Commit 8cecf52b authored by Tomi Valkeinen's avatar Tomi Valkeinen

ARM: omap3-beagle.dts: add display information

Add DT data for OMAP3 Beagle board. The board has the following displays:

dvi: uses TFP410 encoder to convert DPI to DVI
tv: analog svideo
Signed-off-by: default avatarTomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: default avatarTony Lindgren <tony@atomide.com>
parent 7c572d5e
......@@ -24,6 +24,11 @@ memory {
reg = <0x80000000 0x10000000>; /* 256 MB */
};
aliases {
display0 = &dvi0;
display1 = &tv0;
};
leds {
compatible = "gpio-leds";
pmu_stat {
......@@ -80,6 +85,61 @@ user {
};
};
tfp410: encoder@0 {
compatible = "ti,tfp410";
powerdown-gpios = <&gpio6 10 GPIO_ACTIVE_LOW>; /* gpio_170 */
pinctrl-names = "default";
pinctrl-0 = <&tfp410_pins>;
ports {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
tfp410_in: endpoint@0 {
remote-endpoint = <&dpi_out>;
};
};
port@1 {
reg = <1>;
tfp410_out: endpoint@0 {
remote-endpoint = <&dvi_connector_in>;
};
};
};
};
dvi0: connector@0 {
compatible = "dvi-connector";
label = "dvi";
digital;
ddc-i2c-bus = <&i2c3>;
port {
dvi_connector_in: endpoint {
remote-endpoint = <&tfp410_out>;
};
};
};
tv0: connector@1 {
compatible = "svideo-connector";
label = "tv";
port {
tv_connector_in: endpoint {
remote-endpoint = <&venc_out>;
};
};
};
};
&omap3_pmx_wkup {
......@@ -113,6 +173,45 @@ uart3_pins: pinmux_uart3_pins {
0x170 (PIN_OUTPUT | MUX_MODE0) /* uart3_tx_irtx.uart3_tx_irtx */
>;
};
tfp410_pins: pinmux_tfp410_pins {
pinctrl-single,pins = <
0x194 (PIN_OUTPUT | MUX_MODE4) /* hdq_sio.gpio_170 */
>;
};
dss_dpi_pins: pinmux_dss_dpi_pins {
pinctrl-single,pins = <
0x0a4 (PIN_OUTPUT | MUX_MODE0) /* dss_pclk.dss_pclk */
0x0a6 (PIN_OUTPUT | MUX_MODE0) /* dss_hsync.dss_hsync */
0x0a8 (PIN_OUTPUT | MUX_MODE0) /* dss_vsync.dss_vsync */
0x0aa (PIN_OUTPUT | MUX_MODE0) /* dss_acbias.dss_acbias */
0x0ac (PIN_OUTPUT | MUX_MODE0) /* dss_data0.dss_data0 */
0x0ae (PIN_OUTPUT | MUX_MODE0) /* dss_data1.dss_data1 */
0x0b0 (PIN_OUTPUT | MUX_MODE0) /* dss_data2.dss_data2 */
0x0b2 (PIN_OUTPUT | MUX_MODE0) /* dss_data3.dss_data3 */
0x0b4 (PIN_OUTPUT | MUX_MODE0) /* dss_data4.dss_data4 */
0x0b6 (PIN_OUTPUT | MUX_MODE0) /* dss_data5.dss_data5 */
0x0b8 (PIN_OUTPUT | MUX_MODE0) /* dss_data6.dss_data6 */
0x0ba (PIN_OUTPUT | MUX_MODE0) /* dss_data7.dss_data7 */
0x0bc (PIN_OUTPUT | MUX_MODE0) /* dss_data8.dss_data8 */
0x0be (PIN_OUTPUT | MUX_MODE0) /* dss_data9.dss_data9 */
0x0c0 (PIN_OUTPUT | MUX_MODE0) /* dss_data10.dss_data10 */
0x0c2 (PIN_OUTPUT | MUX_MODE0) /* dss_data11.dss_data11 */
0x0c4 (PIN_OUTPUT | MUX_MODE0) /* dss_data12.dss_data12 */
0x0c6 (PIN_OUTPUT | MUX_MODE0) /* dss_data13.dss_data13 */
0x0c8 (PIN_OUTPUT | MUX_MODE0) /* dss_data14.dss_data14 */
0x0ca (PIN_OUTPUT | MUX_MODE0) /* dss_data15.dss_data15 */
0x0cc (PIN_OUTPUT | MUX_MODE0) /* dss_data16.dss_data16 */
0x0ce (PIN_OUTPUT | MUX_MODE0) /* dss_data17.dss_data17 */
0x0d0 (PIN_OUTPUT | MUX_MODE0) /* dss_data18.dss_data18 */
0x0d2 (PIN_OUTPUT | MUX_MODE0) /* dss_data19.dss_data19 */
0x0d4 (PIN_OUTPUT | MUX_MODE0) /* dss_data20.dss_data20 */
0x0d6 (PIN_OUTPUT | MUX_MODE0) /* dss_data21.dss_data21 */
0x0d8 (PIN_OUTPUT | MUX_MODE0) /* dss_data22.dss_data22 */
0x0da (PIN_OUTPUT | MUX_MODE0) /* dss_data23.dss_data23 */
>;
};
};
&omap3_pmx_core2 {
......@@ -152,6 +251,10 @@ codec {
#include "twl4030.dtsi"
#include "twl4030_omap3.dtsi"
&i2c3 {
clock-frequency = <100000>;
};
&mmc1 {
vmmc-supply = <&vmmc1>;
vmmc_aux-supply = <&vsim>;
......@@ -215,3 +318,35 @@ &vaux2 {
&mcbsp2 {
status = "okay";
};
/* Needed to power the DPI pins */
&vpll2 {
regulator-always-on;
};
&dss {
status = "ok";
pinctrl-names = "default";
pinctrl-0 = <&dss_dpi_pins>;
port {
dpi_out: endpoint {
remote-endpoint = <&tfp410_in>;
data-lines = <24>;
};
};
};
&venc {
status = "ok";
vdda-supply = <&vdac>;
port {
venc_out: endpoint {
remote-endpoint = <&tv_connector_in>;
ti,channels = <2>;
};
};
};
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment