Commit 96fca1de authored by Scott Wood's avatar Scott Wood Committed by Kumar Gala

[POWERPC] Document local bus nodes in the device tree, and update cuboot-pq2.

The localbus node is used to describe devices that are connected via a chip
select or similar mechanism.  The advantages over placing the devices under
the root node are that it can be probed without probing other random things
under the root, and that the description of which chip select a given device
uses can be used to set up mappings if the firmware failed to do so in a
useful manner.

cuboot-pq2 is updated to match the binding; previously, it called itself
chipselect rather than localbus, and used phandle linkage between the
actual bus node and the control node (the current agreement is to simply use
the fully-qualified address of the control registers, and ignore the overlap
with the IMMR node).
Signed-off-by: default avatarScott Wood <scottwood@freescale.com>
Signed-off-by: default avatarKumar Gala <galak@kernel.crashing.org>
parent 2d2294ae
......@@ -2017,6 +2017,44 @@ platforms are moved over to use the flattened-device-tree model.
fsl,cpm-command = <2e600000>;
};
m) Chipselect/Local Bus
Properties:
- name : Should be localbus
- #address-cells : Should be either two or three. The first cell is the
chipselect number, and the remaining cells are the
offset into the chipselect.
- #size-cells : Either one or two, depending on how large each chipselect
can be.
- ranges : Each range corresponds to a single chipselect, and cover
the entire access window as configured.
Example:
localbus@f0010100 {
compatible = "fsl,mpc8272ads-localbus",
"fsl,mpc8272-localbus",
"fsl,pq2-localbus";
#address-cells = <2>;
#size-cells = <1>;
reg = <f0010100 40>;
ranges = <0 0 fe000000 02000000
1 0 f4500000 00008000>;
flash@0,0 {
compatible = "jedec-flash";
reg = <0 0 2000000>;
bank-width = <4>;
device-width = <1>;
};
board-control@1,0 {
reg = <1 0 20>;
compatible = "fsl,mpc8272ads-bcsr";
};
};
More devices will be defined as this spec matures.
VII - Specifying interrupt information for devices
......
......@@ -44,22 +44,21 @@ struct pci_range pci_ranges_buf[MAX_PROP_LEN / sizeof(struct pci_range)];
* some don't set up the PCI PIC at all, so we assume the device tree is
* sane and update the BRx registers appropriately.
*
* For any node defined as compatible with fsl,pq2-chipselect,
* #address/#size must be 2/1 for chipselect bus, 1/1 for parent bus,
* and ranges must be for whole chip selects.
* For any node defined as compatible with fsl,pq2-localbus,
* #address/#size must be 2/1 for the localbus, and 1/1 for the parent bus.
* Ranges must be for whole chip selects.
*/
static void update_cs_ranges(void)
{
u32 ctrl_ph;
void *ctrl_node, *bus_node, *parent_node;
void *bus_node, *parent_node;
u32 *ctrl_addr;
unsigned long ctrl_size;
u32 naddr, nsize;
int len;
int i;
bus_node = finddevice("/chipselect");
if (!bus_node || !dt_is_compatible(bus_node, "fsl,pq2-chipselect"))
bus_node = finddevice("/localbus");
if (!bus_node || !dt_is_compatible(bus_node, "fsl,pq2-localbus"))
return;
dt_get_reg_format(bus_node, &naddr, &nsize);
......@@ -74,19 +73,7 @@ static void update_cs_ranges(void)
if (naddr != 1 || nsize != 1)
goto err;
len = getprop(bus_node, "fsl,ctrl", &ctrl_ph, 4);
if (len != 4)
goto err;
ctrl_node = find_node_by_prop_value(NULL, "linux,phandle",
(char *)&ctrl_ph, 4);
if (!ctrl_node)
goto err;
if (!dt_is_compatible(ctrl_node, "fsl,pq2-chipselect-ctrl"))
goto err;
if (!dt_xlate_reg(ctrl_node, 0, (unsigned long *)&ctrl_addr,
if (!dt_xlate_reg(bus_node, 0, (unsigned long *)&ctrl_addr,
&ctrl_size))
goto err;
......@@ -123,7 +110,7 @@ static void update_cs_ranges(void)
return;
err:
printf("Bad /chipselect or fsl,pq2-chipselect-ctrl node\r\n");
printf("Bad /localbus node\r\n");
}
/* Older u-boots don't set PCI up properly. Update the hardware to match
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment