Merge tag 'imx-dt-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/dt

i.MX device tree changes for 5.14:

- New board support: i.MX6Q DaSheng COM-9XX SBC board, i.MX28 based XEA
  board, GE B1x5v2 boards.
- A series from Christoph Niedermaier to correct imx6q-dhcom
  descriptions, add device aliases and ethernet VIO regulator.
- Correct Ethernet node name for imx51-digi-connectcore-som and
  imx53-ard board to comply DT schema.
- A couple of update on imx6dl-yapp4 board, configuring OLED display
  segment offset, and using aliases to set custom MMC device indexes.
- A series from Oleksij Rempel and Robin van der Gracht to update
  Protonic boards: imx6dl-prtvt7, imx6dl-plym2m and imx6qdl-vicut1.
- A series from Shengjiu Wang to improve various audio support on NXP
  reference boards.
- Rename pinfunc for i.MX25 GPIO_[A-F] pads for consistency.

* tag 'imx-dt-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (30 commits)
  ARM: dts: imx6: Add GE B1x5v2
  ARM: dts: imx6q-dhcom: Add ethernet VIO regulator
  ARM: dts: imx6q-dhcom: Add aliases for i2c, serial and rtc
  ARM: dts: imx6q-dhcom: Add gpios pinctrl for i2c bus recovery
  ARM: dts: imx6q-dhcom: Fix ethernet plugin detection problems
  ARM: dts: imx6q-dhcom: Fix ethernet reset time properties
  ARM: dts: imx6dl-prtvt7: Remove unused 'sound-dai-cells' from ssi1 node
  ARM: dts: imx6dl-prtvt7: The sgtl5000 uses i2s not ac97
  ARM: dts: imx6qdl-vicut1: add interrupt-counter nodes
  ARM: dts: imx6dl-prtvt7: Enable the VPU
  ARM: dts: imx6dl: enable touchscreen debounce filter on PLYM2M and PRTVT7 boards
  ARM: dts: imx6dl-plym2m: remove touchscreen-size-* properties
  ARM: dts: imx6dl-prtvt7: fix PWM cell count for the backlight node.
  ARM: dts: imx6dl-prtvt7: Remove backlight enable gpio
  ARM: dts: imx6dl-prtvt7: add TSC2046 touchscreen node
  ARM: dts: imx53-ard: Correct Ethernet node name
  ARM: dts: i.MX51: digi-connectcore-som: Correct Ethernet node name
  ARM: dts: imx6dl-riotboard: configure PHY clock and set proper EEE value
  ARM: dts: imx6: edmqmx6: set phy-mode to RGMII-ID
  ARM: dts: imx6qdl-sabresd: Configure the gpio for hp detect
  ...

Link: https://lore.kernel.org/r/20210613082544.16067-4-shawnguo@kernel.orgSigned-off-by: Olof Johansson <olof@lixom.net>

arch/arm/boot/dts/Makefile

@@ -515,8 +515,14 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
 	imx6q-display5-tianma-tm070-1280x768.dtb \
 	imx6q-dmo-edmqmx6.dtb \
 	imx6q-dms-ba16.dtb \
+	imx6q-ds.dtb \
 	imx6q-emcon-avari.dtb \
 	imx6q-evi.dtb \
+	imx6dl-b105pv2.dtb \
+	imx6dl-b105v2.dtb \
+	imx6dl-b125v2.dtb \
+	imx6dl-b125pv2.dtb \
+	imx6dl-b155v2.dtb \
 	imx6q-gk802.dtb \
 	imx6q-gw51xx.dtb \
 	imx6q-gw52xx.dtb \
@@ -727,7 +733,8 @@ dtb-$(CONFIG_ARCH_MXS) += \
 	imx28-m28evk.dtb \
 	imx28-sps1.dtb \
 	imx28-ts4600.dtb \
-	imx28-tx28.dtb
+	imx28-tx28.dtb \
+	imx28-xea.dtb
 dtb-$(CONFIG_ARCH_NOMADIK) += \
 	ste-nomadik-s8815.dtb \
 	ste-nomadik-nhk15.dtb

arch/arm/boot/dts/imx25-pinfunc.h

@@ -563,15 +563,15 @@
 #define MX25_PAD_DE_B__DE_B			0x1f0 0x3ec 0x000 0x00 0x000
 #define MX25_PAD_DE_B__GPIO_2_20		0x1f0 0x3ec 0x000 0x05 0x000
 
-#define MX25_PAD_GPIO_A__GPIO_A			0x1f4 0x3f0 0x000 0x00 0x000
+#define MX25_PAD_GPIO_A__GPIO_1_0		0x1f4 0x3f0 0x000 0x00 0x000
 #define MX25_PAD_GPIO_A__CAN1_TX		0x1f4 0x3f0 0x000 0x06 0x000
 #define MX25_PAD_GPIO_A__USBOTG_PWR		0x1f4 0x3f0 0x000 0x02 0x000
 
-#define MX25_PAD_GPIO_B__GPIO_B			0x1f8 0x3f4 0x000 0x00 0x000
+#define MX25_PAD_GPIO_B__GPIO_1_1		0x1f8 0x3f4 0x000 0x00 0x000
 #define MX25_PAD_GPIO_B__USBOTG_OC		0x1f8 0x3f4 0x57c 0x02 0x001
 #define MX25_PAD_GPIO_B__CAN1_RX		0x1f8 0x3f4 0x480 0x06 0x001
 
-#define MX25_PAD_GPIO_C__GPIO_C			0x1fc 0x3f8 0x000 0x00 0x000
+#define MX25_PAD_GPIO_C__GPIO_1_2		0x1fc 0x3f8 0x000 0x00 0x000
 #define MX25_PAD_GPIO_C__PWM4_PWMO		0x1fc 0x3f8 0x000 0x01 0x000
 #define MX25_PAD_GPIO_C__I2C2_SCL		0x1fc 0x3f8 0x51c 0x02 0x001
 #define MX25_PAD_GPIO_C__KPP_COL4		0x1fc 0x3f8 0x52c 0x03 0x001
@@ -580,18 +580,18 @@
 #define MX25_PAD_GPIO_C__CAN2_TX		0x1fc 0x3f8 0x000 0x06 0x000
 #define MX25_PAD_GPIO_C__CSPI2_SS2		0x1fc 0x3f8 0x000 0x07 0x000
 
-#define MX25_PAD_GPIO_D__GPIO_D			0x200 0x3fc 0x000 0x00 0x000
+#define MX25_PAD_GPIO_D__GPIO_1_3		0x200 0x3fc 0x000 0x00 0x000
 #define MX25_PAD_GPIO_D__I2C2_SDA		0x200 0x3fc 0x520 0x02 0x001
 #define MX25_PAD_GPIO_D__CAN2_RX		0x200 0x3fc 0x484 0x06 0x001
 #define MX25_PAD_GPIO_D__CSPI3_SS2		0x200 0x3fc 0x4c4 0x07 0x001
 
-#define MX25_PAD_GPIO_E__GPIO_E			0x204 0x400 0x000 0x00 0x000
+#define MX25_PAD_GPIO_E__GPIO_1_4		0x204 0x400 0x000 0x00 0x000
 #define MX25_PAD_GPIO_E__I2C3_CLK		0x204 0x400 0x524 0x01 0x002
 #define MX25_PAD_GPIO_E__LD16			0x204 0x400 0x000 0x02 0x000
 #define MX25_PAD_GPIO_E__AUD7_TXD		0x204 0x400 0x000 0x04 0x000
 #define MX25_PAD_GPIO_E__UART4_RXD		0x204 0x400 0x570 0x06 0x002
 
-#define MX25_PAD_GPIO_F__GPIO_F			0x208 0x404 0x000 0x00 0x000
+#define MX25_PAD_GPIO_F__GPIO_1_5		0x208 0x404 0x000 0x00 0x000
 #define MX25_PAD_GPIO_F__LD17			0x208 0x404 0x000 0x02 0x000
 #define MX25_PAD_GPIO_F__AUD7_TXC		0x208 0x404 0x000 0x04 0x000
 #define MX25_PAD_GPIO_F__UART4_TXD		0x208 0x404 0x000 0x06 0x000

arch/arm/boot/dts/imx28-lwe.dtsi

+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2021
+ * Lukasz Majewski, DENX Software Engineering, lukma@denx.de
+ */
+
+/dts-v1/;
+#include "imx28.dtsi"
+
+/ {
+	aliases {
+		spi2 = &ssp3;
+	};
+
+	chosen {
+		bootargs = "root=/dev/mmcblk0p2 rootfstype=ext4 ro rootwait console=ttyAMA0,115200 panic=1";
+	};
+
+	memory@40000000 {
+		reg = <0x40000000 0x08000000>;
+	};
+
+	reg_3v3: regulator-reg-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	reg_usb_5v: regulator-reg-usb-5v {
+		compatible = "regulator-fixed";
+		regulator-name = "usb_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	reg_fec_3v3: regulator-reg-fec-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "fec-phy";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+};
+
+&duart {
+	pinctrl-names = "default";
+	pinctrl-0 = <&duart_pins_a>;
+	status = "okay";
+};
+
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins_a>;
+	status = "okay";
+};
+
+&saif0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&saif0_pins_a>;
+	#sound-dai-cells = <0>;
+	assigned-clocks = <&clks 53>;
+	assigned-clock-rates = <12000000>;
+	status = "okay";
+};
+
+&saif1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&saif1_pins_a>;
+	fsl,saif-master = <&saif0>;
+	#sound-dai-cells = <0>;
+	status = "okay";
+};
+
+&spi3_pins_a {
+	fsl,pinmux-ids = <
+		MX28_PAD_AUART2_RX__SSP3_D4
+		MX28_PAD_AUART2_TX__SSP3_D5
+		MX28_PAD_SSP3_SCK__SSP3_SCK
+		MX28_PAD_SSP3_MOSI__SSP3_CMD
+		MX28_PAD_SSP3_MISO__SSP3_D0
+		MX28_PAD_SSP3_SS0__SSP3_D3
+		MX28_PAD_AUART2_TX__GPIO_3_9
+	>;
+};
+
+&ssp0 {
+	compatible = "fsl,imx28-mmc";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc0_8bit_pins_a>;
+	bus-width = <8>;
+	vmmc-supply = <&reg_3v3>;
+	non-removable;
+	status = "okay";
+};
+
+&ssp2 {
+	compatible = "fsl,imx28-spi";
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi2_pins_a>;
+	status = "okay";
+};
+
+&ssp3 {
+	compatible = "fsl,imx28-spi";
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi3_pins_a>;
+	status = "okay";
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		spi-max-frequency = <40000000>;
+		reg = <0>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "u-boot";
+				reg = <0 0x80000>;
+				read-only;
+			};
+
+			partition@80000 {
+				label = "env0";
+				reg = <0x80000 0x10000>;
+			};
+
+			partition@90000 {
+				label = "env1";
+				reg = <0x90000 0x10000>;
+			};
+
+			partition@100000 {
+				label = "kernel";
+				reg = <0x100000 0x400000>;
+			};
+
+			partition@500000 {
+				label = "swupdate";
+				reg = <0x500000 0x800000>;
+			};
+		};
+	};
+};
+
+&usb0 {
+	vbus-supply = <&reg_usb_5v>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&usb0_pins_b>, <&usb0_id_pins_a>;
+	dr_mode = "host";
+	status = "okay";
+};
+
+&usbphy0 {
+	status = "okay";
+};
+
+&usb1 {
+	vbus-supply = <&reg_usb_5v>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&usb1_pins_b>;
+	dr_mode = "host";
+	status = "okay";
+};
+
+&usbphy1 {
+	status = "okay";
+};

arch/arm/boot/dts/imx28-xea.dts

+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2021
+ * Lukasz Majewski, DENX Software Engineering, lukma@denx.de
+ */
+
+/dts-v1/;
+#include "imx28-lwe.dtsi"
+
+/ {
+	compatible = "lwn,imx28-xea", "fsl,imx28";
+};
+
+&can0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&can1_pins_a>;
+	status = "okay";
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins_b>;
+	status = "okay";
+};
+
+&pinctrl {
+	pinctrl-names = "default";
+	pinctrl-0 = <&hog_pins_a &hog_pins_tiva>;
+
+	hog_pins_a: hog@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_GPMI_D00__GPIO_0_0
+			MX28_PAD_GPMI_D02__GPIO_0_2
+			MX28_PAD_GPMI_D05__GPIO_0_5
+			MX28_PAD_GPMI_CE1N__GPIO_0_17
+			MX28_PAD_GPMI_RDY0__GPIO_0_20
+			MX28_PAD_GPMI_RDY1__GPIO_0_21
+			MX28_PAD_GPMI_RDY2__GPIO_0_22
+			MX28_PAD_GPMI_RDN__GPIO_0_24
+			MX28_PAD_GPMI_CLE__GPIO_0_27
+			MX28_PAD_LCD_VSYNC__GPIO_1_28
+			MX28_PAD_SSP1_SCK__GPIO_2_12
+			MX28_PAD_SSP1_CMD__GPIO_2_13
+			MX28_PAD_SSP2_SS1__GPIO_2_20
+			MX28_PAD_SSP2_SS2__GPIO_2_21
+			MX28_PAD_LCD_D00__GPIO_1_0
+			MX28_PAD_LCD_D01__GPIO_1_1
+			MX28_PAD_LCD_D02__GPIO_1_2
+			MX28_PAD_LCD_D03__GPIO_1_3
+			MX28_PAD_LCD_D04__GPIO_1_4
+			MX28_PAD_LCD_D05__GPIO_1_5
+			MX28_PAD_LCD_D06__GPIO_1_6
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+
+	hog_pins_tiva: hog@1 {
+		reg = <1>;
+		fsl,pinmux-ids = <
+			MX28_PAD_GPMI_RDY3__GPIO_0_23
+			MX28_PAD_GPMI_WRN__GPIO_0_25
+		>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+
+	hog_pins_coding: hog@2 {
+		reg = <2>;
+		fsl,pinmux-ids = <
+			MX28_PAD_GPMI_D01__GPIO_0_1
+			MX28_PAD_GPMI_D03__GPIO_0_3
+			MX28_PAD_GPMI_D04__GPIO_0_4
+			MX28_PAD_GPMI_D06__GPIO_0_6
+			MX28_PAD_GPMI_D07__GPIO_0_7
+		>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+};
+
+&reg_fec_3v3 {
+	gpio = <&gpio0 0 0>;
+};
+
+&reg_usb_5v {
+	gpio = <&gpio0 2 0>;
+};
+
+&spi2_pins_a {
+	fsl,pinmux-ids = <
+		MX28_PAD_SSP2_SCK__SSP2_SCK
+		MX28_PAD_SSP2_MOSI__SSP2_CMD
+		MX28_PAD_SSP2_MISO__SSP2_D0
+		MX28_PAD_SSP2_SS0__GPIO_2_19
+	>;
+};

arch/arm/boot/dts/imx51-digi-connectcore-som.dtsi

@@ -206,7 +206,7 @@ &weim {
 	pinctrl-0 = <&pinctrl_weim>;
 	status = "okay";
 
-	lan9221: lan9221@5,0 {
+	lan9221: ethernet@5,0 {
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_lan9221>;
 		compatible = "smsc,lan9221", "smsc,lan9115";

arch/arm/boot/dts/imx53-ard.dts

@@ -24,7 +24,7 @@ eim-cs1@f4000000 {
 		reg = <0xf4000000 0x3ff0000>;
 		ranges;
 
-		lan9220@f4000000 {
+		ethernet@f4000000 {
 			compatible = "smsc,lan9220", "smsc,lan9115";
 			reg = <0xf4000000 0x2000000>;
 			phy-mode = "mii";

arch/arm/boot/dts/imx6dl-b105pv2.dts

+// SPDX-License-Identifier: GPL-2.0 or MIT
+//
+// Device Tree Source for General Electric B105Pv2
+//
+// Copyright 2018-2021 General Electric Company
+// Copyright 2018-2021 Collabora
+
+/dts-v1/;
+#include "imx6dl-b1x5pv2.dtsi"
+
+/ {
+	model = "General Electric B105Pv2";
+	compatible = "ge,imx6dl-b105pv2", "congatec,qmx6", "fsl,imx6dl";
+
+	panel {
+		compatible = "auo,g101evn010";
+	};
+};
+
+&i2c3 {
+	touchscreen@41 {
+		compatible = "ilitek,ili251x";
+		reg = <0x41>;
+		pinctrl-names = "default";
+		pinctrl-0 =<&pinctrl_q7_gpio0>;
+		interrupt-parent = <&gpio5>;
+		interrupts = <2 IRQ_TYPE_EDGE_FALLING>;
+		reset-gpios = <&tca6424a 21 GPIO_ACTIVE_LOW>;
+		touchscreen-size-x = <1280>;
+		touchscreen-size-y = <800>;
+	};
+};

arch/arm/boot/dts/imx6dl-b105v2.dts

+// SPDX-License-Identifier: GPL-2.0 or MIT
+//
+// Device Tree Source for General Electric B105v2
+//
+// Copyright 2018-2021 General Electric Company
+// Copyright 2018-2021 Collabora
+
+/dts-v1/;
+#include "imx6dl-b1x5v2.dtsi"
+
+/ {
+	model = "General Electric B105v2";
+	compatible = "ge,imx6dl-b105v2", "congatec,qmx6", "fsl,imx6dl";
+
+	panel {
+		compatible = "auo,g101evn010";
+	};
+};
+
+&i2c3 {
+	touchscreen@41 {
+		compatible = "ilitek,ili251x";
+		reg = <0x41>;
+		pinctrl-names = "default";
+		pinctrl-0 =<&pinctrl_q7_gpio0>;
+		interrupt-parent = <&gpio5>;
+		interrupts = <2 IRQ_TYPE_EDGE_FALLING>;
+		reset-gpios = <&tca6424a 21 GPIO_ACTIVE_LOW>;
+		touchscreen-size-x = <1280>;
+		touchscreen-size-y = <800>;
+	};
+};

arch/arm/boot/dts/imx6dl-b125pv2.dts

+// SPDX-License-Identifier: GPL-2.0 or MIT
+//
+// Device Tree Source for General Electric B125Pv2
+//
+// Copyright 2018-2021 General Electric Company
+// Copyright 2018-2021 Collabora
+
+/dts-v1/;
+#include "imx6dl-b1x5pv2.dtsi"
+
+/ {
+	model = "General Electric B125Pv2";
+	compatible = "ge,imx6dl-b125pv2", "congatec,qmx6", "fsl,imx6dl";
+
+	panel {
+		compatible = "auo,g121ean01";
+	};
+};
+
+&i2c3 {
+	touchscreen@2a {
+		compatible = "eeti,exc80h60";
+		reg = <0x2a>;
+		pinctrl-names = "default";
+		pinctrl-0 =<&pinctrl_q7_gpio0>;
+		interrupt-parent = <&gpio5>;
+		interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
+		reset-gpios = <&tca6424a 21 GPIO_ACTIVE_HIGH>;
+	};
+};

arch/arm/boot/dts/imx6dl-b125v2.dts

+// SPDX-License-Identifier: GPL-2.0 or MIT
+//
+// Device Tree Source for General Electric B125v2
+//
+// Copyright 2018-2021 General Electric Company
+// Copyright 2018-2021 Collabora
+
+/dts-v1/;
+#include "imx6dl-b1x5v2.dtsi"
+
+/ {
+	model = "General Electric B125v2";
+	compatible = "ge,imx6dl-b125v2", "congatec,qmx6", "fsl,imx6dl";
+
+	panel {
+		compatible = "auo,g121ean01";
+	};
+};
+
+&i2c3 {
+	touchscreen@2a {
+		compatible = "eeti,exc80h60";
+		reg = <0x2a>;
+		pinctrl-names = "default";
+		pinctrl-0 =<&pinctrl_q7_gpio0>;
+		interrupt-parent = <&gpio5>;
+		interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
+		reset-gpios = <&tca6424a 21 GPIO_ACTIVE_HIGH>;
+	};
+};

arch/arm/boot/dts/imx6dl-b155v2.dts

+// SPDX-License-Identifier: GPL-2.0 or MIT
+//
+// Device Tree Source for General Electric B155v2
+//
+// Copyright 2018-2021 General Electric Company
+// Copyright 2018-2021 Collabora
+
+/dts-v1/;
+#include "imx6dl-b1x5v2.dtsi"
+
+/ {
+	model = "General Electric B155v2";
+	compatible = "ge,imx6dl-b155v2", "congatec,qmx6", "fsl,imx6dl";
+
+	panel {
+		compatible = "auo,g156xtn01";
+	};
+};
+
+&i2c3 {
+	touchscreen@2a {
+		compatible = "eeti,exc80h84";
+		reg = <0x2a>;
+		pinctrl-names = "default";
+		pinctrl-0 =<&pinctrl_q7_gpio0>;
+		interrupt-parent = <&gpio5>;
+		interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
+		touchscreen-inverted-x;
+		touchscreen-inverted-y;
+		reset-gpios = <&tca6424a 21 GPIO_ACTIVE_HIGH>;
+	};
+};

arch/arm/boot/dts/imx6dl-b1x5pv2.dtsi

+// SPDX-License-Identifier: GPL-2.0 or MIT
+//
+// Device Tree Source for General Electric B1x5Pv2
+// patient monitor series
+//
+// Copyright 2018-2021 General Electric Company
+// Copyright 2018-2021 Collabora
+
+#include <dt-bindings/input/input.h>
+#include "imx6dl-qmx6.dtsi"
+
+/ {
+	chosen {
+		stdout-path = &uart3;
+	};
+
+	/* Do not allow frequencies above 800MHz */
+	cpus {
+		cpu@0 {
+			operating-points = <
+				/* kHz    uV */
+				792000  1175000
+				396000  1150000
+			>;
+			fsl,soc-operating-points = <
+				/* ARM kHz	SOC-PU uV */
+				792000	1175000
+				396000	1175000
+			>;
+		};
+
+		cpu@1 {
+			operating-points = <
+				/* kHz    uV */
+				792000  1175000
+				396000  1150000
+			>;
+			fsl,soc-operating-points = <
+				/* ARM kHz	SOC-PU uV */
+				792000	1175000
+				396000	1175000
+			>;
+		};
+	};
+
+	reg_syspwr: regulator-12v {
+		compatible = "regulator-fixed";
+		regulator-name = "SYS_PWR";
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+	};
+
+	reg_5v_pmc: regulator-5v-pmc {
+		compatible = "regulator-fixed";
+		regulator-name = "5V PMC";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&reg_syspwr>;
+	};
+
+	reg_5v: regulator-5v {
+		compatible = "regulator-fixed";
+		regulator-name = "5V";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&reg_syspwr>;
+	};
+
+	reg_3v3: regulator-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&reg_syspwr>;
+	};
+
+	reg_5v0_audio: regulator-5v0-audio {
+		compatible = "regulator-fixed";
+		regulator-name = "5V0_AUDIO";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&reg_5v>;
+		gpio = <&tca6424a 16 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		/*
+		 * This must be always-on for da7212, which has some not
+		 * properly documented dependencies for it's speaker supply
+		 * pin. The issue manifests as speaker volume being very low.
+		 */
+		regulator-always-on;
+	};
+
+
+	reg_3v3_audio: regulator-3v3-audio {
+		compatible = "regulator-fixed";
+		regulator-name = "3V3_AUDIO";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&reg_3v3>;
+		pinctrl-0 = <&pinctrl_q7_hda_reset>;
+		pinctrl-names = "default";
+		gpio = <&gpio6 8 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	reg_2v5_audio: regulator-2v5-audio {
+		compatible = "regulator-fixed";
+		regulator-name = "2V5_AUDIO";
+		regulator-min-microvolt = <2500000>;
+		regulator-max-microvolt = <2500000>;
+		regulator-always-on;
+		vin-supply = <&reg_3v3_audio>;
+
+	};
+
+	reg_wlan: regulator-wlan {
+		compatible = "regulator-fixed";
+		regulator-name = "WLAN";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&reg_3v3>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_q7_sdio_power>;
+		gpio = <&gpio4 30 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		startup-delay-us = <70000>;
+	};
+
+	reg_bl: regulator-backlight {
+		compatible = "regulator-fixed";
+		regulator-name = "LED_VCC";
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+		vin-supply = <&reg_syspwr>;
+		pinctrl-0 = <&pinctrl_q7_lcd_power>;
+		pinctrl-names = "default";
+		gpio = <&gpio1 7 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	reg_lcd: regulator-lcd {
+		compatible = "regulator-fixed";
+		regulator-name = "LCD_5V";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&reg_5v>;
+	};
+
+	usb_power: regulator-usb-power {
+		compatible = "regulator-fixed";
+		regulator-name = "USB POWER";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&reg_5v>;
+	};
+
+	charger: battery-charger {
+		compatible = "gpio-charger"; /* ti,bq24172 */
+		charger-type = "mains";
+		gpios = <&tca6424a 3 GPIO_ACTIVE_LOW>;
+		charge-current-limit-gpios = <&tca6424a 11 GPIO_ACTIVE_HIGH>,
+					     <&tca6424a 12 GPIO_ACTIVE_HIGH>;
+		charge-current-limit-mapping = <1300000 0x0>,
+					       <700000 0x1>,
+					       <0 0x2>;
+		charge-status-gpios = <&tca6424a 6 GPIO_ACTIVE_HIGH>;
+	};
+
+	poweroff {
+		compatible = "gpio-poweroff";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_q7_spi_cs1>;
+		gpios = <&gpio4 25 GPIO_ACTIVE_LOW>;
+	};
+
+	power-button-key {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_q7_sleep_button>;
+
+		power-button {
+			label = "power button";
+			gpios = <&gpio4 7 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_POWER>;
+		};
+	};
+
+	rotary-encoder-key {
+		compatible = "gpio-keys";
+
+		rotary-encoder-press {
+			label = "rotary-encoder press";
+			gpios = <&tca6424a 0 GPIO_ACTIVE_HIGH>;
+			linux,code = <KEY_ENTER>;
+			linux,can-disable;
+		};
+	};
+
+	rotary-encoder {
+		compatible = "rotary-encoder";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_q7_gpio2 &pinctrl_q7_gpio4>;
+		gpios = <&gpio4 26 GPIO_ACTIVE_LOW>, <&gpio1 0 GPIO_ACTIVE_LOW>;
+		rotary-encoder,relative-axis;
+		rotary-encoder,steps-per-period = <2>;
+		wakeup-source;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_q7_gpio1 &pinctrl_q7_gpio3 &pinctrl_q7_gpio5>;
+
+		alarm1 {
+			label = "alarm:red";
+			gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
+		};
+
+		alarm2 {
+			label = "alarm:yellow";
+			gpios = <&gpio4 27 GPIO_ACTIVE_HIGH>;
+		};
+
+		alarm3 {
+			label = "alarm:blue";
+			gpios = <&gpio4 15 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_q7_backlight_enable>;
+		power-supply = <&reg_bl>;
+		pwms = <&pwm4 0 5000000 0>;
+		brightness-levels = <0 255>;
+		num-interpolated-steps = <255>;
+		default-brightness-level = <179>;
+		enable-gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>;
+	};
+
+	panel {
+		backlight = <&backlight>;
+		power-supply = <&reg_lcd>;
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&lvds0_out>;
+			};
+		};
+	};
+
+	sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,name = "audio-card";
+		simple-audio-card,format = "i2s";
+		simple-audio-card,bitclock-master = <&dailink_master>;
+		simple-audio-card,frame-master = <&dailink_master>;
+		simple-audio-card,widgets = "Speaker", "Ext Spk";
+		simple-audio-card,audio-routing = "Ext Spk", "LINE";
+
+		simple-audio-card,cpu {
+			sound-dai = <&ssi1>;
+		};
+
+		dailink_master: simple-audio-card,codec {
+			sound-dai = <&codec>;
+		};
+	};
+
+	clk_ext_audio_codec: clock-codec {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <12288000>;
+	};
+};
+
+&audmux {
+	status = "okay";
+};
+
+&fec {
+	status = "okay";
+};
+
+&hdmi {
+	status = "okay";
+};
+
+&i2c1 {
+	battery: battery@b {
+		compatible = "ti,bq20z65", "sbs,sbs-battery";
+		reg = <0x0b>;
+		sbs,battery-detect-gpios = <&tca6424a 5 GPIO_ACTIVE_LOW>;
+		sbs,i2c-retry-count = <5>;
+		power-supplies = <&charger>;
+	};
+
+	codec: audio-codec@1a {
+		compatible = "dlg,da7212";
+		reg = <0x1a>;
+		#sound-dai-cells = <0>;
+		VDDA-supply = <&reg_2v5_audio>;
+		VDDSP-supply = <&reg_5v0_audio>;
+		VDDMIC-supply = <&reg_3v3_audio>;
+		VDDIO-supply = <&reg_3v3_audio>;
+		clocks = <&clk_ext_audio_codec>;
+		clock-names = "mclk";
+	};
+};
+
+&i2c5 {
+	tca6424a: gpio-controller@22 {
+		compatible = "ti,tca6424";
+		reg = <0x22>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		vcc-supply = <&reg_3v3>;
+		interrupt-parent = <&gpio7>;
+		interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_q7_gpio6>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		gpio-line-names = "GPIO_ROTOR#", "ACM_IO_INT", "TMP_SENSOR_IRQ", "AC_IN",
+				  "TF_S", "BATT_T", "LED_INC_CHAR", "ACM1_OCF",
+				  "ACM2_OCF", "ACM_IO_RST", "USB1_POWER_EN", "EGPIO_CC_CTL0",
+				  "EGPIO_CC_CTL1", "12V_OEMNBP_EN", "CP2105_RST", "",
+				  "SPEAKER_PA_EN", "ARM7_UPI_RESET", "ARM7_PWR_RST", "NURSE_CALL",
+				  "MARKER_EN", "EGPIO_TOUCH_RST", "PRESSURE_INT1", "PRESSURE_INT2";
+
+	};
+
+	tmp75: temperature-sensor@48 {
+		compatible = "ti,tmp75";
+		reg = <0x48>;
+		vs-supply = <&reg_3v3>;
+		interrupt-parent = <&tca6424a>;
+		interrupts = <2 IRQ_TYPE_EDGE_FALLING>;
+	};
+};
+
+&ldb {
+	status = "okay";
+
+	lvds0: lvds-channel@0 {
+		status = "okay";
+		fsl,data-mapping = "spwg";
+		fsl,data-width = <24>;
+
+		port@4 {
+			reg = <4>;
+
+			lvds0_out: endpoint {
+				remote-endpoint = <&panel_in>;
+			};
+		};
+	};
+};
+
+&pwm4 {
+	status = "okay";
+};
+
+&ssi1 {
+	fsl,mode = "i2s-slave";
+	status = "okay";
+};
+
+&usbotg {
+	vbus-supply = <&usb_power>;
+	disable-over-current;
+	dr_mode = "host";
+	status = "okay";
+
+	/*
+	 * TPS2051BDGN fault-gpio is connected to Q7[86] USB_0_1_OC_N.
+	 * On QMX6 this is not connceted to the i.MX6, but to the USB Hub
+	 * from &usbh1. This means, that we cannot easily detect and handle
+	 * over-current events. Fortunately the regulator limits the current
+	 * automatically, so the hardware is still protected.
+	 */
+};
+
+&usdhc4 {
+	/* WiFi module */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc4>;
+	bus-width = <4>;
+	no-1-8-v;
+	non-removable;
+	wakeup-source;
+	keep-power-in-suspend;
+	cap-power-off-card;
+	max-frequency = <25000000>;
+	vmmc-supply = <&reg_wlan>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+
+	wlcore: wlcore@2 {
+		compatible = "ti,wl1837";
+		reg = <2>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_q7_gpio7>;
+
+		interrupt-parent = <&gpio4>;
+		interrupts = <14 IRQ_TYPE_LEVEL_HIGH>;
+
+		tcxo-clock-frequency = <26000000>;
+	};
+};

arch/arm/boot/dts/imx6dl-b1x5v2.dtsi

+// SPDX-License-Identifier: GPL-2.0 or MIT
+//
+// Device Tree Source for General Electric B1x5v2
+// patient monitor series
+//
+// Copyright 2018-2021 General Electric Company
+// Copyright 2018-2021 Collabora
+
+#include <dt-bindings/input/input.h>
+#include "imx6dl-b1x5pv2.dtsi"
+
+/ {
+	reg_3v3_acm: regulator-3v3-acm {
+		compatible = "regulator-fixed";
+		regulator-name = "3V3 ACM";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+		vin-supply = <&reg_3v3>;
+	};
+};
+
+&i2c1 {
+	tca6416: gpio-controller@21 {
+		compatible = "ti,tca6416";
+		reg = <0x21>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		reset-gpios = <&tca6424a 9 GPIO_ACTIVE_LOW>;
+		vcc-supply = <&reg_3v3_acm>;
+		gpio-line-names = "ACM1_EN", "ACM1_CL0", "ACM1_CL1", "ACM1_CL2",
+				  "", "ACM2_EN", "ACM2_CL0", "ACM2_CL1",
+				  "ACM2_CL2", "", "", "",
+				  "", "", "", "";
+
+		/*
+		 * The interrupt pin is connected to &tca6424a pin 1, but the Linux
+		 * TCA6424 driver cannot handle low type interrupts at the moment
+		 * (and support cannot be added without some ugly hacks). Since this
+		 * controller does not have any input type GPIOs, just pretend
+		 * that the interrupt pin is unconnected.
+		 */
+	};
+};
+
+&i2c5 {
+	mpl3115a2: pressure-sensor@60 {
+		compatible = "fsl,mpl3115";
+		reg = <0x60>;
+		vcc-supply = <&reg_3v3_acm>;
+
+		/*
+		 * The MPL3115 interrupts are connected to pin 22 and 23
+		 * of &tca6424a, but the binding does not yet support
+		 * interrupts.
+		 */
+	};
+};

arch/arm/boot/dts/imx6dl-plym2m.dts

@@ -138,8 +138,6 @@ touchscreen@0 {
 		interrupts-extended = <&gpio3 20 IRQ_TYPE_EDGE_FALLING>;
 		pendown-gpio = <&gpio3 20 GPIO_ACTIVE_LOW>;
 
-		touchscreen-size-x = <800>;
-		touchscreen-size-y = <480>;
 		touchscreen-inverted-x;
 		touchscreen-inverted-y;
 		touchscreen-max-pressure = <4095>;
@@ -147,7 +145,9 @@ touchscreen@0 {
 		ti,vref-delay-usecs = /bits/ 16 <100>;
 		ti,x-plate-ohms = /bits/ 16 <800>;
 		ti,y-plate-ohms = /bits/ 16 <300>;
-
+		ti,debounce-max = /bits/ 16 <3>;
+		ti,debounce-tol = /bits/ 16 <70>;
+		ti,debounce-rep = /bits/ 16 <3>;
 		wakeup-source;
 	};
 };

arch/arm/boot/dts/imx6dl-prtvt7.dts

@@ -21,14 +21,11 @@ memory@10000000 {
 
 	backlight_lcd: backlight-lcd {
 		compatible = "pwm-backlight";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_backlight>;
-		pwms = <&pwm1 0 500000>;
+		pwms = <&pwm1 0 500000 0>;
 		brightness-levels = <0 20 81 248 1000>;
 		default-brightness-level = <20>;
 		num-interpolated-steps = <21>;
 		power-supply = <&reg_bl_12v0>;
-		enable-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>;
 	};
 
 	keys {
@@ -223,6 +220,24 @@ &ecspi2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_ecspi2>;
 	status = "okay";
+
+	touchscreen@0 {
+		compatible = "ti,tsc2046";
+		reg = <0>;
+		pinctrl-0 = <&pinctrl_tsc>;
+		pinctrl-names ="default";
+		spi-max-frequency = <100000>;
+		interrupts-extended = <&gpio3 20 IRQ_TYPE_EDGE_FALLING>;
+		pendown-gpio = <&gpio3 20 GPIO_ACTIVE_LOW>;
+		touchscreen-max-pressure = <4095>;
+		ti,vref-delay-usecs = /bits/ 16 <100>;
+		ti,x-plate-ohms = /bits/ 16 <800>;
+		ti,y-plate-ohms = /bits/ 16 <300>;
+		ti,debounce-max = /bits/ 16 <3>;
+		ti,debounce-tol = /bits/ 16 <70>;
+		ti,debounce-rep = /bits/ 16 <3>;
+		wakeup-source;
+	};
 };
 
 &i2c1 {
@@ -261,7 +276,6 @@ &ipu1 {
 };
 
 &pwm1 {
-	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm1>;
 	status = "okay";
@@ -276,8 +290,6 @@ &snvs_pwrkey {
 };
 
 &ssi1 {
-	#sound-dai-cells = <0>;
-	fsl,mode = "ac97-slave";
 	status = "okay";
 };
 
@@ -285,10 +297,6 @@ &usbh1 {
 	status = "disabled";
 };
 
-&vpu {
-	status = "disabled";
-};
-
 &iomuxc {
 	pinctrl_audmux: audmuxgrp {
 		fsl,pins = <
@@ -300,12 +308,6 @@ MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS		0x130b0
 		>;
 	};
 
-	pinctrl_backlight: backlightgrp {
-		fsl,pins = <
-			MX6QDL_PAD_DISP0_DAT7__GPIO4_IO28	0x1b0b0
-		>;
-	};
-
 	pinctrl_can1phy: can1phy {
 		fsl,pins = <
 			/* CAN1_SR */

arch/arm/boot/dts/imx6dl-riotboard.dts

@@ -106,6 +106,8 @@ rgmii_phy: ethernet-phy@4 {
 			reset-gpios = <&gpio3 31 GPIO_ACTIVE_LOW>;
 			reset-assert-us = <10000>;
 			reset-deassert-us = <1000>;
+			qca,smarteee-tw-us-1g = <24>;
+			qca,clk-out-frequency = <125000000>;
 		};
 	};
 };

arch/arm/boot/dts/imx6dl-yapp4-common.dtsi

@@ -11,6 +11,8 @@ / {
 	aliases: aliases {
 		ethernet1 = &eth1;
 		ethernet2 = &eth2;
+		mmc0 = &usdhc3;
+		mmc1 = &usdhc4;
 	};
 
 	backlight: backlight {
@@ -341,6 +343,7 @@ oled_1305: oled@3d {
 		solomon,height = <64>;
 		solomon,width = <128>;
 		solomon,page-offset = <0>;
+		solomon,col-offset = <4>;
 		solomon,prechargep2 = <15>;
 		reset-gpios = <&gpio_oled 1 GPIO_ACTIVE_LOW>;
 		vbat-supply = <&sw2_reg>;

arch/arm/boot/dts/imx6q-dhcom-som.dtsi

@@ -12,10 +12,20 @@
 
 / {
 	aliases {
+		i2c0 = &i2c2;
+		i2c1 = &i2c1;
+		i2c2 = &i2c3;
 		mmc0 = &usdhc2;
 		mmc1 = &usdhc3;
 		mmc2 = &usdhc4;
 		mmc3 = &usdhc1;
+		rtc0 = &rtc_i2c;
+		rtc1 = &snvs_rtc;
+		serial0 = &uart1;
+		serial1 = &uart5;
+		serial2 = &uart4;
+		serial3 = &uart2;
+		serial4 = &uart3;
 	};
 
 	memory@10000000 {
@@ -23,6 +33,19 @@ memory@10000000 {
 		reg = <0x10000000 0x40000000>;
 	};
 
+	reg_eth_vio: regulator-eth-vio {
+		compatible = "regulator-fixed";
+		gpio = <&gpio1 7 GPIO_ACTIVE_LOW>;
+		pinctrl-0 = <&pinctrl_enet_vio>;
+		pinctrl-names = "default";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-name = "eth_vio";
+		vin-supply = <&sw2_reg>;
+	};
+
 	reg_usb_otg_vbus: regulator-usb-otg-vbus {
 		compatible = "regulator-fixed";
 		regulator-name = "usb_otg_vbus";
@@ -96,30 +119,40 @@ ethphy0: ethernet-phy@0 {	/* SMSC LAN8710Ai */
 			reg = <0>;
 			max-speed = <100>;
 			reset-gpios = <&gpio5 0 GPIO_ACTIVE_LOW>;
-			reset-delay-us = <1000>;
-			reset-post-delay-us = <1000>;
+			reset-assert-us = <1000>;
+			reset-deassert-us = <1000>;
+			smsc,disable-energy-detect; /* Make plugin detection reliable */
 		};
 	};
 };
 
 &i2c1 {
 	clock-frequency = <100000>;
-	pinctrl-names = "default";
+	pinctrl-names = "default", "gpio";
 	pinctrl-0 = <&pinctrl_i2c1>;
+	pinctrl-1 = <&pinctrl_i2c1_gpio>;
+	scl-gpios = <&gpio3 21 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio3 28 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 	status = "okay";
 };
 
 &i2c2 {
 	clock-frequency = <100000>;
-	pinctrl-names = "default";
+	pinctrl-names = "default", "gpio";
 	pinctrl-0 = <&pinctrl_i2c2>;
+	pinctrl-1 = <&pinctrl_i2c2_gpio>;
+	scl-gpios = <&gpio4 12 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio4 13 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 	status = "okay";
 };
 
 &i2c3 {
 	clock-frequency = <100000>;
-	pinctrl-names = "default";
+	pinctrl-names = "default", "gpio";
 	pinctrl-0 = <&pinctrl_i2c3>;
+	pinctrl-1 = <&pinctrl_i2c3_gpio>;
+	scl-gpios = <&gpio1 3 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio1 6 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 	status = "okay";
 
 	ltc3676: pmic@3c {
@@ -203,7 +236,7 @@ eeprom@50 {
 		pagesize = <16>;
 	};
 
-	rtc@56 {
+	rtc_i2c: rtc@56 {
 		compatible = "microcrystal,rv3029";
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_rtc_hw300>;
@@ -260,6 +293,11 @@ MX6QDL_PAD_ENET_TXD1__ENET_TX_DATA1	0x1b0b0
 			MX6QDL_PAD_GPIO_16__ENET_REF_CLK	0x4001b0a8
 			MX6QDL_PAD_EIM_WAIT__GPIO5_IO00		0x000b0
 			MX6QDL_PAD_KEY_ROW4__GPIO4_IO15		0x000b1
+		>;
+	};
+
+	pinctrl_enet_vio: enet-vio-grp {
+		fsl,pins = <
 			MX6QDL_PAD_GPIO_7__GPIO1_IO07		0x120b0
 		>;
 	};
@@ -285,6 +323,13 @@ MX6QDL_PAD_EIM_D28__I2C1_SDA		0x4001b8b1
 		>;
 	};
 
+	pinctrl_i2c1_gpio: i2c1-gpio-grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D21__GPIO3_IO21		0x4001b8b1
+			MX6QDL_PAD_EIM_D28__GPIO3_IO28		0x4001b8b1
+		>;
+	};
+
 	pinctrl_i2c2: i2c2-grp {
 		fsl,pins = <
 			MX6QDL_PAD_KEY_COL3__I2C2_SCL		0x4001b8b1
@@ -292,6 +337,13 @@ MX6QDL_PAD_KEY_ROW3__I2C2_SDA		0x4001b8b1
 		>;
 	};
 
+	pinctrl_i2c2_gpio: i2c2-gpio-grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL3__GPIO4_IO12		0x4001b8b1
+			MX6QDL_PAD_KEY_ROW3__GPIO4_IO13		0x4001b8b1
+		>;
+	};
+
 	pinctrl_i2c3: i2c3-grp {
 		fsl,pins = <
 			MX6QDL_PAD_GPIO_3__I2C3_SCL		0x4001b8b1
@@ -299,6 +351,13 @@ MX6QDL_PAD_GPIO_6__I2C3_SDA		0x4001b8b1
 		>;
 	};
 
+	pinctrl_i2c3_gpio: i2c3-gpio-grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_3__GPIO1_IO03		0x4001b8b1
+			MX6QDL_PAD_GPIO_6__GPIO1_IO06		0x4001b8b1
+		>;
+	};
+
 	pinctrl_pmic_hw300: pmic-hw300-grp {
 		fsl,pins = <
 			MX6QDL_PAD_EIM_A25__GPIO5_IO02		0x1B0B0

arch/arm/boot/dts/imx6q-dmo-edmqmx6.dts

@@ -112,7 +112,7 @@ flash: m25p80@0 {
 &fec {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet>;
-	phy-mode = "rgmii";
+	phy-mode = "rgmii-id";
 	phy-reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
 	phy-supply = <&vgen2_1v2_eth>;
 	status = "okay";

arch/arm/boot/dts/imx6q-ds.dts

+// SPDX-License-Identifier: GPL-2.0+
+//
+// Copyright 2021 Dillon Min <dillon.minfei@gmail.com>
+//
+// Based on imx6qdl-sabresd.dtsi which is:
+// Copyright 2012 Freescale Semiconductor, Inc.
+// Copyright 2011 Linaro Ltd.
+
+/dts-v1/;
+
+#include "imx6q.dtsi"
+#include "imx6qdl-ds.dtsi"
+
+/ {
+	model = "DaSheng i.MX6 Quad Com-9xx Board";
+	compatible = "ds,imx6q-sbc", "fsl,imx6q";
+};

arch/arm/boot/dts/imx6qdl-phytec-pfla02.dtsi

@@ -322,8 +322,8 @@ pinctrl_uart3: uart3grp {
 			fsl,pins = <
 				MX6QDL_PAD_EIM_D24__UART3_TX_DATA	0x1b0b1
 				MX6QDL_PAD_EIM_D25__UART3_RX_DATA	0x1b0b1
-				MX6QDL_PAD_EIM_D30__UART3_RTS_B		0x1b0b1
-				MX6QDL_PAD_EIM_D31__UART3_CTS_B		0x1b0b1
+				MX6QDL_PAD_EIM_D31__UART3_RTS_B		0x1b0b1
+				MX6QDL_PAD_EIM_D30__UART3_CTS_B		0x1b0b1
 			>;
 		};
 
@@ -410,6 +410,7 @@ &reg_soc {
 &uart3 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_uart3>;
+	uart-has-rtscts;
 	status = "disabled";
 };
 

arch/arm/boot/dts/imx6qdl-sabresd.dtsi

@@ -97,8 +97,11 @@ sound {
 		compatible = "fsl,imx6q-sabresd-wm8962",
 			   "fsl,imx-audio-wm8962";
 		model = "wm8962-audio";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_hp>;
 		ssi-controller = <&ssi2>;
 		audio-codec = <&codec>;
+		audio-asrc = <&asrc>;
 		audio-routing =
 			"Headphone Jack", "HPOUTL",
 			"Headphone Jack", "HPOUTR",
@@ -545,6 +548,13 @@ MX6QDL_PAD_KEY_ROW2__HDMI_TX_CEC_LINE	0x1f8b0
 			>;
 		};
 
+		pinctrl_hp: hpgrp {
+			fsl,pins = <
+				MX6QDL_PAD_SD3_RST__GPIO7_IO08          0x1b0b0
+				MX6QDL_PAD_GPIO_9__GPIO1_IO09           0x1b0b0
+			>;
+		};
+
 		pinctrl_i2c1: i2c1grp {
 			fsl,pins = <
 				MX6QDL_PAD_CSI0_DAT8__I2C1_SDA		0x4001b8b1

arch/arm/boot/dts/imx6qdl-vicut1.dtsi

@@ -40,6 +40,27 @@ comp0_out: endpoint {
 		};
 	};
 
+	counter-0 {
+		compatible = "interrupt-counter";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_counter0>;
+		gpios = <&gpio2 0 GPIO_ACTIVE_LOW>;
+	};
+
+	counter-1 {
+		compatible = "interrupt-counter";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_counter1>;
+		gpios = <&gpio2 1 GPIO_ACTIVE_LOW>;
+	};
+
+	counter-2 {
+		compatible = "interrupt-counter";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_counter2>;
+		gpios = <&gpio2 2 GPIO_ACTIVE_LOW>;
+	};
+
 	gpio-keys {
 		compatible = "gpio-keys";
 		autorepeat;
@@ -254,7 +275,7 @@ &gpio1 {
 
 &gpio2 {
 	gpio-line-names =
-		"", "", "", "", "", "", "", "",
+		"count0", "count1", "count2", "", "", "", "", "",
 		"REV_ID0", "REV_ID1", "REV_ID2", "REV_ID3", "REV_ID4",
 			"BOARD_ID0", "BOARD_ID1", "BOARD_ID2",
 		"", "", "", "", "", "", "", "ON_SWITCH",
@@ -572,6 +593,24 @@ MX6QDL_PAD_KEY_ROW3__GPIO4_IO13			0x13008
 		>;
 	};
 
+	pinctrl_counter0: counter0grp {
+		fsl,pins = <
+			MX6QDL_PAD_NANDF_D0__GPIO2_IO00			0x1b000
+		>;
+	};
+
+	pinctrl_counter1: counter1grp {
+		fsl,pins = <
+			MX6QDL_PAD_NANDF_D1__GPIO2_IO01			0x1b000
+		>;
+	};
+
+	pinctrl_counter2: counter2grp {
+		fsl,pins = <
+			MX6QDL_PAD_NANDF_D2__GPIO2_IO02			0x1b000
+		>;
+	};
+
 	pinctrl_ecspi1: ecspi1grp {
 		fsl,pins = <
 			MX6QDL_PAD_EIM_D17__ECSPI1_MISO			0x100b1

arch/arm/boot/dts/imx6qdl-wandboard-revd1.dtsi

@@ -142,7 +142,6 @@ &iomuxc {
 	imx6qdl-wandboard {
 		pinctrl_hog: hoggrp {
 			fsl,pins = <
-				MX6QDL_PAD_EIM_D22__USB_OTG_PWR		0x80000000	/* USB Power Enable */
 				MX6QDL_PAD_GPIO_2__GPIO1_IO02		0x80000000	/* USDHC1 CD */
 				MX6QDL_PAD_EIM_DA9__GPIO3_IO09		0x80000000	/* uSDHC3 CD */
 				MX6QDL_PAD_EIM_D29__GPIO3_IO29   	0x1f0b1		/* RGMII PHY reset */

arch/arm/boot/dts/imx6ul-14x14-evk.dtsi

@@ -60,38 +60,26 @@ reg_can_3v3: regulator-can-3v3 {
 		gpios = <&gpio_spi 3 GPIO_ACTIVE_LOW>;
 	};
 
-	sound {
-		compatible = "simple-audio-card";
-		simple-audio-card,name = "mx6ul-wm8960";
-		simple-audio-card,format = "i2s";
-		simple-audio-card,bitclock-master = <&dailink_master>;
-		simple-audio-card,frame-master = <&dailink_master>;
-		simple-audio-card,widgets =
-			"Microphone", "Mic Jack",
-			"Line", "Line In",
-			"Line", "Line Out",
-			"Speaker", "Speaker",
-			"Headphone", "Headphone Jack";
-		simple-audio-card,routing =
+	sound-wm8960 {
+		compatible = "fsl,imx-audio-wm8960";
+		model = "wm8960-audio";
+		audio-cpu = <&sai2>;
+		audio-codec = <&codec>;
+		audio-asrc = <&asrc>;
+		hp-det-gpio = <&gpio5 4 0>;
+		audio-routing =
 			"Headphone Jack", "HP_L",
 			"Headphone Jack", "HP_R",
-			"Speaker", "SPK_LP",
-			"Speaker", "SPK_LN",
-			"Speaker", "SPK_RP",
-			"Speaker", "SPK_RN",
-			"LINPUT1", "Mic Jack",
+			"Ext Spk", "SPK_LP",
+			"Ext Spk", "SPK_LN",
+			"Ext Spk", "SPK_RP",
+			"Ext Spk", "SPK_RN",
+			"LINPUT2", "Mic Jack",
 			"LINPUT3", "Mic Jack",
-			"RINPUT1", "Mic Jack",
-			"RINPUT2", "Mic Jack";
-
-		simple-audio-card,cpu {
-			sound-dai = <&sai2>;
-		};
-
-		dailink_master: simple-audio-card,codec {
-			sound-dai = <&codec>;
-			clocks = <&clks IMX6UL_CLK_SAI2>;
-		};
+			"RINPUT1", "AMIC",
+			"RINPUT2", "AMIC",
+			"Mic Jack", "MICB",
+			"AMIC", "MICB";
 	};
 
 	spi4 {
@@ -145,6 +133,10 @@ codec: wm8960@1a {
 		compatible = "wlf,wm8960";
 		reg = <0x1a>;
 		wlf,shared-lrclk;
+		wlf,hp-cfg = <3 2 3>;
+		wlf,gpio-cfg = <1 3>;
+		clocks = <&clks IMX6UL_CLK_SAI2>;
+		clock-names = "mclk";
 	};
 
 	camera@3c {

arch/arm/boot/dts/imx7d-sdb.dts

@@ -164,6 +164,13 @@ sound {
 			"LINPUT1", "AMIC",
 			"AMIC", "MICB";
 	};
+
+	sound-hdmi {
+		compatible = "fsl,imx-audio-sii902x";
+		model = "sii902x-audio";
+		audio-cpu = <&sai3>;
+		hdmi-out;
+	};
 };
 
 &adc1 {