Commit 8ad38d22 authored by Rajkumar Manoharan's avatar Rajkumar Manoharan Committed by John W. Linville

ath9k_hw: Disable Walsh spatial spreading for 2 chains

The Walsh bit is disabled for regulatory consideration.

FCC limit for walsh enable is lower than that for walsh disable. So
disabling walsh bit will not limit tx power/affect tx power even in
cases where we are not FCC limited (most client cards). If the tx
power is not FCC limited, then enabling/disabling walsh bit will
not affect Avg. EVM/overall performance in any visible manner.

Cc: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: default avatarRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: default avatarJohn W. Linville <linville@tuxdriver.com>
parent a35e2780
...@@ -636,7 +636,7 @@ static const u32 ar9300_2p2_baseband_postamble[][5] = { ...@@ -636,7 +636,7 @@ static const u32 ar9300_2p2_baseband_postamble[][5] = {
{0x00009e44, 0x02321e27, 0x02321e27, 0x02291e27, 0x02291e27}, {0x00009e44, 0x02321e27, 0x02321e27, 0x02291e27, 0x02291e27},
{0x00009e48, 0x5030201a, 0x5030201a, 0x50302012, 0x50302012}, {0x00009e48, 0x5030201a, 0x5030201a, 0x50302012, 0x50302012},
{0x00009fc8, 0x0003f000, 0x0003f000, 0x0001a000, 0x0001a000}, {0x00009fc8, 0x0003f000, 0x0003f000, 0x0001a000, 0x0001a000},
{0x0000a204, 0x000037c0, 0x000037c4, 0x000037c4, 0x000037c0}, {0x0000a204, 0x000036c0, 0x000036c4, 0x000036c4, 0x000036c0},
{0x0000a208, 0x00000104, 0x00000104, 0x00000004, 0x00000004}, {0x0000a208, 0x00000104, 0x00000104, 0x00000004, 0x00000004},
{0x0000a22c, 0x01026a2f, 0x01026a2f, 0x01026a2f, 0x01026a2f}, {0x0000a22c, 0x01026a2f, 0x01026a2f, 0x01026a2f, 0x01026a2f},
{0x0000a230, 0x0000000a, 0x00000014, 0x00000016, 0x0000000b}, {0x0000a230, 0x0000000a, 0x00000014, 0x00000016, 0x0000000b},
......
...@@ -482,7 +482,7 @@ static void ar9003_hw_set_channel_regs(struct ath_hw *ah, ...@@ -482,7 +482,7 @@ static void ar9003_hw_set_channel_regs(struct ath_hw *ah,
(REG_READ(ah, AR_PHY_GEN_CTRL) & AR_PHY_GC_ENABLE_DAC_FIFO); (REG_READ(ah, AR_PHY_GEN_CTRL) & AR_PHY_GC_ENABLE_DAC_FIFO);
/* Enable 11n HT, 20 MHz */ /* Enable 11n HT, 20 MHz */
phymode = AR_PHY_GC_HT_EN | AR_PHY_GC_SINGLE_HT_LTF1 | AR_PHY_GC_WALSH | phymode = AR_PHY_GC_HT_EN | AR_PHY_GC_SINGLE_HT_LTF1 |
AR_PHY_GC_SHORT_GI_40 | enableDacFifo; AR_PHY_GC_SHORT_GI_40 | enableDacFifo;
/* Configure baseband for dynamic 20/40 operation */ /* Configure baseband for dynamic 20/40 operation */
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment