Merge tag 'phy-for-6.9' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy

Pull phy updates from Vinod Koul:
 "New hardware support:

   - Qualcomm X1E80100 PCIe phy support, SM8550 PCIe1 PHY, SC7180 UFS
     PHY and SDM630 USBC support

   - Rockchip HDMI/eDP Combo PHY driver

   - Mediatek MT8365 CSI phy driver

  Updates:

   - Rework on Qualcomm phy PCS registers and type-c handling

   - Cadence torrent phy updates for multilink configuration

   - TI gmii resume support"

* tag 'phy-for-6.9' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy: (41 commits)
  phy: constify of_phandle_args in xlate
  phy: ti: tusb1210: Define device IDs
  phy: ti: tusb1210: Use temporary variable for struct device
  phy: rockchip: Add Samsung HDMI/eDP Combo PHY driver
  dt-bindings: phy: Add Rockchip HDMI/eDP Combo PHY schema
  phy: ti: gmii-sel: add resume support
  phy: mtk-mipi-csi: add driver for CSI phy
  dt-bindings: phy: add mediatek MIPI CD-PHY module v0.5
  phy: cadence-torrent: Add USXGMII(156.25MHz) + SGMII/QSGMII(100MHz) multilink config for TI J7200
  dt-bindings: phy: cadence-torrent: Add a separate compatible for TI J7200
  phy: cadence-torrent: Add USXGMII(156.25MHz) + SGMII/QSGMII(100MHz) multilink configuration
  phy: cadence-torrent: Add PCIe(100MHz) + USXGMII(156.25MHz) multilink configuration
  dt-bindings: phy: cadence-torrent: Add optional input reference clock for PLL1
  phy: qcom-qmp-ufs: Switch to devm_clk_bulk_get_all() API
  dt-bindings: phy: qmp-ufs: Fix PHY clocks
  phy: qcom: sgmii-eth: move PCS registers to separate header
  phy: qcom: sgmii-eth: use existing register definitions
  phy: qcom: qmp-usbc: drop has_pwrdn_delay handling
  phy: qcom: qmp: move common bits definitions to common header
  phy: qcom: qmp: split DP PHY registers to separate headers
  ...

Documentation/devicetree/bindings/phy/mediatek,mt8365-csi-rx.yaml

+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+# Copyright (c) 2023 MediaTek, BayLibre
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/phy/mediatek,mt8365-csi-rx.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Mediatek Sensor Interface MIPI CSI CD-PHY
+
+maintainers:
+  - Julien Stephan <jstephan@baylibre.com>
+  - Andy Hsieh <andy.hsieh@mediatek.com>
+
+description:
+  The SENINF CD-PHY is a set of CD-PHY connected to the SENINF CSI-2
+  receivers. The number of PHYs depends on the SoC model.
+  Depending on the SoC model, each PHYs can be either CD-PHY or D-PHY only
+  capable.
+
+properties:
+  compatible:
+    enum:
+      - mediatek,mt8365-csi-rx
+
+  reg:
+    maxItems: 1
+
+  num-lanes:
+    enum: [2, 3, 4]
+
+  '#phy-cells':
+    enum: [0, 1]
+    description: |
+      If the PHY doesn't support mode selection then #phy-cells must be 0 and
+      PHY mode is described using phy-type property.
+      If the PHY supports mode selection, then #phy-cells must be 1 and mode
+      is set in the PHY cells. Supported modes are:
+        - PHY_TYPE_DPHY
+        - PHY_TYPE_CPHY
+      See include/dt-bindings/phy/phy.h for constants.
+
+  phy-type:
+    description:
+      If the PHY doesn't support mode selection then this set the operating mode.
+      See include/dt-bindings/phy/phy.h for constants.
+    const: 10
+    $ref: /schemas/types.yaml#/definitions/uint32
+
+required:
+  - compatible
+  - reg
+  - num-lanes
+  - '#phy-cells'
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/phy/phy.h>
+    soc {
+      #address-cells = <2>;
+      #size-cells = <2>;
+
+      csi0_rx: phy@11c10000 {
+        compatible = "mediatek,mt8365-csi-rx";
+        reg = <0 0x11c10000 0 0x2000>;
+        num-lanes = <2>;
+        #phy-cells = <1>;
+      };
+
+      csi1_rx: phy@11c12000 {
+        compatible = "mediatek,mt8365-csi-rx";
+        reg = <0 0x11c12000 0 0x2000>;
+        phy-type = <PHY_TYPE_DPHY>;
+        num-lanes = <2>;
+        #phy-cells = <0>;
+      };
+    };
+...

Documentation/devicetree/bindings/phy/phy-cadence-torrent.yaml

@@ -20,6 +20,7 @@ properties:
   compatible:
     enum:
       - cdns,torrent-phy
+      - ti,j7200-serdes-10g
       - ti,j721e-serdes-10g
 
   '#address-cells':
@@ -35,14 +36,18 @@ properties:
     minItems: 1
     maxItems: 2
     description:
-      PHY reference clock for 1 item. Must contain an entry in clock-names.
-      Optional Parent to enable output reference clock.
+      PHY input reference clocks - refclk (for PLL0) & pll1_refclk (for PLL1).
+      pll1_refclk is optional and used for multi-protocol configurations requiring
+      separate reference clock for each protocol.
+      Same refclk is used for both PLL0 and PLL1 if no separate pll1_refclk is used.
+      Optional parent clock (phy_en_refclk) to enable a reference clock output feature
+      on some platforms to output either derived or received reference clock.
 
   clock-names:
     minItems: 1
     items:
       - const: refclk
-      - const: phy_en_refclk
+      - enum: [ pll1_refclk, phy_en_refclk ]
 
   reg:
     minItems: 1

Documentation/devicetree/bindings/phy/qcom,msm8998-qmp-usb3-phy.yaml

+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/phy/qcom,msm8998-qmp-usb3-phy.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm QMP PHY controller (USB, MSM8998)
+
+maintainers:
+  - Vinod Koul <vkoul@kernel.org>
+
+description:
+  The QMP PHY controller supports physical layer functionality for USB-C on
+  several Qualcomm chipsets.
+
+properties:
+  compatible:
+    enum:
+      - qcom,msm8998-qmp-usb3-phy
+      - qcom,qcm2290-qmp-usb3-phy
+      - qcom,sdm660-qmp-usb3-phy
+      - qcom,sm6115-qmp-usb3-phy
+
+  reg:
+    maxItems: 1
+
+  clocks:
+    maxItems: 4
+
+  clock-names:
+    maxItems: 4
+
+  resets:
+    maxItems: 2
+
+  reset-names:
+    items:
+      - const: phy
+      - const: phy_phy
+
+  vdda-phy-supply: true
+
+  vdda-pll-supply: true
+
+  "#clock-cells":
+    const: 0
+
+  clock-output-names:
+    maxItems: 1
+
+  "#phy-cells":
+    const: 0
+
+  orientation-switch:
+    description:
+      Flag the PHY as possible handler of USB Type-C orientation switching
+    type: boolean
+
+  qcom,tcsr-reg:
+    $ref: /schemas/types.yaml#/definitions/phandle-array
+    items:
+      - items:
+          - description: phandle to TCSR hardware block
+          - description: offset of the VLS CLAMP register
+    description: Clamp register present in the TCSR
+
+  ports:
+    $ref: /schemas/graph.yaml#/properties/ports
+    properties:
+      port@0:
+        $ref: /schemas/graph.yaml#/properties/port
+        description: Output endpoint of the PHY
+
+      port@1:
+        $ref: /schemas/graph.yaml#/properties/port
+        description: Incoming endpoint from the USB controller
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - clock-names
+  - resets
+  - reset-names
+  - vdda-phy-supply
+  - vdda-pll-supply
+  - "#clock-cells"
+  - clock-output-names
+  - "#phy-cells"
+  - qcom,tcsr-reg
+
+allOf:
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - qcom,msm8998-qmp-usb3-phy
+              - qcom,sdm660-qmp-usb3-phy
+    then:
+      properties:
+        clocks:
+          maxItems: 4
+        clock-names:
+          items:
+            - const: aux
+            - const: ref
+            - const: cfg_ahb
+            - const: pipe
+
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - qcom,qcm2290-qmp-usb3-phy
+              - qcom,sm6115-qmp-usb3-phy
+    then:
+      properties:
+        clocks:
+          maxItems: 4
+        clock-names:
+          items:
+            - const: cfg_ahb
+            - const: ref
+            - const: com_aux
+            - const: pipe
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/qcom,gcc-msm8998.h>
+    #include <dt-bindings/clock/qcom,rpmh.h>
+
+    phy@c010000 {
+      compatible = "qcom,msm8998-qmp-usb3-phy";
+      reg = <0x0c010000 0x1000>;
+
+      clocks = <&gcc GCC_USB3_PHY_AUX_CLK>,
+               <&gcc GCC_USB3_CLKREF_CLK>,
+               <&gcc GCC_USB_PHY_CFG_AHB2PHY_CLK>,
+               <&gcc GCC_USB3_PHY_PIPE_CLK>;
+      clock-names = "aux",
+                    "ref",
+                    "cfg_ahb",
+                    "pipe";
+      clock-output-names = "usb3_phy_pipe_clk_src";
+      #clock-cells = <0>;
+      #phy-cells = <0>;
+
+      resets = <&gcc GCC_USB3_PHY_BCR>,
+               <&gcc GCC_USB3PHY_PHY_BCR>;
+      reset-names = "phy",
+                    "phy_phy";
+
+      vdda-phy-supply = <&vreg_l1a_0p875>;
+      vdda-pll-supply = <&vreg_l2a_1p2>;
+
+      orientation-switch;
+
+      qcom,tcsr-reg = <&tcsr_regs_1 0x6b244>;
+
+      ports {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        port@0 {
+          reg = <0>;
+
+          endpoint {
+            remote-endpoint = <&pmic_typec_mux_in>;
+          };
+        };
+
+        port@1 {
+          reg = <1>;
+
+          endpoint {
+            remote-endpoint = <&usb_dwc3_ss>;
+          };
+        };
+      };
+    };

Documentation/devicetree/bindings/phy/qcom,sc8280xp-qmp-pcie-phy.yaml

@@ -38,6 +38,8 @@ properties:
       - qcom,sm8550-qmp-gen4x2-pcie-phy
       - qcom,sm8650-qmp-gen3x2-pcie-phy
       - qcom,sm8650-qmp-gen4x2-pcie-phy
+      - qcom,x1e80100-qmp-gen3x2-pcie-phy
+      - qcom,x1e80100-qmp-gen4x2-pcie-phy
 
   reg:
     minItems: 1
@@ -151,6 +153,8 @@ allOf:
               - qcom,sm8550-qmp-gen4x2-pcie-phy
               - qcom,sm8650-qmp-gen3x2-pcie-phy
               - qcom,sm8650-qmp-gen4x2-pcie-phy
+              - qcom,x1e80100-qmp-gen3x2-pcie-phy
+              - qcom,x1e80100-qmp-gen4x2-pcie-phy
     then:
       properties:
         clocks:
@@ -194,6 +198,8 @@ allOf:
             enum:
               - qcom,sm8550-qmp-gen4x2-pcie-phy
               - qcom,sm8650-qmp-gen4x2-pcie-phy
+              - qcom,x1e80100-qmp-gen3x2-pcie-phy
+              - qcom,x1e80100-qmp-gen4x2-pcie-phy
     then:
       properties:
         resets:

Documentation/devicetree/bindings/phy/qcom,sc8280xp-qmp-ufs-phy.yaml

@@ -19,6 +19,7 @@ properties:
       - qcom,msm8996-qmp-ufs-phy
       - qcom,msm8998-qmp-ufs-phy
       - qcom,sa8775p-qmp-ufs-phy
+      - qcom,sc7180-qmp-ufs-phy
       - qcom,sc7280-qmp-ufs-phy
       - qcom,sc8180x-qmp-ufs-phy
       - qcom,sc8280xp-qmp-ufs-phy
@@ -38,15 +39,12 @@ properties:
     maxItems: 1
 
   clocks:
-    minItems: 1
+    minItems: 2
     maxItems: 3
 
   clock-names:
-    minItems: 1
-    items:
-      - const: ref
-      - const: ref_aux
-      - const: qref
+    minItems: 2
+    maxItems: 3
 
   power-domains:
     maxItems: 1
@@ -86,22 +84,9 @@ allOf:
         compatible:
           contains:
             enum:
+              - qcom,msm8998-qmp-ufs-phy
               - qcom,sa8775p-qmp-ufs-phy
               - qcom,sc7280-qmp-ufs-phy
-              - qcom,sm8450-qmp-ufs-phy
-    then:
-      properties:
-        clocks:
-          minItems: 3
-        clock-names:
-          minItems: 3
-
-  - if:
-      properties:
-        compatible:
-          contains:
-            enum:
-              - qcom,msm8998-qmp-ufs-phy
               - qcom,sc8180x-qmp-ufs-phy
               - qcom,sc8280xp-qmp-ufs-phy
               - qcom,sdm845-qmp-ufs-phy
@@ -112,14 +97,19 @@ allOf:
               - qcom,sm8150-qmp-ufs-phy
               - qcom,sm8250-qmp-ufs-phy
               - qcom,sm8350-qmp-ufs-phy
+              - qcom,sm8450-qmp-ufs-phy
               - qcom,sm8550-qmp-ufs-phy
               - qcom,sm8650-qmp-ufs-phy
     then:
       properties:
         clocks:
-          maxItems: 2
+          minItems: 3
+          maxItems: 3
         clock-names:
-          maxItems: 2
+          items:
+            - const: ref
+            - const: ref_aux
+            - const: qref
 
   - if:
       properties:
@@ -130,22 +120,28 @@ allOf:
     then:
       properties:
         clocks:
-          maxItems: 1
+          minItems: 2
+          maxItems: 2
         clock-names:
-          maxItems: 1
+          items:
+            - const: ref
+            - const: qref
 
 additionalProperties: false
 
 examples:
   - |
     #include <dt-bindings/clock/qcom,gcc-sc8280xp.h>
+    #include <dt-bindings/clock/qcom,rpmh.h>
 
     ufs_mem_phy: phy@1d87000 {
         compatible = "qcom,sc8280xp-qmp-ufs-phy";
         reg = <0x01d87000 0x1000>;
 
-        clocks = <&gcc GCC_UFS_REF_CLKREF_CLK>, <&gcc GCC_UFS_PHY_PHY_AUX_CLK>;
-        clock-names = "ref", "ref_aux";
+        clocks = <&rpmhcc RPMH_CXO_CLK>, <&gcc GCC_UFS_PHY_PHY_AUX_CLK>,
+                 <&gcc GCC_UFS_REF_CLKREF_CLK>;
+
+        clock-names = "ref", "ref_aux", "qref";
 
         power-domains = <&gcc UFS_PHY_GDSC>;
 

Documentation/devicetree/bindings/phy/qcom,sc8280xp-qmp-usb3-uni-phy.yaml

@@ -20,15 +20,12 @@ properties:
       - qcom,ipq8074-qmp-usb3-phy
       - qcom,ipq9574-qmp-usb3-phy
       - qcom,msm8996-qmp-usb3-phy
-      - qcom,msm8998-qmp-usb3-phy
-      - qcom,qcm2290-qmp-usb3-phy
       - qcom,sa8775p-qmp-usb3-uni-phy
       - qcom,sc8280xp-qmp-usb3-uni-phy
       - qcom,sdm845-qmp-usb3-uni-phy
       - qcom,sdx55-qmp-usb3-uni-phy
       - qcom,sdx65-qmp-usb3-uni-phy
       - qcom,sdx75-qmp-usb3-uni-phy
-      - qcom,sm6115-qmp-usb3-phy
       - qcom,sm8150-qmp-usb3-uni-phy
       - qcom,sm8250-qmp-usb3-uni-phy
       - qcom,sm8350-qmp-usb3-uni-phy
@@ -93,7 +90,6 @@ allOf:
               - qcom,ipq8074-qmp-usb3-phy
               - qcom,ipq9574-qmp-usb3-phy
               - qcom,msm8996-qmp-usb3-phy
-              - qcom,msm8998-qmp-usb3-phy
               - qcom,sdx55-qmp-usb3-uni-phy
               - qcom,sdx65-qmp-usb3-uni-phy
               - qcom,sdx75-qmp-usb3-uni-phy
@@ -108,24 +104,6 @@ allOf:
             - const: cfg_ahb
             - const: pipe
 
-  - if:
-      properties:
-        compatible:
-          contains:
-            enum:
-              - qcom,qcm2290-qmp-usb3-phy
-              - qcom,sm6115-qmp-usb3-phy
-    then:
-      properties:
-        clocks:
-          maxItems: 4
-        clock-names:
-          items:
-            - const: cfg_ahb
-            - const: ref
-            - const: com_aux
-            - const: pipe
-
   - if:
       properties:
         compatible:

Documentation/devicetree/bindings/phy/rockchip,rk3588-hdptx-phy.yaml

+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/phy/rockchip,rk3588-hdptx-phy.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Rockchip SoC HDMI/eDP Transmitter Combo PHY
+
+maintainers:
+  - Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
+
+properties:
+  compatible:
+    enum:
+      - rockchip,rk3588-hdptx-phy
+
+  reg:
+    maxItems: 1
+
+  clocks:
+    items:
+      - description: Reference clock
+      - description: APB clock
+
+  clock-names:
+    items:
+      - const: ref
+      - const: apb
+
+  "#phy-cells":
+    const: 0
+
+  resets:
+    items:
+      - description: PHY reset line
+      - description: APB reset line
+      - description: INIT reset line
+      - description: CMN reset line
+      - description: LANE reset line
+      - description: ROPLL reset line
+      - description: LCPLL reset line
+
+  reset-names:
+    items:
+      - const: phy
+      - const: apb
+      - const: init
+      - const: cmn
+      - const: lane
+      - const: ropll
+      - const: lcpll
+
+  rockchip,grf:
+    $ref: /schemas/types.yaml#/definitions/phandle
+    description: Some PHY related data is accessed through GRF regs.
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - clock-names
+  - "#phy-cells"
+  - resets
+  - reset-names
+  - rockchip,grf
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/rockchip,rk3588-cru.h>
+    #include <dt-bindings/reset/rockchip,rk3588-cru.h>
+
+    soc {
+      #address-cells = <2>;
+      #size-cells = <2>;
+
+      phy@fed60000 {
+        compatible = "rockchip,rk3588-hdptx-phy";
+        reg = <0x0 0xfed60000 0x0 0x2000>;
+        clocks = <&cru CLK_USB2PHY_HDPTXRXPHY_REF>, <&cru PCLK_HDPTX0>;
+        clock-names = "ref", "apb";
+        #phy-cells = <0>;
+        resets = <&cru SRST_HDPTX0>, <&cru SRST_P_HDPTX0>,
+                 <&cru SRST_HDPTX0_INIT>, <&cru SRST_HDPTX0_CMN>,
+                 <&cru SRST_HDPTX0_LANE>, <&cru SRST_HDPTX0_ROPLL>,
+                 <&cru SRST_HDPTX0_LCPLL>;
+        reset-names = "phy", "apb", "init", "cmn", "lane", "ropll", "lcpll";
+        rockchip,grf = <&hdptxphy_grf>;
+      };
+    };

MAINTAINERS

@@ -13800,6 +13800,13 @@ F:	Documentation/devicetree/bindings/media/mediatek-vpu.txt
 F:	drivers/media/platform/mediatek/vcodec/
 F:	drivers/media/platform/mediatek/vpu/
 
+MEDIATEK MIPI-CSI CDPHY DRIVER
+M:	Julien Stephan <jstephan@baylibre.com>
+M:	Andy Hsieh <andy.hsieh@mediatek.com>
+S:	Supported
+F:	Documentation/devicetree/bindings/phy/mediatek,mt8365-csi-rx.yaml
+F:	drivers/phy/mediatek/phy-mtk-mipi-csi-0-5*
+
 MEDIATEK MMC/SD/SDIO DRIVER
 M:	Chaotian Jing <chaotian.jing@mediatek.com>
 S:	Maintained

drivers/phy/allwinner/phy-sun4i-usb.c

@@ -683,7 +683,7 @@ static int sun4i_usb_phy0_vbus_notify(struct notifier_block *nb,
 }
 
 static struct phy *sun4i_usb_phy_xlate(struct device *dev,
-					struct of_phandle_args *args)
+					const struct of_phandle_args *args)
 {
 	struct sun4i_usb_phy_data *data = dev_get_drvdata(dev);
 

drivers/phy/amlogic/phy-meson-g12a-usb3-pcie.c

@@ -350,7 +350,7 @@ static int phy_g12a_usb3_pcie_exit(struct phy *phy)
 }
 
 static struct phy *phy_g12a_usb3_pcie_xlate(struct device *dev,
-					    struct of_phandle_args *args)
+					    const struct of_phandle_args *args)
 {
 	struct phy_g12a_usb3_pcie_priv *priv = dev_get_drvdata(dev);
 	unsigned int mode;

drivers/phy/broadcom/phy-bcm-sr-pcie.c

@@ -195,7 +195,7 @@ static const struct phy_ops sr_paxc_phy_ops = {
 };
 
 static struct phy *sr_pcie_phy_xlate(struct device *dev,
-				     struct of_phandle_args *args)
+				     const struct of_phandle_args *args)
 {
 	struct sr_pcie_phy_core *core;
 	int phy_idx;

drivers/phy/broadcom/phy-bcm-sr-usb.c

@@ -209,7 +209,7 @@ static const struct phy_ops sr_phy_ops = {
 };
 
 static struct phy *bcm_usb_phy_xlate(struct device *dev,
-				     struct of_phandle_args *args)
+				     const struct of_phandle_args *args)
 {
 	struct bcm_usb_phy_cfg *phy_cfg;
 	int phy_idx;

drivers/phy/broadcom/phy-bcm63xx-usbh.c

@@ -366,7 +366,7 @@ static const struct phy_ops bcm63xx_usbh_phy_ops = {
 };
 
 static struct phy *bcm63xx_usbh_phy_xlate(struct device *dev,
-					  struct of_phandle_args *args)
+					  const struct of_phandle_args *args)
 {
 	struct bcm63xx_usbh_phy *usbh = dev_get_drvdata(dev);
 

drivers/phy/broadcom/phy-brcm-usb.c

@@ -175,7 +175,7 @@ static const struct phy_ops brcm_usb_phy_ops = {
 };
 
 static struct phy *brcm_usb_phy_xlate(struct device *dev,
-				      struct of_phandle_args *args)
+				      const struct of_phandle_args *args)
 {
 	struct brcm_usb_phy_data *data = dev_get_drvdata(dev);
 

drivers/phy/freescale/phy-fsl-imx8qm-lvds-phy.c

@@ -294,7 +294,7 @@ static int mixel_lvds_phy_reset(struct device *dev)
 }
 
 static struct phy *mixel_lvds_phy_xlate(struct device *dev,
-					struct of_phandle_args *args)
+					const struct of_phandle_args *args)
 {
 	struct mixel_lvds_phy_priv *priv = dev_get_drvdata(dev);
 	unsigned int phy_id;

drivers/phy/freescale/phy-fsl-lynx-28g.c

@@ -556,7 +556,7 @@ static void lynx_28g_lane_read_configuration(struct lynx_28g_lane *lane)
 }
 
 static struct phy *lynx_28g_xlate(struct device *dev,
-				  struct of_phandle_args *args)
+				  const struct of_phandle_args *args)
 {
 	struct lynx_28g_priv *priv = dev_get_drvdata(dev);
 	int idx = args->args[0];

drivers/phy/hisilicon/phy-histb-combphy.c

@@ -163,7 +163,7 @@ static const struct phy_ops histb_combphy_ops = {
 };
 
 static struct phy *histb_combphy_xlate(struct device *dev,
-				       struct of_phandle_args *args)
+				       const struct of_phandle_args *args)
 {
 	struct histb_combphy_priv *priv = dev_get_drvdata(dev);
 	struct histb_combphy_mode *mode = &priv->mode;

drivers/phy/intel/phy-intel-lgm-combo.c

@@ -508,7 +508,7 @@ static const struct phy_ops intel_cbphy_ops = {
 };
 
 static struct phy *intel_cbphy_xlate(struct device *dev,
-				     struct of_phandle_args *args)
+				     const struct of_phandle_args *args)
 {
 	struct intel_combo_phy *cbphy = dev_get_drvdata(dev);
 	u32 iphy_id;

drivers/phy/lantiq/phy-lantiq-vrx200-pcie.c

@@ -358,7 +358,7 @@ static const struct phy_ops ltq_vrx200_pcie_phy_ops = {
 };
 
 static struct phy *ltq_vrx200_pcie_phy_xlate(struct device *dev,
-					     struct of_phandle_args *args)
+					     const struct of_phandle_args *args)
 {
 	struct ltq_vrx200_pcie_phy_priv *priv = dev_get_drvdata(dev);
 	unsigned int mode;

drivers/phy/marvell/phy-armada375-usb2.c

@@ -61,7 +61,7 @@ static const struct phy_ops armada375_usb_phy_ops = {
  * USB3 case it still optional and we use ENODEV.
  */
 static struct phy *armada375_usb_phy_xlate(struct device *dev,
-					struct of_phandle_args *args)
+					const struct of_phandle_args *args)
 {
 	struct armada375_cluster_phy *cluster_phy = dev_get_drvdata(dev);
 

drivers/phy/marvell/phy-armada38x-comphy.c

@@ -47,8 +47,13 @@ struct a38x_comphy {
 	struct a38x_comphy_lane lane[MAX_A38X_COMPHY];
 };
 
+/*
+ * Map serdes lanes and gbe ports to serdes mux configuration values:
+ * row index = serdes lane,
+ * column index = gbe port number.
+ */
 static const u8 gbe_mux[MAX_A38X_COMPHY][MAX_A38X_PORTS] = {
-	{ 0, 0, 0 },
+	{ 3, 0, 0 },
 	{ 4, 5, 0 },
 	{ 0, 4, 0 },
 	{ 0, 0, 4 },
@@ -155,7 +160,7 @@ static const struct phy_ops a38x_comphy_ops = {
 };
 
 static struct phy *a38x_comphy_xlate(struct device *dev,
-				     struct of_phandle_args *args)
+				     const struct of_phandle_args *args)
 {
 	struct a38x_comphy_lane *lane;
 	struct phy *phy;

drivers/phy/marvell/phy-berlin-sata.c

@@ -155,7 +155,7 @@ static int phy_berlin_sata_power_off(struct phy *phy)
 }
 
 static struct phy *phy_berlin_sata_phy_xlate(struct device *dev,
-					     struct of_phandle_args *args)
+					     const struct of_phandle_args *args)
 {
 	struct phy_berlin_priv *priv = dev_get_drvdata(dev);
 	int i;

drivers/phy/marvell/phy-mvebu-a3700-comphy.c

@@ -1213,7 +1213,7 @@ static const struct phy_ops mvebu_a3700_comphy_ops = {
 };
 
 static struct phy *mvebu_a3700_comphy_xlate(struct device *dev,
-					    struct of_phandle_args *args)
+					    const struct of_phandle_args *args)
 {
 	struct mvebu_a3700_comphy_lane *lane;
 	unsigned int port;

drivers/phy/marvell/phy-mvebu-cp110-comphy.c

@@ -917,7 +917,7 @@ static const struct phy_ops mvebu_comphy_ops = {
 };
 
 static struct phy *mvebu_comphy_xlate(struct device *dev,
-				      struct of_phandle_args *args)
+				      const struct of_phandle_args *args)
 {
 	struct mvebu_comphy_lane *lane;
 	struct phy *phy;

drivers/phy/mediatek/Kconfig

@@ -58,6 +58,18 @@ config PHY_MTK_HDMI
 	help
 	  Support HDMI PHY for Mediatek SoCs.
 
+config PHY_MTK_MIPI_CSI_0_5
+	tristate "MediaTek MIPI CSI CD-PHY v0.5 Driver"
+	depends on ARCH_MEDIATEK || COMPILE_TEST
+	depends on OF
+	select GENERIC_PHY
+	help
+	  Enable this to support the MIPI CSI CD-PHY receiver version 0.5.
+	  The driver supports multiple CSI cdphy ports simultaneously.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called phy-mtk-mipi-csi-0-5.
+
 config PHY_MTK_MIPI_DSI
 	tristate "MediaTek MIPI-DSI Driver"
 	depends on ARCH_MEDIATEK || COMPILE_TEST

drivers/phy/mediatek/Makefile

@@ -15,6 +15,8 @@ phy-mtk-hdmi-drv-y			+= phy-mtk-hdmi-mt8173.o
 phy-mtk-hdmi-drv-y			+= phy-mtk-hdmi-mt8195.o
 obj-$(CONFIG_PHY_MTK_HDMI)		+= phy-mtk-hdmi-drv.o
 
+obj-$(CONFIG_PHY_MTK_MIPI_CSI_0_5)	+= phy-mtk-mipi-csi-0-5.o
+
 phy-mtk-mipi-dsi-drv-y			:= phy-mtk-mipi-dsi.o
 phy-mtk-mipi-dsi-drv-y			+= phy-mtk-mipi-dsi-mt8173.o
 phy-mtk-mipi-dsi-drv-y			+= phy-mtk-mipi-dsi-mt8183.o

drivers/phy/mediatek/phy-mtk-mipi-csi-0-5-rx-reg.h

+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (c) 2023, MediaTek Inc.
+ * Copyright (c) 2023, BayLibre Inc.
+ */
+
+#ifndef __PHY_MTK_MIPI_CSI_V_0_5_RX_REG_H__
+#define __PHY_MTK_MIPI_CSI_V_0_5_RX_REG_H__
+
+/*
+ * CSI1 and CSI2 are identical, and similar to CSI0. All CSIX macros are
+ * applicable to the three PHYs. Where differences exist, they are denoted by
+ * macro names using CSI0 and CSI1, the latter being applicable to CSI1 and
+ * CSI2 alike.
+ */
+
+#define MIPI_RX_ANA00_CSIXA			0x0000
+#define RG_CSI0A_CPHY_EN			BIT(0)
+#define RG_CSIXA_EQ_PROTECT_EN			BIT(1)
+#define RG_CSIXA_BG_LPF_EN			BIT(2)
+#define RG_CSIXA_BG_CORE_EN			BIT(3)
+#define RG_CSIXA_DPHY_L0_CKMODE_EN		BIT(5)
+#define RG_CSIXA_DPHY_L0_CKSEL			BIT(6)
+#define RG_CSIXA_DPHY_L1_CKMODE_EN		BIT(8)
+#define RG_CSIXA_DPHY_L1_CKSEL			BIT(9)
+#define RG_CSIXA_DPHY_L2_CKMODE_EN		BIT(11)
+#define RG_CSIXA_DPHY_L2_CKSEL			BIT(12)
+
+#define MIPI_RX_ANA18_CSIXA			0x0018
+#define RG_CSI0A_L0_T0AB_EQ_IS			GENMASK(5, 4)
+#define RG_CSI0A_L0_T0AB_EQ_BW			GENMASK(7, 6)
+#define RG_CSI0A_L1_T1AB_EQ_IS			GENMASK(21, 20)
+#define RG_CSI0A_L1_T1AB_EQ_BW			GENMASK(23, 22)
+#define RG_CSI0A_L2_T1BC_EQ_IS			GENMASK(21, 20)
+#define RG_CSI0A_L2_T1BC_EQ_BW			GENMASK(23, 22)
+#define RG_CSI1A_L0_EQ_IS			GENMASK(5, 4)
+#define RG_CSI1A_L0_EQ_BW			GENMASK(7, 6)
+#define RG_CSI1A_L1_EQ_IS			GENMASK(21, 20)
+#define RG_CSI1A_L1_EQ_BW			GENMASK(23, 22)
+#define RG_CSI1A_L2_EQ_IS			GENMASK(5, 4)
+#define RG_CSI1A_L2_EQ_BW			GENMASK(7, 6)
+
+#define MIPI_RX_ANA1C_CSIXA			0x001c
+#define MIPI_RX_ANA20_CSI0A			0x0020
+
+#define MIPI_RX_ANA24_CSIXA			0x0024
+#define RG_CSIXA_RESERVE			GENMASK(31, 24)
+
+#define MIPI_RX_ANA40_CSIXA			0x0040
+#define RG_CSIXA_CPHY_FMCK_SEL			GENMASK(1, 0)
+#define RG_CSIXA_ASYNC_OPTION			GENMASK(7, 4)
+#define RG_CSIXA_CPHY_SPARE			GENMASK(31, 16)
+
+#define MIPI_RX_WRAPPER80_CSIXA			0x0080
+#define CSR_CSI_RST_MODE			GENMASK(17, 16)
+
+#define MIPI_RX_ANAA8_CSIXA			0x00a8
+#define RG_CSIXA_CDPHY_L0_T0_BYTECK_INVERT	BIT(0)
+#define RG_CSIXA_DPHY_L1_BYTECK_INVERT		BIT(1)
+#define RG_CSIXA_CDPHY_L2_T1_BYTECK_INVERT	BIT(2)
+
+#endif

drivers/phy/mediatek/phy-mtk-mipi-csi-0-5.c

+// SPDX-License-Identifier: GPL-2.0
+/*
+ * MediaTek MIPI CSI v0.5 driver
+ *
+ * Copyright (c) 2023, MediaTek Inc.
+ * Copyright (c) 2023, BayLibre Inc.
+ */
+
+#include <dt-bindings/phy/phy.h>
+#include <linux/bitfield.h>
+#include <linux/delay.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/phy/phy.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+
+#include "phy-mtk-io.h"
+#include "phy-mtk-mipi-csi-0-5-rx-reg.h"
+
+#define CSIXB_OFFSET		0x1000
+
+struct mtk_mipi_cdphy_port {
+	struct device *dev;
+	void __iomem *base;
+	struct phy *phy;
+	u32 type;
+	u32 mode;
+	u32 num_lanes;
+};
+
+enum PHY_TYPE {
+	DPHY = 0,
+	CPHY,
+	CDPHY,
+};
+
+static void mtk_phy_csi_cdphy_ana_eq_tune(void __iomem *base)
+{
+	mtk_phy_update_field(base + MIPI_RX_ANA18_CSIXA, RG_CSI0A_L0_T0AB_EQ_IS, 1);
+	mtk_phy_update_field(base + MIPI_RX_ANA18_CSIXA, RG_CSI0A_L0_T0AB_EQ_BW, 1);
+	mtk_phy_update_field(base + MIPI_RX_ANA1C_CSIXA, RG_CSI0A_L1_T1AB_EQ_IS, 1);
+	mtk_phy_update_field(base + MIPI_RX_ANA1C_CSIXA, RG_CSI0A_L1_T1AB_EQ_BW, 1);
+	mtk_phy_update_field(base + MIPI_RX_ANA20_CSI0A, RG_CSI0A_L2_T1BC_EQ_IS, 1);
+	mtk_phy_update_field(base + MIPI_RX_ANA20_CSI0A, RG_CSI0A_L2_T1BC_EQ_BW, 1);
+
+	mtk_phy_update_field(base + CSIXB_OFFSET + MIPI_RX_ANA18_CSIXA, RG_CSI0A_L0_T0AB_EQ_IS, 1);
+	mtk_phy_update_field(base + CSIXB_OFFSET + MIPI_RX_ANA18_CSIXA, RG_CSI0A_L0_T0AB_EQ_BW, 1);
+	mtk_phy_update_field(base + CSIXB_OFFSET + MIPI_RX_ANA1C_CSIXA, RG_CSI0A_L1_T1AB_EQ_IS, 1);
+	mtk_phy_update_field(base + CSIXB_OFFSET + MIPI_RX_ANA1C_CSIXA, RG_CSI0A_L1_T1AB_EQ_BW, 1);
+	mtk_phy_update_field(base + CSIXB_OFFSET + MIPI_RX_ANA20_CSI0A, RG_CSI0A_L2_T1BC_EQ_IS, 1);
+	mtk_phy_update_field(base + CSIXB_OFFSET + MIPI_RX_ANA20_CSI0A, RG_CSI0A_L2_T1BC_EQ_BW, 1);
+}
+
+static void mtk_phy_csi_dphy_ana_eq_tune(void __iomem *base)
+{
+	mtk_phy_update_field(base + MIPI_RX_ANA18_CSIXA, RG_CSI1A_L0_EQ_IS, 1);
+	mtk_phy_update_field(base + MIPI_RX_ANA18_CSIXA, RG_CSI1A_L0_EQ_BW, 1);
+	mtk_phy_update_field(base + MIPI_RX_ANA18_CSIXA, RG_CSI1A_L1_EQ_IS, 1);
+	mtk_phy_update_field(base + MIPI_RX_ANA18_CSIXA, RG_CSI1A_L1_EQ_BW, 1);
+	mtk_phy_update_field(base + MIPI_RX_ANA1C_CSIXA, RG_CSI1A_L2_EQ_IS, 1);
+	mtk_phy_update_field(base + MIPI_RX_ANA1C_CSIXA, RG_CSI1A_L2_EQ_BW, 1);
+
+	mtk_phy_update_field(base + CSIXB_OFFSET + MIPI_RX_ANA18_CSIXA, RG_CSI1A_L0_EQ_IS, 1);
+	mtk_phy_update_field(base + CSIXB_OFFSET + MIPI_RX_ANA18_CSIXA, RG_CSI1A_L0_EQ_BW, 1);
+	mtk_phy_update_field(base + CSIXB_OFFSET + MIPI_RX_ANA18_CSIXA, RG_CSI1A_L1_EQ_IS, 1);
+	mtk_phy_update_field(base + CSIXB_OFFSET + MIPI_RX_ANA18_CSIXA, RG_CSI1A_L1_EQ_BW, 1);
+	mtk_phy_update_field(base + CSIXB_OFFSET + MIPI_RX_ANA1C_CSIXA, RG_CSI1A_L2_EQ_IS, 1);
+	mtk_phy_update_field(base + CSIXB_OFFSET + MIPI_RX_ANA1C_CSIXA, RG_CSI1A_L2_EQ_BW, 1);
+}
+
+static int mtk_mipi_phy_power_on(struct phy *phy)
+{
+	struct mtk_mipi_cdphy_port *port = phy_get_drvdata(phy);
+	void __iomem *base = port->base;
+
+	/*
+	 * The driver currently supports DPHY and CD-PHY phys,
+	 * but the only mode supported is DPHY,
+	 * so CD-PHY capable phys must be configured in DPHY mode
+	 */
+	if (port->type == CDPHY) {
+		mtk_phy_update_field(base + MIPI_RX_ANA00_CSIXA, RG_CSI0A_CPHY_EN, 0);
+		mtk_phy_update_field(base + CSIXB_OFFSET + MIPI_RX_ANA00_CSIXA,
+				     RG_CSI0A_CPHY_EN, 0);
+	}
+
+	/*
+	 * Lane configuration:
+	 *
+	 * Only 4 data + 1 clock is supported for now with the following mapping:
+	 *
+	 * CSIXA_LNR0 --> D2
+	 * CSIXA_LNR1 --> D0
+	 * CSIXA_LNR2 --> C
+	 * CSIXB_LNR0 --> D1
+	 * CSIXB_LNR1 --> D3
+	 */
+	mtk_phy_update_field(base + MIPI_RX_ANA00_CSIXA, RG_CSIXA_DPHY_L0_CKMODE_EN, 0);
+	mtk_phy_update_field(base + MIPI_RX_ANA00_CSIXA, RG_CSIXA_DPHY_L0_CKSEL, 1);
+	mtk_phy_update_field(base + MIPI_RX_ANA00_CSIXA, RG_CSIXA_DPHY_L1_CKMODE_EN, 0);
+	mtk_phy_update_field(base + MIPI_RX_ANA00_CSIXA, RG_CSIXA_DPHY_L1_CKSEL, 1);
+	mtk_phy_update_field(base + MIPI_RX_ANA00_CSIXA, RG_CSIXA_DPHY_L2_CKMODE_EN, 1);
+	mtk_phy_update_field(base + MIPI_RX_ANA00_CSIXA, RG_CSIXA_DPHY_L2_CKSEL, 1);
+
+	mtk_phy_update_field(base + CSIXB_OFFSET + MIPI_RX_ANA00_CSIXA,
+			     RG_CSIXA_DPHY_L0_CKMODE_EN, 0);
+	mtk_phy_update_field(base + CSIXB_OFFSET + MIPI_RX_ANA00_CSIXA, RG_CSIXA_DPHY_L0_CKSEL, 1);
+	mtk_phy_update_field(base + CSIXB_OFFSET + MIPI_RX_ANA00_CSIXA,
+			     RG_CSIXA_DPHY_L1_CKMODE_EN, 0);
+	mtk_phy_update_field(base + CSIXB_OFFSET + MIPI_RX_ANA00_CSIXA, RG_CSIXA_DPHY_L1_CKSEL, 1);
+	mtk_phy_update_field(base + CSIXB_OFFSET + MIPI_RX_ANA00_CSIXA,
+			     RG_CSIXA_DPHY_L2_CKMODE_EN, 0);
+	mtk_phy_update_field(base + CSIXB_OFFSET + MIPI_RX_ANA00_CSIXA, RG_CSIXA_DPHY_L2_CKSEL, 1);
+
+	/* Byte clock invert */
+	mtk_phy_update_field(base + MIPI_RX_ANAA8_CSIXA, RG_CSIXA_CDPHY_L0_T0_BYTECK_INVERT, 1);
+	mtk_phy_update_field(base + MIPI_RX_ANAA8_CSIXA, RG_CSIXA_DPHY_L1_BYTECK_INVERT, 1);
+	mtk_phy_update_field(base + MIPI_RX_ANAA8_CSIXA, RG_CSIXA_CDPHY_L2_T1_BYTECK_INVERT, 1);
+
+	mtk_phy_update_field(base + CSIXB_OFFSET + MIPI_RX_ANAA8_CSIXA,
+			     RG_CSIXA_CDPHY_L0_T0_BYTECK_INVERT, 1);
+	mtk_phy_update_field(base + CSIXB_OFFSET + MIPI_RX_ANAA8_CSIXA,
+			     RG_CSIXA_DPHY_L1_BYTECK_INVERT, 1);
+	mtk_phy_update_field(base + CSIXB_OFFSET + MIPI_RX_ANAA8_CSIXA,
+			     RG_CSIXA_CDPHY_L2_T1_BYTECK_INVERT, 1);
+
+	/* Start ANA EQ tuning */
+	if (port->type == CDPHY)
+		mtk_phy_csi_cdphy_ana_eq_tune(base);
+	else
+		mtk_phy_csi_dphy_ana_eq_tune(base);
+
+	/* End ANA EQ tuning */
+	mtk_phy_set_bits(base + MIPI_RX_ANA40_CSIXA, 0x90);
+
+	mtk_phy_update_field(base + MIPI_RX_ANA24_CSIXA, RG_CSIXA_RESERVE, 0x40);
+	mtk_phy_update_field(base + CSIXB_OFFSET + MIPI_RX_ANA24_CSIXA, RG_CSIXA_RESERVE, 0x40);
+	mtk_phy_update_field(base + MIPI_RX_WRAPPER80_CSIXA, CSR_CSI_RST_MODE, 0);
+	mtk_phy_update_field(base + CSIXB_OFFSET + MIPI_RX_WRAPPER80_CSIXA, CSR_CSI_RST_MODE, 0);
+	/* ANA power on */
+	mtk_phy_update_field(base + MIPI_RX_ANA00_CSIXA, RG_CSIXA_BG_CORE_EN, 1);
+	mtk_phy_update_field(base + CSIXB_OFFSET + MIPI_RX_ANA00_CSIXA, RG_CSIXA_BG_CORE_EN, 1);
+	usleep_range(20, 40);
+	mtk_phy_update_field(base + MIPI_RX_ANA00_CSIXA, RG_CSIXA_BG_LPF_EN, 1);
+	mtk_phy_update_field(base + CSIXB_OFFSET + MIPI_RX_ANA00_CSIXA, RG_CSIXA_BG_LPF_EN, 1);
+
+	return 0;
+}
+
+static int mtk_mipi_phy_power_off(struct phy *phy)
+{
+	struct mtk_mipi_cdphy_port *port = phy_get_drvdata(phy);
+	void __iomem *base = port->base;
+
+	/* Disable MIPI BG. */
+	mtk_phy_update_field(base + MIPI_RX_ANA00_CSIXA, RG_CSIXA_BG_CORE_EN, 0);
+	mtk_phy_update_field(base + MIPI_RX_ANA00_CSIXA, RG_CSIXA_BG_LPF_EN, 0);
+
+	mtk_phy_update_field(base + CSIXB_OFFSET + MIPI_RX_ANA00_CSIXA, RG_CSIXA_BG_CORE_EN, 0);
+	mtk_phy_update_field(base + CSIXB_OFFSET + MIPI_RX_ANA00_CSIXA, RG_CSIXA_BG_LPF_EN, 0);
+
+	return 0;
+}
+
+static struct phy *mtk_mipi_cdphy_xlate(struct device *dev,
+					const struct of_phandle_args *args)
+{
+	struct mtk_mipi_cdphy_port *priv = dev_get_drvdata(dev);
+
+	/*
+	 * If PHY is CD-PHY then we need to get the operating mode
+	 * For now only D-PHY mode is supported
+	 */
+	if (priv->type == CDPHY) {
+		if (args->args_count != 1) {
+			dev_err(dev, "invalid number of arguments\n");
+			return ERR_PTR(-EINVAL);
+		}
+		switch (args->args[0]) {
+		case PHY_TYPE_DPHY:
+			priv->mode = DPHY;
+			if (priv->num_lanes != 4) {
+				dev_err(dev, "Only 4D1C mode is supported for now!\n");
+				return ERR_PTR(-EINVAL);
+			}
+			break;
+		default:
+			dev_err(dev, "Unsupported PHY type: %i\n", args->args[0]);
+			return ERR_PTR(-EINVAL);
+		}
+	} else {
+		if (args->args_count) {
+			dev_err(dev, "invalid number of arguments\n");
+			return ERR_PTR(-EINVAL);
+		}
+		priv->mode = DPHY;
+	}
+
+	return priv->phy;
+}
+
+static const struct phy_ops mtk_cdphy_ops = {
+	.power_on	= mtk_mipi_phy_power_on,
+	.power_off	= mtk_mipi_phy_power_off,
+	.owner		= THIS_MODULE,
+};
+
+static int mtk_mipi_cdphy_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct phy_provider *phy_provider;
+	struct mtk_mipi_cdphy_port *port;
+	struct phy *phy;
+	int ret;
+	u32 phy_type;
+
+	port = devm_kzalloc(dev, sizeof(*port), GFP_KERNEL);
+	if (!port)
+		return -ENOMEM;
+
+	dev_set_drvdata(dev, port);
+
+	port->dev = dev;
+
+	port->base = devm_platform_ioremap_resource(pdev, 0);
+	if (IS_ERR(port->base))
+		return PTR_ERR(port->base);
+
+	ret = of_property_read_u32(dev->of_node, "num-lanes", &port->num_lanes);
+	if (ret) {
+		dev_err(dev, "Failed to read num-lanes property: %i\n", ret);
+		return ret;
+	}
+
+	/*
+	 * phy-type is optional, if not present, PHY is considered to be CD-PHY
+	 */
+	if (device_property_present(dev, "phy-type")) {
+		ret = of_property_read_u32(dev->of_node, "phy-type", &phy_type);
+		if (ret) {
+			dev_err(dev, "Failed to read phy-type property: %i\n", ret);
+			return ret;
+		}
+		switch (phy_type) {
+		case PHY_TYPE_DPHY:
+			port->type = DPHY;
+			break;
+		default:
+			dev_err(dev, "Unsupported PHY type: %i\n", phy_type);
+			return -EINVAL;
+		}
+	} else {
+		port->type = CDPHY;
+	}
+
+	phy = devm_phy_create(dev, NULL, &mtk_cdphy_ops);
+	if (IS_ERR(phy)) {
+		dev_err(dev, "Failed to create PHY: %ld\n", PTR_ERR(phy));
+		return PTR_ERR(phy);
+	}
+
+	port->phy = phy;
+	phy_set_drvdata(phy, port);
+
+	phy_provider = devm_of_phy_provider_register(dev, mtk_mipi_cdphy_xlate);
+	if (IS_ERR(phy_provider)) {
+		dev_err(dev, "Failed to register PHY provider: %ld\n",
+			PTR_ERR(phy_provider));
+		return PTR_ERR(phy_provider);
+	}
+
+	return 0;
+}
+
+static const struct of_device_id mtk_mipi_cdphy_of_match[] = {
+	{ .compatible = "mediatek,mt8365-csi-rx" },
+	{ /* sentinel */},
+};
+MODULE_DEVICE_TABLE(of, mtk_mipi_cdphy_of_match);
+
+static struct platform_driver mipi_cdphy_pdrv = {
+	.probe = mtk_mipi_cdphy_probe,
+	.driver	= {
+		.name	= "mtk-mipi-csi-0-5",
+		.of_match_table = mtk_mipi_cdphy_of_match,
+	},
+};
+module_platform_driver(mipi_cdphy_pdrv);
+
+MODULE_DESCRIPTION("MediaTek MIPI CSI CD-PHY v0.5 Driver");
+MODULE_AUTHOR("Louis Kuo <louis.kuo@mediatek.com>");
+MODULE_LICENSE("GPL");

drivers/phy/mediatek/phy-mtk-tphy.c

@@ -1467,7 +1467,7 @@ static int mtk_phy_set_mode(struct phy *phy, enum phy_mode mode, int submode)
 }
 
 static struct phy *mtk_phy_xlate(struct device *dev,
-					struct of_phandle_args *args)
+					const struct of_phandle_args *args)
 {
 	struct mtk_tphy *tphy = dev_get_drvdata(dev);
 	struct mtk_phy_instance *instance = NULL;

drivers/phy/mediatek/phy-mtk-xsphy.c

@@ -378,7 +378,7 @@ static int mtk_phy_set_mode(struct phy *phy, enum phy_mode mode, int submode)
 }
 
 static struct phy *mtk_phy_xlate(struct device *dev,
-				 struct of_phandle_args *args)
+				 const struct of_phandle_args *args)
 {
 	struct mtk_xsphy *xsphy = dev_get_drvdata(dev);
 	struct xsphy_instance *inst = NULL;

drivers/phy/microchip/lan966x_serdes.c

@@ -518,7 +518,7 @@ static const struct phy_ops serdes_ops = {
 };
 
 static struct phy *serdes_simple_xlate(struct device *dev,
-				       struct of_phandle_args *args)
+				       const struct of_phandle_args *args)
 {
 	struct serdes_ctrl *ctrl = dev_get_drvdata(dev);
 	unsigned int port, idx, i;

drivers/phy/microchip/sparx5_serdes.c

@@ -2509,7 +2509,7 @@ static struct sparx5_serdes_io_resource sparx5_serdes_iomap[] =  {
 
 /* Client lookup function, uses serdes index */
 static struct phy *sparx5_serdes_xlate(struct device *dev,
-				     struct of_phandle_args *args)
+				     const struct of_phandle_args *args)
 {
 	struct sparx5_serdes_private *priv = dev_get_drvdata(dev);
 	int idx;

drivers/phy/mscc/phy-ocelot-serdes.c

@@ -441,7 +441,7 @@ static const struct phy_ops serdes_ops = {
 };
 
 static struct phy *serdes_simple_xlate(struct device *dev,
-				       struct of_phandle_args *args)
+				       const struct of_phandle_args *args)
 {
 	struct serdes_ctrl *ctrl = dev_get_drvdata(dev);
 	unsigned int port, idx, i;

drivers/phy/phy-core.c

@@ -700,8 +700,8 @@ EXPORT_SYMBOL_GPL(devm_phy_put);
  * should provide a custom of_xlate function that reads the *args* and returns
  * the appropriate phy.
  */
-struct phy *of_phy_simple_xlate(struct device *dev, struct of_phandle_args
-	*args)
+struct phy *of_phy_simple_xlate(struct device *dev,
+				const struct of_phandle_args *args)
 {
 	struct phy *phy;
 	struct class_dev_iter iter;
@@ -1095,7 +1095,7 @@ EXPORT_SYMBOL_GPL(devm_phy_destroy);
 struct phy_provider *__of_phy_provider_register(struct device *dev,
 	struct device_node *children, struct module *owner,
 	struct phy * (*of_xlate)(struct device *dev,
-				 struct of_phandle_args *args))
+				 const struct of_phandle_args *args))
 {
 	struct phy_provider *phy_provider;
 
@@ -1158,7 +1158,7 @@ EXPORT_SYMBOL_GPL(__of_phy_provider_register);
 struct phy_provider *__devm_of_phy_provider_register(struct device *dev,
 	struct device_node *children, struct module *owner,
 	struct phy * (*of_xlate)(struct device *dev,
-				 struct of_phandle_args *args))
+				 const struct of_phandle_args *args))
 {
 	struct phy_provider **ptr, *phy_provider;
 

drivers/phy/phy-xgene.c

@@ -1611,7 +1611,7 @@ static const struct phy_ops xgene_phy_ops = {
 };
 
 static struct phy *xgene_phy_xlate(struct device *dev,
-				   struct of_phandle_args *args)
+				   const struct of_phandle_args *args)
 {
 	struct xgene_phy_ctx *ctx = dev_get_drvdata(dev);
 

drivers/phy/qualcomm/Makefile

@@ -7,7 +7,7 @@ obj-$(CONFIG_PHY_QCOM_IPQ806X_SATA)	+= phy-qcom-ipq806x-sata.o
 obj-$(CONFIG_PHY_QCOM_M31_USB)		+= phy-qcom-m31.o
 obj-$(CONFIG_PHY_QCOM_PCIE2)		+= phy-qcom-pcie2.o
 
-obj-$(CONFIG_PHY_QCOM_QMP_COMBO)	+= phy-qcom-qmp-combo.o
+obj-$(CONFIG_PHY_QCOM_QMP_COMBO)	+= phy-qcom-qmp-combo.o phy-qcom-qmp-usbc.o
 obj-$(CONFIG_PHY_QCOM_QMP_PCIE)		+= phy-qcom-qmp-pcie.o
 obj-$(CONFIG_PHY_QCOM_QMP_PCIE_8996)	+= phy-qcom-qmp-pcie-msm8996.o
 obj-$(CONFIG_PHY_QCOM_QMP_UFS)		+= phy-qcom-qmp-ufs.o

drivers/phy/qualcomm/phy-qcom-edp.c

@@ -21,7 +21,8 @@
 
 #include <dt-bindings/phy/phy.h>
 
-#include "phy-qcom-qmp.h"
+#include "phy-qcom-qmp-dp-phy.h"
+#include "phy-qcom-qmp-qserdes-com-v4.h"
 
 /* EDP_PHY registers */
 #define DP_PHY_CFG                              0x0010

drivers/phy/qualcomm/phy-qcom-qmp-combo.c

@@ -25,21 +25,21 @@
 
 #include <dt-bindings/phy/phy-qcom-qmp.h>
 
+#include "phy-qcom-qmp-common.h"
+
 #include "phy-qcom-qmp.h"
 #include "phy-qcom-qmp-pcs-misc-v3.h"
 #include "phy-qcom-qmp-pcs-usb-v4.h"
 #include "phy-qcom-qmp-pcs-usb-v5.h"
 #include "phy-qcom-qmp-pcs-usb-v6.h"
 
-/* QPHY_SW_RESET bit */
-#define SW_RESET				BIT(0)
-/* QPHY_POWER_DOWN_CONTROL */
-#define SW_PWRDN				BIT(0)
-/* QPHY_START_CONTROL bits */
-#define SERDES_START				BIT(0)
-#define PCS_START				BIT(1)
-/* QPHY_PCS_STATUS bit */
-#define PHYSTATUS				BIT(6)
+#include "phy-qcom-qmp-dp-com-v3.h"
+
+#include "phy-qcom-qmp-dp-phy.h"
+#include "phy-qcom-qmp-dp-phy-v3.h"
+#include "phy-qcom-qmp-dp-phy-v4.h"
+#include "phy-qcom-qmp-dp-phy-v5.h"
+#include "phy-qcom-qmp-dp-phy-v6.h"
 
 /* QPHY_V3_DP_COM_RESET_OVRD_CTRL register bits */
 /* DP PHY soft reset */
@@ -55,47 +55,12 @@
 #define USB3_MODE				BIT(0) /* enables USB3 mode */
 #define DP_MODE					BIT(1) /* enables DP mode */
 
-/* QPHY_PCS_AUTONOMOUS_MODE_CTRL register bits */
-#define ARCVR_DTCT_EN				BIT(0)
-#define ALFPS_DTCT_EN				BIT(1)
-#define ARCVR_DTCT_EVENT_SEL			BIT(4)
-
-/* QPHY_PCS_LFPS_RXTERM_IRQ_CLEAR register bits */
-#define IRQ_CLEAR				BIT(0)
-
-/* QPHY_V3_PCS_MISC_CLAMP_ENABLE register bits */
-#define CLAMP_EN				BIT(0) /* enables i/o clamp_n */
-
 /* QPHY_V3_DP_COM_TYPEC_CTRL register bits */
 #define SW_PORTSELECT_VAL			BIT(0)
 #define SW_PORTSELECT_MUX			BIT(1)
 
 #define PHY_INIT_COMPLETE_TIMEOUT		10000
 
-struct qmp_phy_init_tbl {
-	unsigned int offset;
-	unsigned int val;
-	/*
-	 * mask of lanes for which this register is written
-	 * for cases when second lane needs different values
-	 */
-	u8 lane_mask;
-};
-
-#define QMP_PHY_INIT_CFG(o, v)		\
-	{				\
-		.offset = o,		\
-		.val = v,		\
-		.lane_mask = 0xff,	\
-	}
-
-#define QMP_PHY_INIT_CFG_LANE(o, v, l)	\
-	{				\
-		.offset = o,		\
-		.val = v,		\
-		.lane_mask = l,		\
-	}
-
 /* set of registers with offsets different per-PHY */
 enum qphy_reg_layout {
 	/* PCS registers */
@@ -2031,55 +1996,29 @@ static const struct qmp_phy_cfg sm8550_usb3dpphy_cfg = {
 	.num_vregs		= ARRAY_SIZE(qmp_phy_vreg_l),
 };
 
-static void qmp_combo_configure_lane(void __iomem *base,
-					const struct qmp_phy_init_tbl tbl[],
-					int num,
-					u8 lane_mask)
-{
-	int i;
-	const struct qmp_phy_init_tbl *t = tbl;
-
-	if (!t)
-		return;
-
-	for (i = 0; i < num; i++, t++) {
-		if (!(t->lane_mask & lane_mask))
-			continue;
-
-		writel(t->val, base + t->offset);
-	}
-}
-
-static void qmp_combo_configure(void __iomem *base,
-				   const struct qmp_phy_init_tbl tbl[],
-				   int num)
-{
-	qmp_combo_configure_lane(base, tbl, num, 0xff);
-}
-
 static int qmp_combo_dp_serdes_init(struct qmp_combo *qmp)
 {
 	const struct qmp_phy_cfg *cfg = qmp->cfg;
 	void __iomem *serdes = qmp->dp_serdes;
 	const struct phy_configure_opts_dp *dp_opts = &qmp->dp_opts;
 
-	qmp_combo_configure(serdes, cfg->dp_serdes_tbl, cfg->dp_serdes_tbl_num);
+	qmp_configure(serdes, cfg->dp_serdes_tbl, cfg->dp_serdes_tbl_num);
 
 	switch (dp_opts->link_rate) {
 	case 1620:
-		qmp_combo_configure(serdes, cfg->serdes_tbl_rbr,
+		qmp_configure(serdes, cfg->serdes_tbl_rbr,
 				cfg->serdes_tbl_rbr_num);
 		break;
 	case 2700:
-		qmp_combo_configure(serdes, cfg->serdes_tbl_hbr,
+		qmp_configure(serdes, cfg->serdes_tbl_hbr,
 				cfg->serdes_tbl_hbr_num);
 		break;
 	case 5400:
-		qmp_combo_configure(serdes, cfg->serdes_tbl_hbr2,
+		qmp_configure(serdes, cfg->serdes_tbl_hbr2,
 				cfg->serdes_tbl_hbr2_num);
 		break;
 	case 8100:
-		qmp_combo_configure(serdes, cfg->serdes_tbl_hbr3,
+		qmp_configure(serdes, cfg->serdes_tbl_hbr3,
 				cfg->serdes_tbl_hbr3_num);
 		break;
 	default:
@@ -2370,7 +2309,7 @@ static int qmp_v456_configure_dp_phy(struct qmp_combo *qmp)
 	u32 status;
 	int ret;
 
-	writel(0x0f, qmp->dp_dp_phy + QSERDES_V4_DP_PHY_CFG_1);
+	writel(0x0f, qmp->dp_dp_phy + QSERDES_DP_PHY_CFG_1);
 
 	qmp_combo_configure_dp_mode(qmp);
 
@@ -2681,8 +2620,8 @@ static int qmp_combo_dp_power_on(struct phy *phy)
 
 	qmp_combo_dp_serdes_init(qmp);
 
-	qmp_combo_configure_lane(tx, cfg->dp_tx_tbl, cfg->dp_tx_tbl_num, 1);
-	qmp_combo_configure_lane(tx2, cfg->dp_tx_tbl, cfg->dp_tx_tbl_num, 2);
+	qmp_configure_lane(tx, cfg->dp_tx_tbl, cfg->dp_tx_tbl_num, 1);
+	qmp_configure_lane(tx2, cfg->dp_tx_tbl, cfg->dp_tx_tbl_num, 2);
 
 	/* Configure special DP tx tunings */
 	cfg->configure_dp_tx(qmp);
@@ -2724,7 +2663,7 @@ static int qmp_combo_usb_power_on(struct phy *phy)
 	unsigned int val;
 	int ret;
 
-	qmp_combo_configure(serdes, cfg->serdes_tbl, cfg->serdes_tbl_num);
+	qmp_configure(serdes, cfg->serdes_tbl, cfg->serdes_tbl_num);
 
 	ret = clk_prepare_enable(qmp->pipe_clk);
 	if (ret) {
@@ -2733,16 +2672,16 @@ static int qmp_combo_usb_power_on(struct phy *phy)
 	}
 
 	/* Tx, Rx, and PCS configurations */
-	qmp_combo_configure_lane(tx, cfg->tx_tbl, cfg->tx_tbl_num, 1);
-	qmp_combo_configure_lane(tx2, cfg->tx_tbl, cfg->tx_tbl_num, 2);
+	qmp_configure_lane(tx, cfg->tx_tbl, cfg->tx_tbl_num, 1);
+	qmp_configure_lane(tx2, cfg->tx_tbl, cfg->tx_tbl_num, 2);
 
-	qmp_combo_configure_lane(rx, cfg->rx_tbl, cfg->rx_tbl_num, 1);
-	qmp_combo_configure_lane(rx2, cfg->rx_tbl, cfg->rx_tbl_num, 2);
+	qmp_configure_lane(rx, cfg->rx_tbl, cfg->rx_tbl_num, 1);
+	qmp_configure_lane(rx2, cfg->rx_tbl, cfg->rx_tbl_num, 2);
 
-	qmp_combo_configure(pcs, cfg->pcs_tbl, cfg->pcs_tbl_num);
+	qmp_configure(pcs, cfg->pcs_tbl, cfg->pcs_tbl_num);
 
 	if (pcs_usb)
-		qmp_combo_configure(pcs_usb, cfg->pcs_usb_tbl, cfg->pcs_usb_tbl_num);
+		qmp_configure(pcs_usb, cfg->pcs_usb_tbl, cfg->pcs_usb_tbl_num);
 
 	if (cfg->has_pwrdn_delay)
 		usleep_range(10, 20);
@@ -3515,7 +3454,7 @@ static int qmp_combo_parse_dt(struct qmp_combo *qmp)
 	return 0;
 }
 
-static struct phy *qmp_combo_phy_xlate(struct device *dev, struct of_phandle_args *args)
+static struct phy *qmp_combo_phy_xlate(struct device *dev, const struct of_phandle_args *args)
 {
 	struct qmp_combo *qmp = dev_get_drvdata(dev);
 

drivers/phy/qualcomm/phy-qcom-qmp-common.h

+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (c) 2017, The Linux Foundation. All rights reserved.
+ */
+
+#ifndef QCOM_PHY_QMP_COMMON_H_
+#define QCOM_PHY_QMP_COMMON_H_
+
+struct qmp_phy_init_tbl {
+	unsigned int offset;
+	unsigned int val;
+	/*
+	 * mask of lanes for which this register is written
+	 * for cases when second lane needs different values
+	 */
+	u8 lane_mask;
+};
+
+#define QMP_PHY_INIT_CFG(o, v)		\
+	{				\
+		.offset = o,		\
+		.val = v,		\
+		.lane_mask = 0xff,	\
+	}
+
+#define QMP_PHY_INIT_CFG_LANE(o, v, l)	\
+	{				\
+		.offset = o,		\
+		.val = v,		\
+		.lane_mask = l,		\
+	}
+
+static inline void qmp_configure_lane(void __iomem *base,
+					   const struct qmp_phy_init_tbl tbl[],
+					   int num,
+					   u8 lane_mask)
+{
+	int i;
+	const struct qmp_phy_init_tbl *t = tbl;
+
+	if (!t)
+		return;
+
+	for (i = 0; i < num; i++, t++) {
+		if (!(t->lane_mask & lane_mask))
+			continue;
+
+		writel(t->val, base + t->offset);
+	}
+}
+
+static inline void qmp_configure(void __iomem *base,
+				      const struct qmp_phy_init_tbl tbl[],
+				      int num)
+{
+	qmp_configure_lane(base, tbl, num, 0xff);
+}
+
+#endif

drivers/phy/qualcomm/phy-qcom-qmp-dp-com-v3.h

+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (c) 2017, The Linux Foundation. All rights reserved.
+ */
+
+#ifndef QCOM_PHY_QMP_DP_COM_V3_H_
+#define QCOM_PHY_QMP_DP_COM_V3_H_
+
+/* Only for QMP V3 & V4 PHY - DP COM registers */
+#define QPHY_V3_DP_COM_PHY_MODE_CTRL			0x00
+#define QPHY_V3_DP_COM_SW_RESET				0x04
+#define QPHY_V3_DP_COM_POWER_DOWN_CTRL			0x08
+#define QPHY_V3_DP_COM_SWI_CTRL				0x0c
+#define QPHY_V3_DP_COM_TYPEC_CTRL			0x10
+#define QPHY_V3_DP_COM_TYPEC_PWRDN_CTRL			0x14
+#define QPHY_V3_DP_COM_RESET_OVRD_CTRL			0x1c
+
+#endif

drivers/phy/qualcomm/phy-qcom-qmp-dp-phy-v3.h

+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (c) 2017, The Linux Foundation. All rights reserved.
+ */
+
+#ifndef QCOM_PHY_QMP_DP_PHY_V3_H_
+#define QCOM_PHY_QMP_DP_PHY_V3_H_
+
+/* Only for QMP V3 PHY - DP PHY registers */
+#define QSERDES_V3_DP_PHY_AUX_INTERRUPT_MASK		0x048
+#define QSERDES_V3_DP_PHY_AUX_INTERRUPT_CLEAR		0x04c
+#define QSERDES_V3_DP_PHY_AUX_BIST_CFG			0x050
+
+#define QSERDES_V3_DP_PHY_VCO_DIV			0x064
+#define QSERDES_V3_DP_PHY_TX0_TX1_LANE_CTL		0x06c
+#define QSERDES_V3_DP_PHY_TX2_TX3_LANE_CTL		0x088
+
+#define QSERDES_V3_DP_PHY_SPARE0			0x0ac
+#define QSERDES_V3_DP_PHY_STATUS			0x0c0
+
+#endif

drivers/phy/qualcomm/phy-qcom-qmp-dp-phy-v4.h

+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (c) 2017, The Linux Foundation. All rights reserved.
+ */
+
+#ifndef QCOM_PHY_QMP_DP_PHY_V4_H_
+#define QCOM_PHY_QMP_DP_PHY_V4_H_
+
+/* Only for QMP V4 PHY - DP PHY registers */
+#define QSERDES_V4_DP_PHY_AUX_INTERRUPT_MASK		0x054
+#define QSERDES_V4_DP_PHY_AUX_INTERRUPT_CLEAR		0x058
+#define QSERDES_V4_DP_PHY_VCO_DIV			0x070
+#define QSERDES_V4_DP_PHY_TX0_TX1_LANE_CTL		0x078
+#define QSERDES_V4_DP_PHY_TX2_TX3_LANE_CTL		0x09c
+#define QSERDES_V4_DP_PHY_SPARE0			0x0c8
+#define QSERDES_V4_DP_PHY_AUX_INTERRUPT_STATUS		0x0d8
+#define QSERDES_V4_DP_PHY_STATUS			0x0dc
+
+#endif

drivers/phy/qualcomm/phy-qcom-qmp-dp-phy-v5.h

+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (c) 2017, The Linux Foundation. All rights reserved.
+ */
+
+#ifndef QCOM_PHY_QMP_DP_PHY_V5_H_
+#define QCOM_PHY_QMP_DP_PHY_V5_H_
+
+/* Only for QMP V5 PHY - DP PHY registers */
+#define QSERDES_V5_DP_PHY_AUX_INTERRUPT_STATUS		0x0d8
+#define QSERDES_V5_DP_PHY_STATUS			0x0dc
+
+#endif

drivers/phy/qualcomm/phy-qcom-qmp-dp-phy-v6.h

+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (c) 2017, The Linux Foundation. All rights reserved.
+ */
+
+#ifndef QCOM_PHY_QMP_DP_PHY_V6_H_
+#define QCOM_PHY_QMP_DP_PHY_V6_H_
+
+/* Only for QMP V6 PHY - DP PHY registers */
+#define QSERDES_V6_DP_PHY_AUX_INTERRUPT_STATUS		0x0e0
+#define QSERDES_V6_DP_PHY_STATUS			0x0e4
+
+#endif

drivers/phy/qualcomm/phy-qcom-qmp-dp-phy.h

+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (c) 2017, The Linux Foundation. All rights reserved.
+ */
+
+#ifndef QCOM_PHY_QMP_DP_PHY_H_
+#define QCOM_PHY_QMP_DP_PHY_H_
+
+/* QMP PHY - DP PHY registers */
+#define QSERDES_DP_PHY_REVISION_ID0			0x000
+#define QSERDES_DP_PHY_REVISION_ID1			0x004
+#define QSERDES_DP_PHY_REVISION_ID2			0x008
+#define QSERDES_DP_PHY_REVISION_ID3			0x00c
+#define QSERDES_DP_PHY_CFG				0x010
+#define QSERDES_DP_PHY_CFG_1				0x014
+#define QSERDES_DP_PHY_PD_CTL				0x018
+#define QSERDES_DP_PHY_MODE				0x01c
+#define QSERDES_DP_PHY_AUX_CFG0				0x020
+#define QSERDES_DP_PHY_AUX_CFG1				0x024
+#define QSERDES_DP_PHY_AUX_CFG2				0x028
+#define QSERDES_DP_PHY_AUX_CFG3				0x02c
+#define QSERDES_DP_PHY_AUX_CFG4				0x030
+#define QSERDES_DP_PHY_AUX_CFG5				0x034
+#define QSERDES_DP_PHY_AUX_CFG6				0x038
+#define QSERDES_DP_PHY_AUX_CFG7				0x03c
+#define QSERDES_DP_PHY_AUX_CFG8				0x040
+#define QSERDES_DP_PHY_AUX_CFG9				0x044
+
+/* QSERDES COM_BIAS_EN_CLKBUFLR_EN bits */
+# define QSERDES_V3_COM_BIAS_EN				0x0001
+# define QSERDES_V3_COM_BIAS_EN_MUX			0x0002
+# define QSERDES_V3_COM_CLKBUF_R_EN			0x0004
+# define QSERDES_V3_COM_CLKBUF_L_EN			0x0008
+# define QSERDES_V3_COM_EN_SYSCLK_TX_SEL		0x0010
+# define QSERDES_V3_COM_CLKBUF_RX_DRIVE_L		0x0020
+# define QSERDES_V3_COM_CLKBUF_RX_DRIVE_R		0x0040
+
+/* QPHY_TX_TX_EMP_POST1_LVL bits */
+# define DP_PHY_TXn_TX_EMP_POST1_LVL_MASK		0x001f
+# define DP_PHY_TXn_TX_EMP_POST1_LVL_MUX_EN		0x0020
+
+/* QPHY_TX_TX_DRV_LVL bits */
+# define DP_PHY_TXn_TX_DRV_LVL_MASK			0x001f
+# define DP_PHY_TXn_TX_DRV_LVL_MUX_EN			0x0020
+
+/* QSERDES_DP_PHY_PD_CTL bits */
+# define DP_PHY_PD_CTL_PWRDN				0x001
+# define DP_PHY_PD_CTL_PSR_PWRDN			0x002
+# define DP_PHY_PD_CTL_AUX_PWRDN			0x004
+# define DP_PHY_PD_CTL_LANE_0_1_PWRDN			0x008
+# define DP_PHY_PD_CTL_LANE_2_3_PWRDN			0x010
+# define DP_PHY_PD_CTL_PLL_PWRDN			0x020
+# define DP_PHY_PD_CTL_DP_CLAMP_EN			0x040
+
+/* QPHY_DP_PHY_AUX_INTERRUPT_STATUS bits */
+# define PHY_AUX_STOP_ERR_MASK				0x01
+# define PHY_AUX_DEC_ERR_MASK				0x02
+# define PHY_AUX_SYNC_ERR_MASK				0x04
+# define PHY_AUX_ALIGN_ERR_MASK				0x08
+# define PHY_AUX_REQ_ERR_MASK				0x10
+
+#endif

drivers/phy/qualcomm/phy-qcom-qmp-pcie-msm8996.c

@@ -19,19 +19,13 @@
 #include <linux/reset.h>
 #include <linux/slab.h>
 
+#include "phy-qcom-qmp-common.h"
+
 #include "phy-qcom-qmp.h"
 
-/* QPHY_SW_RESET bit */
-#define SW_RESET				BIT(0)
-/* QPHY_POWER_DOWN_CONTROL */
-#define SW_PWRDN				BIT(0)
-#define REFCLK_DRV_DSBL				BIT(1)
 /* QPHY_START_CONTROL bits */
-#define SERDES_START				BIT(0)
-#define PCS_START				BIT(1)
 #define PLL_READY_GATE_EN			BIT(3)
-/* QPHY_PCS_STATUS bit */
-#define PHYSTATUS				BIT(6)
+
 /* QPHY_COM_PCS_READY_STATUS bit */
 #define PCS_READY				BIT(0)
 
@@ -39,30 +33,6 @@
 #define POWER_DOWN_DELAY_US_MIN			10
 #define POWER_DOWN_DELAY_US_MAX			20
 
-struct qmp_phy_init_tbl {
-	unsigned int offset;
-	unsigned int val;
-	/*
-	 * mask of lanes for which this register is written
-	 * for cases when second lane needs different values
-	 */
-	u8 lane_mask;
-};
-
-#define QMP_PHY_INIT_CFG(o, v)		\
-	{				\
-		.offset = o,		\
-		.val = v,		\
-		.lane_mask = 0xff,	\
-	}
-
-#define QMP_PHY_INIT_CFG_LANE(o, v, l)	\
-	{				\
-		.offset = o,		\
-		.val = v,		\
-		.lane_mask = l,		\
-	}
-
 /* set of registers with offsets different per-PHY */
 enum qphy_reg_layout {
 	/* Common block control registers */
@@ -307,32 +277,6 @@ static const struct qmp_phy_cfg msm8996_pciephy_cfg = {
 	.regs			= pciephy_regs_layout,
 };
 
-static void qmp_pcie_msm8996_configure_lane(void __iomem *base,
-					const struct qmp_phy_init_tbl tbl[],
-					int num,
-					u8 lane_mask)
-{
-	int i;
-	const struct qmp_phy_init_tbl *t = tbl;
-
-	if (!t)
-		return;
-
-	for (i = 0; i < num; i++, t++) {
-		if (!(t->lane_mask & lane_mask))
-			continue;
-
-		writel(t->val, base + t->offset);
-	}
-}
-
-static void qmp_pcie_msm8996_configure(void __iomem *base,
-				   const struct qmp_phy_init_tbl tbl[],
-				   int num)
-{
-	qmp_pcie_msm8996_configure_lane(base, tbl, num, 0xff);
-}
-
 static int qmp_pcie_msm8996_serdes_init(struct qmp_phy *qphy)
 {
 	struct qcom_qmp *qmp = qphy->qmp;
@@ -344,7 +288,7 @@ static int qmp_pcie_msm8996_serdes_init(struct qmp_phy *qphy)
 	unsigned int val;
 	int ret;
 
-	qmp_pcie_msm8996_configure(serdes, serdes_tbl, serdes_tbl_num);
+	qmp_configure(serdes, serdes_tbl, serdes_tbl_num);
 
 	qphy_clrbits(serdes, cfg->regs[QPHY_COM_SW_RESET], SW_RESET);
 	qphy_setbits(serdes, cfg->regs[QPHY_COM_START_CONTROL],
@@ -487,9 +431,9 @@ static int qmp_pcie_msm8996_power_on(struct phy *phy)
 	}
 
 	/* Tx, Rx, and PCS configurations */
-	qmp_pcie_msm8996_configure_lane(tx, cfg->tx_tbl, cfg->tx_tbl_num, 1);
-	qmp_pcie_msm8996_configure_lane(rx, cfg->rx_tbl, cfg->rx_tbl_num, 1);
-	qmp_pcie_msm8996_configure(pcs, cfg->pcs_tbl, cfg->pcs_tbl_num);
+	qmp_configure_lane(tx, cfg->tx_tbl, cfg->tx_tbl_num, 1);
+	qmp_configure_lane(rx, cfg->rx_tbl, cfg->rx_tbl_num, 1);
+	qmp_configure(pcs, cfg->pcs_tbl, cfg->pcs_tbl_num);
 
 	/*
 	 * Pull out PHY from POWER DOWN state.

drivers/phy/qualcomm/phy-qcom-qmp-pcs-pcie-v6.h

@@ -7,6 +7,8 @@
 #define QCOM_PHY_QMP_PCS_PCIE_V6_H_
 
 /* Only for QMP V6 PHY - PCIE have different offsets than V5 */
+#define QPHY_PCIE_V6_PCS_PCIE_EQ_CONFIG1		0xa4
+#define QPHY_PCIE_V6_PCS_PCIE_RXEQEVAL_TIME		0xf4
 #define QPHY_PCIE_V6_PCS_PCIE_POWER_STATE_CONFIG2	0x0c
 #define QPHY_PCIE_V6_PCS_PCIE_POWER_STATE_CONFIG4	0x14
 #define QPHY_PCIE_V6_PCS_PCIE_ENDPOINT_REFCLK_DRIVE	0x20

drivers/phy/qualcomm/phy-qcom-qmp-pcs-pcie-v6_20.h

@@ -12,6 +12,8 @@
 #define QPHY_PCIE_V6_20_PCS_ENDPOINT_REFCLK_DRIVE	0x01c
 #define QPHY_PCIE_V6_20_PCS_OSC_DTCT_ATCIONS		0x090
 #define QPHY_PCIE_V6_20_PCS_EQ_CONFIG1			0x0a0
+#define QPHY_PCIE_V6_20_PCS_G3_RXEQEVAL_TIME		0x0f0
+#define QPHY_PCIE_V6_20_PCS_G4_RXEQEVAL_TIME		0x0f4
 #define QPHY_PCIE_V6_20_PCS_EQ_CONFIG5			0x108
 #define QPHY_PCIE_V6_20_PCS_G4_PRE_GAIN			0x15c
 #define QPHY_PCIE_V6_20_PCS_RX_MARGINING_CONFIG1	0x17c

drivers/phy/qualcomm/phy-qcom-qmp-pcs-sgmii.h

+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (c) 2023, Linaro Limited
+ */
+
+#ifndef QCOM_PHY_QMP_PCS_SGMII_H_
+#define QCOM_PHY_QMP_PCS_SGMII_H_
+
+#define QPHY_PCS_PHY_START				0x000
+#define QPHY_PCS_POWER_DOWN_CONTROL			0x004
+#define QPHY_PCS_SW_RESET				0x008
+#define QPHY_PCS_LINE_RESET_TIME			0x00c
+#define QPHY_PCS_TX_LARGE_AMP_DRV_LVL			0x020
+#define QPHY_PCS_TX_SMALL_AMP_DRV_LVL			0x028
+#define QPHY_PCS_PCS_READY_STATUS			0x094
+#define QPHY_PCS_TX_MID_TERM_CTRL1			0x0d8
+#define QPHY_PCS_TX_MID_TERM_CTRL2			0x0dc
+#define QPHY_PCS_SGMII_MISC_CTRL8			0x118
+
+#endif

drivers/phy/qualcomm/phy-qcom-qmp-pcs-ufs-v6.h

@@ -19,6 +19,7 @@
 #define QPHY_V6_PCS_UFS_BIST_FIXED_PAT_CTRL		0x060
 #define QPHY_V6_PCS_UFS_TX_HSGEAR_CAPABILITY		0x074
 #define QPHY_V6_PCS_UFS_RX_HSGEAR_CAPABILITY		0x0bc
+#define QPHY_V6_PCS_UFS_RX_HS_G5_SYNC_LENGTH_CAPABILITY	0x12c
 #define QPHY_V6_PCS_UFS_DEBUG_BUS_CLKSEL		0x158
 #define QPHY_V6_PCS_UFS_LINECFG_DISABLE			0x17c
 #define QPHY_V6_PCS_UFS_RX_MIN_HIBERN8_TIME		0x184
@@ -28,5 +29,6 @@
 #define QPHY_V6_PCS_UFS_READY_STATUS			0x1a8
 #define QPHY_V6_PCS_UFS_TX_MID_TERM_CTRL1		0x1f4
 #define QPHY_V6_PCS_UFS_MULTI_LANE_CTRL1		0x1fc
+#define QPHY_V6_PCS_UFS_RX_HSG5_SYNC_WAIT_TIME		0x220
 
 #endif

drivers/phy/qualcomm/phy-qcom-qmp-pcs-v6_20.h

@@ -7,6 +7,7 @@
 #define QCOM_PHY_QMP_PCS_V6_20_H_
 
 /* Only for QMP V6_20 PHY - USB/PCIe PCS registers */
+#define QPHY_V6_20_PCS_G12S1_TXDEEMPH_M6DB		0x170
 #define QPHY_V6_20_PCS_G3S2_PRE_GAIN			0x178
 #define QPHY_V6_20_PCS_RX_SIGDET_LVL			0x190
 #define QPHY_V6_20_PCS_COM_ELECIDLE_DLY_SEL		0x1b8

drivers/phy/qualcomm/phy-qcom-qmp-qserdes-com-v6.h

@@ -60,6 +60,8 @@
 #define QSERDES_V6_COM_SYSCLK_BUF_ENABLE			0xe8
 #define QSERDES_V6_COM_PLL_IVCO					0xf4
 #define QSERDES_V6_COM_PLL_IVCO_MODE1				0xf8
+#define QSERDES_V6_COM_CMN_IETRIM				0xfc
+#define QSERDES_V6_COM_CMN_IPTRIM				0x100
 #define QSERDES_V6_COM_SYSCLK_EN_SEL				0x110
 #define QSERDES_V6_COM_RESETSM_CNTRL				0x118
 #define QSERDES_V6_COM_LOCK_CMP_EN				0x120

drivers/phy/qualcomm/phy-qcom-qmp-qserdes-txrx-ufs-v6.h

@@ -15,13 +15,19 @@
 
 #define QSERDES_UFS_V6_RX_UCDR_FASTLOCK_FO_GAIN_RATE2		0x08
 #define QSERDES_UFS_V6_RX_UCDR_FASTLOCK_FO_GAIN_RATE4		0x10
+#define QSERDES_UFS_V6_RX_UCDR_FASTLOCK_SO_GAIN_RATE4		0x24
 #define QSERDES_UFS_V6_RX_UCDR_SO_SATURATION			0x28
+#define QSERDES_UFS_V6_RX_UCDR_FASTLOCK_COUNT_HIGH_RATE4	0x54
 #define QSERDES_UFS_V6_RX_UCDR_PI_CTRL1				0x58
 #define QSERDES_UFS_V6_RX_RX_TERM_BW_CTRL0			0xc4
 #define QSERDES_UFS_V6_RX_UCDR_FO_GAIN_RATE2			0xd4
 #define QSERDES_UFS_V6_RX_UCDR_FO_GAIN_RATE4			0xdc
+#define QSERDES_UFS_V6_RX_UCDR_SO_GAIN_RATE4			0xf0
+#define QSERDES_UFS_V6_RX_UCDR_PI_CONTROLS			0xf4
 #define QSERDES_UFS_V6_RX_VGA_CAL_MAN_VAL			0x178
+#define QSERDES_UFS_V6_RX_EQ_OFFSET_ADAPTOR_CNTRL1		0x1bc
 #define QSERDES_UFS_V6_RX_INTERFACE_MODE			0x1e0
+#define QSERDES_UFS_V6_RX_OFFSET_ADAPTOR_CNTRL3			0x1c4
 #define QSERDES_UFS_V6_RX_MODE_RATE_0_1_B0			0x208
 #define QSERDES_UFS_V6_RX_MODE_RATE_0_1_B1			0x20c
 #define QSERDES_UFS_V6_RX_MODE_RATE_0_1_B3			0x214
@@ -33,6 +39,8 @@
 #define QSERDES_UFS_V6_RX_MODE_RATE3_B5				0x264
 #define QSERDES_UFS_V6_RX_MODE_RATE3_B8				0x270
 #define QSERDES_UFS_V6_RX_MODE_RATE4_B3				0x280
+#define QSERDES_UFS_V6_RX_MODE_RATE4_B4				0x284
 #define QSERDES_UFS_V6_RX_MODE_RATE4_B6				0x28c
+#define QSERDES_UFS_V6_RX_DLL0_FTUNE_CTRL			0x2f8
 
 #endif

drivers/phy/qualcomm/phy-qcom-qmp-qserdes-txrx-v6_20.h

@@ -23,6 +23,8 @@
 #define QSERDES_V6_20_RX_DFE_1					0xac
 #define QSERDES_V6_20_RX_DFE_2					0xb0
 #define QSERDES_V6_20_RX_DFE_3					0xb4
+#define QSERDES_V6_20_RX_TX_ADPT_CTRL				0xd4
+#define QSERDES_V6_20_VGA_CAL_CNTRL1				0xe0
 #define QSERDES_V6_20_RX_VGA_CAL_MAN_VAL			0xe8
 #define QSERDES_V6_20_RX_GM_CAL					0x10c
 #define QSERDES_V6_20_RX_EQU_ADAPTOR_CNTRL4			0x120

drivers/phy/qualcomm/phy-qcom-qmp-usb-legacy.c

@@ -25,15 +25,7 @@
 #include "phy-qcom-qmp-pcs-usb-v4.h"
 #include "phy-qcom-qmp-pcs-usb-v5.h"
 
-/* QPHY_SW_RESET bit */
-#define SW_RESET				BIT(0)
-/* QPHY_POWER_DOWN_CONTROL */
-#define SW_PWRDN				BIT(0)
-/* QPHY_START_CONTROL bits */
-#define SERDES_START				BIT(0)
-#define PCS_START				BIT(1)
-/* QPHY_PCS_STATUS bit */
-#define PHYSTATUS				BIT(6)
+#include "phy-qcom-qmp-dp-com-v3.h"
 
 /* QPHY_V3_DP_COM_RESET_OVRD_CTRL register bits */
 /* DP PHY soft reset */
@@ -49,17 +41,6 @@
 #define USB3_MODE				BIT(0) /* enables USB3 mode */
 #define DP_MODE					BIT(1) /* enables DP mode */
 
-/* QPHY_PCS_AUTONOMOUS_MODE_CTRL register bits */
-#define ARCVR_DTCT_EN				BIT(0)
-#define ALFPS_DTCT_EN				BIT(1)
-#define ARCVR_DTCT_EVENT_SEL			BIT(4)
-
-/* QPHY_PCS_LFPS_RXTERM_IRQ_CLEAR register bits */
-#define IRQ_CLEAR				BIT(0)
-
-/* QPHY_V3_PCS_MISC_CLAMP_ENABLE register bits */
-#define CLAMP_EN				BIT(0) /* enables i/o clamp_n */
-
 #define PHY_INIT_COMPLETE_TIMEOUT		10000
 
 struct qmp_phy_init_tbl {
@@ -507,8 +488,6 @@ struct qmp_usb_legacy_offsets {
 
 /* struct qmp_phy_cfg - per-PHY initialization config */
 struct qmp_phy_cfg {
-	int lanes;
-
 	const struct qmp_usb_legacy_offsets *offsets;
 
 	/* Init sequence for PHY blocks - serdes, tx, rx, pcs */
@@ -621,8 +600,6 @@ static const char * const qmp_phy_vreg_l[] = {
 };
 
 static const struct qmp_phy_cfg qmp_v3_usb3phy_cfg = {
-	.lanes			= 2,
-
 	.serdes_tbl		= qmp_v3_usb3_serdes_tbl,
 	.serdes_tbl_num		= ARRAY_SIZE(qmp_v3_usb3_serdes_tbl),
 	.tx_tbl			= qmp_v3_usb3_tx_tbl,
@@ -641,8 +618,6 @@ static const struct qmp_phy_cfg qmp_v3_usb3phy_cfg = {
 };
 
 static const struct qmp_phy_cfg sc7180_usb3phy_cfg = {
-	.lanes			= 2,
-
 	.serdes_tbl		= qmp_v3_usb3_serdes_tbl,
 	.serdes_tbl_num		= ARRAY_SIZE(qmp_v3_usb3_serdes_tbl),
 	.tx_tbl			= qmp_v3_usb3_tx_tbl,
@@ -661,8 +636,6 @@ static const struct qmp_phy_cfg sc7180_usb3phy_cfg = {
 };
 
 static const struct qmp_phy_cfg sm8150_usb3phy_cfg = {
-	.lanes			= 2,
-
 	.serdes_tbl		= sm8150_usb3_serdes_tbl,
 	.serdes_tbl_num		= ARRAY_SIZE(sm8150_usb3_serdes_tbl),
 	.tx_tbl			= sm8150_usb3_tx_tbl,
@@ -684,8 +657,6 @@ static const struct qmp_phy_cfg sm8150_usb3phy_cfg = {
 };
 
 static const struct qmp_phy_cfg sm8250_usb3phy_cfg = {
-	.lanes			= 2,
-
 	.serdes_tbl		= sm8150_usb3_serdes_tbl,
 	.serdes_tbl_num		= ARRAY_SIZE(sm8150_usb3_serdes_tbl),
 	.tx_tbl			= sm8250_usb3_tx_tbl,
@@ -707,8 +678,6 @@ static const struct qmp_phy_cfg sm8250_usb3phy_cfg = {
 };
 
 static const struct qmp_phy_cfg sm8350_usb3phy_cfg = {
-	.lanes			= 2,
-
 	.serdes_tbl		= sm8150_usb3_serdes_tbl,
 	.serdes_tbl_num		= ARRAY_SIZE(sm8150_usb3_serdes_tbl),
 	.tx_tbl			= sm8350_usb3_tx_tbl,
@@ -874,10 +843,8 @@ static int qmp_usb_legacy_power_on(struct phy *phy)
 	qmp_usb_legacy_configure_lane(tx, cfg->tx_tbl, cfg->tx_tbl_num, 1);
 	qmp_usb_legacy_configure_lane(rx, cfg->rx_tbl, cfg->rx_tbl_num, 1);
 
-	if (cfg->lanes >= 2) {
-		qmp_usb_legacy_configure_lane(qmp->tx2, cfg->tx_tbl, cfg->tx_tbl_num, 2);
-		qmp_usb_legacy_configure_lane(qmp->rx2, cfg->rx_tbl, cfg->rx_tbl_num, 2);
-	}
+	qmp_usb_legacy_configure_lane(qmp->tx2, cfg->tx_tbl, cfg->tx_tbl_num, 2);
+	qmp_usb_legacy_configure_lane(qmp->rx2, cfg->rx_tbl, cfg->rx_tbl_num, 2);
 
 	qmp_usb_legacy_configure(pcs, cfg->pcs_tbl, cfg->pcs_tbl_num);
 
@@ -1180,27 +1147,11 @@ static int phy_pipe_clk_register(struct qmp_usb *qmp, struct device_node *np)
 	return devm_add_action_or_reset(qmp->dev, phy_clk_release_provider, np);
 }
 
-static void __iomem *qmp_usb_legacy_iomap(struct device *dev, struct device_node *np,
-					int index, bool exclusive)
-{
-	struct resource res;
-
-	if (!exclusive) {
-		if (of_address_to_resource(np, index, &res))
-			return IOMEM_ERR_PTR(-EINVAL);
-
-		return devm_ioremap(dev, res.start, resource_size(&res));
-	}
-
-	return devm_of_iomap(dev, np, index, NULL);
-}
-
 static int qmp_usb_legacy_parse_dt_legacy(struct qmp_usb *qmp, struct device_node *np)
 {
 	struct platform_device *pdev = to_platform_device(qmp->dev);
 	const struct qmp_phy_cfg *cfg = qmp->cfg;
 	struct device *dev = qmp->dev;
-	bool exclusive = true;
 
 	qmp->serdes = devm_platform_ioremap_resource(pdev, 0);
 	if (IS_ERR(qmp->serdes))
@@ -1224,27 +1175,22 @@ static int qmp_usb_legacy_parse_dt_legacy(struct qmp_usb *qmp, struct device_nod
 	if (IS_ERR(qmp->rx))
 		return PTR_ERR(qmp->rx);
 
-	qmp->pcs = qmp_usb_legacy_iomap(dev, np, 2, exclusive);
+	qmp->pcs = devm_of_iomap(dev, np, 2, NULL);
 	if (IS_ERR(qmp->pcs))
 		return PTR_ERR(qmp->pcs);
 
 	if (cfg->pcs_usb_offset)
 		qmp->pcs_usb = qmp->pcs + cfg->pcs_usb_offset;
 
-	if (cfg->lanes >= 2) {
-		qmp->tx2 = devm_of_iomap(dev, np, 3, NULL);
-		if (IS_ERR(qmp->tx2))
-			return PTR_ERR(qmp->tx2);
-
-		qmp->rx2 = devm_of_iomap(dev, np, 4, NULL);
-		if (IS_ERR(qmp->rx2))
-			return PTR_ERR(qmp->rx2);
+	qmp->tx2 = devm_of_iomap(dev, np, 3, NULL);
+	if (IS_ERR(qmp->tx2))
+		return PTR_ERR(qmp->tx2);
 
-		qmp->pcs_misc = devm_of_iomap(dev, np, 5, NULL);
-	} else {
-		qmp->pcs_misc = devm_of_iomap(dev, np, 3, NULL);
-	}
+	qmp->rx2 = devm_of_iomap(dev, np, 4, NULL);
+	if (IS_ERR(qmp->rx2))
+		return PTR_ERR(qmp->rx2);
 
+	qmp->pcs_misc = devm_of_iomap(dev, np, 5, NULL);
 	if (IS_ERR(qmp->pcs_misc)) {
 		dev_vdbg(dev, "PHY pcs_misc-reg not used\n");
 		qmp->pcs_misc = NULL;

drivers/phy/qualcomm/phy-qcom-qmp.h

@@ -50,92 +50,29 @@
 
 #include "phy-qcom-qmp-pcs-v7.h"
 
-/* Only for QMP V3 & V4 PHY - DP COM registers */
-#define QPHY_V3_DP_COM_PHY_MODE_CTRL			0x00
-#define QPHY_V3_DP_COM_SW_RESET				0x04
-#define QPHY_V3_DP_COM_POWER_DOWN_CTRL			0x08
-#define QPHY_V3_DP_COM_SWI_CTRL				0x0c
-#define QPHY_V3_DP_COM_TYPEC_CTRL			0x10
-#define QPHY_V3_DP_COM_TYPEC_PWRDN_CTRL			0x14
-#define QPHY_V3_DP_COM_RESET_OVRD_CTRL			0x1c
-
-/* QSERDES V3 COM bits */
-# define QSERDES_V3_COM_BIAS_EN				0x0001
-# define QSERDES_V3_COM_BIAS_EN_MUX			0x0002
-# define QSERDES_V3_COM_CLKBUF_R_EN			0x0004
-# define QSERDES_V3_COM_CLKBUF_L_EN			0x0008
-# define QSERDES_V3_COM_EN_SYSCLK_TX_SEL		0x0010
-# define QSERDES_V3_COM_CLKBUF_RX_DRIVE_L		0x0020
-# define QSERDES_V3_COM_CLKBUF_RX_DRIVE_R		0x0040
-
-/* QSERDES V3 TX bits */
-# define DP_PHY_TXn_TX_EMP_POST1_LVL_MASK		0x001f
-# define DP_PHY_TXn_TX_EMP_POST1_LVL_MUX_EN		0x0020
-# define DP_PHY_TXn_TX_DRV_LVL_MASK			0x001f
-# define DP_PHY_TXn_TX_DRV_LVL_MUX_EN			0x0020
-
-/* QMP PHY - DP PHY registers */
-#define QSERDES_DP_PHY_REVISION_ID0			0x000
-#define QSERDES_DP_PHY_REVISION_ID1			0x004
-#define QSERDES_DP_PHY_REVISION_ID2			0x008
-#define QSERDES_DP_PHY_REVISION_ID3			0x00c
-#define QSERDES_DP_PHY_CFG				0x010
-#define QSERDES_DP_PHY_PD_CTL				0x018
-# define DP_PHY_PD_CTL_PWRDN				0x001
-# define DP_PHY_PD_CTL_PSR_PWRDN			0x002
-# define DP_PHY_PD_CTL_AUX_PWRDN			0x004
-# define DP_PHY_PD_CTL_LANE_0_1_PWRDN			0x008
-# define DP_PHY_PD_CTL_LANE_2_3_PWRDN			0x010
-# define DP_PHY_PD_CTL_PLL_PWRDN			0x020
-# define DP_PHY_PD_CTL_DP_CLAMP_EN			0x040
-#define QSERDES_DP_PHY_MODE				0x01c
-#define QSERDES_DP_PHY_AUX_CFG0				0x020
-#define QSERDES_DP_PHY_AUX_CFG1				0x024
-#define QSERDES_DP_PHY_AUX_CFG2				0x028
-#define QSERDES_DP_PHY_AUX_CFG3				0x02c
-#define QSERDES_DP_PHY_AUX_CFG4				0x030
-#define QSERDES_DP_PHY_AUX_CFG5				0x034
-#define QSERDES_DP_PHY_AUX_CFG6				0x038
-#define QSERDES_DP_PHY_AUX_CFG7				0x03c
-#define QSERDES_DP_PHY_AUX_CFG8				0x040
-#define QSERDES_DP_PHY_AUX_CFG9				0x044
-
-/* Only for QMP V3 PHY - DP PHY registers */
-#define QSERDES_V3_DP_PHY_AUX_INTERRUPT_MASK		0x048
-# define PHY_AUX_STOP_ERR_MASK				0x01
-# define PHY_AUX_DEC_ERR_MASK				0x02
-# define PHY_AUX_SYNC_ERR_MASK				0x04
-# define PHY_AUX_ALIGN_ERR_MASK				0x08
-# define PHY_AUX_REQ_ERR_MASK				0x10
-
-#define QSERDES_V3_DP_PHY_AUX_INTERRUPT_CLEAR		0x04c
-#define QSERDES_V3_DP_PHY_AUX_BIST_CFG			0x050
-
-#define QSERDES_V3_DP_PHY_VCO_DIV			0x064
-#define QSERDES_V3_DP_PHY_TX0_TX1_LANE_CTL		0x06c
-#define QSERDES_V3_DP_PHY_TX2_TX3_LANE_CTL		0x088
-
-#define QSERDES_V3_DP_PHY_SPARE0			0x0ac
-#define DP_PHY_SPARE0_MASK				0x0f
-#define DP_PHY_SPARE0_ORIENTATION_INFO_SHIFT		0x04(0x0004)
-
-#define QSERDES_V3_DP_PHY_STATUS			0x0c0
-
-/* Only for QMP V4 PHY - DP PHY registers */
-#define QSERDES_V4_DP_PHY_CFG_1				0x014
-#define QSERDES_V4_DP_PHY_AUX_INTERRUPT_MASK		0x054
-#define QSERDES_V4_DP_PHY_AUX_INTERRUPT_CLEAR		0x058
-#define QSERDES_V4_DP_PHY_VCO_DIV			0x070
-#define QSERDES_V4_DP_PHY_TX0_TX1_LANE_CTL		0x078
-#define QSERDES_V4_DP_PHY_TX2_TX3_LANE_CTL		0x09c
-#define QSERDES_V4_DP_PHY_SPARE0			0x0c8
-#define QSERDES_V4_DP_PHY_AUX_INTERRUPT_STATUS		0x0d8
-#define QSERDES_V4_DP_PHY_STATUS			0x0dc
-
-#define QSERDES_V5_DP_PHY_STATUS			0x0dc
-
-/* Only for QMP V6 PHY - DP PHY registers */
-#define QSERDES_V6_DP_PHY_AUX_INTERRUPT_STATUS		0x0e0
-#define QSERDES_V6_DP_PHY_STATUS			0x0e4
+/* QPHY_SW_RESET bit */
+#define SW_RESET				BIT(0)
+/* QPHY_POWER_DOWN_CONTROL */
+#define SW_PWRDN				BIT(0)
+#define REFCLK_DRV_DSBL				BIT(1) /* PCIe */
+
+/* QPHY_START_CONTROL bits */
+#define SERDES_START				BIT(0)
+#define PCS_START				BIT(1)
+
+/* QPHY_PCS_STATUS bit */
+#define PHYSTATUS				BIT(6)
+#define PHYSTATUS_4_20				BIT(7)
+
+/* QPHY_PCS_AUTONOMOUS_MODE_CTRL register bits */
+#define ARCVR_DTCT_EN				BIT(0)
+#define ALFPS_DTCT_EN				BIT(1)
+#define ARCVR_DTCT_EVENT_SEL			BIT(4)
+
+/* QPHY_PCS_LFPS_RXTERM_IRQ_CLEAR register bits */
+#define IRQ_CLEAR				BIT(0)
+
+/* QPHY_PCS_MISC_CLAMP_ENABLE register bits */
+#define CLAMP_EN				BIT(0) /* enables i/o clamp_n */
 
 #endif

drivers/phy/ralink/phy-mt7621-pci.c

@@ -263,7 +263,7 @@ static const struct phy_ops mt7621_pci_phy_ops = {
 };
 
 static struct phy *mt7621_pcie_phy_of_xlate(struct device *dev,
-					    struct of_phandle_args *args)
+					    const struct of_phandle_args *args)
 {
 	struct mt7621_pci_phy *mt7621_phy = dev_get_drvdata(dev);
 

drivers/phy/renesas/phy-rcar-gen2.c

@@ -306,7 +306,7 @@ static const struct of_device_id rcar_gen2_phy_match_table[] = {
 MODULE_DEVICE_TABLE(of, rcar_gen2_phy_match_table);
 
 static struct phy *rcar_gen2_phy_xlate(struct device *dev,
-				       struct of_phandle_args *args)
+				       const struct of_phandle_args *args)
 {
 	struct rcar_gen2_phy_driver *drv;
 	struct device_node *np = args->np;

drivers/phy/renesas/phy-rcar-gen3-usb2.c

@@ -608,7 +608,7 @@ static const unsigned int rcar_gen3_phy_cable[] = {
 };
 
 static struct phy *rcar_gen3_phy_usb2_xlate(struct device *dev,
-					    struct of_phandle_args *args)
+					    const struct of_phandle_args *args)
 {
 	struct rcar_gen3_chan *ch = dev_get_drvdata(dev);
 

drivers/phy/renesas/r8a779f0-ether-serdes.c

@@ -334,7 +334,7 @@ static const struct phy_ops r8a779f0_eth_serdes_ops = {
 };
 
 static struct phy *r8a779f0_eth_serdes_xlate(struct device *dev,
-					     struct of_phandle_args *args)
+					     const struct of_phandle_args *args)
 {
 	struct r8a779f0_eth_serdes_drv_data *dd = dev_get_drvdata(dev);
 

drivers/phy/rockchip/Kconfig

@@ -83,6 +83,14 @@ config PHY_ROCKCHIP_PCIE
 	help
 	  Enable this to support the Rockchip PCIe PHY.
 
+config PHY_ROCKCHIP_SAMSUNG_HDPTX
+	tristate "Rockchip Samsung HDMI/eDP Combo PHY driver"
+	depends on (ARCH_ROCKCHIP || COMPILE_TEST) && OF
+	select GENERIC_PHY
+	help
+	  Enable this to support the Rockchip HDMI/eDP Combo PHY
+	  with Samsung IP block.
+
 config PHY_ROCKCHIP_SNPS_PCIE3
 	tristate "Rockchip Snps PCIe3 PHY Driver"
 	depends on (ARCH_ROCKCHIP && OF) || COMPILE_TEST

drivers/phy/rockchip/Makefile

@@ -8,6 +8,7 @@ obj-$(CONFIG_PHY_ROCKCHIP_INNO_HDMI)	+= phy-rockchip-inno-hdmi.o
 obj-$(CONFIG_PHY_ROCKCHIP_INNO_USB2)	+= phy-rockchip-inno-usb2.o
 obj-$(CONFIG_PHY_ROCKCHIP_NANENG_COMBO_PHY)	+= phy-rockchip-naneng-combphy.o
 obj-$(CONFIG_PHY_ROCKCHIP_PCIE)		+= phy-rockchip-pcie.o
+obj-$(CONFIG_PHY_ROCKCHIP_SAMSUNG_HDPTX)	+= phy-rockchip-samsung-hdptx.o
 obj-$(CONFIG_PHY_ROCKCHIP_SNPS_PCIE3)	+= phy-rockchip-snps-pcie3.o
 obj-$(CONFIG_PHY_ROCKCHIP_TYPEC)	+= phy-rockchip-typec.o
 obj-$(CONFIG_PHY_ROCKCHIP_USB)		+= phy-rockchip-usb.o

drivers/phy/rockchip/phy-rockchip-naneng-combphy.c

@@ -251,7 +251,7 @@ static const struct phy_ops rochchip_combphy_ops = {
 	.owner = THIS_MODULE,
 };
 
-static struct phy *rockchip_combphy_xlate(struct device *dev, struct of_phandle_args *args)
+static struct phy *rockchip_combphy_xlate(struct device *dev, const struct of_phandle_args *args)
 {
 	struct rockchip_combphy_priv *priv = dev_get_drvdata(dev);
 

drivers/phy/rockchip/phy-rockchip-pcie.c

@@ -82,7 +82,7 @@ static struct rockchip_pcie_phy *to_pcie_phy(struct phy_pcie_instance *inst)
 }
 
 static struct phy *rockchip_pcie_phy_of_xlate(struct device *dev,
-					      struct of_phandle_args *args)
+					      const struct of_phandle_args *args)
 {
 	struct rockchip_pcie_phy *rk_phy = dev_get_drvdata(dev);
 

drivers/phy/samsung/phy-exynos-mipi-video.c

@@ -274,7 +274,7 @@ static int exynos_mipi_video_phy_power_off(struct phy *phy)
 }
 
 static struct phy *exynos_mipi_video_phy_xlate(struct device *dev,
-					struct of_phandle_args *args)
+					const struct of_phandle_args *args)
 {
 	struct exynos_mipi_video_phy *state = dev_get_drvdata(dev);
 

drivers/phy/samsung/phy-exynos5-usbdrd.c

@@ -715,7 +715,7 @@ static int exynos5420_usbdrd_phy_calibrate(struct exynos5_usbdrd_phy *phy_drd)
 }
 
 static struct phy *exynos5_usbdrd_phy_xlate(struct device *dev,
-					struct of_phandle_args *args)
+					const struct of_phandle_args *args)
 {
 	struct exynos5_usbdrd_phy *phy_drd = dev_get_drvdata(dev);
 

drivers/phy/samsung/phy-samsung-usb2.c

@@ -87,7 +87,7 @@ static const struct phy_ops samsung_usb2_phy_ops = {
 };
 
 static struct phy *samsung_usb2_phy_xlate(struct device *dev,
-					struct of_phandle_args *args)
+					const struct of_phandle_args *args)
 {
 	struct samsung_usb2_phy_driver *drv;
 

drivers/phy/socionext/phy-uniphier-usb2.c

@@ -81,7 +81,7 @@ static int uniphier_u2phy_init(struct phy *phy)
 }
 
 static struct phy *uniphier_u2phy_xlate(struct device *dev,
-					struct of_phandle_args *args)
+					const struct of_phandle_args *args)
 {
 	struct uniphier_u2phy_priv *priv = dev_get_drvdata(dev);
 

drivers/phy/st/phy-miphy28lp.c

@@ -1074,7 +1074,7 @@ static int miphy28lp_get_addr(struct miphy28lp_phy *miphy_phy)
 }
 
 static struct phy *miphy28lp_xlate(struct device *dev,
-				   struct of_phandle_args *args)
+				   const struct of_phandle_args *args)
 {
 	struct miphy28lp_dev *miphy_dev = dev_get_drvdata(dev);
 	struct miphy28lp_phy *miphy_phy = NULL;

drivers/phy/st/phy-spear1310-miphy.c

@@ -183,7 +183,7 @@ static const struct phy_ops spear1310_miphy_ops = {
 };
 
 static struct phy *spear1310_miphy_xlate(struct device *dev,
-					 struct of_phandle_args *args)
+					 const struct of_phandle_args *args)
 {
 	struct spear1310_miphy_priv *priv = dev_get_drvdata(dev);
 

drivers/phy/st/phy-spear1340-miphy.c

@@ -220,7 +220,7 @@ static SIMPLE_DEV_PM_OPS(spear1340_miphy_pm_ops, spear1340_miphy_suspend,
 			 spear1340_miphy_resume);
 
 static struct phy *spear1340_miphy_xlate(struct device *dev,
-					 struct of_phandle_args *args)
+					 const struct of_phandle_args *args)
 {
 	struct spear1340_miphy_priv *priv = dev_get_drvdata(dev);
 

drivers/phy/st/phy-stm32-usbphyc.c

@@ -574,7 +574,7 @@ static void stm32_usbphyc_switch_setup(struct stm32_usbphyc *usbphyc,
 }
 
 static struct phy *stm32_usbphyc_of_xlate(struct device *dev,
-					  struct of_phandle_args *args)
+					  const struct of_phandle_args *args)
 {
 	struct stm32_usbphyc *usbphyc = dev_get_drvdata(dev);
 	struct stm32_usbphyc_phy *usbphyc_phy = NULL;

drivers/phy/tegra/xusb.c

@@ -22,7 +22,7 @@
 #include "xusb.h"
 
 static struct phy *tegra_xusb_pad_of_xlate(struct device *dev,
-					   struct of_phandle_args *args)
+					   const struct of_phandle_args *args)
 {
 	struct tegra_xusb_pad *pad = dev_get_drvdata(dev);
 	struct phy *phy = NULL;

drivers/phy/ti/phy-am654-serdes.c

@@ -495,7 +495,7 @@ static void serdes_am654_release(struct phy *x)
 }
 
 static struct phy *serdes_am654_xlate(struct device *dev,
-				      struct of_phandle_args *args)
+				      const struct of_phandle_args *args)
 {
 	struct serdes_am654 *am654_phy;
 	struct phy *phy;

drivers/phy/ti/phy-da8xx-usb.c

@@ -119,7 +119,7 @@ static const struct phy_ops da8xx_usb20_phy_ops = {
 };
 
 static struct phy *da8xx_usb_phy_of_xlate(struct device *dev,
-					 struct of_phandle_args *args)
+					 const struct of_phandle_args *args)
 {
 	struct da8xx_usb_phy *d_phy = dev_get_drvdata(dev);
 

drivers/phy/ti/phy-gmii-sel.c

@@ -297,7 +297,7 @@ static const struct phy_ops phy_gmii_sel_ops = {
 };
 
 static struct phy *phy_gmii_sel_of_xlate(struct device *dev,
-					 struct of_phandle_args *args)
+					 const struct of_phandle_args *args)
 {
 	struct phy_gmii_sel_priv *priv = dev_get_drvdata(dev);
 	int phy_id = args->args[0];
@@ -494,11 +494,35 @@ static int phy_gmii_sel_probe(struct platform_device *pdev)
 	return 0;
 }
 
+static int phy_gmii_sel_resume_noirq(struct device *dev)
+{
+	struct phy_gmii_sel_priv *priv = dev_get_drvdata(dev);
+	struct phy_gmii_sel_phy_priv *if_phys = priv->if_phys;
+	int ret, i;
+
+	for (i = 0; i < priv->num_ports; i++) {
+		if (if_phys[i].phy_if_mode) {
+			ret = phy_gmii_sel_mode(if_phys[i].if_phy,
+						PHY_MODE_ETHERNET, if_phys[i].phy_if_mode);
+			if (ret) {
+				dev_err(dev, "port%u: restore mode fail %d\n",
+					if_phys[i].if_phy->id, ret);
+				return ret;
+			}
+		}
+	}
+
+	return 0;
+}
+
+static DEFINE_NOIRQ_DEV_PM_OPS(phy_gmii_sel_pm_ops, NULL, phy_gmii_sel_resume_noirq);
+
 static struct platform_driver phy_gmii_sel_driver = {
 	.probe		= phy_gmii_sel_probe,
 	.driver		= {
 		.name	= "phy-gmii-sel",
 		.of_match_table = phy_gmii_sel_id_table,
+		.pm = pm_sleep_ptr(&phy_gmii_sel_pm_ops),
 	},
 };
 module_platform_driver(phy_gmii_sel_driver);

drivers/phy/xilinx/phy-zynqmp.c

@@ -768,7 +768,7 @@ static const unsigned int icm_matrix[NUM_LANES][CONTROLLERS_PER_LANE] = {
 
 /* Translate OF phandle and args to PHY instance. */
 static struct phy *xpsgtr_xlate(struct device *dev,
-				struct of_phandle_args *args)
+				const struct of_phandle_args *args)
 {
 	struct xpsgtr_dev *gtr_dev = dev_get_drvdata(dev);
 	struct xpsgtr_phy *gtr_phy;

drivers/pinctrl/tegra/pinctrl-tegra-xusb.c

@@ -685,7 +685,7 @@ static const struct phy_ops sata_phy_ops = {
 };
 
 static struct phy *tegra_xusb_padctl_xlate(struct device *dev,
-					   struct of_phandle_args *args)
+					   const struct of_phandle_args *args)
 {
 	struct tegra_xusb_padctl *padctl = dev_get_drvdata(dev);
 	unsigned int index = args->args[0];

include/linux/phy/phy.h

@@ -176,7 +176,7 @@ struct phy_provider {
 	struct module		*owner;
 	struct list_head	list;
 	struct phy * (*of_xlate)(struct device *dev,
-		struct of_phandle_args *args);
+				 const struct of_phandle_args *args);
 };
 
 /**
@@ -265,7 +265,7 @@ void phy_put(struct device *dev, struct phy *phy);
 void devm_phy_put(struct device *dev, struct phy *phy);
 struct phy *of_phy_get(struct device_node *np, const char *con_id);
 struct phy *of_phy_simple_xlate(struct device *dev,
-	struct of_phandle_args *args);
+				const struct of_phandle_args *args);
 struct phy *phy_create(struct device *dev, struct device_node *node,
 		       const struct phy_ops *ops);
 struct phy *devm_phy_create(struct device *dev, struct device_node *node,
@@ -275,11 +275,11 @@ void devm_phy_destroy(struct device *dev, struct phy *phy);
 struct phy_provider *__of_phy_provider_register(struct device *dev,
 	struct device_node *children, struct module *owner,
 	struct phy * (*of_xlate)(struct device *dev,
-				 struct of_phandle_args *args));
+				 const struct of_phandle_args *args));
 struct phy_provider *__devm_of_phy_provider_register(struct device *dev,
 	struct device_node *children, struct module *owner,
 	struct phy * (*of_xlate)(struct device *dev,
-				 struct of_phandle_args *args));
+				 const struct of_phandle_args *args));
 void of_phy_provider_unregister(struct phy_provider *phy_provider);
 void devm_of_phy_provider_unregister(struct device *dev,
 	struct phy_provider *phy_provider);
@@ -479,7 +479,7 @@ static inline struct phy *of_phy_get(struct device_node *np, const char *con_id)
 }
 
 static inline struct phy *of_phy_simple_xlate(struct device *dev,
-	struct of_phandle_args *args)
+					      const struct of_phandle_args *args)
 {
 	return ERR_PTR(-ENOSYS);
 }
@@ -509,7 +509,7 @@ static inline void devm_phy_destroy(struct device *dev, struct phy *phy)
 static inline struct phy_provider *__of_phy_provider_register(
 	struct device *dev, struct device_node *children, struct module *owner,
 	struct phy * (*of_xlate)(struct device *dev,
-				 struct of_phandle_args *args))
+				 const struct of_phandle_args *args))
 {
 	return ERR_PTR(-ENOSYS);
 }
@@ -517,7 +517,7 @@ static inline struct phy_provider *__of_phy_provider_register(
 static inline struct phy_provider *__devm_of_phy_provider_register(struct device
 	*dev, struct device_node *children, struct module *owner,
 	struct phy * (*of_xlate)(struct device *dev,
-				 struct of_phandle_args *args))
+				 const struct of_phandle_args *args))
 {
 	return ERR_PTR(-ENOSYS);
 }