 &hsusb2_phy>;
};
&omap3_pmx_core {
pinctrl-names = "default";
pinctrl-0 = <&hsusb2_pins>;
mmc3_pins: pinmux_mm3_pins {
pinctrl-single,pins = <
OMAP3_CORE1_IOPAD(0x2164, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat4.sdmmc3_dat0 */
......@@ -164,6 +182,18 @@ OMAP3_CORE1_IOPAD(0x21cc, PIN_INPUT_PULLUP | MUX_MODE0) /* mcspi1_somi.mcspi1_so
OMAP3_CORE1_IOPAD(0x21ce, PIN_OUTPUT | MUX_MODE0) /* mcspi1_cs0.mcspi1_cs0 */
>;
};
hsusb2_pins: pinmux_hsusb2_pins {
pinctrl-single,pins = <
OMAP3_CORE1_IOPAD(0x21d4, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi1_cs3.hsusb2_data2 */
OMAP3_CORE1_IOPAD(0x21d6, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_clk.hsusb2_data7 */
OMAP3_CORE1_IOPAD(0x21d8, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_simo.hsusb2_data4 */
OMAP3_CORE1_IOPAD(0x21da, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_somi.hsusb2_data5 */
OMAP3_CORE1_IOPAD(0x21dc, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_cs0.hsusb2_data6 */
OMAP3_CORE1_IOPAD(0x21de, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_cs1.hsusb2_data3 */
>;
};
hsusb_otg_pins: pinmux_hsusb_otg_pins {
pinctrl-single,pins = <
OMAP3_CORE1_IOPAD(0x21a2, PIN_INPUT | MUX_MODE0) /* hsusb0_clk.hsusb0_clk */
......@@ -180,6 +210,33 @@ OMAP3_CORE1_IOPAD(0x21b6, PIN_INPUT | MUX_MODE0) /* hsusb0_data6.hsusb0_data6 */
OMAP3_CORE1_IOPAD(0x21b8, PIN_INPUT | MUX_MODE0) /* hsusb0_data7.hsusb0_data7 */
>;
};
};
&omap3_pmx_wkup {
pinctrl-names = "default";
pinctrl-0 = <&hsusb2_reset_pin>;
hsusb2_reset_pin: pinmux_hsusb1_reset_pin {
pinctrl-single,pins = <
OMAP3_WKUP_IOPAD(0x2a0e, PIN_OUTPUT | MUX_MODE4) /* sys_boot2.gpio_4 */
>;
};
};
&omap3_pmx_core2 {
pinctrl-names = "default";
pinctrl-0 = <&hsusb2_2_pins>;
hsusb2_2_pins: pinmux_hsusb2_2_pins {
pinctrl-single,pins = <
OMAP3630_CORE2_IOPAD(0x25f0, PIN_OUTPUT | MUX_MODE3) /* etk_d10.hsusb2_clk */
OMAP3630_CORE2_IOPAD(0x25f2, PIN_OUTPUT | MUX_MODE3) /* etk_d11.hsusb2_stp */
OMAP3630_CORE2_IOPAD(0x25f4, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d12.hsusb2_dir */
OMAP3630_CORE2_IOPAD(0x25f6, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d13.hsusb2_nxt */
OMAP3630_CORE2_IOPAD(0x25f8, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d14.hsusb2_data0 */
OMAP3630_CORE2_IOPAD(0x25fa, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d15.hsusb2_data1 */
>;
};
};
&uart2 {
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment