Merge tag 'qcom-drivers-for-4.15' of...

Merge tag 'qcom-drivers-for-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux into next/drivers

Pull "Qualcomm ARM Based Driver Updates for v4.15" from Andy Gross:

* Add SCM firmware APIs for download mode and secure IO service
* Add SMEM support for cached entries
* Add SMEM support for global partition, dynamic item limit, and more hosts

* tag 'qcom-drivers-for-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux:
  firmware: qcom: scm: Expose download-mode control
  firmware: qcom: scm: Expose secure IO service
  soc: qcom: smem: Increase the number of hosts
  soc: qcom: smem: Support dynamic item limit
  soc: qcom: smem: Support global partition
  soc: qcom: smem: Read version from the smem header
  soc: qcom: smem: Use le32_to_cpu for comparison
  soc: qcom: smem: Support getting cached entries
  soc: qcom: smem: Rename "uncached" accessors

Documentation/devicetree/bindings/firmware/qcom,scm.txt

@@ -18,6 +18,8 @@ Required properties:
  * Core, iface, and bus clocks required for "qcom,scm"
 - clock-names: Must contain "core" for the core clock, "iface" for the interface
   clock and "bus" for the bus clock per the requirements of the compatible.
+- qcom,dload-mode: phandle to the TCSR hardware block and offset of the
+		   download mode control register (optional)
 
 Example for MSM8916:
 

drivers/firmware/Kconfig

@@ -215,6 +215,17 @@ config QCOM_SCM_64
 	def_bool y
 	depends on QCOM_SCM && ARM64
 
+config QCOM_SCM_DOWNLOAD_MODE_DEFAULT
+	bool "Qualcomm download mode enabled by default"
+	depends on QCOM_SCM
+	help
+	  A device with "download mode" enabled will upon an unexpected
+	  warm-restart enter a special debug mode that allows the user to
+	  "download" memory content over USB for offline postmortem analysis.
+	  The feature can be enabled/disabled on the kernel command line.
+
+	  Say Y here to enable "download mode" by default.
+
 config TI_SCI_PROTOCOL
 	tristate "TI System Control Interface (TISCI) Message Protocol"
 	depends on TI_MESSAGE_MANAGER

drivers/firmware/qcom_scm-32.c

@@ -561,6 +561,12 @@ int __qcom_scm_pas_mss_reset(struct device *dev, bool reset)
 	return ret ? : le32_to_cpu(out);
 }
 
+int __qcom_scm_set_dload_mode(struct device *dev, bool enable)
+{
+	return qcom_scm_call_atomic2(QCOM_SCM_SVC_BOOT, QCOM_SCM_SET_DLOAD_MODE,
+				     enable ? QCOM_SCM_SET_DLOAD_MODE : 0, 0);
+}
+
 int __qcom_scm_set_remote_state(struct device *dev, u32 state, u32 id)
 {
 	struct {
@@ -596,3 +602,21 @@ int __qcom_scm_iommu_secure_ptbl_init(struct device *dev, u64 addr, u32 size,
 {
 	return -ENODEV;
 }
+
+int __qcom_scm_io_readl(struct device *dev, phys_addr_t addr,
+			unsigned int *val)
+{
+	int ret;
+
+	ret = qcom_scm_call_atomic1(QCOM_SCM_SVC_IO, QCOM_SCM_IO_READ, addr);
+	if (ret >= 0)
+		*val = ret;
+
+	return ret < 0 ? ret : 0;
+}
+
+int __qcom_scm_io_writel(struct device *dev, phys_addr_t addr, unsigned int val)
+{
+	return qcom_scm_call_atomic2(QCOM_SCM_SVC_IO, QCOM_SCM_IO_WRITE,
+				     addr, val);
+}

drivers/firmware/qcom_scm-64.c

@@ -439,3 +439,47 @@ int __qcom_scm_iommu_secure_ptbl_init(struct device *dev, u64 addr, u32 size,
 
 	return ret;
 }
+
+int __qcom_scm_set_dload_mode(struct device *dev, bool enable)
+{
+	struct qcom_scm_desc desc = {0};
+	struct arm_smccc_res res;
+
+	desc.args[0] = QCOM_SCM_SET_DLOAD_MODE;
+	desc.args[1] = enable ? QCOM_SCM_SET_DLOAD_MODE : 0;
+	desc.arginfo = QCOM_SCM_ARGS(2);
+
+	return qcom_scm_call(dev, QCOM_SCM_SVC_BOOT, QCOM_SCM_SET_DLOAD_MODE,
+			     &desc, &res);
+}
+
+int __qcom_scm_io_readl(struct device *dev, phys_addr_t addr,
+			unsigned int *val)
+{
+	struct qcom_scm_desc desc = {0};
+	struct arm_smccc_res res;
+	int ret;
+
+	desc.args[0] = addr;
+	desc.arginfo = QCOM_SCM_ARGS(1);
+
+	ret = qcom_scm_call(dev, QCOM_SCM_SVC_IO, QCOM_SCM_IO_READ,
+			    &desc, &res);
+	if (ret >= 0)
+		*val = res.a1;
+
+	return ret < 0 ? ret : 0;
+}
+
+int __qcom_scm_io_writel(struct device *dev, phys_addr_t addr, unsigned int val)
+{
+	struct qcom_scm_desc desc = {0};
+	struct arm_smccc_res res;
+
+	desc.args[0] = addr;
+	desc.args[1] = val;
+	desc.arginfo = QCOM_SCM_ARGS(2);
+
+	return qcom_scm_call(dev, QCOM_SCM_SVC_IO, QCOM_SCM_IO_WRITE,
+			     &desc, &res);
+}

drivers/firmware/qcom_scm.c

@@ -19,15 +19,20 @@
 #include <linux/cpumask.h>
 #include <linux/export.h>
 #include <linux/dma-mapping.h>
+#include <linux/module.h>
 #include <linux/types.h>
 #include <linux/qcom_scm.h>
 #include <linux/of.h>
+#include <linux/of_address.h>
 #include <linux/of_platform.h>
 #include <linux/clk.h>
 #include <linux/reset-controller.h>
 
 #include "qcom_scm.h"
 
+static bool download_mode = IS_ENABLED(CONFIG_QCOM_SCM_DOWNLOAD_MODE_DEFAULT);
+module_param(download_mode, bool, 0);
+
 #define SCM_HAS_CORE_CLK	BIT(0)
 #define SCM_HAS_IFACE_CLK	BIT(1)
 #define SCM_HAS_BUS_CLK		BIT(2)
@@ -38,6 +43,8 @@ struct qcom_scm {
 	struct clk *iface_clk;
 	struct clk *bus_clk;
 	struct reset_controller_dev reset;
+
+	u64 dload_mode_addr;
 };
 
 static struct qcom_scm *__scm;
@@ -333,6 +340,66 @@ int qcom_scm_iommu_secure_ptbl_init(u64 addr, u32 size, u32 spare)
 }
 EXPORT_SYMBOL(qcom_scm_iommu_secure_ptbl_init);
 
+int qcom_scm_io_readl(phys_addr_t addr, unsigned int *val)
+{
+	return __qcom_scm_io_readl(__scm->dev, addr, val);
+}
+EXPORT_SYMBOL(qcom_scm_io_readl);
+
+int qcom_scm_io_writel(phys_addr_t addr, unsigned int val)
+{
+	return __qcom_scm_io_writel(__scm->dev, addr, val);
+}
+EXPORT_SYMBOL(qcom_scm_io_writel);
+
+static void qcom_scm_set_download_mode(bool enable)
+{
+	bool avail;
+	int ret = 0;
+
+	avail = __qcom_scm_is_call_available(__scm->dev,
+					     QCOM_SCM_SVC_BOOT,
+					     QCOM_SCM_SET_DLOAD_MODE);
+	if (avail) {
+		ret = __qcom_scm_set_dload_mode(__scm->dev, enable);
+	} else if (__scm->dload_mode_addr) {
+		ret = __qcom_scm_io_writel(__scm->dev, __scm->dload_mode_addr,
+					   enable ? QCOM_SCM_SET_DLOAD_MODE : 0);
+	} else {
+		dev_err(__scm->dev,
+			"No available mechanism for setting download mode\n");
+	}
+
+	if (ret)
+		dev_err(__scm->dev, "failed to set download mode: %d\n", ret);
+}
+
+static int qcom_scm_find_dload_address(struct device *dev, u64 *addr)
+{
+	struct device_node *tcsr;
+	struct device_node *np = dev->of_node;
+	struct resource res;
+	u32 offset;
+	int ret;
+
+	tcsr = of_parse_phandle(np, "qcom,dload-mode", 0);
+	if (!tcsr)
+		return 0;
+
+	ret = of_address_to_resource(tcsr, 0, &res);
+	of_node_put(tcsr);
+	if (ret)
+		return ret;
+
+	ret = of_property_read_u32_index(np, "qcom,dload-mode", 1, &offset);
+	if (ret < 0)
+		return ret;
+
+	*addr = res.start + offset;
+
+	return 0;
+}
+
 /**
  * qcom_scm_is_available() - Checks if SCM is available
  */
@@ -358,6 +425,10 @@ static int qcom_scm_probe(struct platform_device *pdev)
 	if (!scm)
 		return -ENOMEM;
 
+	ret = qcom_scm_find_dload_address(&pdev->dev, &scm->dload_mode_addr);
+	if (ret < 0)
+		return ret;
+
 	clks = (unsigned long)of_device_get_match_data(&pdev->dev);
 	if (clks & SCM_HAS_CORE_CLK) {
 		scm->core_clk = devm_clk_get(&pdev->dev, "core");
@@ -406,9 +477,24 @@ static int qcom_scm_probe(struct platform_device *pdev)
 
 	__qcom_scm_init();
 
+	/*
+	 * If requested enable "download mode", from this point on warmboot
+	 * will cause the the boot stages to enter download mode, unless
+	 * disabled below by a clean shutdown/reboot.
+	 */
+	if (download_mode)
+		qcom_scm_set_download_mode(true);
+
 	return 0;
 }
 
+static void qcom_scm_shutdown(struct platform_device *pdev)
+{
+	/* Clean shutdown, disable download mode to allow normal restart */
+	if (download_mode)
+		qcom_scm_set_download_mode(false);
+}
+
 static const struct of_device_id qcom_scm_dt_match[] = {
 	{ .compatible = "qcom,scm-apq8064",
 	  /* FIXME: This should have .data = (void *) SCM_HAS_CORE_CLK */
@@ -436,6 +522,7 @@ static struct platform_driver qcom_scm_driver = {
 		.of_match_table = qcom_scm_dt_match,
 	},
 	.probe = qcom_scm_probe,
+	.shutdown = qcom_scm_shutdown,
 };
 
 static int __init qcom_scm_init(void)

drivers/firmware/qcom_scm.h

@@ -14,9 +14,11 @@
 
 #define QCOM_SCM_SVC_BOOT		0x1
 #define QCOM_SCM_BOOT_ADDR		0x1
+#define QCOM_SCM_SET_DLOAD_MODE		0x10
 #define QCOM_SCM_BOOT_ADDR_MC		0x11
 #define QCOM_SCM_SET_REMOTE_STATE	0xa
 extern int __qcom_scm_set_remote_state(struct device *dev, u32 state, u32 id);
+extern int __qcom_scm_set_dload_mode(struct device *dev, bool enable);
 
 #define QCOM_SCM_FLAG_HLOS		0x01
 #define QCOM_SCM_FLAG_COLDBOOT_MC	0x02
@@ -30,6 +32,12 @@ extern int __qcom_scm_set_cold_boot_addr(void *entry, const cpumask_t *cpus);
 #define QCOM_SCM_CMD_CORE_HOTPLUGGED	0x10
 extern void __qcom_scm_cpu_power_down(u32 flags);
 
+#define QCOM_SCM_SVC_IO			0x5
+#define QCOM_SCM_IO_READ		0x1
+#define QCOM_SCM_IO_WRITE		0x2
+extern int __qcom_scm_io_readl(struct device *dev, phys_addr_t addr, unsigned int *val);
+extern int __qcom_scm_io_writel(struct device *dev, phys_addr_t addr, unsigned int val);
+
 #define QCOM_SCM_SVC_INFO		0x6
 #define QCOM_IS_CALL_AVAIL_CMD		0x1
 extern int __qcom_scm_is_call_available(struct device *dev, u32 svc_id,

include/linux/qcom_scm.h

@@ -43,6 +43,8 @@ extern int qcom_scm_set_remote_state(u32 state, u32 id);
 extern int qcom_scm_restore_sec_cfg(u32 device_id, u32 spare);
 extern int qcom_scm_iommu_secure_ptbl_size(u32 spare, size_t *size);
 extern int qcom_scm_iommu_secure_ptbl_init(u64 addr, u32 size, u32 spare);
+extern int qcom_scm_io_readl(phys_addr_t addr, unsigned int *val);
+extern int qcom_scm_io_writel(phys_addr_t addr, unsigned int val);
 #else
 static inline
 int qcom_scm_set_cold_boot_addr(void *entry, const cpumask_t *cpus)
@@ -73,5 +75,7 @@ qcom_scm_set_remote_state(u32 state,u32 id) { return -ENODEV; }
 static inline int qcom_scm_restore_sec_cfg(u32 device_id, u32 spare) { return -ENODEV; }
 static inline int qcom_scm_iommu_secure_ptbl_size(u32 spare, size_t *size) { return -ENODEV; }
 static inline int qcom_scm_iommu_secure_ptbl_init(u64 addr, u32 size, u32 spare) { return -ENODEV; }
+static inline int qcom_scm_io_readl(phys_addr_t addr, unsigned int *val) { return -ENODEV; }
+static inline int qcom_scm_io_writel(phys_addr_t addr, unsigned int val) { return -ENODEV; }
 #endif
 #endif