Commit 958bb025 authored by Srinivas Kandagatla's avatar Srinivas Kandagatla Committed by Linus Walleij

dt-bindings: pinctrl: qcom: Add sc8280xp lpass lpi pinctrl bindings

Add device tree binding Documentation details for Qualcomm SC8280XP
LPASS(Low Power Audio Sub System) LPI(Low Power Island) pinctrl driver.
Signed-off-by: default avatarSrinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: default avatarRob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20220817113747.9111-2-srinivas.kandagatla@linaro.orgSigned-off-by: default avatarLinus Walleij <linus.walleij@linaro.org>
parent ec1652fc
# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
%YAML 1.2
---
$id: http://devicetree.org/schemas/pinctrl/qcom,sc8280xp-lpass-lpi-pinctrl.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#
title: Qualcomm Technologies, Inc. Low Power Audio SubSystem (LPASS)
Low Power Island (LPI) TLMM block
maintainers:
- Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
description: |
This binding describes the Top Level Mode Multiplexer block found in the
LPASS LPI IP on most Qualcomm SoCs
properties:
compatible:
const: qcom,sc8280xp-lpass-lpi-pinctrl
reg:
items:
- description: LPASS LPI TLMM Control and Status registers
- description: LPASS LPI pins SLEW registers
clocks:
items:
- description: LPASS Core voting clock
- description: LPASS Audio voting clock
clock-names:
items:
- const: core
- const: audio
gpio-controller: true
'#gpio-cells':
description: Specifying the pin number and flags, as defined in
include/dt-bindings/gpio/gpio.h
const: 2
gpio-ranges:
maxItems: 1
#PIN CONFIGURATION NODES
patternProperties:
'-pins$':
type: object
description:
Pinctrl node's client devices use subnodes for desired pin configuration.
Client device subnodes use below standard properties.
$ref: /schemas/pinctrl/pincfg-node.yaml
properties:
pins:
description:
List of gpio pins affected by the properties specified in this
subnode.
items:
pattern: "^gpio([0-1]|1[0-8]])$"
function:
enum: [ swr_tx_clk, swr_tx_data, swr_rx_clk, swr_rx_data,
dmic1_clk, dmic1_data, dmic2_clk, dmic2_data, dmic4_clk,
dmic4_data, i2s2_clk, i2s2_ws, dmic3_clk, dmic3_data,
qua_mi2s_sclk, qua_mi2s_ws, qua_mi2s_data, i2s1_clk, i2s1_ws,
i2s1_data, wsa_swr_clk, wsa_swr_data, wsa2_swr_clk,
wsa2_swr_data, i2s2_data, i2s3_clk, i2s3_ws, i2s3_data,
ext_mclk1_c, ext_mclk1_b, ext_mclk1_a ]
description:
Specify the alternative function to be configured for the specified
pins.
drive-strength:
enum: [2, 4, 6, 8, 10, 12, 14, 16]
default: 2
description:
Selects the drive strength for the specified pins, in mA.
slew-rate:
enum: [0, 1, 2, 3]
default: 0
description: |
0: No adjustments
1: Higher Slew rate (faster edges)
2: Lower Slew rate (slower edges)
3: Reserved (No adjustments)
bias-pull-down: true
bias-pull-up: true
bias-disable: true
output-high: true
output-low: true
required:
- pins
- function
additionalProperties: false
allOf:
- $ref: pinctrl.yaml#
required:
- compatible
- reg
- clocks
- clock-names
- gpio-controller
- '#gpio-cells'
- gpio-ranges
additionalProperties: false
examples:
- |
#include <dt-bindings/sound/qcom,q6afe.h>
pinctrl@33c0000 {
compatible = "qcom,sc8280xp-lpass-lpi-pinctrl";
reg = <0x33c0000 0x20000>,
<0x3550000 0x10000>;
clocks = <&q6afecc LPASS_HW_MACRO_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
<&q6afecc LPASS_HW_DCODEC_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>;
clock-names = "core", "audio";
gpio-controller;
#gpio-cells = <2>;
gpio-ranges = <&lpi_tlmm 0 0 18>;
};
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment