Commit 9551583e authored by Steve French's avatar Steve French

Merge with /pub/scm/linux/kernel/git/torvalds/linux-2.6.git

parents a2653eba 985834a1
......@@ -7,12 +7,10 @@ Supported adapters:
* VIA Technologies, Inc. VT82C686A/B
Datasheet: Sometimes available at the VIA website
* VIA Technologies, Inc. VT8231, VT8233, VT8233A, VT8235, VT8237
Datasheet: available on request from Via
* VIA Technologies, Inc. VT8231, VT8233, VT8233A, VT8235, VT8237R
Datasheet: available on request from VIA
Authors:
Frodo Looijaard <frodol@dds.nl>,
Philip Edelbrock <phil@netroedge.com>,
Kysti Mlkki <kmalkki@cc.hut.fi>,
Mark D. Studebaker <mdsxyz123@yahoo.com>,
Jean Delvare <khali@linux-fr.org>
......
......@@ -412,7 +412,7 @@ For now, you can ignore the `flags' parameter. It is there for future use.
release_region(address,FOO_EXTENT);
/* SENSORS ONLY END */
ERROR1:
kfree(new_client);
kfree(data);
ERROR0:
return err;
}
......@@ -443,7 +443,7 @@ much simpler than the attachment code, fortunately!
release_region(client->addr,LM78_EXTENT);
/* HYBRID SENSORS CHIP ONLY END */
kfree(data);
kfree(i2c_get_clientdata(client));
return 0;
}
......
DCCP protocol
============
Last updated: 10 November 2005
Contents
========
- Introduction
- Missing features
- Socket options
- Notes
Introduction
============
Datagram Congestion Control Protocol (DCCP) is an unreliable, connection
based protocol designed to solve issues present in UDP and TCP particularly
for real time and multimedia traffic.
It has a base protocol and pluggable congestion control IDs (CCIDs).
It is at draft RFC status and the homepage for DCCP as a protocol is at:
http://www.icir.org/kohler/dcp/
Missing features
================
The DCCP implementation does not currently have all the features that are in
the draft RFC.
In particular the following are missing:
- CCID2 support
- feature negotiation
When testing against other implementations it appears that elapsed time
options are not coded compliant to the specification.
Socket options
==============
DCCP_SOCKOPT_PACKET_SIZE is used for CCID3 to set default packet size for
calculations.
DCCP_SOCKOPT_SERVICE sets the service. This is compulsory as per the
specification. If you don't set it you will get EPROTO.
Notes
=====
SELinux does not yet have support for DCCP. You will need to turn it off or
else you will get EACCES.
DCCP does not travel through NAT successfully at present. This is because
the checksum covers the psuedo-header as per TCP and UDP. It should be
relatively trivial to add Linux NAT support for DCCP.
......@@ -707,7 +707,7 @@ DCCP PROTOCOL
P: Arnaldo Carvalho de Melo
M: acme@mandriva.com
L: dccp@vger.kernel.org
W: http://www.wlug.org.nz/DCCP
W: http://linux-net.osdl.org/index.php/DCCP
S: Maintained
DECnet NETWORK LAYER
......
......@@ -347,7 +347,7 @@ AFLAGS_KERNEL =
# Needed to be compatible with the O= option
LINUXINCLUDE := -Iinclude \
$(if $(KBUILD_SRC),-Iinclude2 -I$(srctree)/include) \
-imacros include/linux/autoconf.h
-include include/linux/autoconf.h
CPPFLAGS := -D__KERNEL__ $(LINUXINCLUDE)
......@@ -407,7 +407,7 @@ outputmakefile:
# of make so .config is not included in this case either (for *config).
no-dot-config-targets := clean mrproper distclean \
cscope TAGS tags help %docs check%
cscope TAGS tags help %docs check% kernelrelease
config-targets := 0
mixed-targets := 0
......
......@@ -239,6 +239,8 @@ source "arch/arm/plat-omap/Kconfig"
source "arch/arm/mach-omap1/Kconfig"
source "arch/arm/mach-omap2/Kconfig"
source "arch/arm/mach-s3c2410/Kconfig"
source "arch/arm/mach-lh7a40x/Kconfig"
......
......@@ -93,6 +93,7 @@ textaddr-$(CONFIG_ARCH_FORTUNET) := 0xc0008000
machine-$(CONFIG_ARCH_IXP4XX) := ixp4xx
machine-$(CONFIG_ARCH_IXP2000) := ixp2000
machine-$(CONFIG_ARCH_OMAP1) := omap1
machine-$(CONFIG_ARCH_OMAP2) := omap2
incdir-$(CONFIG_ARCH_OMAP) := omap
machine-$(CONFIG_ARCH_S3C2410) := s3c2410
machine-$(CONFIG_ARCH_LH7A40X) := lh7a40x
......
#
# Automatically generated make config: don't edit
# Linux kernel version: 2.6.13
# Mon Sep 5 18:07:12 2005
# Linux kernel version: 2.6.14
# Wed Nov 9 18:53:40 2005
#
CONFIG_ARM=y
CONFIG_MMU=y
......@@ -22,6 +22,7 @@ CONFIG_INIT_ENV_ARG_LIMIT=32
# General setup
#
CONFIG_LOCALVERSION=""
CONFIG_LOCALVERSION_AUTO=y
CONFIG_SWAP=y
CONFIG_SYSVIPC=y
# CONFIG_POSIX_MQUEUE is not set
......@@ -31,6 +32,7 @@ CONFIG_SYSCTL=y
# CONFIG_HOTPLUG is not set
CONFIG_KOBJECT_UEVENT=y
# CONFIG_IKCONFIG is not set
CONFIG_INITRAMFS_SOURCE=""
# CONFIG_EMBEDDED is not set
CONFIG_KALLSYMS=y
# CONFIG_KALLSYMS_EXTRA_PASS is not set
......@@ -59,6 +61,23 @@ CONFIG_OBSOLETE_MODPARM=y
# CONFIG_MODULE_SRCVERSION_ALL is not set
# CONFIG_KMOD is not set
#
# Block layer
#
#
# IO Schedulers
#
CONFIG_IOSCHED_NOOP=y
CONFIG_IOSCHED_AS=y
CONFIG_IOSCHED_DEADLINE=y
CONFIG_IOSCHED_CFQ=y
CONFIG_DEFAULT_AS=y
# CONFIG_DEFAULT_DEADLINE is not set
# CONFIG_DEFAULT_CFQ is not set
# CONFIG_DEFAULT_NOOP is not set
CONFIG_DEFAULT_IOSCHED="anticipatory"
#
# System Type
#
......@@ -81,6 +100,7 @@ CONFIG_OBSOLETE_MODPARM=y
# CONFIG_ARCH_LH7A40X is not set
CONFIG_ARCH_OMAP=y
# CONFIG_ARCH_VERSATILE is not set
# CONFIG_ARCH_REALVIEW is not set
# CONFIG_ARCH_IMX is not set
# CONFIG_ARCH_H720X is not set
# CONFIG_ARCH_AAEC2000 is not set
......@@ -112,7 +132,7 @@ CONFIG_OMAP_SERIAL_WAKE=y
# OMAP Core Type
#
# CONFIG_ARCH_OMAP730 is not set
# CONFIG_ARCH_OMAP1510 is not set
# CONFIG_ARCH_OMAP15XX is not set
CONFIG_ARCH_OMAP16XX=y
#
......@@ -177,6 +197,8 @@ CONFIG_FLATMEM_MANUAL=y
# CONFIG_SPARSEMEM_MANUAL is not set
CONFIG_FLATMEM=y
CONFIG_FLAT_NODE_MEM_MAP=y
# CONFIG_SPARSEMEM_STATIC is not set
CONFIG_SPLIT_PTLOCK_CPUS=4096
# CONFIG_LEDS is not set
CONFIG_ALIGNMENT_TRAP=y
......@@ -258,13 +280,18 @@ CONFIG_IP_PNP_BOOTP=y
# CONFIG_INET_ESP is not set
# CONFIG_INET_IPCOMP is not set
# CONFIG_INET_TUNNEL is not set
CONFIG_IP_TCPDIAG=y
# CONFIG_IP_TCPDIAG_IPV6 is not set
CONFIG_INET_DIAG=y
CONFIG_INET_TCP_DIAG=y
# CONFIG_TCP_CONG_ADVANCED is not set
CONFIG_TCP_CONG_BIC=y
# CONFIG_IPV6 is not set
# CONFIG_NETFILTER is not set
#
# DCCP Configuration (EXPERIMENTAL)
#
# CONFIG_IP_DCCP is not set
#
# SCTP Configuration (EXPERIMENTAL)
#
......@@ -281,6 +308,10 @@ CONFIG_TCP_CONG_BIC=y
# CONFIG_NET_DIVERT is not set
# CONFIG_ECONET is not set
# CONFIG_WAN_ROUTER is not set
#
# QoS and/or fair queueing
#
# CONFIG_NET_SCHED is not set
# CONFIG_NET_CLS_ROUTE is not set
......@@ -291,6 +322,7 @@ CONFIG_TCP_CONG_BIC=y
# CONFIG_HAMRADIO is not set
# CONFIG_IRDA is not set
# CONFIG_BT is not set
# CONFIG_IEEE80211 is not set
#
# Device Drivers
......@@ -328,21 +360,13 @@ CONFIG_BLK_DEV_RAM=y
CONFIG_BLK_DEV_RAM_COUNT=16
CONFIG_BLK_DEV_RAM_SIZE=8192
CONFIG_BLK_DEV_INITRD=y
CONFIG_INITRAMFS_SOURCE=""
# CONFIG_CDROM_PKTCDVD is not set
#
# IO Schedulers
#
CONFIG_IOSCHED_NOOP=y
CONFIG_IOSCHED_AS=y
CONFIG_IOSCHED_DEADLINE=y
CONFIG_IOSCHED_CFQ=y
CONFIG_ATA_OVER_ETH=m
#
# SCSI device support
#
# CONFIG_RAID_ATTRS is not set
CONFIG_SCSI=y
CONFIG_SCSI_PROC_FS=y
......@@ -369,10 +393,12 @@ CONFIG_SCSI_PROC_FS=y
# CONFIG_SCSI_SPI_ATTRS is not set
# CONFIG_SCSI_FC_ATTRS is not set
# CONFIG_SCSI_ISCSI_ATTRS is not set
# CONFIG_SCSI_SAS_ATTRS is not set
#
# SCSI low-level drivers
#
# CONFIG_ISCSI_TCP is not set
# CONFIG_SCSI_SATA is not set
# CONFIG_SCSI_DEBUG is not set
......@@ -403,6 +429,11 @@ CONFIG_NETDEVICES=y
# CONFIG_EQUALIZER is not set
# CONFIG_TUN is not set
#
# PHY device support
#
# CONFIG_PHYLIB is not set
#
# Ethernet (10 or 100Mbit)
#
......@@ -439,6 +470,7 @@ CONFIG_PPP=y
# CONFIG_PPP_SYNC_TTY is not set
# CONFIG_PPP_DEFLATE is not set
# CONFIG_PPP_BSDCOMP is not set
# CONFIG_PPP_MPPE is not set
# CONFIG_PPPOE is not set
CONFIG_SLIP=y
CONFIG_SLIP_COMPRESSED=y
......@@ -541,24 +573,28 @@ CONFIG_WATCHDOG_NOWAYOUT=y
#
# TPM devices
#
# CONFIG_TELCLOCK is not set
#
# I2C support
#
# CONFIG_I2C is not set
# CONFIG_I2C_SENSOR is not set
CONFIG_ISP1301_OMAP=y
#
# Hardware Monitoring support
#
CONFIG_HWMON=y
# CONFIG_HWMON_VID is not set
# CONFIG_HWMON_DEBUG_CHIP is not set
#
# Misc devices
#
#
# Multimedia Capabilities Port drivers
#
#
# Multimedia devices
#
......@@ -576,7 +612,6 @@ CONFIG_FB=y
# CONFIG_FB_CFB_FILLRECT is not set
# CONFIG_FB_CFB_COPYAREA is not set
# CONFIG_FB_CFB_IMAGEBLIT is not set
# CONFIG_FB_SOFT_CURSOR is not set
# CONFIG_FB_MACMODES is not set
CONFIG_FB_MODE_HELPERS=y
# CONFIG_FB_TILEBLITTING is not set
......@@ -589,6 +624,7 @@ CONFIG_FB_MODE_HELPERS=y
# CONFIG_VGA_CONSOLE is not set
CONFIG_DUMMY_CONSOLE=y
CONFIG_FRAMEBUFFER_CONSOLE=y
# CONFIG_FRAMEBUFFER_CONSOLE_ROTATION is not set
CONFIG_FONTS=y
CONFIG_FONT_8x8=y
CONFIG_FONT_8x16=y
......@@ -600,6 +636,7 @@ CONFIG_FONT_8x16=y
# CONFIG_FONT_SUN8x16 is not set
# CONFIG_FONT_SUN12x22 is not set
# CONFIG_FONT_10x18 is not set
# CONFIG_FONT_RL is not set
#
# Logo configuration
......@@ -624,10 +661,10 @@ CONFIG_SOUND=y
# Open Sound System
#
CONFIG_SOUND_PRIME=y
# CONFIG_OBSOLETE_OSS_DRIVER is not set
# CONFIG_SOUND_MSNDCLAS is not set
# CONFIG_SOUND_MSNDPIN is not set
# CONFIG_SOUND_OSS is not set
# CONFIG_SOUND_AD1980 is not set
#
# USB support
......@@ -636,23 +673,22 @@ CONFIG_USB_ARCH_HAS_HCD=y
CONFIG_USB_ARCH_HAS_OHCI=y
# CONFIG_USB is not set
#
# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
#
#
# USB Gadget Support
#
CONFIG_USB_GADGET=y
# CONFIG_USB_GADGET_DEBUG_FILES is not set
CONFIG_USB_GADGET_SELECTED=y
# CONFIG_USB_GADGET is not set
# CONFIG_USB_GADGET_NET2280 is not set
# CONFIG_USB_GADGET_PXA2XX is not set
# CONFIG_USB_GADGET_GOKU is not set
# CONFIG_USB_GADGET_LH7A40X is not set
CONFIG_USB_GADGET_OMAP=y
CONFIG_USB_OMAP=y
# CONFIG_USB_GADGET_OMAP is not set
# CONFIG_USB_GADGET_DUMMY_HCD is not set
# CONFIG_USB_GADGET_DUALSPEED is not set
# CONFIG_USB_ZERO is not set
CONFIG_USB_ETH=y
CONFIG_USB_ETH_RNDIS=y
# CONFIG_USB_ETH is not set
# CONFIG_USB_GADGETFS is not set
# CONFIG_USB_FILE_STORAGE is not set
# CONFIG_USB_G_SERIAL is not set
......@@ -673,10 +709,6 @@ CONFIG_EXT2_FS=y
# CONFIG_REISERFS_FS is not set
# CONFIG_JFS_FS is not set
# CONFIG_FS_POSIX_ACL is not set
#
# XFS support
#
# CONFIG_XFS_FS is not set
# CONFIG_MINIX_FS is not set
CONFIG_ROMFS_FS=y
......@@ -685,6 +717,7 @@ CONFIG_INOTIFY=y
CONFIG_DNOTIFY=y
# CONFIG_AUTOFS_FS is not set
# CONFIG_AUTOFS4_FS is not set
# CONFIG_FUSE_FS is not set
#
# CD-ROM/DVD Filesystems
......@@ -706,10 +739,10 @@ CONFIG_FAT_DEFAULT_CODEPAGE=437
#
CONFIG_PROC_FS=y
CONFIG_SYSFS=y
# CONFIG_DEVPTS_FS_XATTR is not set
# CONFIG_TMPFS is not set
# CONFIG_HUGETLB_PAGE is not set
CONFIG_RAMFS=y
# CONFIG_RELAYFS_FS is not set
#
# Miscellaneous filesystems
......@@ -750,6 +783,7 @@ CONFIG_RPCSEC_GSS_KRB5=y
# CONFIG_NCP_FS is not set
# CONFIG_CODA_FS is not set
# CONFIG_AFS_FS is not set
# CONFIG_9P_FS is not set
#
# Partition Types
......@@ -859,6 +893,7 @@ CONFIG_CRYPTO_DES=y
# Library routines
#
# CONFIG_CRC_CCITT is not set
# CONFIG_CRC16 is not set
CONFIG_CRC32=y
# CONFIG_LIBCRC32C is not set
CONFIG_ZLIB_INFLATE=y
......@@ -39,6 +39,7 @@ td3 .req lr
/* we must have at least one byte. */
tst buf, #1 @ odd address?
movne sum, sum, ror #8
ldrneb td0, [buf], #1
subne len, len, #1
adcnes sum, sum, td0, put_byte_1
......@@ -103,6 +104,9 @@ ENTRY(csum_partial)
cmp len, #8 @ Ensure that we have at least
blo .less8 @ 8 bytes to copy.
tst buf, #1
movne sum, sum, ror #8
adds sum, sum, #0 @ C = 0
tst buf, #3 @ Test destination alignment
blne .not_aligned @ aligh destination, return here
......
......@@ -8,6 +8,16 @@ menu "Intel IXP4xx Implementation Options"
comment "IXP4xx Platforms"
# This entry is placed on top because otherwise it would have
# been shown as a submenu.
config MACH_NSLU2
bool
prompt "NSLU2" if !(MACH_IXDP465 || MACH_IXDPG425 || ARCH_IXDP425 || ARCH_ADI_COYOTE || ARCH_AVILA || ARCH_IXCDP1100 || ARCH_PRPMC1100 || MACH_GTWX5715)
help
Say 'Y' here if you want your kernel to support Linksys's
NSLU2 NAS device. For more information on this platform,
see http://www.nslu2-linux.org
config ARCH_AVILA
bool "Avila"
help
......
......@@ -8,4 +8,5 @@ obj-$(CONFIG_ARCH_IXDP4XX) += ixdp425-pci.o ixdp425-setup.o
obj-$(CONFIG_MACH_IXDPG425) += ixdpg425-pci.o coyote-setup.o
obj-$(CONFIG_ARCH_ADI_COYOTE) += coyote-pci.o coyote-setup.o
obj-$(CONFIG_MACH_GTWX5715) += gtwx5715-pci.o gtwx5715-setup.o
obj-$(CONFIG_MACH_NSLU2) += nslu2-pci.o nslu2-setup.o nslu2-power.o
/*
* arch/arm/mach-ixp4xx/nslu2-pci.c
*
* NSLU2 board-level PCI initialization
*
* based on ixdp425-pci.c:
* Copyright (C) 2002 Intel Corporation.
* Copyright (C) 2003-2004 MontaVista Software, Inc.
*
* Maintainer: http://www.nslu2-linux.org/
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*
*/
#include <linux/config.h>
#include <linux/pci.h>
#include <linux/init.h>
#include <asm/mach/pci.h>
#include <asm/mach-types.h>
void __init nslu2_pci_preinit(void)
{
set_irq_type(IRQ_NSLU2_PCI_INTA, IRQT_LOW);
set_irq_type(IRQ_NSLU2_PCI_INTB, IRQT_LOW);
set_irq_type(IRQ_NSLU2_PCI_INTC, IRQT_LOW);
gpio_line_isr_clear(NSLU2_PCI_INTA_PIN);
gpio_line_isr_clear(NSLU2_PCI_INTB_PIN);
gpio_line_isr_clear(NSLU2_PCI_INTC_PIN);
/* INTD is not configured as GPIO is used
* for the power input button.
*/
ixp4xx_pci_preinit();
}
static int __init nslu2_map_irq(struct pci_dev *dev, u8 slot, u8 pin)
{
static int pci_irq_table[NSLU2_PCI_IRQ_LINES] = {
IRQ_NSLU2_PCI_INTA,
IRQ_NSLU2_PCI_INTB,
IRQ_NSLU2_PCI_INTC,
};
int irq = -1;
if (slot >= 1 && slot <= NSLU2_PCI_MAX_DEV &&
pin >= 1 && pin <= NSLU2_PCI_IRQ_LINES) {
irq = pci_irq_table[(slot + pin - 2) % NSLU2_PCI_IRQ_LINES];
}
return irq;
}
struct hw_pci __initdata nslu2_pci = {
.nr_controllers = 1,
.preinit = nslu2_pci_preinit,
.swizzle = pci_std_swizzle,
.setup = ixp4xx_setup,
.scan = ixp4xx_scan_bus,
.map_irq = nslu2_map_irq,
};
int __init nslu2_pci_init(void) /* monkey see, monkey do */
{
if (machine_is_nslu2())
pci_common_init(&nslu2_pci);
return 0;
}
subsys_initcall(nslu2_pci_init);
/*
* arch/arm/mach-ixp4xx/nslu2-power.c
*
* NSLU2 Power/Reset driver
*
* Copyright (C) 2005 Tower Technologies
*
* based on nslu2-io.c
* Copyright (C) 2004 Karen Spearel
*
* Author: Alessandro Zummo <a.zummo@towertech.it>
* Maintainers: http://www.nslu2-linux.org/
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*
*/
#include <linux/module.h>
#include <linux/reboot.h>
#include <linux/interrupt.h>
#include <asm/mach-types.h>
extern void ctrl_alt_del(void);
static irqreturn_t nslu2_power_handler(int irq, void *dev_id, struct pt_regs *regs)
{
/* Signal init to do the ctrlaltdel action, this will bypass init if
* it hasn't started and do a kernel_restart.
*/
ctrl_alt_del();
return IRQ_HANDLED;
}
static irqreturn_t nslu2_reset_handler(int irq, void *dev_id, struct pt_regs *regs)
{
/* This is the paper-clip reset, it shuts the machine down directly.
*/
machine_power_off();
return IRQ_HANDLED;
}
static int __init nslu2_power_init(void)
{
if (!(machine_is_nslu2()))
return 0;
*IXP4XX_GPIO_GPISR = 0x20400000; /* read the 2 irqs to clr */
set_irq_type(NSLU2_RB_IRQ, IRQT_LOW);
set_irq_type(NSLU2_PB_IRQ, IRQT_HIGH);
gpio_line_isr_clear(NSLU2_RB_GPIO);
gpio_line_isr_clear(NSLU2_PB_GPIO);
if (request_irq(NSLU2_RB_IRQ, &nslu2_reset_handler,
SA_INTERRUPT, "NSLU2 reset button", NULL) < 0) {
printk(KERN_DEBUG "Reset Button IRQ %d not available\n",
NSLU2_RB_IRQ);
return -EIO;
}
if (request_irq(NSLU2_PB_IRQ, &nslu2_power_handler,
SA_INTERRUPT, "NSLU2 power button", NULL) < 0) {
printk(KERN_DEBUG "Power Button IRQ %d not available\n",
NSLU2_PB_IRQ);
return -EIO;
}
return 0;
}
static void __exit nslu2_power_exit(void)
{
free_irq(NSLU2_RB_IRQ, NULL);
free_irq(NSLU2_PB_IRQ, NULL);
}
module_init(nslu2_power_init);
module_exit(nslu2_power_exit);
MODULE_AUTHOR("Alessandro Zummo <a.zummo@towertech.it>");
MODULE_DESCRIPTION("NSLU2 Power/Reset driver");
MODULE_LICENSE("GPL");
/*
* arch/arm/mach-ixp4xx/nslu2-setup.c
*
* NSLU2 board-setup
*
* based ixdp425-setup.c:
* Copyright (C) 2003-2004 MontaVista Software, Inc.
*
* Author: Mark Rakes <mrakes at mac.com>
* Maintainers: http://www.nslu2-linux.org/
*
* Fixed missing init_time in MACHINE_START kas11 10/22/04
* Changed to conform to new style __init ixdp425 kas11 10/22/04
*/
#include <linux/kernel.h>
#include <linux/serial.h>
#include <linux/serial_8250.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/flash.h>
static struct flash_platform_data nslu2_flash_data = {
.map_name = "cfi_probe",
.width = 2,
};
static struct resource nslu2_flash_resource = {
.start = NSLU2_FLASH_BASE,
.end = NSLU2_FLASH_BASE + NSLU2_FLASH_SIZE,
.flags = IORESOURCE_MEM,
};
static struct platform_device nslu2_flash = {
.name = "IXP4XX-Flash",
.id = 0,
.dev.platform_data = &nslu2_flash_data,
.num_resources = 1,
.resource = &nslu2_flash_resource,
};
static struct ixp4xx_i2c_pins nslu2_i2c_gpio_pins = {
.sda_pin = NSLU2_SDA_PIN,
.scl_pin = NSLU2_SCL_PIN,
};
static struct platform_device nslu2_i2c_controller = {
.name = "IXP4XX-I2C",
.id = 0,
.dev.platform_data = &nslu2_i2c_gpio_pins,
.num_resources = 0,
};
static struct resource nslu2_uart_resources[] = {
{
.start = IXP4XX_UART1_BASE_PHYS,
.end = IXP4XX_UART1_BASE_PHYS + 0x0fff,
.flags = IORESOURCE_MEM,
},
{
.start = IXP4XX_UART2_BASE_PHYS,
.end = IXP4XX_UART2_BASE_PHYS + 0x0fff,
.flags = IORESOURCE_MEM,
}
};
static struct plat_serial8250_port nslu2_uart_data[] = {
{
.mapbase = IXP4XX_UART1_BASE_PHYS,
.membase = (char *)IXP4XX_UART1_BASE_VIRT + REG_OFFSET,
.irq = IRQ_IXP4XX_UART1,
.flags = UPF_BOOT_AUTOCONF,
.iotype = UPIO_MEM,
.regshift = 2,
.uartclk = IXP4XX_UART_XTAL,
},
{
.mapbase = IXP4XX_UART2_BASE_PHYS,
.membase = (char *)IXP4XX_UART2_BASE_VIRT + REG_OFFSET,
.irq = IRQ_IXP4XX_UART2,
.flags = UPF_BOOT_AUTOCONF,
.iotype = UPIO_MEM,
.regshift = 2,
.uartclk = IXP4XX_UART_XTAL,
},
{ }
};
static struct platform_device nslu2_uart = {
.name = "serial8250",
.id = PLAT8250_DEV_PLATFORM,
.dev.platform_data = nslu2_uart_data,
.num_resources = 2,
.resource = nslu2_uart_resources,
};
static struct platform_device *nslu2_devices[] __initdata = {
&nslu2_i2c_controller,
&nslu2_flash,
&nslu2_uart,
};
static void nslu2_power_off(void)
{
/* This causes the box to drop the power and go dead. */
/* enable the pwr cntl gpio */
gpio_line_config(NSLU2_PO_GPIO, IXP4XX_GPIO_OUT);
/* do the deed */
gpio_line_set(NSLU2_PO_GPIO, IXP4XX_GPIO_HIGH);
}
static void __init nslu2_init(void)
{
ixp4xx_sys_init();
pm_power_off = nslu2_power_off;
platform_add_devices(nslu2_devices, ARRAY_SIZE(nslu2_devices));
}
MACHINE_START(NSLU2, "Linksys NSLU2")
/* Maintainer: www.nslu2-linux.org */
.phys_ram = PHYS_OFFSET,
.phys_io = IXP4XX_PERIPHERAL_BASE_PHYS,
.io_pg_offst = ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xFFFC,
.boot_params = 0x00000100,
.map_io = ixp4xx_map_io,
.init_irq = ixp4xx_init_irq,
.timer = &ixp4xx_timer,
.init_machine = nslu2_init,
MACHINE_END
......@@ -6,10 +6,10 @@ config ARCH_OMAP730
bool "OMAP730 Based System"
select ARCH_OMAP_OTG
config ARCH_OMAP1510
config ARCH_OMAP15XX
depends on ARCH_OMAP1
default y
bool "OMAP1510 Based System"
bool "OMAP15xx Based System"
config ARCH_OMAP16XX
depends on ARCH_OMAP1
......@@ -21,7 +21,7 @@ comment "OMAP Board Type"
config MACH_OMAP_INNOVATOR
bool "TI Innovator"
depends on ARCH_OMAP1 && (ARCH_OMAP1510 || ARCH_OMAP16XX)
depends on ARCH_OMAP1 && (ARCH_OMAP15XX || ARCH_OMAP16XX)
help
TI OMAP 1510 or 1610 Innovator board support. Say Y here if you
have such a board.
......@@ -64,20 +64,30 @@ config MACH_OMAP_PERSEUS2
config MACH_VOICEBLUE
bool "Voiceblue"
depends on ARCH_OMAP1 && ARCH_OMAP1510
depends on ARCH_OMAP1 && ARCH_OMAP15XX
help
Support for Voiceblue GSM/VoIP gateway. Say Y here if you have
such a board.
config MACH_NETSTAR
bool "NetStar"
depends on ARCH_OMAP1 && ARCH_OMAP1510
depends on ARCH_OMAP1 && ARCH_OMAP15XX
help
Support for NetStar PBX. Say Y here if you have such a board.
config MACH_OMAP_PALMTE
bool "Palm Tungsten E"
depends on ARCH_OMAP1 && ARCH_OMAP15XX
help
Support for the Palm Tungsten E PDA. Currently only the LCD panel
is supported. To boot the kernel, you'll need a PalmOS compatible
bootloader; check out http://palmtelinux.sourceforge.net for more
informations.
Say Y here if you have such a PDA, say NO otherwise.
config MACH_OMAP_GENERIC
bool "Generic OMAP board"
depends on ARCH_OMAP1 && (ARCH_OMAP1510 || ARCH_OMAP16XX)
depends on ARCH_OMAP1 && (ARCH_OMAP15XX || ARCH_OMAP16XX)
help
Support for generic OMAP-1510, 1610 or 1710 board with
no FPGA. Can be used as template for porting Linux to
......@@ -121,32 +131,32 @@ config OMAP_ARM_182MHZ
config OMAP_ARM_168MHZ
bool "OMAP ARM 168 MHz CPU"
depends on ARCH_OMAP1 && (ARCH_OMAP1510 || ARCH_OMAP16XX || ARCH_OMAP730)
depends on ARCH_OMAP1 && (ARCH_OMAP15XX || ARCH_OMAP16XX || ARCH_OMAP730)
help
Enable 168MHz clock for OMAP CPU. If unsure, say N.
config OMAP_ARM_150MHZ
bool "OMAP ARM 150 MHz CPU"
depends on ARCH_OMAP1 && ARCH_OMAP1510
depends on ARCH_OMAP1 && ARCH_OMAP15XX
help
Enable 150MHz clock for OMAP CPU. If unsure, say N.
config OMAP_ARM_120MHZ
bool "OMAP ARM 120 MHz CPU"
depends on ARCH_OMAP1 && (ARCH_OMAP1510 || ARCH_OMAP16XX || ARCH_OMAP730)
depends on ARCH_OMAP1 && (ARCH_OMAP15XX || ARCH_OMAP16XX || ARCH_OMAP730)
help
Enable 120MHz clock for OMAP CPU. If unsure, say N.
config OMAP_ARM_60MHZ
bool "OMAP ARM 60 MHz CPU"
depends on ARCH_OMAP1 && (ARCH_OMAP1510 || ARCH_OMAP16XX || ARCH_OMAP730)
depends on ARCH_OMAP1 && (ARCH_OMAP15XX || ARCH_OMAP16XX || ARCH_OMAP730)
default y
help
Enable 60MHz clock for OMAP CPU. If unsure, say Y.
config OMAP_ARM_30MHZ
bool "OMAP ARM 30 MHz CPU"
depends on ARCH_OMAP1 && (ARCH_OMAP1510 || ARCH_OMAP16XX || ARCH_OMAP730)
depends on ARCH_OMAP1 && (ARCH_OMAP15XX || ARCH_OMAP16XX || ARCH_OMAP730)
help
Enable 30MHz clock for OMAP CPU. If unsure, say N.
......@@ -3,7 +3,7 @@
#
# Common support
obj-y := io.o id.o irq.o time.o serial.o devices.o
obj-y := io.o id.o clock.o irq.o time.o mux.o serial.o devices.o
led-y := leds.o
# Specific board support
......@@ -15,8 +15,9 @@ obj-$(CONFIG_MACH_OMAP_OSK) += board-osk.o
obj-$(CONFIG_MACH_OMAP_H3) += board-h3.o
obj-$(CONFIG_MACH_VOICEBLUE) += board-voiceblue.o
obj-$(CONFIG_MACH_NETSTAR) += board-netstar.o
obj-$(CONFIG_MACH_OMAP_PALMTE) += board-palmte.o
ifeq ($(CONFIG_ARCH_OMAP1510),y)
ifeq ($(CONFIG_ARCH_OMAP15XX),y)
# Innovator-1510 FPGA
obj-$(CONFIG_MACH_OMAP_INNOVATOR) += fpga.o
endif
......
......@@ -15,7 +15,7 @@
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/device.h>
#include <linux/platform_device.h>
#include <asm/hardware.h>
#include <asm/mach-types.h>
......@@ -28,8 +28,6 @@
#include <asm/arch/board.h>
#include <asm/arch/common.h>
static int __initdata generic_serial_ports[OMAP_MAX_NR_PORTS] = {1, 1, 1};
static void __init omap_generic_init_irq(void)
{
omap_init_irq();
......@@ -37,7 +35,7 @@ static void __init omap_generic_init_irq(void)
/* assume no Mini-AB port */
#ifdef CONFIG_ARCH_OMAP1510
#ifdef CONFIG_ARCH_OMAP15XX
static struct omap_usb_config generic1510_usb_config __initdata = {
.register_host = 1,
.register_dev = 1,
......@@ -76,21 +74,19 @@ static struct omap_mmc_config generic_mmc_config __initdata = {
#endif
static struct omap_uart_config generic_uart_config __initdata = {
.enabled_uarts = ((1 << 0) | (1 << 1) | (1 << 2)),
};
static struct omap_board_config_kernel generic_config[] = {
{ OMAP_TAG_USB, NULL },
{ OMAP_TAG_MMC, &generic_mmc_config },
{ OMAP_TAG_UART, &generic_uart_config },
};
static void __init omap_generic_init(void)
{
const struct omap_uart_config *uart_conf;
/*
* Make sure the serial ports are muxed on at this point.
* You have to mux them off in device drivers later on
* if not needed.
*/
#ifdef CONFIG_ARCH_OMAP1510
#ifdef CONFIG_ARCH_OMAP15XX
if (cpu_is_omap1510()) {
generic_config[0].data = &generic1510_usb_config;
}
......@@ -101,20 +97,9 @@ static void __init omap_generic_init(void)
}
#endif
uart_conf = omap_get_config(OMAP_TAG_UART, struct omap_uart_config);
if (uart_conf != NULL) {
unsigned int enabled_ports, i;
enabled_ports = uart_conf->enabled_uarts;
for (i = 0; i < 3; i++) {
if (!(enabled_ports & (1 << i)))
generic_serial_ports[i] = 0;
}
}
omap_board_config = generic_config;
omap_board_config_size = ARRAY_SIZE(generic_config);
omap_serial_init(generic_serial_ports);
omap_serial_init();
}
static void __init omap_generic_map_io(void)
......
......@@ -40,8 +40,6 @@
extern int omap_gpio_init(void);
static int __initdata h2_serial_ports[OMAP_MAX_NR_PORTS] = {1, 1, 1};
static struct mtd_partition h2_partitions[] = {
/* bootloader (U-Boot, etc) in first sector */
{
......@@ -160,9 +158,20 @@ static struct omap_mmc_config h2_mmc_config __initdata = {
},
};
static struct omap_uart_config h2_uart_config __initdata = {
.enabled_uarts = ((1 << 0) | (1 << 1) | (1 << 2)),
};
static struct omap_lcd_config h2_lcd_config __initdata = {
.panel_name = "h2",
.ctrl_name = "internal",
};
static struct omap_board_config_kernel h2_config[] = {
{ OMAP_TAG_USB, &h2_usb_config },
{ OMAP_TAG_MMC, &h2_mmc_config },
{ OMAP_TAG_UART, &h2_uart_config },
{ OMAP_TAG_LCD, &h2_lcd_config },
};
static void __init h2_init(void)
......@@ -180,12 +189,12 @@ static void __init h2_init(void)
platform_add_devices(h2_devices, ARRAY_SIZE(h2_devices));
omap_board_config = h2_config;
omap_board_config_size = ARRAY_SIZE(h2_config);
omap_serial_init();
}
static void __init h2_map_io(void)
{
omap_map_common_io();
omap_serial_init(h2_serial_ports);
}
MACHINE_START(OMAP_H2, "TI-H2")
......
......@@ -41,8 +41,6 @@
extern int omap_gpio_init(void);
static int __initdata h3_serial_ports[OMAP_MAX_NR_PORTS] = {1, 1, 1};
static struct mtd_partition h3_partitions[] = {
/* bootloader (U-Boot, etc) in first sector */
{
......@@ -168,9 +166,20 @@ static struct omap_mmc_config h3_mmc_config __initdata = {
},
};
static struct omap_uart_config h3_uart_config __initdata = {
.enabled_uarts = ((1 << 0) | (1 << 1) | (1 << 2)),
};
static struct omap_lcd_config h3_lcd_config __initdata = {
.panel_name = "h3",
.ctrl_name = "internal",
};
static struct omap_board_config_kernel h3_config[] = {
{ OMAP_TAG_USB, &h3_usb_config },
{ OMAP_TAG_MMC, &h3_mmc_config },
{ OMAP_TAG_USB, &h3_usb_config },
{ OMAP_TAG_MMC, &h3_mmc_config },
{ OMAP_TAG_UART, &h3_uart_config },
{ OMAP_TAG_LCD, &h3_lcd_config },
};
static void __init h3_init(void)
......@@ -180,6 +189,7 @@ static void __init h3_init(void)
(void) platform_add_devices(devices, ARRAY_SIZE(devices));
omap_board_config = h3_config;
omap_board_config_size = ARRAY_SIZE(h3_config);
omap_serial_init();
}
static void __init h3_init_smc91x(void)
......@@ -201,7 +211,6 @@ void h3_init_irq(void)
static void __init h3_map_io(void)
{
omap_map_common_io();
omap_serial_init(h3_serial_ports);
}
MACHINE_START(OMAP_H3, "TI OMAP1710 H3 board")
......
......@@ -36,8 +36,6 @@
#include <asm/arch/usb.h>
#include <asm/arch/common.h>
static int __initdata innovator_serial_ports[OMAP_MAX_NR_PORTS] = {1, 1, 1};
static struct mtd_partition innovator_partitions[] = {
/* bootloader (U-Boot, etc) in first sector */
{
......@@ -99,7 +97,7 @@ static struct platform_device innovator_flash_device = {
.resource = &innovator_flash_resource,
};
#ifdef CONFIG_ARCH_OMAP1510
#ifdef CONFIG_ARCH_OMAP15XX
/* Only FPGA needs to be mapped here. All others are done with ioremap */
static struct map_desc innovator1510_io_desc[] __initdata = {
......@@ -136,7 +134,7 @@ static struct platform_device *innovator1510_devices[] __initdata = {
&innovator1510_smc91x_device,
};
#endif /* CONFIG_ARCH_OMAP1510 */
#endif /* CONFIG_ARCH_OMAP15XX */
#ifdef CONFIG_ARCH_OMAP16XX
......@@ -185,7 +183,7 @@ void innovator_init_irq(void)
{
omap_init_irq();
omap_gpio_init();
#ifdef CONFIG_ARCH_OMAP1510
#ifdef CONFIG_ARCH_OMAP15XX
if (cpu_is_omap1510()) {
omap1510_fpga_init_irq();
}
......@@ -193,7 +191,7 @@ void innovator_init_irq(void)
innovator_init_smc91x();
}
#ifdef CONFIG_ARCH_OMAP1510
#ifdef CONFIG_ARCH_OMAP15XX
static struct omap_usb_config innovator1510_usb_config __initdata = {
/* for bundled non-standard host and peripheral cables */
.hmc_mode = 4,
......@@ -205,6 +203,11 @@ static struct omap_usb_config innovator1510_usb_config __initdata = {
.register_dev = 1,
.pins[0] = 2,
};
static struct omap_lcd_config innovator1510_lcd_config __initdata = {
.panel_name = "inn1510",
.ctrl_name = "internal",
};
#endif
#ifdef CONFIG_ARCH_OMAP16XX
......@@ -222,6 +225,11 @@ static struct omap_usb_config h2_usb_config __initdata = {
.pins[1] = 3,
};
static struct omap_lcd_config innovator1610_lcd_config __initdata = {
.panel_name = "inn1610",
.ctrl_name = "internal",
};
#endif
static struct omap_mmc_config innovator_mmc_config __initdata = {
......@@ -234,14 +242,20 @@ static struct omap_mmc_config innovator_mmc_config __initdata = {
},
};
static struct omap_uart_config innovator_uart_config __initdata = {
.enabled_uarts = ((1 << 0) | (1 << 1) | (1 << 2)),
};
static struct omap_board_config_kernel innovator_config[] = {
{ OMAP_TAG_USB, NULL },
{ OMAP_TAG_LCD, NULL },
{ OMAP_TAG_MMC, &innovator_mmc_config },
{ OMAP_TAG_UART, &innovator_uart_config },
};
static void __init innovator_init(void)
{
#ifdef CONFIG_ARCH_OMAP1510
#ifdef CONFIG_ARCH_OMAP15XX
if (cpu_is_omap1510()) {
platform_add_devices(innovator1510_devices, ARRAY_SIZE(innovator1510_devices));
}
......@@ -252,23 +266,28 @@ static void __init innovator_init(void)
}
#endif
#ifdef CONFIG_ARCH_OMAP1510
if (cpu_is_omap1510())
#ifdef CONFIG_ARCH_OMAP15XX
if (cpu_is_omap1510()) {
innovator_config[0].data = &innovator1510_usb_config;
innovator_config[1].data = &innovator1510_lcd_config;
}
#endif
#ifdef CONFIG_ARCH_OMAP16XX
if (cpu_is_omap1610())
if (cpu_is_omap1610()) {
innovator_config[0].data = &h2_usb_config;
innovator_config[1].data = &innovator1610_lcd_config;
}
#endif
omap_board_config = innovator_config;
omap_board_config_size = ARRAY_SIZE(innovator_config);
omap_serial_init();
}
static void __init innovator_map_io(void)
{
omap_map_common_io();
#ifdef CONFIG_ARCH_OMAP1510
#ifdef CONFIG_ARCH_OMAP15XX
if (cpu_is_omap1510()) {
iotable_init(innovator1510_io_desc, ARRAY_SIZE(innovator1510_io_desc));
udelay(10); /* Delay needed for FPGA */
......@@ -280,7 +299,6 @@ static void __init innovator_map_io(void)
fpga_read(OMAP1510_FPGA_BOARD_REV));
}
#endif
omap_serial_init(innovator_serial_ports);
}
MACHINE_START(OMAP_INNOVATOR, "TI-Innovator")
......
......@@ -55,6 +55,14 @@ static struct platform_device *netstar_devices[] __initdata = {
&netstar_smc91x_device,
};
static struct omap_uart_config netstar_uart_config __initdata = {
.enabled_uarts = ((1 << 0) | (1 << 1) | (1 << 2)),
};
static struct omap_board_config_kernel netstar_config[] = {
{ OMAP_TAG_UART, &netstar_uart_config },
};
static void __init netstar_init_irq(void)
{
omap_init_irq();
......@@ -92,14 +100,15 @@ static void __init netstar_init(void)
/* Switch off red LED */
omap_writeb(0x00, OMAP_LPG1_PMR); /* Disable clock */
omap_writeb(0x80, OMAP_LPG1_LCR);
}
static int __initdata omap_serial_ports[OMAP_MAX_NR_PORTS] = {1, 1, 1};
omap_board_config = netstar_config;
omap_board_config_size = ARRAY_SIZE(netstar_config);
omap_serial_init();
}
static void __init netstar_map_io(void)
{
omap_map_common_io();
omap_serial_init(omap_serial_ports);
}
#define MACHINE_PANICED 1
......
......@@ -46,8 +46,6 @@
#include <asm/arch/tc.h>
#include <asm/arch/common.h>
static int __initdata osk_serial_ports[OMAP_MAX_NR_PORTS] = {1, 0, 0};
static struct mtd_partition osk_partitions[] = {
/* bootloader (U-Boot, etc) in first sector */
{
......@@ -155,7 +153,7 @@ static void __init osk_init_smc91x(void)
}
/* Check EMIFS wait states to fix errors with SMC_GET_PKT_HDR */
EMIFS_CCS(1) |= 0x2;
EMIFS_CCS(1) |= 0x3;
}
static void __init osk_init_cf(void)
......@@ -193,8 +191,19 @@ static struct omap_usb_config osk_usb_config __initdata = {
.pins[0] = 2,
};
static struct omap_uart_config osk_uart_config __initdata = {
.enabled_uarts = (1 << 0),
};
static struct omap_lcd_config osk_lcd_config __initdata = {
.panel_name = "osk",
.ctrl_name = "internal",
};
static struct omap_board_config_kernel osk_config[] = {
{ OMAP_TAG_USB, &osk_usb_config },
{ OMAP_TAG_UART, &osk_uart_config },
{ OMAP_TAG_LCD, &osk_lcd_config },
};
#ifdef CONFIG_OMAP_OSK_MISTRAL
......@@ -254,13 +263,13 @@ static void __init osk_init(void)
omap_board_config_size = ARRAY_SIZE(osk_config);
USB_TRANSCEIVER_CTRL_REG |= (3 << 1);
omap_serial_init();
osk_mistral_init();
}
static void __init osk_map_io(void)
{
omap_map_common_io();
omap_serial_init(osk_serial_ports);
}
MACHINE_START(OMAP_OSK, "TI-OSK")
......
/*
* linux/arch/arm/mach-omap1/board-palmte.c
*
* Modified from board-generic.c
*
* Support for the Palm Tungsten E PDA.
*
* Original version : Laurent Gonzalez
*
* Maintainters : http://palmtelinux.sf.net
* palmtelinux-developpers@lists.sf.net
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/notifier.h>
#include <asm/hardware.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
#include <asm/arch/gpio.h>
#include <asm/arch/mux.h>
#include <asm/arch/usb.h>
#include <asm/arch/board.h>
#include <asm/arch/common.h>
#include <asm/hardware/clock.h>
static void __init omap_generic_init_irq(void)
{
omap_init_irq();
}
static struct omap_usb_config palmte_usb_config __initdata = {
.register_dev = 1,
.hmc_mode = 0,
.pins[0] = 3,
};
static struct omap_mmc_config palmte_mmc_config __initdata = {
.mmc [0] = {
.enabled = 1,
.wire4 = 1,
.wp_pin = OMAP_MPUIO(3),
.power_pin = -1,
.switch_pin = -1,
},
};
static struct omap_lcd_config palmte_lcd_config __initdata = {
.panel_name = "palmte",
.ctrl_name = "internal",
};
static struct omap_board_config_kernel palmte_config[] = {
{ OMAP_TAG_USB, &palmte_usb_config },
{ OMAP_TAG_MMC, &palmte_mmc_config },
{ OMAP_TAG_LCD, &palmte_lcd_config },
};
static void __init omap_generic_init(void)
{
omap_board_config = palmte_config;
omap_board_config_size = ARRAY_SIZE(palmte_config);
}
static void __init omap_generic_map_io(void)
{
omap_map_common_io();
}
MACHINE_START(OMAP_PALMTE, "OMAP310 based Palm Tungsten E")
.phys_ram = 0x10000000,
.phys_io = 0xfff00000,
.io_pg_offst = ((0xfef00000) >> 18) & 0xfffc,
.boot_params = 0x10000100,
.map_io = omap_generic_map_io,
.init_irq = omap_generic_init_irq,
.init_machine = omap_generic_init,
.timer = &omap_timer,
MACHINE_END
......@@ -29,6 +29,7 @@
#include <asm/arch/mux.h>
#include <asm/arch/fpga.h>
#include <asm/arch/common.h>
#include <asm/arch/board.h>
static struct resource smc91x_resources[] = {
[0] = {
......@@ -43,8 +44,6 @@ static struct resource smc91x_resources[] = {
},
};
static int __initdata p2_serial_ports[OMAP_MAX_NR_PORTS] = {1, 1, 0};
static struct mtd_partition p2_partitions[] = {
/* bootloader (U-Boot, etc) in first sector */
{
......@@ -111,9 +110,27 @@ static struct platform_device *devices[] __initdata = {
&smc91x_device,
};
static struct omap_uart_config perseus2_uart_config __initdata = {
.enabled_uarts = ((1 << 0) | (1 << 1)),
};
static struct omap_lcd_config perseus2_lcd_config __initdata = {
.panel_name = "p2",
.ctrl_name = "internal",
};
static struct omap_board_config_kernel perseus2_config[] = {
{ OMAP_TAG_UART, &perseus2_uart_config },
{ OMAP_TAG_LCD, &perseus2_lcd_config },
};
static void __init omap_perseus2_init(void)
{
(void) platform_add_devices(devices, ARRAY_SIZE(devices));
omap_board_config = perseus2_config;
omap_board_config_size = ARRAY_SIZE(perseus2_config);
omap_serial_init();
}
static void __init perseus2_init_smc91x(void)
......@@ -131,7 +148,6 @@ void omap_perseus2_init_irq(void)
omap_gpio_init();
perseus2_init_smc91x();
}
/* Only FPGA needs to be mapped here. All others are done with ioremap */
static struct map_desc omap_perseus2_io_desc[] __initdata = {
{
......@@ -179,7 +195,6 @@ static void __init omap_perseus2_map_io(void)
* It is used as the Ethernet controller interrupt
*/
omap_writel(omap_readl(OMAP730_IO_CONF_9) & 0x1FFFFFFF, OMAP730_IO_CONF_9);
omap_serial_init(p2_serial_ports);
}
MACHINE_START(OMAP_PERSEUS2, "OMAP730 Perseus2")
......
......@@ -150,9 +150,14 @@ static struct omap_mmc_config voiceblue_mmc_config __initdata = {
},
};
static struct omap_uart_config voiceblue_uart_config __initdata = {
.enabled_uarts = ((1 << 0) | (1 << 1) | (1 << 2)),
};
static struct omap_board_config_kernel voiceblue_config[] = {
{ OMAP_TAG_USB, &voiceblue_usb_config },
{ OMAP_TAG_MMC, &voiceblue_mmc_config },
{ OMAP_TAG_UART, &voiceblue_uart_config },
};
static void __init voiceblue_init_irq(void)
......@@ -191,6 +196,7 @@ static void __init voiceblue_init(void)
platform_add_devices(voiceblue_devices, ARRAY_SIZE(voiceblue_devices));
omap_board_config = voiceblue_config;
omap_board_config_size = ARRAY_SIZE(voiceblue_config);
omap_serial_init();
/* There is a good chance board is going up, so enable power LED
* (it is connected through invertor) */
......@@ -198,12 +204,9 @@ static void __init voiceblue_init(void)
omap_writeb(0x00, OMAP_LPG1_PMR); /* Disable clock */
}
static int __initdata omap_serial_ports[OMAP_MAX_NR_PORTS] = {1, 1, 1};
static void __init voiceblue_map_io(void)
{
omap_map_common_io();
omap_serial_init(omap_serial_ports);
}
#define MACHINE_PANICED 1
......
This diff is collapsed.
This diff is collapsed.
......@@ -25,56 +25,7 @@
#include <asm/arch/mux.h>
#include <asm/arch/gpio.h>
static void omap_nop_release(struct device *dev)
{
/* Nothing */
}
/*-------------------------------------------------------------------------*/
#if defined(CONFIG_I2C_OMAP) || defined(CONFIG_I2C_OMAP_MODULE)
#define OMAP_I2C_BASE 0xfffb3800
static struct resource i2c_resources[] = {
{
.start = OMAP_I2C_BASE,
.end = OMAP_I2C_BASE + 0x3f,
.flags = IORESOURCE_MEM,
},
{
.start = INT_I2C,
.flags = IORESOURCE_IRQ,
},
};
/* DMA not used; works around erratum writing to non-empty i2c fifo */
static struct platform_device omap_i2c_device = {
.name = "i2c_omap",
.id = -1,
.dev = {
.release = omap_nop_release,
},
.num_resources = ARRAY_SIZE(i2c_resources),
.resource = i2c_resources,
};
static void omap_init_i2c(void)
{
/* FIXME define and use a boot tag, in case of boards that
* either don't wire up I2C, or chips that mux it differently...
* it can include clocking and address info, maybe more.
*/
omap_cfg_reg(I2C_SCL);
omap_cfg_reg(I2C_SDA);
(void) platform_device_register(&omap_i2c_device);
}
#else
static inline void omap_init_i2c(void) {}
#endif
extern void omap_nop_release(struct device *dev);
/*-------------------------------------------------------------------------*/
......@@ -110,137 +61,6 @@ static inline void omap_init_irda(void) {}
/*-------------------------------------------------------------------------*/
#if defined(CONFIG_MMC_OMAP) || defined(CONFIG_MMC_OMAP_MODULE)
#define OMAP_MMC1_BASE 0xfffb7800
#define OMAP_MMC2_BASE 0xfffb7c00 /* omap16xx only */
static struct omap_mmc_conf mmc1_conf;
static u64 mmc1_dmamask = 0xffffffff;
static struct resource mmc1_resources[] = {
{
.start = IO_ADDRESS(OMAP_MMC1_BASE),
.end = IO_ADDRESS(OMAP_MMC1_BASE) + 0x7f,
.flags = IORESOURCE_MEM,
},
{
.start = INT_MMC,
.flags = IORESOURCE_IRQ,
},
};
static struct platform_device mmc_omap_device1 = {
.name = "mmci-omap",
.id = 1,
.dev = {
.release = omap_nop_release,
.dma_mask = &mmc1_dmamask,
.platform_data = &mmc1_conf,
},
.num_resources = ARRAY_SIZE(mmc1_resources),
.resource = mmc1_resources,
};
#ifdef CONFIG_ARCH_OMAP16XX
static struct omap_mmc_conf mmc2_conf;
static u64 mmc2_dmamask = 0xffffffff;
static struct resource mmc2_resources[] = {
{
.start = IO_ADDRESS(OMAP_MMC2_BASE),
.end = IO_ADDRESS(OMAP_MMC2_BASE) + 0x7f,
.flags = IORESOURCE_MEM,
},
{
.start = INT_1610_MMC2,
.flags = IORESOURCE_IRQ,
},
};
static struct platform_device mmc_omap_device2 = {
.name = "mmci-omap",
.id = 2,
.dev = {
.release = omap_nop_release,
.dma_mask = &mmc2_dmamask,
.platform_data = &mmc2_conf,
},
.num_resources = ARRAY_SIZE(mmc2_resources),
.resource = mmc2_resources,
};
#endif
static void __init omap_init_mmc(void)
{
const struct omap_mmc_config *mmc_conf;
const struct omap_mmc_conf *mmc;
/* NOTE: assumes MMC was never (wrongly) enabled */
mmc_conf = omap_get_config(OMAP_TAG_MMC, struct omap_mmc_config);
if (!mmc_conf)
return;
/* block 1 is always available and has just one pinout option */
mmc = &mmc_conf->mmc[0];
if (mmc->enabled) {
omap_cfg_reg(MMC_CMD);
omap_cfg_reg(MMC_CLK);
omap_cfg_reg(MMC_DAT0);
if (cpu_is_omap1710()) {
omap_cfg_reg(M15_1710_MMC_CLKI);
omap_cfg_reg(P19_1710_MMC_CMDDIR);
omap_cfg_reg(P20_1710_MMC_DATDIR0);
}
if (mmc->wire4) {
omap_cfg_reg(MMC_DAT1);
/* NOTE: DAT2 can be on W10 (here) or M15 */
if (!mmc->nomux)
omap_cfg_reg(MMC_DAT2);
omap_cfg_reg(MMC_DAT3);
}
mmc1_conf = *mmc;
(void) platform_device_register(&mmc_omap_device1);
}
#ifdef CONFIG_ARCH_OMAP16XX
/* block 2 is on newer chips, and has many pinout options */
mmc = &mmc_conf->mmc[1];
if (mmc->enabled) {
if (!mmc->nomux) {
omap_cfg_reg(Y8_1610_MMC2_CMD);
omap_cfg_reg(Y10_1610_MMC2_CLK);
omap_cfg_reg(R18_1610_MMC2_CLKIN);
omap_cfg_reg(W8_1610_MMC2_DAT0);
if (mmc->wire4) {
omap_cfg_reg(V8_1610_MMC2_DAT1);
omap_cfg_reg(W15_1610_MMC2_DAT2);
omap_cfg_reg(R10_1610_MMC2_DAT3);
}
/* These are needed for the level shifter */
omap_cfg_reg(V9_1610_MMC2_CMDDIR);
omap_cfg_reg(V5_1610_MMC2_DATDIR0);
omap_cfg_reg(W19_1610_MMC2_DATDIR1);
}
/* Feedback clock must be set on OMAP-1710 MMC2 */
if (cpu_is_omap1710())
omap_writel(omap_readl(MOD_CONF_CTRL_1) | (1 << 24),
MOD_CONF_CTRL_1);
mmc2_conf = *mmc;
(void) platform_device_register(&mmc_omap_device2);
}
#endif
return;
}
#else
static inline void omap_init_mmc(void) {}
#endif
#if defined(CONFIG_OMAP_RTC) || defined(CONFIG_OMAP_RTC)
#define OMAP_RTC_BASE 0xfffb4800
......@@ -279,38 +99,6 @@ static void omap_init_rtc(void)
static inline void omap_init_rtc(void) {}
#endif
/*-------------------------------------------------------------------------*/
#if defined(CONFIG_OMAP16XX_WATCHDOG) || defined(CONFIG_OMAP16XX_WATCHDOG_MODULE)
#define OMAP_WDT_BASE 0xfffeb000
static struct resource wdt_resources[] = {
{
.start = OMAP_WDT_BASE,
.end = OMAP_WDT_BASE + 0x4f,
.flags = IORESOURCE_MEM,
},
};
static struct platform_device omap_wdt_device = {
.name = "omap1610_wdt",
.id = -1,
.dev = {
.release = omap_nop_release,
},
.num_resources = ARRAY_SIZE(wdt_resources),
.resource = wdt_resources,
};
static void omap_init_wdt(void)
{
(void) platform_device_register(&omap_wdt_device);
}
#else
static inline void omap_init_wdt(void) {}
#endif
/*-------------------------------------------------------------------------*/
......@@ -334,18 +122,15 @@ static inline void omap_init_wdt(void) {}
* may be handled by the boot loader, and drivers should expect it will
* normally have been done by the time they're probed.
*/
static int __init omap_init_devices(void)
static int __init omap1_init_devices(void)
{
/* please keep these calls, and their implementations above,
* in alphabetical order so they're easier to sort through.
*/
omap_init_i2c();
omap_init_irda();
omap_init_mmc();
omap_init_rtc();
omap_init_wdt();
return 0;
}
arch_initcall(omap_init_devices);
arch_initcall(omap1_init_devices);
......@@ -18,6 +18,13 @@
#include <asm/io.h>
#define OMAP_DIE_ID_0 0xfffe1800
#define OMAP_DIE_ID_1 0xfffe1804
#define OMAP_PRODUCTION_ID_0 0xfffe2000
#define OMAP_PRODUCTION_ID_1 0xfffe2004
#define OMAP32_ID_0 0xfffed400
#define OMAP32_ID_1 0xfffed404
struct omap_id {
u16 jtag_id; /* Used to determine OMAP type */
u8 die_rev; /* Processor revision */
......@@ -27,6 +34,7 @@ struct omap_id {
/* Register values to detect the OMAP version */
static struct omap_id omap_ids[] __initdata = {
{ .jtag_id = 0xb574, .die_rev = 0x2, .omap_id = 0x03310315, .type = 0x03100000},
{ .jtag_id = 0x355f, .die_rev = 0x0, .omap_id = 0x03320000, .type = 0x07300100},
{ .jtag_id = 0xb55f, .die_rev = 0x0, .omap_id = 0x03320000, .type = 0x07300300},
{ .jtag_id = 0xb470, .die_rev = 0x0, .omap_id = 0x03310100, .type = 0x15100000},
......@@ -164,6 +172,7 @@ void __init omap_check_revision(void)
case 0x07:
system_rev |= 0x07;
break;
case 0x03:
case 0x15:
system_rev |= 0x15;
break;
......
......@@ -15,9 +15,10 @@
#include <asm/mach/map.h>
#include <asm/io.h>
#include <asm/arch/mux.h>
#include <asm/arch/tc.h>
extern int clk_init(void);
extern int omap1_clk_init(void);
extern void omap_check_revision(void);
extern void omap_sram_init(void);
......@@ -50,7 +51,7 @@ static struct map_desc omap730_io_desc[] __initdata = {
};
#endif
#ifdef CONFIG_ARCH_OMAP1510
#ifdef CONFIG_ARCH_OMAP15XX
static struct map_desc omap1510_io_desc[] __initdata = {
{
.virtual = OMAP1510_DSP_BASE,
......@@ -98,7 +99,7 @@ static void __init _omap_map_io(void)
iotable_init(omap730_io_desc, ARRAY_SIZE(omap730_io_desc));
}
#endif
#ifdef CONFIG_ARCH_OMAP1510
#ifdef CONFIG_ARCH_OMAP15XX
if (cpu_is_omap1510()) {
iotable_init(omap1510_io_desc, ARRAY_SIZE(omap1510_io_desc));
}
......@@ -119,7 +120,7 @@ static void __init _omap_map_io(void)
/* Must init clocks early to assure that timer interrupt works
*/
clk_init();
omap1_clk_init();
}
/*
......@@ -127,7 +128,9 @@ static void __init _omap_map_io(void)
*/
void __init omap_map_common_io(void)
{
if (!initialized)
if (!initialized) {
_omap_map_io();
omap1_mux_init();
}
}
......@@ -47,6 +47,7 @@
#include <asm/irq.h>
#include <asm/mach/irq.h>
#include <asm/arch/gpio.h>
#include <asm/arch/cpu.h>
#include <asm/io.h>
......@@ -147,11 +148,15 @@ static struct omap_irq_bank omap730_irq_banks[] = {
};
#endif
#ifdef CONFIG_ARCH_OMAP1510
#ifdef CONFIG_ARCH_OMAP15XX
static struct omap_irq_bank omap1510_irq_banks[] = {
{ .base_reg = OMAP_IH1_BASE, .trigger_map = 0xb3febfff },
{ .base_reg = OMAP_IH2_BASE, .trigger_map = 0xffbfffed },
};
static struct omap_irq_bank omap310_irq_banks[] = {
{ .base_reg = OMAP_IH1_BASE, .trigger_map = 0xb3faefc3 },
{ .base_reg = OMAP_IH2_BASE, .trigger_map = 0x65b3c061 },
};
#endif
#if defined(CONFIG_ARCH_OMAP16XX)
......@@ -181,11 +186,15 @@ void __init omap_init_irq(void)
irq_bank_count = ARRAY_SIZE(omap730_irq_banks);
}
#endif
#ifdef CONFIG_ARCH_OMAP1510
#ifdef CONFIG_ARCH_OMAP15XX
if (cpu_is_omap1510()) {
irq_banks = omap1510_irq_banks;
irq_bank_count = ARRAY_SIZE(omap1510_irq_banks);
}
if (cpu_is_omap310()) {
irq_banks = omap310_irq_banks;
irq_bank_count = ARRAY_SIZE(omap310_irq_banks);
}
#endif
#if defined(CONFIG_ARCH_OMAP16XX)
if (cpu_is_omap16xx()) {
......@@ -226,9 +235,11 @@ void __init omap_init_irq(void)
}
/* Unmask level 2 handler */
if (cpu_is_omap730()) {
if (cpu_is_omap730())
omap_unmask_irq(INT_730_IH2_IRQ);
} else {
omap_unmask_irq(INT_IH2_IRQ);
}
else if (cpu_is_omap1510())
omap_unmask_irq(INT_1510_IH2_IRQ);
else if (cpu_is_omap16xx())
omap_unmask_irq(INT_1610_IH2_IRQ);
}
......@@ -18,6 +18,7 @@
#include <asm/hardware.h>
#include <asm/leds.h>
#include <asm/system.h>
#include <asm/mach-types.h>
#include <asm/arch/fpga.h>
#include <asm/arch/gpio.h>
......@@ -63,14 +64,19 @@ void h2p2_dbg_leds_event(led_event_t evt)
case led_stop:
case led_halted:
/* all leds off during suspend or shutdown */
omap_set_gpio_dataout(GPIO_TIMER, 0);
omap_set_gpio_dataout(GPIO_IDLE, 0);
if (! machine_is_omap_perseus2()) {
omap_set_gpio_dataout(GPIO_TIMER, 0);
omap_set_gpio_dataout(GPIO_IDLE, 0);
}
__raw_writew(~0, &fpga->leds);
led_state &= ~LED_STATE_ENABLED;
if (evt == led_halted) {
iounmap(fpga);
fpga = NULL;
}
goto done;
case led_claim:
......@@ -85,18 +91,37 @@ void h2p2_dbg_leds_event(led_event_t evt)
#ifdef CONFIG_LEDS_TIMER
case led_timer:
led_state ^= LED_TIMER_ON;
omap_set_gpio_dataout(GPIO_TIMER, led_state & LED_TIMER_ON);
goto done;
if (machine_is_omap_perseus2())
hw_led_state ^= H2P2_DBG_FPGA_P2_LED_TIMER;
else {
omap_set_gpio_dataout(GPIO_TIMER, led_state & LED_TIMER_ON);
goto done;
}
break;
#endif
#ifdef CONFIG_LEDS_CPU
case led_idle_start:
omap_set_gpio_dataout(GPIO_IDLE, 1);
goto done;
if (machine_is_omap_perseus2())
hw_led_state |= H2P2_DBG_FPGA_P2_LED_IDLE;
else {
omap_set_gpio_dataout(GPIO_IDLE, 1);
goto done;
}
break;
case led_idle_end:
omap_set_gpio_dataout(GPIO_IDLE, 0);
goto done;
if (machine_is_omap_perseus2())
hw_led_state &= ~H2P2_DBG_FPGA_P2_LED_IDLE;
else {
omap_set_gpio_dataout(GPIO_IDLE, 0);
goto done;
}
break;
#endif
case led_green_on:
......@@ -135,7 +160,7 @@ void h2p2_dbg_leds_event(led_event_t evt)
/*
* Actually burn the LEDs
*/
if (led_state & LED_STATE_CLAIMED)
if (led_state & LED_STATE_ENABLED)
__raw_writew(~hw_led_state, &fpga->leds);
done:
......
......@@ -33,7 +33,6 @@ omap_leds_init(void)
if (machine_is_omap_h2()
|| machine_is_omap_h3()
|| machine_is_omap_perseus2()
#ifdef CONFIG_OMAP_OSK_MISTRAL
|| machine_is_omap_osk()
#endif
......
This diff is collapsed.
......@@ -109,9 +109,10 @@ static struct platform_device serial_device = {
* By default UART2 does not work on Innovator-1510 if you have
* USB OHCI enabled. To use UART2, you must disable USB2 first.
*/
void __init omap_serial_init(int ports[OMAP_MAX_NR_PORTS])
void __init omap_serial_init(void)
{
int i;
const struct omap_uart_config *info;
if (cpu_is_omap730()) {
serial_platform_data[0].regshift = 0;
......@@ -126,10 +127,14 @@ void __init omap_serial_init(int ports[OMAP_MAX_NR_PORTS])
serial_platform_data[2].uartclk = OMAP1510_BASE_BAUD * 16;
}
info = omap_get_config(OMAP_TAG_UART, struct omap_uart_config);
if (info == NULL)
return;
for (i = 0; i < OMAP_MAX_NR_PORTS; i++) {
unsigned char reg;
if (ports[i] == 0) {
if (!((1 << i) & info->enabled_uarts)) {
serial_platform_data[i].membase = NULL;
serial_platform_data[i].mapbase = 0;
continue;
......
......@@ -226,8 +226,8 @@ unsigned long long sched_clock(void)
#ifdef CONFIG_OMAP_32K_TIMER
#ifdef CONFIG_ARCH_OMAP1510
#error OMAP 32KHz timer does not currently work on 1510!
#ifdef CONFIG_ARCH_OMAP15XX
#error OMAP 32KHz timer does not currently work on 15XX!
#endif
/*
......
comment "OMAP Core Type"
depends on ARCH_OMAP2
config ARCH_OMAP24XX
bool "OMAP24xx Based System"
depends on ARCH_OMAP2
config ARCH_OMAP2420
bool "OMAP2420 support"
depends on ARCH_OMAP24XX
comment "OMAP Board Type"
depends on ARCH_OMAP2
config MACH_OMAP_GENERIC
bool "Generic OMAP board"
depends on ARCH_OMAP2 && ARCH_OMAP24XX
config MACH_OMAP_H4
bool "OMAP 2420 H4 board"
depends on ARCH_OMAP2 && ARCH_OMAP24XX
#
# Makefile for the linux kernel.
#
# Common support
obj-y := irq.o id.o io.o sram-fn.o clock.o mux.o devices.o serial.o
obj-$(CONFIG_OMAP_MPU_TIMER) += timer-gp.o
# Specific board support
obj-$(CONFIG_MACH_OMAP_GENERIC) += board-generic.o
obj-$(CONFIG_MACH_OMAP_H4) += board-h4.o
zreladdr-y := 0x80008000
params_phys-y := 0x80000100
initrd_phys-y := 0x80800000
/*
* linux/arch/arm/mach-omap/omap2/board-generic.c
*
* Copyright (C) 2005 Nokia Corporation
* Author: Paul Mundt <paul.mundt@nokia.com>
*
* Modified from mach-omap/omap1/board-generic.c
*
* Code for generic OMAP2 board. Should work on many OMAP2 systems where
* the bootloader passes the board-specific data to the kernel.
* Do not put any board specific code to this file; create a new machine
* type if you need custom low-level initializations.
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/device.h>
#include <asm/hardware.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
#include <asm/arch/gpio.h>
#include <asm/arch/mux.h>
#include <asm/arch/usb.h>
#include <asm/arch/board.h>
#include <asm/arch/common.h>
static void __init omap_generic_init_irq(void)
{
omap_init_irq();
}
static struct omap_uart_config generic_uart_config __initdata = {
.enabled_uarts = ((1 << 0) | (1 << 1) | (1 << 2)),
};
static struct omap_mmc_config generic_mmc_config __initdata = {
.mmc [0] = {
.enabled = 0,
.wire4 = 0,
.wp_pin = -1,
.power_pin = -1,
.switch_pin = -1,
},
};
static struct omap_board_config_kernel generic_config[] = {
{ OMAP_TAG_UART, &generic_uart_config },
{ OMAP_TAG_MMC, &generic_mmc_config },
};
static void __init omap_generic_init(void)
{
omap_board_config = generic_config;
omap_board_config_size = ARRAY_SIZE(generic_config);
omap_serial_init();
}
static void __init omap_generic_map_io(void)
{
omap_map_common_io();
}
MACHINE_START(OMAP_GENERIC, "Generic OMAP24xx")
/* Maintainer: Paul Mundt <paul.mundt@nokia.com> */
.phys_ram = 0x80000000,
.phys_io = 0x48000000,
.io_pg_offst = ((0xd8000000) >> 18) & 0xfffc,
.boot_params = 0x80000100,
.map_io = omap_generic_map_io,
.init_irq = omap_generic_init_irq,
.init_machine = omap_generic_init,
.timer = &omap_timer,
MACHINE_END
/*
* linux/arch/arm/mach-omap/omap2/board-h4.c
*
* Copyright (C) 2005 Nokia Corporation
* Author: Paul Mundt <paul.mundt@nokia.com>
*
* Modified from mach-omap/omap1/board-generic.c
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/mtd/mtd.h>
#include <linux/mtd/partitions.h>
#include <linux/delay.h>
#include <asm/hardware.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
#include <asm/mach/flash.h>
#include <asm/arch/gpio.h>
#include <asm/arch/mux.h>
#include <asm/arch/usb.h>
#include <asm/arch/board.h>
#include <asm/arch/common.h>
#include <asm/arch/prcm.h>
#include <asm/io.h>
#include <asm/delay.h>
static struct mtd_partition h4_partitions[] = {
/* bootloader (U-Boot, etc) in first sector */
{
.name = "bootloader",
.offset = 0,
.size = SZ_128K,
.mask_flags = MTD_WRITEABLE, /* force read-only */
},
/* bootloader params in the next sector */
{
.name = "params",
.offset = MTDPART_OFS_APPEND,
.size = SZ_128K,
.mask_flags = 0,
},
/* kernel */
{
.name = "kernel",
.offset = MTDPART_OFS_APPEND,
.size = SZ_2M,
.mask_flags = 0
},
/* file system */
{
.name = "filesystem",
.offset = MTDPART_OFS_APPEND,
.size = MTDPART_SIZ_FULL,
.mask_flags = 0
}
};
static struct flash_platform_data h4_flash_data = {
.map_name = "cfi_probe",
.width = 2,
.parts = h4_partitions,
.nr_parts = ARRAY_SIZE(h4_partitions),
};
static struct resource h4_flash_resource = {
.start = H4_CS0_BASE,
.end = H4_CS0_BASE + SZ_64M - 1,
.flags = IORESOURCE_MEM,
};
static struct platform_device h4_flash_device = {
.name = "omapflash",
.id = 0,
.dev = {
.platform_data = &h4_flash_data,
},
.num_resources = 1,
.resource = &h4_flash_resource,
};
static struct resource h4_smc91x_resources[] = {
[0] = {
.start = OMAP24XX_ETHR_START, /* Physical */
.end = OMAP24XX_ETHR_START + 0xf,
.flags = IORESOURCE_MEM,
},
[1] = {
.start = OMAP_GPIO_IRQ(OMAP24XX_ETHR_GPIO_IRQ),
.end = OMAP_GPIO_IRQ(OMAP24XX_ETHR_GPIO_IRQ),
.flags = IORESOURCE_IRQ,
},
};
static struct platform_device h4_smc91x_device = {
.name = "smc91x",
.id = -1,
.num_resources = ARRAY_SIZE(h4_smc91x_resources),
.resource = h4_smc91x_resources,
};
static struct platform_device *h4_devices[] __initdata = {
&h4_smc91x_device,
&h4_flash_device,
};
static inline void __init h4_init_smc91x(void)
{
/* Make sure CS1 timings are correct */
GPMC_CONFIG1_1 = 0x00011200;
GPMC_CONFIG2_1 = 0x001f1f01;
GPMC_CONFIG3_1 = 0x00080803;
GPMC_CONFIG4_1 = 0x1c091c09;
GPMC_CONFIG5_1 = 0x041f1f1f;
GPMC_CONFIG6_1 = 0x000004c4;
GPMC_CONFIG7_1 = 0x00000f40 | (0x08000000 >> 24);
udelay(100);
omap_cfg_reg(M15_24XX_GPIO92);
if (omap_request_gpio(OMAP24XX_ETHR_GPIO_IRQ) < 0) {
printk(KERN_ERR "Failed to request GPIO%d for smc91x IRQ\n",
OMAP24XX_ETHR_GPIO_IRQ);
return;
}
omap_set_gpio_direction(OMAP24XX_ETHR_GPIO_IRQ, 1);
}
static void __init omap_h4_init_irq(void)
{
omap_init_irq();
omap_gpio_init();
h4_init_smc91x();
}
static struct omap_uart_config h4_uart_config __initdata = {
.enabled_uarts = ((1 << 0) | (1 << 1) | (1 << 2)),
};
static struct omap_mmc_config h4_mmc_config __initdata = {
.mmc [0] = {
.enabled = 1,
.wire4 = 1,
.wp_pin = -1,
.power_pin = -1,
.switch_pin = -1,
},
};
static struct omap_lcd_config h4_lcd_config __initdata = {
.panel_name = "h4",
.ctrl_name = "internal",
};
static struct omap_board_config_kernel h4_config[] = {
{ OMAP_TAG_UART, &h4_uart_config },
{ OMAP_TAG_MMC, &h4_mmc_config },
{ OMAP_TAG_LCD, &h4_lcd_config },
};
static void __init omap_h4_init(void)
{
/*
* Make sure the serial ports are muxed on at this point.
* You have to mux them off in device drivers later on
* if not needed.
*/
platform_add_devices(h4_devices, ARRAY_SIZE(h4_devices));
omap_board_config = h4_config;
omap_board_config_size = ARRAY_SIZE(h4_config);
omap_serial_init();
}
static void __init omap_h4_map_io(void)
{
omap_map_common_io();
}
MACHINE_START(OMAP_H4, "OMAP2420 H4 board")
/* Maintainer: Paul Mundt <paul.mundt@nokia.com> */
.phys_ram = 0x80000000,
.phys_io = 0x48000000,
.io_pg_offst = ((0xd8000000) >> 18) & 0xfffc,
.boot_params = 0x80000100,
.map_io = omap_h4_map_io,
.init_irq = omap_h4_init_irq,
.init_machine = omap_h4_init,
.timer = &omap_timer,
MACHINE_END
This diff is collapsed.
This diff is collapsed.
/*
* linux/arch/arm/mach-omap2/devices.c
*
* OMAP2 platform device setup/initialization
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*/
#include <linux/config.h>
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <asm/hardware.h>
#include <asm/io.h>
#include <asm/mach-types.h>
#include <asm/mach/map.h>
#include <asm/arch/tc.h>
#include <asm/arch/board.h>
#include <asm/arch/mux.h>
#include <asm/arch/gpio.h>
extern void omap_nop_release(struct device *dev);
/*-------------------------------------------------------------------------*/
#if defined(CONFIG_I2C_OMAP) || defined(CONFIG_I2C_OMAP_MODULE)
#define OMAP2_I2C_BASE2 0x48072000
#define OMAP2_I2C_INT2 57
static struct resource i2c_resources2[] = {
{
.start = OMAP2_I2C_BASE2,
.end = OMAP2_I2C_BASE2 + 0x3f,
.flags = IORESOURCE_MEM,
},
{
.start = OMAP2_I2C_INT2,
.flags = IORESOURCE_IRQ,
},
};
static struct platform_device omap_i2c_device2 = {
.name = "i2c_omap",
.id = 2,
.dev = {
.release = omap_nop_release,
},
.num_resources = ARRAY_SIZE(i2c_resources2),
.resource = i2c_resources2,
};
/* See also arch/arm/plat-omap/devices.c for first I2C on 24xx */
static void omap_init_i2c(void)
{
/* REVISIT: Second I2C not in use on H4? */
if (machine_is_omap_h4())
return;
omap_cfg_reg(J15_24XX_I2C2_SCL);
omap_cfg_reg(H19_24XX_I2C2_SDA);
(void) platform_device_register(&omap_i2c_device2);
}
#else
static void omap_init_i2c(void) {}
#endif
/*-------------------------------------------------------------------------*/
static int __init omap2_init_devices(void)
{
/* please keep these calls, and their implementations above,
* in alphabetical order so they're easier to sort through.
*/
omap_init_i2c();
return 0;
}
arch_initcall(omap2_init_devices);
/*
* linux/arch/arm/mach-omap2/id.c
*
* OMAP2 CPU identification code
*
* Copyright (C) 2005 Nokia Corporation
* Written by Tony Lindgren <tony@atomide.com>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
#include <linux/config.h>
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <asm/io.h>
#define OMAP24XX_TAP_BASE io_p2v(0x48014000)
#define OMAP_TAP_IDCODE 0x0204
#define OMAP_TAP_PROD_ID 0x0208
#define OMAP_TAP_DIE_ID_0 0x0218
#define OMAP_TAP_DIE_ID_1 0x021C
#define OMAP_TAP_DIE_ID_2 0x0220
#define OMAP_TAP_DIE_ID_3 0x0224
/* system_rev fields for OMAP2 processors:
* CPU id bits [31:16],
* CPU device type [15:12], (unprg,normal,POP)
* CPU revision [11:08]
* CPU class bits [07:00]
*/
struct omap_id {
u16 hawkeye; /* Silicon type (Hawkeye id) */
u8 dev; /* Device type from production_id reg */
u32 type; /* combined type id copied to system_rev */
};
/* Register values to detect the OMAP version */
static struct omap_id omap_ids[] __initdata = {
{ .hawkeye = 0xb5d9, .dev = 0x0, .type = 0x24200000 },
{ .hawkeye = 0xb5d9, .dev = 0x1, .type = 0x24201000 },
{ .hawkeye = 0xb5d9, .dev = 0x2, .type = 0x24202000 },
{ .hawkeye = 0xb5d9, .dev = 0x4, .type = 0x24220000 },
{ .hawkeye = 0xb5d9, .dev = 0x8, .type = 0x24230000 },
{ .hawkeye = 0xb68a, .dev = 0x0, .type = 0x24300000 },
};
static u32 __init read_tap_reg(int reg)
{
return __raw_readl(OMAP24XX_TAP_BASE + reg);
}
void __init omap2_check_revision(void)
{
int i, j;
u32 idcode;
u32 prod_id;
u16 hawkeye;
u8 dev_type;
u8 rev;
idcode = read_tap_reg(OMAP_TAP_IDCODE);
prod_id = read_tap_reg(OMAP_TAP_PROD_ID);
hawkeye = (idcode >> 12) & 0xffff;
rev = (idcode >> 28) & 0x0f;
dev_type = (prod_id >> 16) & 0x0f;
#ifdef DEBUG
printk(KERN_DEBUG "OMAP_TAP_IDCODE 0x%08x REV %i HAWKEYE 0x%04x MANF %03x\n",
idcode, rev, hawkeye, (idcode >> 1) & 0x7ff);
printk(KERN_DEBUG "OMAP_TAP_DIE_ID_0: 0x%08x\n",
read_tap_reg(OMAP_TAP_DIE_ID_0));
printk(KERN_DEBUG "OMAP_TAP_DIE_ID_1: 0x%08x DEV_REV: %i\n",
read_tap_reg(OMAP_TAP_DIE_ID_1),
(read_tap_reg(OMAP_TAP_DIE_ID_1) >> 28) & 0xf);
printk(KERN_DEBUG "OMAP_TAP_DIE_ID_2: 0x%08x\n",
read_tap_reg(OMAP_TAP_DIE_ID_2));
printk(KERN_DEBUG "OMAP_TAP_DIE_ID_3: 0x%08x\n",
read_tap_reg(OMAP_TAP_DIE_ID_3));
printk(KERN_DEBUG "OMAP_TAP_PROD_ID_0: 0x%08x DEV_TYPE: %i\n",
prod_id, dev_type);
#endif
/* Check hawkeye ids */
for (i = 0; i < ARRAY_SIZE(omap_ids); i++) {
if (hawkeye == omap_ids[i].hawkeye)
break;
}
if (i == ARRAY_SIZE(omap_ids)) {
printk(KERN_ERR "Unknown OMAP CPU id\n");
return;
}
for (j = i; j < ARRAY_SIZE(omap_ids); j++) {
if (dev_type == omap_ids[j].dev)
break;
}
if (j == ARRAY_SIZE(omap_ids)) {
printk(KERN_ERR "Unknown OMAP device type. "
"Handling it as OMAP%04x\n",
omap_ids[i].type >> 16);
j = i;
}
system_rev = omap_ids[j].type;
system_rev |= rev << 8;
/* Add the cpu class info (24xx) */
system_rev |= 0x24;
pr_info("OMAP%04x", system_rev >> 16);
if ((system_rev >> 8) & 0x0f)
printk("%x", (system_rev >> 8) & 0x0f);
printk("\n");
}
/*
* linux/arch/arm/mach-omap2/io.c
*
* OMAP2 I/O mapping code
*
* Copyright (C) 2005 Nokia Corporation
* Author: Juha Yrjl <juha.yrjola@nokia.com>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
#include <linux/config.h>
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <asm/mach/map.h>
#include <asm/io.h>
#include <asm/arch/mux.h>
extern void omap_sram_init(void);
extern int omap2_clk_init(void);
extern void omap2_check_revision(void);
/*
* The machine specific code may provide the extra mapping besides the
* default mapping provided here.
*/
static struct map_desc omap2_io_desc[] __initdata = {
{
.virtual = L3_24XX_VIRT,
.pfn = __phys_to_pfn(L3_24XX_PHYS),
.length = L3_24XX_SIZE,
.type = MT_DEVICE
},
{
.virtual = L4_24XX_VIRT,
.pfn = __phys_to_pfn(L4_24XX_PHYS),
.length = L4_24XX_SIZE,
.type = MT_DEVICE
}
};
void __init omap_map_common_io(void)
{
iotable_init(omap2_io_desc, ARRAY_SIZE(omap2_io_desc));
omap2_check_revision();
omap_sram_init();
omap2_mux_init();
omap2_clk_init();
}
/*
* linux/arch/arm/mach-omap/omap2/irq.c
*
* Interrupt handler for OMAP2 boards.
*
* Copyright (C) 2005 Nokia Corporation
* Author: Paul Mundt <paul.mundt@nokia.com>
*
* This file is subject to the terms and conditions of the GNU General Public
* License. See the file "COPYING" in the main directory of this archive
* for more details.
*/
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/config.h>
#include <linux/interrupt.h>
#include <asm/hardware.h>
#include <asm/mach/irq.h>
#include <asm/irq.h>
#include <asm/io.h>
#define INTC_REVISION 0x0000
#define INTC_SYSCONFIG 0x0010
#define INTC_SYSSTATUS 0x0014
#define INTC_CONTROL 0x0048
#define INTC_MIR_CLEAR0 0x0088
#define INTC_MIR_SET0 0x008c
/*
* OMAP2 has a number of different interrupt controllers, each interrupt
* controller is identified as its own "bank". Register definitions are
* fairly consistent for each bank, but not all registers are implemented
* for each bank.. when in doubt, consult the TRM.
*/
static struct omap_irq_bank {
unsigned long base_reg;
unsigned int nr_irqs;
} __attribute__ ((aligned(4))) irq_banks[] = {
{
/* MPU INTC */
.base_reg = OMAP24XX_IC_BASE,
.nr_irqs = 96,
}, {
/* XXX: DSP INTC */
#if 0
/*
* Commented out for now until we fix the IVA clocking
*/
#ifdef CONFIG_ARCH_OMAP2420
}, {
/* IVA INTC (2420 only) */
.base_reg = OMAP24XX_IVA_INTC_BASE,
.nr_irqs = 16, /* Actually 32, but only 16 are used */
#endif
#endif
}
};
/* XXX: FIQ and additional INTC support (only MPU at the moment) */
static void omap_ack_irq(unsigned int irq)
{
omap_writel(0x1, irq_banks[0].base_reg + INTC_CONTROL);
}
static void omap_mask_irq(unsigned int irq)
{
int offset = (irq >> 5) << 5;
if (irq >= 64) {
irq %= 64;
} else if (irq >= 32) {
irq %= 32;
}
omap_writel(1 << irq, irq_banks[0].base_reg + INTC_MIR_SET0 + offset);
}
static void omap_unmask_irq(unsigned int irq)
{
int offset = (irq >> 5) << 5;
if (irq >= 64) {
irq %= 64;
} else if (irq >= 32) {
irq %= 32;
}
omap_writel(1 << irq, irq_banks[0].base_reg + INTC_MIR_CLEAR0 + offset);
}
static void omap_mask_ack_irq(unsigned int irq)
{
omap_mask_irq(irq);
omap_ack_irq(irq);
}
static struct irqchip omap_irq_chip = {
.ack = omap_mask_ack_irq,
.mask = omap_mask_irq,
.unmask = omap_unmask_irq,
};
static void __init omap_irq_bank_init_one(struct omap_irq_bank *bank)
{
unsigned long tmp;
tmp = omap_readl(bank->base_reg + INTC_REVISION) & 0xff;
printk(KERN_INFO "IRQ: Found an INTC at 0x%08lx "
"(revision %ld.%ld) with %d interrupts\n",
bank->base_reg, tmp >> 4, tmp & 0xf, bank->nr_irqs);
tmp = omap_readl(bank->base_reg + INTC_SYSCONFIG);
tmp |= 1 << 1; /* soft reset */
omap_writel(tmp, bank->base_reg + INTC_SYSCONFIG);
while (!(omap_readl(bank->base_reg + INTC_SYSSTATUS) & 0x1))
/* Wait for reset to complete */;
}
void __init omap_init_irq(void)
{
unsigned long nr_irqs = 0;
unsigned int nr_banks = 0;
int i;
for (i = 0; i < ARRAY_SIZE(irq_banks); i++) {
struct omap_irq_bank *bank = irq_banks + i;
/* XXX */
if (!bank->base_reg)
continue;
omap_irq_bank_init_one(bank);
nr_irqs += bank->nr_irqs;
nr_banks++;
}
printk(KERN_INFO "Total of %ld interrupts on %d active controller%s\n",
nr_irqs, nr_banks, nr_banks > 1 ? "s" : "");
for (i = 0; i < nr_irqs; i++) {
set_irq_chip(i, &omap_irq_chip);
set_irq_handler(i, do_level_IRQ);
set_irq_flags(i, IRQF_VALID);
}
}
/*
* linux/arch/arm/mach-omap2/mux.c
*
* OMAP1 pin multiplexing configurations
*
* Copyright (C) 2003 - 2005 Nokia Corporation
*
* Written by Tony Lindgren <tony.lindgren@nokia.com>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
*
*/
#include <linux/config.h>
#include <linux/module.h>
#include <linux/init.h>
#include <asm/system.h>
#include <asm/io.h>
#include <linux/spinlock.h>
#include <asm/arch/mux.h>
#ifdef CONFIG_OMAP_MUX
/* NOTE: See mux.h for the enumeration */
struct pin_config __initdata_or_module omap24xx_pins[] = {
/*
* description mux mux pull pull debug
* offset mode ena type
*/
/* 24xx I2C */
MUX_CFG_24XX("M19_24XX_I2C1_SCL", 0x111, 0, 0, 0, 1)
MUX_CFG_24XX("L15_24XX_I2C1_SDA", 0x112, 0, 0, 0, 1)
MUX_CFG_24XX("J15_24XX_I2C2_SCL", 0x113, 0, 0, 0, 1)
MUX_CFG_24XX("H19_24XX_I2C2_SDA", 0x114, 0, 0, 0, 1)
/* Menelaus interrupt */
MUX_CFG_24XX("W19_24XX_SYS_NIRQ", 0x12c, 0, 1, 1, 1)
/* 24xx GPIO */
MUX_CFG_24XX("Y20_24XX_GPIO60", 0x12c, 3, 0, 0, 1)
MUX_CFG_24XX("M15_24XX_GPIO92", 0x10a, 3, 0, 0, 1)
};
int __init omap2_mux_init(void)
{
omap_mux_register(omap24xx_pins, ARRAY_SIZE(omap24xx_pins));
return 0;
}
#endif
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
......@@ -60,6 +60,7 @@ config MACH_CORGI
bool "Enable Sharp SL-C700 (Corgi) Support"
depends PXA_SHARPSL_25x
select PXA_SHARP_C7xx
select PXA_SSP
config MACH_SHEPHERD
bool "Enable Sharp SL-C750 (Shepherd) Support"
......@@ -102,12 +103,18 @@ config IWMMXT
config PXA_SHARP_C7xx
bool
select PXA_SSP
help
Enable support for all Sharp C7xx models
config PXA_SHARP_Cxx00
bool
select PXA_SSP
help
Enable common support for Sharp Cxx00 models
config PXA_SSP
tristate
help
Enable support for PXA2xx SSP ports
endif
This diff is collapsed.
......@@ -203,7 +203,7 @@ static int __init corgi_ssp_probe(struct device *dev)
GPDR(ssp_machinfo->cs_ads7846) |= GPIO_bit(ssp_machinfo->cs_ads7846); /* output */
GPSR(ssp_machinfo->cs_ads7846) = GPIO_bit(ssp_machinfo->cs_ads7846); /* High - Disable ADS7846*/
ret = ssp_init(&corgi_ssp_dev,ssp_machinfo->port);
ret = ssp_init(&corgi_ssp_dev, ssp_machinfo->port, 0);
if (ret)
printk(KERN_ERR "Unable to register SSP handler!\n");
......
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment