Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-next

Jeff Kirsher says:

====================
This series contains updates to e1000e, ixgbevf, igb and igbvf.
Majority of the patches are code cleanups of e1000e where code
is removed (Yeah!).  The other two e1000e patches are fixes.  The
first is to fix the maximum frame size for 82579 devices.  The second
fix is to resolve an issue with devices other than 82579 that suffer
from dropped transactions on platforms with deep C-states when
jumbo frames are enabled.

The ixgbevf patch is to ensure that the driver fetches the correct,
refreshed value for link status and speed when the values have changed.

The igb and igbvf patches are a solution to an issue Stefan Assmann
reported, where when the PF is up and igbvf is loaded, the MAC address
is not generated using eth_hw_addr_random().
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/ethernet/intel/e1000e/80003es2lan.c

@@ -1010,7 +1010,7 @@ static s32 e1000_copper_link_setup_gg82563_80003es2lan(struct e1000_hw *hw)
 		return ret_val;
 
 	/* SW Reset the PHY so all changes take effect */
-	ret_val = e1000e_commit_phy(hw);
+	ret_val = hw->phy.ops.commit(hw);
 	if (ret_val) {
 		e_dbg("Error Resetting the PHY\n");
 		return ret_val;

drivers/net/ethernet/intel/e1000e/82571.c

@@ -1940,7 +1940,7 @@ static const struct e1000_phy_operations e82_phy_ops_m88 = {
 	.check_reset_block	= e1000e_check_reset_block_generic,
 	.commit			= e1000e_phy_sw_reset,
 	.force_speed_duplex	= e1000e_phy_force_speed_duplex_m88,
-	.get_cfg_done		= e1000e_get_cfg_done,
+	.get_cfg_done		= e1000e_get_cfg_done_generic,
 	.get_cable_length	= e1000e_get_cable_length_m88,
 	.get_info		= e1000e_get_phy_info_m88,
 	.read_reg		= e1000e_read_phy_reg_m88,
@@ -1958,7 +1958,7 @@ static const struct e1000_phy_operations e82_phy_ops_bm = {
 	.check_reset_block	= e1000e_check_reset_block_generic,
 	.commit			= e1000e_phy_sw_reset,
 	.force_speed_duplex	= e1000e_phy_force_speed_duplex_m88,
-	.get_cfg_done		= e1000e_get_cfg_done,
+	.get_cfg_done		= e1000e_get_cfg_done_generic,
 	.get_cable_length	= e1000e_get_cable_length_m88,
 	.get_info		= e1000e_get_phy_info_m88,
 	.read_reg		= e1000e_read_phy_reg_bm2,

drivers/net/ethernet/intel/e1000e/defines.h

@@ -261,8 +261,6 @@
 #define E1000_STATUS_PHYRA      0x00000400      /* PHY Reset Asserted */
 #define E1000_STATUS_GIO_MASTER_ENABLE 0x00080000 /* Status of Master requests. */
 
-/* Constants used to interpret the masked PCI-X bus speed. */
-
 #define HALF_DUPLEX 1
 #define FULL_DUPLEX 2
 
@@ -330,8 +328,6 @@
 #define E1000_TCTL_RTLC   0x01000000    /* Re-transmit on late collision */
 #define E1000_TCTL_MULR   0x10000000    /* Multiple request support */
 
-/* Transmit Arbitration Count */
-
 /* SerDes Control */
 #define E1000_SCTL_DISABLE_SERDES_LOOPBACK 0x0400
 
@@ -393,6 +389,8 @@
 #define E1000_PBA_8K  0x0008    /* 8KB */
 #define E1000_PBA_16K 0x0010    /* 16KB */
 
+#define E1000_PBA_RXA_MASK	0xFFFF
+
 #define E1000_PBS_16K E1000_PBA_16K
 
 /* Uncorrectable/correctable ECC Error counts and enable bits */
@@ -798,9 +796,6 @@
 #define M88E1000_PSCR_AUTO_X_1000T     0x0040
 /* Auto crossover enabled all speeds */
 #define M88E1000_PSCR_AUTO_X_MODE      0x0060
-/* 1=Enable Extended 10BASE-T distance (Lower 10BASE-T Rx Threshold)
- * 0=Normal 10BASE-T Rx Threshold
- */
 #define M88E1000_PSCR_ASSERT_CRS_ON_TX 0x0800 /* 1=Assert CRS on Transmit */
 
 /* M88E1000 PHY Specific Status Register */

drivers/net/ethernet/intel/e1000e/e1000.h

@@ -78,9 +78,6 @@ struct e1000_info;
 #define E1000_MIN_ITR_USECS		10 /* 100000 irq/sec */
 #define E1000_MAX_ITR_USECS		10000 /* 100    irq/sec */
 
-/* Early Receive defines */
-#define E1000_ERT_2048			0x100
-
 #define E1000_FC_PAUSE_TIME		0x0680 /* 858 usec */
 
 /* How many Tx Descriptors do we need to call netif_wake_queue ? */
@@ -579,8 +576,6 @@ extern const struct e1000_info e1000_es2_info;
 extern s32 e1000_read_pba_string_generic(struct e1000_hw *hw, u8 *pba_num,
 					 u32 pba_num_size);
 
-extern s32  e1000e_commit_phy(struct e1000_hw *hw);
-
 extern bool e1000e_enable_mng_pass_thru(struct e1000_hw *hw);
 
 extern bool e1000e_get_laa_state_82571(struct e1000_hw *hw);
@@ -654,7 +649,7 @@ extern s32 e1000e_write_phy_reg_igp_locked(struct e1000_hw *hw, u32 offset,
                                            u16 data);
 extern s32 e1000e_phy_sw_reset(struct e1000_hw *hw);
 extern s32 e1000e_phy_force_speed_duplex_m88(struct e1000_hw *hw);
-extern s32 e1000e_get_cfg_done(struct e1000_hw *hw);
+extern s32 e1000e_get_cfg_done_generic(struct e1000_hw *hw);
 extern s32 e1000e_get_cable_length_m88(struct e1000_hw *hw);
 extern s32 e1000e_get_phy_info_m88(struct e1000_hw *hw);
 extern s32 e1000e_read_phy_reg_m88(struct e1000_hw *hw, u32 offset, u16 *data);
@@ -737,11 +732,6 @@ static inline s32 e1e_wphy_locked(struct e1000_hw *hw, u32 offset, u16 data)
 	return hw->phy.ops.write_reg_locked(hw, offset, data);
 }
 
-static inline s32 e1000_get_cable_length(struct e1000_hw *hw)
-{
-	return hw->phy.ops.get_cable_length(hw);
-}
-
 extern s32 e1000e_acquire_nvm(struct e1000_hw *hw);
 extern s32 e1000e_write_nvm_spi(struct e1000_hw *hw, u16 offset, u16 words, u16 *data);
 extern s32 e1000e_update_nvm_checksum_generic(struct e1000_hw *hw);

drivers/net/ethernet/intel/e1000e/ethtool.c

@@ -1321,7 +1321,7 @@ static int e1000_integrated_phy_loopback(struct e1000_adapter *adapter)
 		phy_reg |= 0x006;
 		e1e_wphy(hw, PHY_REG(2, 21), phy_reg);
 		/* Assert SW reset for above settings to take effect */
-		e1000e_commit_phy(hw);
+		hw->phy.ops.commit(hw);
 		mdelay(1);
 		/* Force Full Duplex */
 		e1e_rphy(hw, PHY_REG(769, 16), &phy_reg);
@@ -1542,7 +1542,8 @@ static void e1000_loopback_cleanup(struct e1000_adapter *adapter)
 		if (phy_reg & MII_CR_LOOPBACK) {
 			phy_reg &= ~MII_CR_LOOPBACK;
 			e1e_wphy(hw, PHY_CONTROL, phy_reg);
-			e1000e_commit_phy(hw);
+			if (hw->phy.ops.commit)
+				hw->phy.ops.commit(hw);
 		}
 		break;
 	}

drivers/net/ethernet/intel/e1000e/hw.h

@@ -29,12 +29,9 @@
 #ifndef _E1000_HW_H_
 #define _E1000_HW_H_
 
-#include <linux/types.h>
+#include "defines.h"
 
 struct e1000_hw;
-struct e1000_adapter;
-
-#include "defines.h"
 
 enum e1e_registers {
 	E1000_CTRL     = 0x00000, /* Device Control - RW */
@@ -391,13 +388,11 @@ enum e1e_registers {
 #define E1000_DEV_ID_82573L			0x109A
 #define E1000_DEV_ID_82574L			0x10D3
 #define E1000_DEV_ID_82574LA			0x10F6
-#define E1000_DEV_ID_82583V                     0x150C
-
+#define E1000_DEV_ID_82583V			0x150C
 #define E1000_DEV_ID_80003ES2LAN_COPPER_DPT	0x1096
 #define E1000_DEV_ID_80003ES2LAN_SERDES_DPT	0x1098
 #define E1000_DEV_ID_80003ES2LAN_COPPER_SPT	0x10BA
 #define E1000_DEV_ID_80003ES2LAN_SERDES_SPT	0x10BB
-
 #define E1000_DEV_ID_ICH8_82567V_3		0x1501
 #define E1000_DEV_ID_ICH8_IGP_M_AMT		0x1049
 #define E1000_DEV_ID_ICH8_IGP_AMT		0x104A
@@ -432,12 +427,12 @@ enum e1e_registers {
 #define E1000_DEV_ID_PCH_LPTLP_I218_LM		0x155A
 #define E1000_DEV_ID_PCH_LPTLP_I218_V		0x1559
 
-#define E1000_REVISION_4 4
+#define E1000_REVISION_4	4
 
-#define E1000_FUNC_1 1
+#define E1000_FUNC_1		1
 
-#define E1000_ALT_MAC_ADDRESS_OFFSET_LAN0   0
-#define E1000_ALT_MAC_ADDRESS_OFFSET_LAN1   3
+#define E1000_ALT_MAC_ADDRESS_OFFSET_LAN0	0
+#define E1000_ALT_MAC_ADDRESS_OFFSET_LAN1	3
 
 enum e1000_mac_type {
 	e1000_82571,
@@ -664,7 +659,7 @@ struct e1000_data_desc {
 		struct {
 			u8 status;     /* Descriptor status */
 			u8 popts;      /* Packet Options */
-			__le16 special;   /* */
+			__le16 special;
 		} fields;
 	} upper;
 };
@@ -760,7 +755,7 @@ struct e1000_host_command_header {
 	u8 checksum;
 };
 
-#define E1000_HI_MAX_DATA_LENGTH     252
+#define E1000_HI_MAX_DATA_LENGTH	252
 struct e1000_host_command_info {
 	struct e1000_host_command_header command_header;
 	u8 command_data[E1000_HI_MAX_DATA_LENGTH];
@@ -775,13 +770,13 @@ struct e1000_host_mng_command_header {
 	u16 command_length;
 };
 
-#define E1000_HI_MAX_MNG_DATA_LENGTH 0x6F8
+#define E1000_HI_MAX_MNG_DATA_LENGTH	0x6F8
 struct e1000_host_mng_command_info {
 	struct e1000_host_mng_command_header command_header;
 	u8 command_data[E1000_HI_MAX_MNG_DATA_LENGTH];
 };
 
-/* Function pointers and static data for the MAC. */
+/* Function pointers for the MAC. */
 struct e1000_mac_operations {
 	s32  (*id_led_init)(struct e1000_hw *);
 	s32  (*blink_led)(struct e1000_hw *);

drivers/net/ethernet/intel/e1000e/ich8lan.c

@@ -4378,7 +4378,7 @@ static s32 e1000_get_cfg_done_ich8lan(struct e1000_hw *hw)
 	u32 bank = 0;
 	u32 status;
 
-	e1000e_get_cfg_done(hw);
+	e1000e_get_cfg_done_generic(hw);
 
 	/* Wait for indication from h/w that it has completed basic config */
 	if (hw->mac.type >= e1000_ich10lan) {
@@ -4620,7 +4620,7 @@ const struct e1000_info e1000_pch2_info = {
 	.flags2			= FLAG2_HAS_PHY_STATS
 				  | FLAG2_HAS_EEE,
 	.pba			= 26,
-	.max_hw_frame_size	= DEFAULT_JUMBO,
+	.max_hw_frame_size	= 9018,
 	.get_variants		= e1000_get_variants_ich8lan,
 	.mac_ops		= &ich8_mac_ops,
 	.phy_ops		= &ich8_phy_ops,

drivers/net/ethernet/intel/e1000e/netdev.c

@@ -3242,18 +3242,23 @@ static void e1000_configure_rx(struct e1000_adapter *adapter)
 		rxcsum &= ~E1000_RXCSUM_TUOFL;
 	ew32(RXCSUM, rxcsum);
 
-	if (adapter->hw.mac.type == e1000_pch2lan) {
-		/* With jumbo frames, excessive C-state transition
-		 * latencies result in dropped transactions.
-		 */
-		if (adapter->netdev->mtu > ETH_DATA_LEN) {
+	/* With jumbo frames, excessive C-state transition latencies result
+	 * in dropped transactions.
+	 */
+	if (adapter->netdev->mtu > ETH_DATA_LEN) {
+		u32 lat =
+		    ((er32(PBA) & E1000_PBA_RXA_MASK) * 1024 -
+		     adapter->max_frame_size) * 8 / 1000;
+
+		if (adapter->flags & FLAG_IS_ICH) {
 			u32 rxdctl = er32(RXDCTL(0));
 			ew32(RXDCTL(0), rxdctl | 0x3);
-			pm_qos_update_request(&adapter->netdev->pm_qos_req, 55);
-		} else {
-			pm_qos_update_request(&adapter->netdev->pm_qos_req,
-					      PM_QOS_DEFAULT_VALUE);
 		}
+
+		pm_qos_update_request(&adapter->netdev->pm_qos_req, lat);
+	} else {
+		pm_qos_update_request(&adapter->netdev->pm_qos_req,
+				      PM_QOS_DEFAULT_VALUE);
 	}
 
 	/* Enable Receives */
@@ -4281,10 +4286,8 @@ static int e1000_open(struct net_device *netdev)
 		e1000_update_mng_vlan(adapter);
 
 	/* DMA latency requirement to workaround jumbo issue */
-	if (adapter->hw.mac.type == e1000_pch2lan)
-		pm_qos_add_request(&adapter->netdev->pm_qos_req,
-				   PM_QOS_CPU_DMA_LATENCY,
-				   PM_QOS_DEFAULT_VALUE);
+	pm_qos_add_request(&adapter->netdev->pm_qos_req, PM_QOS_CPU_DMA_LATENCY,
+			   PM_QOS_DEFAULT_VALUE);
 
 	/* before we allocate an interrupt, we must be ready to handle it.
 	 * Setting DEBUG_SHIRQ in the kernel makes it fire an interrupt
@@ -4392,8 +4395,7 @@ static int e1000_close(struct net_device *netdev)
 	    !test_bit(__E1000_TESTING, &adapter->state))
 		e1000e_release_hw_control(adapter);
 
-	if (adapter->hw.mac.type == e1000_pch2lan)
-		pm_qos_remove_request(&adapter->netdev->pm_qos_req);
+	pm_qos_remove_request(&adapter->netdev->pm_qos_req);
 
 	pm_runtime_put_sync(&pdev->dev);
 

drivers/net/ethernet/intel/e1000e/phy.c

@@ -28,9 +28,6 @@
 
 #include "e1000.h"
 
-static s32 e1000_get_phy_cfg_done(struct e1000_hw *hw);
-static s32 e1000_phy_force_speed_duplex(struct e1000_hw *hw);
-static s32 e1000_set_d0_lplu_state(struct e1000_hw *hw, bool active);
 static s32 e1000_wait_autoneg(struct e1000_hw *hw);
 static s32 e1000_access_phy_wakeup_reg_bm(struct e1000_hw *hw, u32 offset,
 					  u16 *data, bool read, bool page_set);
@@ -791,7 +788,7 @@ s32 e1000e_copper_link_setup_m88(struct e1000_hw *hw)
 			if (ret_val)
 				return ret_val;
 			/* Commit the changes. */
-			ret_val = e1000e_commit_phy(hw);
+			ret_val = phy->ops.commit(hw);
 			if (ret_val) {
 				e_dbg("Error committing the PHY changes\n");
 				return ret_val;
@@ -847,10 +844,12 @@ s32 e1000e_copper_link_setup_m88(struct e1000_hw *hw)
 	}
 
 	/* Commit the changes. */
-	ret_val = e1000e_commit_phy(hw);
-	if (ret_val) {
-		e_dbg("Error committing the PHY changes\n");
-		return ret_val;
+	if (phy->ops.commit) {
+		ret_val = phy->ops.commit(hw);
+		if (ret_val) {
+			e_dbg("Error committing the PHY changes\n");
+			return ret_val;
+		}
 	}
 
 	if (phy->type == e1000_phy_82578) {
@@ -894,10 +893,12 @@ s32 e1000e_copper_link_setup_igp(struct e1000_hw *hw)
 	msleep(100);
 
 	/* disable lplu d0 during driver init */
-	ret_val = e1000_set_d0_lplu_state(hw, false);
-	if (ret_val) {
-		e_dbg("Error Disabling LPLU D0\n");
-		return ret_val;
+	if (hw->phy.ops.set_d0_lplu_state) {
+		ret_val = hw->phy.ops.set_d0_lplu_state(hw, false);
+		if (ret_val) {
+			e_dbg("Error Disabling LPLU D0\n");
+			return ret_val;
+		}
 	}
 	/* Configure mdi-mdix settings */
 	ret_val = e1e_rphy(hw, IGP01E1000_PHY_PORT_CTRL, &data);
@@ -1195,7 +1196,7 @@ s32 e1000e_setup_copper_link(struct e1000_hw *hw)
 		 * depending on user settings.
 		 */
 		e_dbg("Forcing Speed and Duplex\n");
-		ret_val = e1000_phy_force_speed_duplex(hw);
+		ret_val = hw->phy.ops.force_speed_duplex(hw);
 		if (ret_val) {
 			e_dbg("Error Forcing Speed and Duplex\n");
 			return ret_val;
@@ -1325,9 +1326,11 @@ s32 e1000e_phy_force_speed_duplex_m88(struct e1000_hw *hw)
 		return ret_val;
 
 	/* Reset the phy to commit changes. */
-	ret_val = e1000e_commit_phy(hw);
-	if (ret_val)
-		return ret_val;
+	if (hw->phy.ops.commit) {
+		ret_val = hw->phy.ops.commit(hw);
+		if (ret_val)
+			return ret_val;
+	}
 
 	if (phy->autoneg_wait_to_complete) {
 		e_dbg("Waiting for forced speed/duplex link on M88 phy.\n");
@@ -1961,7 +1964,7 @@ s32 e1000e_get_phy_info_m88(struct e1000_hw *hw)
 	phy->is_mdix = !!(phy_data & M88E1000_PSSR_MDIX);
 
 	if ((phy_data & M88E1000_PSSR_SPEED) == M88E1000_PSSR_1000MBS) {
-		ret_val = e1000_get_cable_length(hw);
+		ret_val = hw->phy.ops.get_cable_length(hw);
 		if (ret_val)
 			return ret_val;
 
@@ -2025,7 +2028,7 @@ s32 e1000e_get_phy_info_igp(struct e1000_hw *hw)
 
 	if ((data & IGP01E1000_PSSR_SPEED_MASK) ==
 	    IGP01E1000_PSSR_SPEED_1000MBPS) {
-		ret_val = e1000_get_cable_length(hw);
+		ret_val = phy->ops.get_cable_length(hw);
 		if (ret_val)
 			return ret_val;
 
@@ -2165,17 +2168,17 @@ s32 e1000e_phy_hw_reset_generic(struct e1000_hw *hw)
 
 	phy->ops.release(hw);
 
-	return e1000_get_phy_cfg_done(hw);
+	return phy->ops.get_cfg_done(hw);
 }
 
 /**
- *  e1000e_get_cfg_done - Generic configuration done
+ *  e1000e_get_cfg_done_generic - Generic configuration done
  *  @hw: pointer to the HW structure
  *
  *  Generic function to wait 10 milli-seconds for configuration to complete
  *  and return success.
  **/
-s32 e1000e_get_cfg_done(struct e1000_hw *hw)
+s32 e1000e_get_cfg_done_generic(struct e1000_hw *hw)
 {
 	mdelay(10);
 
@@ -2265,38 +2268,6 @@ s32 e1000e_phy_init_script_igp3(struct e1000_hw *hw)
 	return 0;
 }
 
-/* Internal function pointers */
-
-/**
- *  e1000_get_phy_cfg_done - Generic PHY configuration done
- *  @hw: pointer to the HW structure
- *
- *  Return success if silicon family did not implement a family specific
- *  get_cfg_done function.
- **/
-static s32 e1000_get_phy_cfg_done(struct e1000_hw *hw)
-{
-	if (hw->phy.ops.get_cfg_done)
-		return hw->phy.ops.get_cfg_done(hw);
-
-	return 0;
-}
-
-/**
- *  e1000_phy_force_speed_duplex - Generic force PHY speed/duplex
- *  @hw: pointer to the HW structure
- *
- *  When the silicon family has not implemented a forced speed/duplex
- *  function for the PHY, simply return 0.
- **/
-static s32 e1000_phy_force_speed_duplex(struct e1000_hw *hw)
-{
-	if (hw->phy.ops.force_speed_duplex)
-		return hw->phy.ops.force_speed_duplex(hw);
-
-	return 0;
-}
-
 /**
  *  e1000e_get_phy_type_from_id - Get PHY type from id
  *  @phy_id: phy_id read from the phy
@@ -2804,43 +2775,6 @@ void e1000_power_down_phy_copper(struct e1000_hw *hw)
 	usleep_range(1000, 2000);
 }
 
-/**
- *  e1000e_commit_phy - Soft PHY reset
- *  @hw: pointer to the HW structure
- *
- *  Performs a soft PHY reset on those that apply. This is a function pointer
- *  entry point called by drivers.
- **/
-s32 e1000e_commit_phy(struct e1000_hw *hw)
-{
-	if (hw->phy.ops.commit)
-		return hw->phy.ops.commit(hw);
-
-	return 0;
-}
-
-/**
- *  e1000_set_d0_lplu_state - Sets low power link up state for D0
- *  @hw: pointer to the HW structure
- *  @active: boolean used to enable/disable lplu
- *
- *  Success returns 0, Failure returns 1
- *
- *  The low power link up (lplu) state is set to the power management level D0
- *  and SmartSpeed is disabled when active is true, else clear lplu for D0
- *  and enable Smartspeed.  LPLU and Smartspeed are mutually exclusive.  LPLU
- *  is used during Dx states where the power conservation is most important.
- *  During driver activity, SmartSpeed should be enabled so performance is
- *  maintained.  This is a function pointer entry point called by drivers.
- **/
-static s32 e1000_set_d0_lplu_state(struct e1000_hw *hw, bool active)
-{
-	if (hw->phy.ops.set_d0_lplu_state)
-		return hw->phy.ops.set_d0_lplu_state(hw, active);
-
-	return 0;
-}
-
 /**
  *  __e1000_read_phy_reg_hv -  Read HV PHY register
  *  @hw: pointer to the HW structure

drivers/net/ethernet/intel/igb/igb_main.c

@@ -5197,7 +5197,7 @@ static int igb_vf_configure(struct igb_adapter *adapter, int vf)
 {
 	unsigned char mac_addr[ETH_ALEN];
 
-	eth_random_addr(mac_addr);
+	eth_zero_addr(mac_addr);
 	igb_set_vf_mac(adapter, vf, mac_addr);
 
 	return 0;
@@ -5550,9 +5550,9 @@ static void igb_vf_reset_event(struct igb_adapter *adapter, u32 vf)
 {
 	unsigned char *vf_mac = adapter->vf_data[vf].vf_mac_addresses;
 
-	/* generate a new mac address as we were hotplug removed/added */
+	/* clear mac address as we were hotplug removed/added */
 	if (!(adapter->vf_data[vf].flags & IGB_VF_FLAG_PF_SET_MAC))
-		eth_random_addr(vf_mac);
+		eth_zero_addr(vf_mac);
 
 	/* process remaining reset events */
 	igb_vf_reset(adapter, vf);

drivers/net/ethernet/intel/igbvf/netdev.c

@@ -2735,26 +2735,22 @@ static int igbvf_probe(struct pci_dev *pdev, const struct pci_device_id *ent)
 	err = hw->mac.ops.reset_hw(hw);
 	if (err) {
 		dev_info(&pdev->dev,
-			 "PF still in reset state, assigning new address."
-			 " Is the PF interface up?\n");
-		eth_hw_addr_random(netdev);
-		memcpy(adapter->hw.mac.addr, netdev->dev_addr,
-			netdev->addr_len);
+			 "PF still in reset state. Is the PF interface up?\n");
 	} else {
 		err = hw->mac.ops.read_mac_addr(hw);
-		if (err) {
-			dev_err(&pdev->dev, "Error reading MAC address\n");
-			goto err_hw_init;
-		}
+		if (err)
+			dev_info(&pdev->dev, "Error reading MAC address.\n");
+		else if (is_zero_ether_addr(adapter->hw.mac.addr))
+			dev_info(&pdev->dev, "MAC address not assigned by administrator.\n");
 		memcpy(netdev->dev_addr, adapter->hw.mac.addr,
-			netdev->addr_len);
+		       netdev->addr_len);
 	}
 
 	if (!is_valid_ether_addr(netdev->dev_addr)) {
-		dev_err(&pdev->dev, "Invalid MAC Address: %pM\n",
-		        netdev->dev_addr);
-		err = -EIO;
-		goto err_hw_init;
+		dev_info(&pdev->dev, "Assigning random MAC address.\n");
+		eth_hw_addr_random(netdev);
+		memcpy(adapter->hw.mac.addr, netdev->dev_addr,
+			netdev->addr_len);
 	}
 
 	setup_timer(&adapter->watchdog_timer, &igbvf_watchdog,

drivers/net/ethernet/intel/ixgbevf/ethtool.c

@@ -99,6 +99,7 @@ static int ixgbevf_get_settings(struct net_device *netdev,
 	ecmd->transceiver = XCVR_DUMMY1;
 	ecmd->port = -1;
 
+	hw->mac.get_link_status = 1;
 	hw->mac.ops.check_link(hw, &link_speed, &link_up, false);
 
 	if (link_up) {