Merge branch 'for-linus' of git://git.o-hand.com/linux-rpurdie-leds

* 'for-linus' of git://git.o-hand.com/linux-rpurdie-leds:
  leds: leds-pwm: Set led_classdev max_brightness
  leds: leds-lp3944.h - remove unneeded includes
  leds: use default-on trigger for Cobalt Qube
  leds: drivers/leds/leds-ss4200.c: fix return statement
  leds: leds-pca9532.h- indent with tabs, not spaces
  leds: Add LED class driver for regulator driven LEDs.
  leds: leds-cobalt-qube.c: use resource_size()
  leds: leds-cobalt-raq.c - use resource_size()
  leds: Add driver for ADP5520/ADP5501 MFD PMICs
  leds: Add driver for LT3593 controlled LEDs
  leds-ss4200: Check pci_enable_device return
  leds: leds-alix2c - take port address from MSR
  leds: LED driver for Intel NAS SS4200 series (v5)

drivers/leds/Kconfig

@@ -229,6 +229,12 @@ config LEDS_PWM
 	help
 	  This option enables support for pwm driven LEDs
 
+config LEDS_REGULATOR
+	tristate "REGULATOR driven LED support"
+	depends on LEDS_CLASS && REGULATOR
+	help
+	  This option enables support for regulator driven LEDs.
+
 config LEDS_BD2802
 	tristate "LED driver for BD2802 RGB LED"
 	depends on LEDS_CLASS && I2C
@@ -236,6 +242,33 @@ config LEDS_BD2802
 	  This option enables support for BD2802GU RGB LED driver chips
 	  accessed via the I2C bus.
 
+config LEDS_INTEL_SS4200
+	tristate "LED driver for Intel NAS SS4200 series"
+	depends on LEDS_CLASS && PCI && DMI
+	help
+	  This option enables support for the Intel SS4200 series of
+	  Network Attached Storage servers.  You may control the hard
+	  drive or power LEDs on the front panel.  Using this driver
+	  can stop the front LED from blinking after startup.
+
+config LEDS_LT3593
+	tristate "LED driver for LT3593 controllers"
+	depends on LEDS_CLASS && GENERIC_GPIO
+	help
+	  This option enables support for LEDs driven by a Linear Technology
+	  LT3593 controller. This controller uses a special one-wire pulse
+	  coding protocol to set the brightness.
+
+config LEDS_ADP5520
+	tristate "LED Support for ADP5520/ADP5501 PMIC"
+	depends on LEDS_CLASS && PMIC_ADP5520
+	help
+	  This option enables support for on-chip LED drivers found
+	  on Analog Devices ADP5520/ADP5501 PMICs.
+
+	  To compile this driver as a module, choose M here: the module will
+	  be called leds-adp5520.
+
 comment "LED Triggers"
 
 config LEDS_TRIGGERS

drivers/leds/Makefile

@@ -29,6 +29,10 @@ obj-$(CONFIG_LEDS_DA903X)		+= leds-da903x.o
 obj-$(CONFIG_LEDS_WM831X_STATUS)	+= leds-wm831x-status.o
 obj-$(CONFIG_LEDS_WM8350)		+= leds-wm8350.o
 obj-$(CONFIG_LEDS_PWM)			+= leds-pwm.o
+obj-$(CONFIG_LEDS_REGULATOR)		+= leds-regulator.o
+obj-$(CONFIG_LEDS_INTEL_SS4200)		+= leds-ss4200.o
+obj-$(CONFIG_LEDS_LT3593)		+= leds-lt3593.o
+obj-$(CONFIG_LEDS_ADP5520)		+= leds-adp5520.o
 
 # LED SPI Drivers
 obj-$(CONFIG_LEDS_DAC124S085)		+= leds-dac124s085.o

drivers/leds/leds-adp5520.c

+/*
+ * LEDs driver for Analog Devices ADP5520/ADP5501 MFD PMICs
+ *
+ * Copyright 2009 Analog Devices Inc.
+ *
+ * Loosely derived from leds-da903x:
+ * Copyright (C) 2008 Compulab, Ltd.
+ * 	Mike Rapoport <mike@compulab.co.il>
+ *
+ * Copyright (C) 2006-2008 Marvell International Ltd.
+ * 	Eric Miao <eric.miao@marvell.com>
+ *
+ * Licensed under the GPL-2 or later.
+ */
+
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/leds.h>
+#include <linux/workqueue.h>
+#include <linux/mfd/adp5520.h>
+
+struct adp5520_led {
+	struct led_classdev	cdev;
+	struct work_struct	work;
+	struct device		*master;
+	enum led_brightness	new_brightness;
+	int			id;
+	int			flags;
+};
+
+static void adp5520_led_work(struct work_struct *work)
+{
+	struct adp5520_led *led = container_of(work, struct adp5520_led, work);
+	adp5520_write(led->master, ADP5520_LED1_CURRENT + led->id - 1,
+			 led->new_brightness >> 2);
+}
+
+static void adp5520_led_set(struct led_classdev *led_cdev,
+			   enum led_brightness value)
+{
+	struct adp5520_led *led;
+
+	led = container_of(led_cdev, struct adp5520_led, cdev);
+	led->new_brightness = value;
+	schedule_work(&led->work);
+}
+
+static int adp5520_led_setup(struct adp5520_led *led)
+{
+	struct device *dev = led->master;
+	int flags = led->flags;
+	int ret = 0;
+
+	switch (led->id) {
+	case FLAG_ID_ADP5520_LED1_ADP5501_LED0:
+		ret |= adp5520_set_bits(dev, ADP5520_LED_TIME,
+					(flags >> ADP5520_FLAG_OFFT_SHIFT) &
+					ADP5520_FLAG_OFFT_MASK);
+		ret |= adp5520_set_bits(dev, ADP5520_LED_CONTROL,
+					ADP5520_LED1_EN);
+		break;
+	case FLAG_ID_ADP5520_LED2_ADP5501_LED1:
+		ret |= adp5520_set_bits(dev,  ADP5520_LED_TIME,
+					((flags >> ADP5520_FLAG_OFFT_SHIFT) &
+					ADP5520_FLAG_OFFT_MASK) << 2);
+		ret |= adp5520_clr_bits(dev, ADP5520_LED_CONTROL,
+					 ADP5520_R3_MODE);
+		ret |= adp5520_set_bits(dev, ADP5520_LED_CONTROL,
+					ADP5520_LED2_EN);
+		break;
+	case FLAG_ID_ADP5520_LED3_ADP5501_LED2:
+		ret |= adp5520_set_bits(dev,  ADP5520_LED_TIME,
+					((flags >> ADP5520_FLAG_OFFT_SHIFT) &
+					ADP5520_FLAG_OFFT_MASK) << 4);
+		ret |= adp5520_clr_bits(dev, ADP5520_LED_CONTROL,
+					ADP5520_C3_MODE);
+		ret |= adp5520_set_bits(dev, ADP5520_LED_CONTROL,
+					ADP5520_LED3_EN);
+		break;
+	}
+
+	return ret;
+}
+
+static int __devinit adp5520_led_prepare(struct platform_device *pdev)
+{
+	struct adp5520_leds_platform_data *pdata = pdev->dev.platform_data;
+	struct device *dev = pdev->dev.parent;
+	int ret = 0;
+
+	ret |= adp5520_write(dev, ADP5520_LED1_CURRENT, 0);
+	ret |= adp5520_write(dev, ADP5520_LED2_CURRENT, 0);
+	ret |= adp5520_write(dev, ADP5520_LED3_CURRENT, 0);
+	ret |= adp5520_write(dev, ADP5520_LED_TIME, pdata->led_on_time << 6);
+	ret |= adp5520_write(dev, ADP5520_LED_FADE, FADE_VAL(pdata->fade_in,
+		 pdata->fade_out));
+
+	return ret;
+}
+
+static int __devinit adp5520_led_probe(struct platform_device *pdev)
+{
+	struct adp5520_leds_platform_data *pdata = pdev->dev.platform_data;
+	struct adp5520_led *led, *led_dat;
+	struct led_info *cur_led;
+	int ret, i;
+
+	if (pdata == NULL) {
+		dev_err(&pdev->dev, "missing platform data\n");
+		return -ENODEV;
+	}
+
+	if (pdata->num_leds > ADP5520_01_MAXLEDS) {
+		dev_err(&pdev->dev, "can't handle more than %d LEDS\n",
+				 ADP5520_01_MAXLEDS);
+		return -EFAULT;
+	}
+
+	led = kzalloc(sizeof(*led) * pdata->num_leds, GFP_KERNEL);
+	if (led == NULL) {
+		dev_err(&pdev->dev, "failed to alloc memory\n");
+		return -ENOMEM;
+	}
+
+	ret = adp5520_led_prepare(pdev);
+
+	if (ret) {
+		dev_err(&pdev->dev, "failed to write\n");
+		goto err_free;
+	}
+
+	for (i = 0; i < pdata->num_leds; ++i) {
+		cur_led = &pdata->leds[i];
+		led_dat = &led[i];
+
+		led_dat->cdev.name = cur_led->name;
+		led_dat->cdev.default_trigger = cur_led->default_trigger;
+		led_dat->cdev.brightness_set = adp5520_led_set;
+		led_dat->cdev.brightness = LED_OFF;
+
+		if (cur_led->flags & ADP5520_FLAG_LED_MASK)
+			led_dat->flags = cur_led->flags;
+		else
+			led_dat->flags = i + 1;
+
+		led_dat->id = led_dat->flags & ADP5520_FLAG_LED_MASK;
+
+		led_dat->master = pdev->dev.parent;
+		led_dat->new_brightness = LED_OFF;
+
+		INIT_WORK(&led_dat->work, adp5520_led_work);
+
+		ret = led_classdev_register(led_dat->master, &led_dat->cdev);
+		if (ret) {
+			dev_err(&pdev->dev, "failed to register LED %d\n",
+				led_dat->id);
+			goto err;
+		}
+
+		ret = adp5520_led_setup(led_dat);
+		if (ret) {
+			dev_err(&pdev->dev, "failed to write\n");
+			i++;
+			goto err;
+		}
+	}
+
+	platform_set_drvdata(pdev, led);
+	return 0;
+
+err:
+	if (i > 0) {
+		for (i = i - 1; i >= 0; i--) {
+			led_classdev_unregister(&led[i].cdev);
+			cancel_work_sync(&led[i].work);
+		}
+	}
+
+err_free:
+	kfree(led);
+	return ret;
+}
+
+static int __devexit adp5520_led_remove(struct platform_device *pdev)
+{
+	struct adp5520_leds_platform_data *pdata = pdev->dev.platform_data;
+	struct adp5520_led *led;
+	int i;
+
+	led = platform_get_drvdata(pdev);
+
+	adp5520_clr_bits(led->master, ADP5520_LED_CONTROL,
+		 ADP5520_LED1_EN | ADP5520_LED2_EN | ADP5520_LED3_EN);
+
+	for (i = 0; i < pdata->num_leds; i++) {
+		led_classdev_unregister(&led[i].cdev);
+		cancel_work_sync(&led[i].work);
+	}
+
+	kfree(led);
+	return 0;
+}
+
+static struct platform_driver adp5520_led_driver = {
+	.driver	= {
+		.name	= "adp5520-led",
+		.owner	= THIS_MODULE,
+	},
+	.probe		= adp5520_led_probe,
+	.remove		= __devexit_p(adp5520_led_remove),
+};
+
+static int __init adp5520_led_init(void)
+{
+	return platform_driver_register(&adp5520_led_driver);
+}
+module_init(adp5520_led_init);
+
+static void __exit adp5520_led_exit(void)
+{
+	platform_driver_unregister(&adp5520_led_driver);
+}
+module_exit(adp5520_led_exit);
+
+MODULE_AUTHOR("Michael Hennerich <hennerich@blackfin.uclinux.org>");
+MODULE_DESCRIPTION("LEDS ADP5520(01) Driver");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:adp5520-led");

drivers/leds/leds-alix2.c

@@ -11,11 +11,24 @@
 #include <linux/module.h>
 #include <linux/platform_device.h>
 #include <linux/string.h>
+#include <linux/pci.h>
 
 static int force = 0;
 module_param(force, bool, 0444);
 MODULE_PARM_DESC(force, "Assume system has ALIX.2/ALIX.3 style LEDs");
 
+#define MSR_LBAR_GPIO		0x5140000C
+#define CS5535_GPIO_SIZE	256
+
+static u32 gpio_base;
+
+static struct pci_device_id divil_pci[] = {
+	{ PCI_DEVICE(PCI_VENDOR_ID_NS,  PCI_DEVICE_ID_NS_CS5535_ISA) },
+	{ PCI_DEVICE(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_CS5536_ISA) },
+	{ } /* NULL entry */
+};
+MODULE_DEVICE_TABLE(pci, divil_pci);
+
 struct alix_led {
 	struct led_classdev cdev;
 	unsigned short port;
@@ -30,9 +43,9 @@ static void alix_led_set(struct led_classdev *led_cdev,
 		container_of(led_cdev, struct alix_led, cdev);
 
 	if (brightness)
-		outl(led_dev->on_value, led_dev->port);
+		outl(led_dev->on_value, gpio_base + led_dev->port);
 	else
-		outl(led_dev->off_value, led_dev->port);
+		outl(led_dev->off_value, gpio_base + led_dev->port);
 }
 
 static struct alix_led alix_leds[] = {
@@ -41,7 +54,7 @@ static struct alix_led alix_leds[] = {
 			.name = "alix:1",
 			.brightness_set = alix_led_set,
 		},
-		.port = 0x6100,
+		.port = 0x00,
 		.on_value = 1 << 22,
 		.off_value = 1 << 6,
 	},
@@ -50,7 +63,7 @@ static struct alix_led alix_leds[] = {
 			.name = "alix:2",
 			.brightness_set = alix_led_set,
 		},
-		.port = 0x6180,
+		.port = 0x80,
 		.on_value = 1 << 25,
 		.off_value = 1 << 9,
 	},
@@ -59,7 +72,7 @@ static struct alix_led alix_leds[] = {
 			.name = "alix:3",
 			.brightness_set = alix_led_set,
 		},
-		.port = 0x6180,
+		.port = 0x80,
 		.on_value = 1 << 27,
 		.off_value = 1 << 11,
 	},
@@ -101,64 +114,104 @@ static struct platform_driver alix_led_driver = {
 	},
 };
 
-static int __init alix_present(void)
+static int __init alix_present(unsigned long bios_phys,
+				const char *alix_sig,
+				size_t alix_sig_len)
 {
-	const unsigned long bios_phys = 0x000f0000;
 	const size_t bios_len = 0x00010000;
-	const char alix_sig[] = "PC Engines ALIX.";
-	const size_t alix_sig_len = sizeof(alix_sig) - 1;
-
 	const char *bios_virt;
 	const char *scan_end;
 	const char *p;
-	int ret = 0;
+	char name[64];
 
 	if (force) {
 		printk(KERN_NOTICE "%s: forced to skip BIOS test, "
 		       "assume system has ALIX.2 style LEDs\n",
 		       KBUILD_MODNAME);
-		ret = 1;
-		goto out;
+		return 1;
 	}
 
 	bios_virt = phys_to_virt(bios_phys);
 	scan_end = bios_virt + bios_len - (alix_sig_len + 2);
 	for (p = bios_virt; p < scan_end; p++) {
 		const char *tail;
+		char *a;
 
-		if (memcmp(p, alix_sig, alix_sig_len) != 0) {
+		if (memcmp(p, alix_sig, alix_sig_len) != 0)
 			continue;
-		}
+
+		memcpy(name, p, sizeof(name));
+
+		/* remove the first \0 character from string */
+		a = strchr(name, '\0');
+		if (a)
+			*a = ' ';
+
+		/* cut the string at a newline */
+		a = strchr(name, '\r');
+		if (a)
+			*a = '\0';
 
 		tail = p + alix_sig_len;
-		if ((tail[0] == '2' || tail[0] == '3') && tail[1] == '\0') {
+		if ((tail[0] == '2' || tail[0] == '3')) {
 			printk(KERN_INFO
 			       "%s: system is recognized as \"%s\"\n",
-			       KBUILD_MODNAME, p);
-			ret = 1;
-			break;
+			       KBUILD_MODNAME, name);
+			return 1;
 		}
 	}
 
-out:
-	return ret;
+	return 0;
 }
 
 static struct platform_device *pdev;
 
-static int __init alix_led_init(void)
+static int __init alix_pci_led_init(void)
 {
-	int ret;
+	u32 low, hi;
 
-	if (!alix_present()) {
-		ret = -ENODEV;
-		goto out;
+	if (pci_dev_present(divil_pci) == 0) {
+		printk(KERN_WARNING KBUILD_MODNAME": DIVIL not found\n");
+		return -ENODEV;
 	}
 
-	/* enable output on GPIO for LED 1,2,3 */
-	outl(1 << 6, 0x6104);
-	outl(1 << 9, 0x6184);
-	outl(1 << 11, 0x6184);
+	/* Grab the GPIO I/O range */
+	rdmsr(MSR_LBAR_GPIO, low, hi);
+
+	/* Check the mask and whether GPIO is enabled (sanity check) */
+	if (hi != 0x0000f001) {
+		printk(KERN_WARNING KBUILD_MODNAME": GPIO not enabled\n");
+		return -ENODEV;
+	}
+
+	/* Mask off the IO base address */
+	gpio_base = low & 0x0000ff00;
+
+	if (!request_region(gpio_base, CS5535_GPIO_SIZE, KBUILD_MODNAME)) {
+		printk(KERN_ERR KBUILD_MODNAME": can't allocate I/O for GPIO\n");
+		return -ENODEV;
+	}
+
+	/* Set GPIO function to output */
+	outl(1 << 6, gpio_base + 0x04);
+	outl(1 << 9, gpio_base + 0x84);
+	outl(1 << 11, gpio_base + 0x84);
+
+	return 0;
+}
+
+static int __init alix_led_init(void)
+{
+	int ret = -ENODEV;
+	const char tinybios_sig[] = "PC Engines ALIX.";
+	const char coreboot_sig[] = "PC Engines\0ALIX.";
+
+	if (alix_present(0xf0000, tinybios_sig, sizeof(tinybios_sig) - 1) ||
+	    alix_present(0x500, coreboot_sig, sizeof(coreboot_sig) - 1))
+		ret = alix_pci_led_init();
+
+	if (ret < 0)
+		return ret;
 
 	pdev = platform_device_register_simple(KBUILD_MODNAME, -1, NULL, 0);
 	if (!IS_ERR(pdev)) {
@@ -168,7 +221,6 @@ static int __init alix_led_init(void)
 	} else
 		ret = PTR_ERR(pdev);
 
-out:
 	return ret;
 }
 
@@ -176,6 +228,7 @@ static void __exit alix_led_exit(void)
 {
 	platform_device_unregister(pdev);
 	platform_driver_unregister(&alix_led_driver);
+	release_region(gpio_base, CS5535_GPIO_SIZE);
 }
 
 module_init(alix_led_init);

drivers/leds/leds-cobalt-qube.c

@@ -31,7 +31,7 @@ static struct led_classdev qube_front_led = {
 	.name			= "qube::front",
 	.brightness		= LED_FULL,
 	.brightness_set		= qube_front_led_set,
-	.default_trigger	= "ide-disk",
+	.default_trigger	= "default-on",
 };
 
 static int __devinit cobalt_qube_led_probe(struct platform_device *pdev)
@@ -43,7 +43,7 @@ static int __devinit cobalt_qube_led_probe(struct platform_device *pdev)
 	if (!res)
 		return -EBUSY;
 
-	led_port = ioremap(res->start, res->end - res->start + 1);
+	led_port = ioremap(res->start, resource_size(res));
 	if (!led_port)
 		return -ENOMEM;
 

drivers/leds/leds-cobalt-raq.c

@@ -84,7 +84,7 @@ static int __devinit cobalt_raq_led_probe(struct platform_device *pdev)
 	if (!res)
 		return -EBUSY;
 
-	led_port = ioremap(res->start, res->end - res->start + 1);
+	led_port = ioremap(res->start, resource_size(res));
 	if (!led_port)
 		return -ENOMEM;
 

drivers/leds/leds-lt3593.c

+/*
+ * LEDs driver for LT3593 controllers
+ *
+ * See the datasheet at http://cds.linear.com/docs/Datasheet/3593f.pdf
+ *
+ * Copyright (c) 2009 Daniel Mack <daniel@caiaq.de>
+ *
+ * Based on leds-gpio.c,
+ *
+ *   Copyright (C) 2007 8D Technologies inc.
+ *   Raphael Assenat <raph@8d.com>
+ *   Copyright (C) 2008 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/leds.h>
+#include <linux/workqueue.h>
+#include <linux/delay.h>
+#include <linux/gpio.h>
+
+struct lt3593_led_data {
+	struct led_classdev cdev;
+	unsigned gpio;
+	struct work_struct work;
+	u8 new_level;
+};
+
+static void lt3593_led_work(struct work_struct *work)
+{
+	int pulses;
+	struct lt3593_led_data *led_dat =
+		container_of(work, struct lt3593_led_data, work);
+
+	/*
+	 * The LT3593 resets its internal current level register to the maximum
+	 * level on the first falling edge on the control pin. Each following
+	 * falling edge decreases the current level by 625uA. Up to 32 pulses
+	 * can be sent, so the maximum power reduction is 20mA.
+	 * After a timeout of 128us, the value is taken from the register and
+	 * applied is to the output driver.
+	 */
+
+	if (led_dat->new_level == 0) {
+		gpio_set_value_cansleep(led_dat->gpio, 0);
+		return;
+	}
+
+	pulses = 32 - (led_dat->new_level * 32) / 255;
+
+	if (pulses == 0) {
+		gpio_set_value_cansleep(led_dat->gpio, 0);
+		mdelay(1);
+		gpio_set_value_cansleep(led_dat->gpio, 1);
+		return;
+	}
+
+	gpio_set_value_cansleep(led_dat->gpio, 1);
+
+	while (pulses--) {
+		gpio_set_value_cansleep(led_dat->gpio, 0);
+		udelay(1);
+		gpio_set_value_cansleep(led_dat->gpio, 1);
+		udelay(1);
+	}
+}
+
+static void lt3593_led_set(struct led_classdev *led_cdev,
+	enum led_brightness value)
+{
+	struct lt3593_led_data *led_dat =
+		container_of(led_cdev, struct lt3593_led_data, cdev);
+
+	led_dat->new_level = value;
+	schedule_work(&led_dat->work);
+}
+
+static int __devinit create_lt3593_led(const struct gpio_led *template,
+	struct lt3593_led_data *led_dat, struct device *parent)
+{
+	int ret, state;
+
+	/* skip leds on GPIOs that aren't available */
+	if (!gpio_is_valid(template->gpio)) {
+		printk(KERN_INFO "%s: skipping unavailable LT3593 LED at gpio %d (%s)\n",
+				KBUILD_MODNAME, template->gpio, template->name);
+		return 0;
+	}
+
+	ret = gpio_request(template->gpio, template->name);
+	if (ret < 0)
+		return ret;
+
+	led_dat->cdev.name = template->name;
+	led_dat->cdev.default_trigger = template->default_trigger;
+	led_dat->gpio = template->gpio;
+
+	led_dat->cdev.brightness_set = lt3593_led_set;
+
+	state = (template->default_state == LEDS_GPIO_DEFSTATE_ON);
+	led_dat->cdev.brightness = state ? LED_FULL : LED_OFF;
+
+	if (!template->retain_state_suspended)
+		led_dat->cdev.flags |= LED_CORE_SUSPENDRESUME;
+
+	ret = gpio_direction_output(led_dat->gpio, state);
+	if (ret < 0)
+		goto err;
+
+	INIT_WORK(&led_dat->work, lt3593_led_work);
+
+	ret = led_classdev_register(parent, &led_dat->cdev);
+	if (ret < 0)
+		goto err;
+
+	printk(KERN_INFO "%s: registered LT3593 LED '%s' at GPIO %d\n",
+		KBUILD_MODNAME, template->name, template->gpio);
+
+	return 0;
+
+err:
+	gpio_free(led_dat->gpio);
+	return ret;
+}
+
+static void delete_lt3593_led(struct lt3593_led_data *led)
+{
+	if (!gpio_is_valid(led->gpio))
+		return;
+
+	led_classdev_unregister(&led->cdev);
+	cancel_work_sync(&led->work);
+	gpio_free(led->gpio);
+}
+
+static int __devinit lt3593_led_probe(struct platform_device *pdev)
+{
+	struct gpio_led_platform_data *pdata = pdev->dev.platform_data;
+	struct lt3593_led_data *leds_data;
+	int i, ret = 0;
+
+	if (!pdata)
+		return -EBUSY;
+
+	leds_data = kzalloc(sizeof(struct lt3593_led_data) * pdata->num_leds,
+				GFP_KERNEL);
+	if (!leds_data)
+		return -ENOMEM;
+
+	for (i = 0; i < pdata->num_leds; i++) {
+		ret = create_lt3593_led(&pdata->leds[i], &leds_data[i],
+				      &pdev->dev);
+		if (ret < 0)
+			goto err;
+	}
+
+	platform_set_drvdata(pdev, leds_data);
+
+	return 0;
+
+err:
+	for (i = i - 1; i >= 0; i--)
+		delete_lt3593_led(&leds_data[i]);
+
+	kfree(leds_data);
+
+	return ret;
+}
+
+static int __devexit lt3593_led_remove(struct platform_device *pdev)
+{
+	int i;
+	struct gpio_led_platform_data *pdata = pdev->dev.platform_data;
+	struct lt3593_led_data *leds_data;
+
+	leds_data = platform_get_drvdata(pdev);
+
+	for (i = 0; i < pdata->num_leds; i++)
+		delete_lt3593_led(&leds_data[i]);
+
+	kfree(leds_data);
+
+	return 0;
+}
+
+static struct platform_driver lt3593_led_driver = {
+	.probe		= lt3593_led_probe,
+	.remove		= __devexit_p(lt3593_led_remove),
+	.driver		= {
+		.name	= "leds-lt3593",
+		.owner	= THIS_MODULE,
+	},
+};
+
+MODULE_ALIAS("platform:leds-lt3593");
+
+static int __init lt3593_led_init(void)
+{
+	return platform_driver_register(&lt3593_led_driver);
+}
+
+static void __exit lt3593_led_exit(void)
+{
+	platform_driver_unregister(&lt3593_led_driver);
+}
+
+module_init(lt3593_led_init);
+module_exit(lt3593_led_exit);
+
+MODULE_AUTHOR("Daniel Mack <daniel@caiaq.de>");
+MODULE_DESCRIPTION("LED driver for LT3593 controllers");
+MODULE_LICENSE("GPL");

drivers/leds/leds-pwm.c

@@ -27,7 +27,6 @@ struct led_pwm_data {
 	struct pwm_device	*pwm;
 	unsigned int 		active_low;
 	unsigned int		period;
-	unsigned int		max_brightness;
 };
 
 static void led_pwm_set(struct led_classdev *led_cdev,
@@ -35,7 +34,7 @@ static void led_pwm_set(struct led_classdev *led_cdev,
 {
 	struct led_pwm_data *led_dat =
 		container_of(led_cdev, struct led_pwm_data, cdev);
-	unsigned int max = led_dat->max_brightness;
+	unsigned int max = led_dat->cdev.max_brightness;
 	unsigned int period =  led_dat->period;
 
 	if (brightness == 0) {
@@ -77,10 +76,10 @@ static int led_pwm_probe(struct platform_device *pdev)
 		led_dat->cdev.name = cur_led->name;
 		led_dat->cdev.default_trigger = cur_led->default_trigger;
 		led_dat->active_low = cur_led->active_low;
-		led_dat->max_brightness = cur_led->max_brightness;
 		led_dat->period = cur_led->pwm_period_ns;
 		led_dat->cdev.brightness_set = led_pwm_set;
 		led_dat->cdev.brightness = LED_OFF;
+		led_dat->cdev.max_brightness = cur_led->max_brightness;
 		led_dat->cdev.flags |= LED_CORE_SUSPENDRESUME;
 
 		ret = led_classdev_register(&pdev->dev, &led_dat->cdev);

drivers/leds/leds-regulator.c

+/*
+ * leds-regulator.c - LED class driver for regulator driven LEDs.
+ *
+ * Copyright (C) 2009 Antonio Ospite <ospite@studenti.unina.it>
+ *
+ * Inspired by leds-wm8350 driver.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#include <linux/module.h>
+#include <linux/err.h>
+#include <linux/workqueue.h>
+#include <linux/leds.h>
+#include <linux/leds-regulator.h>
+#include <linux/platform_device.h>
+#include <linux/regulator/consumer.h>
+
+#define to_regulator_led(led_cdev) \
+	container_of(led_cdev, struct regulator_led, cdev)
+
+struct regulator_led {
+	struct led_classdev cdev;
+	enum led_brightness value;
+	int enabled;
+	struct mutex mutex;
+	struct work_struct work;
+
+	struct regulator *vcc;
+};
+
+static inline int led_regulator_get_max_brightness(struct regulator *supply)
+{
+	int ret;
+	int voltage = regulator_list_voltage(supply, 0);
+
+	if (voltage <= 0)
+		return 1;
+
+	/* even if regulator can't change voltages,
+	 * we still assume it can change status
+	 * and the LED can be turned on and off.
+	 */
+	ret = regulator_set_voltage(supply, voltage, voltage);
+	if (ret < 0)
+		return 1;
+
+	return regulator_count_voltages(supply);
+}
+
+static int led_regulator_get_voltage(struct regulator *supply,
+		enum led_brightness brightness)
+{
+	if (brightness == 0)
+		return -EINVAL;
+
+	return regulator_list_voltage(supply, brightness - 1);
+}
+
+
+static void regulator_led_enable(struct regulator_led *led)
+{
+	int ret;
+
+	if (led->enabled)
+		return;
+
+	ret = regulator_enable(led->vcc);
+	if (ret != 0) {
+		dev_err(led->cdev.dev, "Failed to enable vcc: %d\n", ret);
+		return;
+	}
+
+	led->enabled = 1;
+}
+
+static void regulator_led_disable(struct regulator_led *led)
+{
+	int ret;
+
+	if (!led->enabled)
+		return;
+
+	ret = regulator_disable(led->vcc);
+	if (ret != 0) {
+		dev_err(led->cdev.dev, "Failed to disable vcc: %d\n", ret);
+		return;
+	}
+
+	led->enabled = 0;
+}
+
+static void regulator_led_set_value(struct regulator_led *led)
+{
+	int voltage;
+	int ret;
+
+	mutex_lock(&led->mutex);
+
+	if (led->value == LED_OFF) {
+		regulator_led_disable(led);
+		goto out;
+	}
+
+	if (led->cdev.max_brightness > 1) {
+		voltage = led_regulator_get_voltage(led->vcc, led->value);
+		dev_dbg(led->cdev.dev, "brightness: %d voltage: %d\n",
+				led->value, voltage);
+
+		ret = regulator_set_voltage(led->vcc, voltage, voltage);
+		if (ret != 0)
+			dev_err(led->cdev.dev, "Failed to set voltage %d: %d\n",
+				voltage, ret);
+	}
+
+	regulator_led_enable(led);
+
+out:
+	mutex_unlock(&led->mutex);
+}
+
+static void led_work(struct work_struct *work)
+{
+	struct regulator_led *led;
+
+	led = container_of(work, struct regulator_led, work);
+	regulator_led_set_value(led);
+}
+
+static void regulator_led_brightness_set(struct led_classdev *led_cdev,
+			   enum led_brightness value)
+{
+	struct regulator_led *led = to_regulator_led(led_cdev);
+
+	led->value = value;
+	schedule_work(&led->work);
+}
+
+static int __devinit regulator_led_probe(struct platform_device *pdev)
+{
+	struct led_regulator_platform_data *pdata = pdev->dev.platform_data;
+	struct regulator_led *led;
+	struct regulator *vcc;
+	int ret = 0;
+
+	if (pdata == NULL) {
+		dev_err(&pdev->dev, "no platform data\n");
+		return -ENODEV;
+	}
+
+	vcc = regulator_get_exclusive(&pdev->dev, "vled");
+	if (IS_ERR(vcc)) {
+		dev_err(&pdev->dev, "Cannot get vcc for %s\n", pdata->name);
+		return PTR_ERR(vcc);
+	}
+
+	led = kzalloc(sizeof(*led), GFP_KERNEL);
+	if (led == NULL) {
+		ret = -ENOMEM;
+		goto err_vcc;
+	}
+
+	led->cdev.max_brightness = led_regulator_get_max_brightness(vcc);
+	if (pdata->brightness > led->cdev.max_brightness) {
+		dev_err(&pdev->dev, "Invalid default brightness %d\n",
+				pdata->brightness);
+		ret = -EINVAL;
+		goto err_led;
+	}
+	led->value = pdata->brightness;
+
+	led->cdev.brightness_set = regulator_led_brightness_set;
+	led->cdev.name = pdata->name;
+	led->cdev.flags |= LED_CORE_SUSPENDRESUME;
+	led->vcc = vcc;
+
+	mutex_init(&led->mutex);
+	INIT_WORK(&led->work, led_work);
+
+	platform_set_drvdata(pdev, led);
+
+	ret = led_classdev_register(&pdev->dev, &led->cdev);
+	if (ret < 0) {
+		cancel_work_sync(&led->work);
+		goto err_led;
+	}
+
+	/* to expose the default value to userspace */
+	led->cdev.brightness = led->value;
+
+	/* Set the default led status */
+	regulator_led_set_value(led);
+
+	return 0;
+
+err_led:
+	kfree(led);
+err_vcc:
+	regulator_put(vcc);
+	return ret;
+}
+
+static int __devexit regulator_led_remove(struct platform_device *pdev)
+{
+	struct regulator_led *led = platform_get_drvdata(pdev);
+
+	led_classdev_unregister(&led->cdev);
+	cancel_work_sync(&led->work);
+	regulator_led_disable(led);
+	regulator_put(led->vcc);
+	kfree(led);
+	return 0;
+}
+
+static struct platform_driver regulator_led_driver = {
+	.driver = {
+		   .name  = "leds-regulator",
+		   .owner = THIS_MODULE,
+		   },
+	.probe  = regulator_led_probe,
+	.remove = __devexit_p(regulator_led_remove),
+};
+
+static int __init regulator_led_init(void)
+{
+	return platform_driver_register(&regulator_led_driver);
+}
+module_init(regulator_led_init);
+
+static void __exit regulator_led_exit(void)
+{
+	platform_driver_unregister(&regulator_led_driver);
+}
+module_exit(regulator_led_exit);
+
+MODULE_AUTHOR("Antonio Ospite <ospite@studenti.unina.it>");
+MODULE_DESCRIPTION("Regulator driven LED driver");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:leds-regulator");

include/linux/leds-lp3944.h

@@ -12,9 +12,6 @@
 #ifndef __LINUX_LEDS_LP3944_H
 #define __LINUX_LEDS_LP3944_H
 
-#include <linux/leds.h>
-#include <linux/workqueue.h>
-
 #define LP3944_LED0 0
 #define LP3944_LED1 1
 #define LP3944_LED2 2

include/linux/leds-pca9532.h

@@ -32,7 +32,7 @@ struct pca9532_led {
 	struct i2c_client *client;
 	char *name;
 	struct led_classdev ldev;
-       struct work_struct work;
+	struct work_struct work;
 	enum pca9532_type type;
 	enum pca9532_state state;
 };

include/linux/leds-regulator.h

+/*
+ * leds-regulator.h - platform data structure for regulator driven LEDs.
+ *
+ * Copyright (C) 2009 Antonio Ospite <ospite@studenti.unina.it>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#ifndef __LINUX_LEDS_REGULATOR_H
+#define __LINUX_LEDS_REGULATOR_H
+
+/*
+ * Use "vled" as supply id when declaring the regulator consumer:
+ *
+ * static struct regulator_consumer_supply pcap_regulator_VVIB_consumers [] = {
+ * 	{ .dev_name = "leds-regulator.0", supply = "vled" },
+ * };
+ *
+ * If you have several regulator driven LEDs, you can append a numerical id to
+ * .dev_name as done above, and use the same id when declaring the platform
+ * device:
+ *
+ * static struct led_regulator_platform_data a780_vibrator_data = {
+ * 	.name   = "a780::vibrator",
+ * };
+ *
+ * static struct platform_device a780_vibrator = {
+ * 	.name = "leds-regulator",
+ * 	.id   = 0,
+ * 	.dev  = {
+ * 		.platform_data = &a780_vibrator_data,
+ * 	},
+ * };
+ */
+
+#include <linux/leds.h>
+
+struct led_regulator_platform_data {
+	char *name;                     /* LED name as expected by LED class */
+	enum led_brightness brightness; /* initial brightness value */
+};
+
+#endif /* __LINUX_LEDS_REGULATOR_H */