powerpc/p3060qds: Add support for P3060QDS board

The P3060QDS is a Freescale reference board that hosts the six-core P3060 SOC.
The P3060 Processor combines six e500mc Power Architecture processor cores with
high-performance datapath acceleration architecture(DPAA), CoreNet fabric
infrastructure, as well as network and peripheral interfaces.

P3060QDS Board Overview:
Memory subsystem:
  - 2G Bytes unbuffered DDR3 SDRAM SO-DIMM(64bit bus)
  - 128M Bytes NOR flash single-chip memory
  - 16M Bytes SPI flash
  - 8K Bytes AT24C64 I2C EEPROM
Ethernet:
  - 4x1G + 4x1G/2.5G Ethernet controllers
  - 2xRGMII + 1xMII, three VSC8641 PHYs on board
  - Suport multiple Vitesse VSC8234 SGMII Cards in Slot1/2/3
PCIe: Two PCI Express 2.0 controllers/ports
USB:  Two USB2.0, USB1(TYPE-A) and USB2(TYPE-AB) on board
I2C:  Four I2C controllers
UART: Supports up to four UARTs
RapidIO: Supports two serial RapidIO ports
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

arch/powerpc/boot/dts/p3060qds.dts

+/*
+ * P3060QDS Device Tree Source
+ *
+ * Copyright 2011 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ *     * Redistributions of source code must retain the above copyright
+ *       notice, this list of conditions and the following disclaimer.
+ *     * Redistributions in binary form must reproduce the above copyright
+ *       notice, this list of conditions and the following disclaimer in the
+ *       documentation and/or other materials provided with the distribution.
+ *     * Neither the name of Freescale Semiconductor nor the
+ *       names of its contributors may be used to endorse or promote products
+ *       derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/include/ "p3060si.dtsi"
+
+/ {
+	model = "fsl,P3060QDS";
+	compatible = "fsl,P3060QDS";
+	#address-cells = <2>;
+	#size-cells = <2>;
+	interrupt-parent = <&mpic>;
+
+	memory {
+		device_type = "memory";
+	};
+
+	dcsr: dcsr@f00000000 {
+		ranges = <0x00000000 0xf 0x00000000 0x01008000>;
+	};
+
+	soc: soc@ffe000000 {
+		spi@110000 {
+			flash@0 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				compatible = "spansion,s25sl12801";
+				reg = <0>;
+				spi-max-frequency = <40000000>; /* input clock */
+				partition@u-boot {
+					label = "u-boot";
+					reg = <0x00000000 0x00100000>;
+					read-only;
+				};
+				partition@kernel {
+					label = "kernel";
+					reg = <0x00100000 0x00500000>;
+					read-only;
+				};
+				partition@dtb {
+					label = "dtb";
+					reg = <0x00600000 0x00100000>;
+					read-only;
+				};
+				partition@fs {
+					label = "file system";
+					reg = <0x00700000 0x00900000>;
+				};
+			};
+			flash@1 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				compatible = "spansion,en25q32b";
+				reg = <1>;
+				spi-max-frequency = <40000000>; /* input clock */
+				partition@spi1 {
+					label = "spi1";
+					reg = <0x00000000 0x00400000>;
+				};
+			};
+			flash@2 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				compatible = "atmel,at45db081d";
+				reg = <2>;
+				spi-max-frequency = <40000000>; /* input clock */
+				partition@spi1 {
+					label = "spi2";
+					reg = <0x00000000 0x00100000>;
+				};
+			};
+			flash@3 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				compatible = "spansion,sst25wf040";
+				reg = <3>;
+				spi-max-frequency = <40000000>; /* input clock */
+				partition@spi3 {
+					label = "spi3";
+					reg = <0x00000000 0x00080000>;
+				};
+			};
+		};
+
+		i2c@118000 {
+			eeprom@51 {
+				compatible = "at24,24c256";
+				reg = <0x51>;
+			};
+			eeprom@53 {
+				compatible = "at24,24c256";
+				reg = <0x53>;
+			};
+			rtc@68 {
+				compatible = "dallas,ds3232";
+				reg = <0x68>;
+				interrupts = <0x1 0x1 0 0>;
+			};
+		};
+
+		usb0: usb@210000 {
+			phy_type = "ulpi";
+		};
+
+		usb1: usb@211000 {
+			dr_mode = "host";
+			phy_type = "ulpi";
+		};
+	};
+
+	rapidio@ffe0c0000 {
+		reg = <0xf 0xfe0c0000 0 0x11000>;
+
+		port1 {
+			ranges = <0 0 0xc 0x20000000 0 0x10000000>;
+		};
+		port2 {
+			ranges = <0 0 0xc 0x30000000 0 0x10000000>;
+		};
+	};
+
+	localbus@ffe124000 {
+		reg = <0xf 0xfe124000 0 0x1000>;
+		ranges = <0 0 0xf 0xe8000000 0x08000000
+			  2 0 0xf 0xffa00000 0x00040000
+			  3 0 0xf 0xffdf0000 0x00008000>;
+
+		flash@0,0 {
+			compatible = "cfi-flash";
+			reg = <0 0 0x08000000>;
+			bank-width = <2>;
+			device-width = <2>;
+		};
+
+		nand@2,0 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			compatible = "fsl,elbc-fcm-nand";
+			reg = <0x2 0x0 0x40000>;
+
+			partition@0 {
+				label = "NAND U-Boot Image";
+				reg = <0x0 0x02000000>;
+				read-only;
+			};
+
+			partition@2000000 {
+				label = "NAND Root File System";
+				reg = <0x02000000 0x10000000>;
+			};
+
+			partition@12000000 {
+				label = "NAND Compressed RFS Image";
+				reg = <0x12000000 0x08000000>;
+			};
+
+			partition@1a000000 {
+				label = "NAND Linux Kernel Image";
+				reg = <0x1a000000 0x04000000>;
+			};
+
+			partition@1e000000 {
+				label = "NAND DTB Image";
+				reg = <0x1e000000 0x01000000>;
+			};
+
+			partition@1f000000 {
+				label = "NAND Writable User area";
+				reg = <0x1f000000 0x21000000>;
+			};
+		};
+
+		board-control@3,0 {
+			compatible = "fsl,p3060qds-fpga", "fsl,fpga-qixis";
+			reg = <3 0 0x100>;
+		};
+	};
+
+	pci0: pcie@ffe200000 {
+		reg = <0xf 0xfe200000 0 0x1000>;
+		ranges = <0x02000000 0 0xe0000000 0xc 0x00000000 0x0 0x20000000
+			  0x01000000 0 0x00000000 0xf 0xf8000000 0x0 0x00010000>;
+		pcie@0 {
+			ranges = <0x02000000 0 0xe0000000
+				  0x02000000 0 0xe0000000
+				  0 0x20000000
+
+				  0x01000000 0 0x00000000
+				  0x01000000 0 0x00000000
+				  0 0x00010000>;
+		};
+	};
+
+	pci1: pcie@ffe201000 {
+		reg = <0xf 0xfe201000 0 0x1000>;
+		ranges = <0x02000000 0x0 0xe0000000 0xc 0x20000000 0x0 0x20000000
+			  0x01000000 0x0 0x00000000 0xf 0xf8010000 0x0 0x00010000>;
+		pcie@0 {
+			ranges = <0x02000000 0 0xe0000000
+				  0x02000000 0 0xe0000000
+				  0 0x20000000
+
+				  0x01000000 0 0x00000000
+				  0x01000000 0 0x00000000
+				  0 0x00010000>;
+		};
+	};
+};

arch/powerpc/configs/corenet32_smp_defconfig

@@ -23,6 +23,7 @@ CONFIG_MODVERSIONS=y
 # CONFIG_BLK_DEV_BSG is not set
 CONFIG_P2041_RDB=y
 CONFIG_P3041_DS=y
+CONFIG_P3060_QDS=y
 CONFIG_P4080_DS=y
 CONFIG_P5020_DS=y
 CONFIG_HIGHMEM=y

arch/powerpc/platforms/85xx/Kconfig

@@ -197,6 +197,18 @@ config P3041_DS
 	help
 	  This option enables support for the P3041 DS board
 
+config P3060_QDS
+	bool "Freescale P3060 QDS"
+	select DEFAULT_UIMAGE
+	select PPC_E500MC
+	select PHYS_64BIT
+	select SWIOTLB
+	select MPC8xxx_GPIO
+	select HAS_RAPIDIO
+	select PPC_EPAPR_HV_PIC
+	help
+	  This option enables support for the P3060 QDS board
+
 config P4080_DS
 	bool "Freescale P4080 DS"
 	select DEFAULT_UIMAGE

arch/powerpc/platforms/85xx/Makefile

@@ -15,6 +15,7 @@ obj-$(CONFIG_P1022_DS)    += p1022_ds.o
 obj-$(CONFIG_P1023_RDS)   += p1023_rds.o
 obj-$(CONFIG_P2041_RDB)   += p2041_rdb.o corenet_ds.o
 obj-$(CONFIG_P3041_DS)    += p3041_ds.o corenet_ds.o
+obj-$(CONFIG_P3060_QDS)   += p3060_qds.o corenet_ds.o
 obj-$(CONFIG_P4080_DS)    += p4080_ds.o corenet_ds.o
 obj-$(CONFIG_P5020_DS)    += p5020_ds.o corenet_ds.o
 obj-$(CONFIG_STX_GP3)	  += stx_gp3.o

arch/powerpc/platforms/85xx/p3060_qds.c

+/*
+ * P3060 QDS Setup
+ *
+ * Copyright 2011 Freescale Semiconductor Inc.
+ *
+ * This program is free software; you can redistribute  it and/or modify it
+ * under  the terms of  the GNU General  Public License as published by the
+ * Free Software Foundation;  either version 2 of the  License, or (at your
+ * option) any later version.
+ */
+
+#include <linux/kernel.h>
+#include <linux/interrupt.h>
+#include <linux/phy.h>
+#include <asm/machdep.h>
+#include <asm/udbg.h>
+#include <asm/mpic.h>
+#include <linux/of_platform.h>
+#include <sysdev/fsl_soc.h>
+#include <sysdev/fsl_pci.h>
+#include <asm/ehv_pic.h>
+#include "corenet_ds.h"
+
+/*
+ * Called very early, device-tree isn't unflattened
+ */
+static int __init p3060_qds_probe(void)
+{
+	unsigned long root = of_get_flat_dt_root();
+#ifdef CONFIG_SMP
+	extern struct smp_ops_t smp_85xx_ops;
+#endif
+
+	if (of_flat_dt_is_compatible(root, "fsl,P3060QDS"))
+		return 1;
+
+	/* Check if we're running under the Freescale hypervisor */
+	if (of_flat_dt_is_compatible(root, "fsl,P3060QDS-hv")) {
+		ppc_md.init_IRQ = ehv_pic_init;
+		ppc_md.get_irq = ehv_pic_get_irq;
+		ppc_md.restart = fsl_hv_restart;
+		ppc_md.power_off = fsl_hv_halt;
+		ppc_md.halt = fsl_hv_halt;
+#ifdef CONFIG_SMP
+		/*
+		 * Disable the timebase sync operations because we can't write
+		 * to the timebase registers under the hypervisor.
+		 */
+		smp_85xx_ops.give_timebase = NULL;
+		smp_85xx_ops.take_timebase = NULL;
+#endif
+		return 1;
+	}
+
+	return 0;
+}
+
+define_machine(p3060_qds) {
+	.name			= "P3060 QDS",
+	.probe			= p3060_qds_probe,
+	.setup_arch		= corenet_ds_setup_arch,
+	.init_IRQ		= corenet_ds_pic_init,
+#ifdef CONFIG_PCI
+	.pcibios_fixup_bus	= fsl_pcibios_fixup_bus,
+#endif
+	.get_irq		= mpic_get_coreint_irq,
+	.restart		= fsl_rstcr_restart,
+	.calibrate_decr		= generic_calibrate_decr,
+	.progress		= udbg_progress,
+	.power_save		= e500_idle,
+};
+
+machine_device_initcall(p3060_qds, declare_of_platform_devices);
+
+#ifdef CONFIG_SWIOTLB
+machine_arch_initcall(p3060_qds, swiotlb_setup_bus_notifier);
+#endif