Commit 971617c3 authored by Tim Harvey's avatar Tim Harvey Committed by David S. Miller

net: thunderx: workaround BGX TX Underflow issue

While it is not yet understood why a TX underflow can easily occur
for SGMII interfaces resulting in a TX wedge. It has been found that
disabling/re-enabling the LMAC resolves the issue.
Signed-off-by: default avatarTim Harvey <tharvey@gateworks.com>
Reviewed-by: default avatarRobert Jones <rjones@gateworks.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
parent 68b759a7
......@@ -410,10 +410,19 @@ void bgx_lmac_rx_tx_enable(int node, int bgx_idx, int lmacid, bool enable)
lmac = &bgx->lmac[lmacid];
cfg = bgx_reg_read(bgx, lmacid, BGX_CMRX_CFG);
if (enable)
if (enable) {
cfg |= CMR_PKT_RX_EN | CMR_PKT_TX_EN;
else
/* enable TX FIFO Underflow interrupt */
bgx_reg_modify(bgx, lmacid, BGX_GMP_GMI_TXX_INT_ENA_W1S,
GMI_TXX_INT_UNDFLW);
} else {
cfg &= ~(CMR_PKT_RX_EN | CMR_PKT_TX_EN);
/* Disable TX FIFO Underflow interrupt */
bgx_reg_modify(bgx, lmacid, BGX_GMP_GMI_TXX_INT_ENA_W1C,
GMI_TXX_INT_UNDFLW);
}
bgx_reg_write(bgx, lmacid, BGX_CMRX_CFG, cfg);
if (bgx->is_rgx)
......@@ -1535,6 +1544,48 @@ static int bgx_init_phy(struct bgx *bgx)
return bgx_init_of_phy(bgx);
}
static irqreturn_t bgx_intr_handler(int irq, void *data)
{
struct bgx *bgx = (struct bgx *)data;
u64 status, val;
int lmac;
for (lmac = 0; lmac < bgx->lmac_count; lmac++) {
status = bgx_reg_read(bgx, lmac, BGX_GMP_GMI_TXX_INT);
if (status & GMI_TXX_INT_UNDFLW) {
pci_err(bgx->pdev, "BGX%d lmac%d UNDFLW\n",
bgx->bgx_id, lmac);
val = bgx_reg_read(bgx, lmac, BGX_CMRX_CFG);
val &= ~CMR_EN;
bgx_reg_write(bgx, lmac, BGX_CMRX_CFG, val);
val |= CMR_EN;
bgx_reg_write(bgx, lmac, BGX_CMRX_CFG, val);
}
/* clear interrupts */
bgx_reg_write(bgx, lmac, BGX_GMP_GMI_TXX_INT, status);
}
return IRQ_HANDLED;
}
static void bgx_register_intr(struct pci_dev *pdev)
{
struct bgx *bgx = pci_get_drvdata(pdev);
int ret;
ret = pci_alloc_irq_vectors(pdev, BGX_LMAC_VEC_OFFSET,
BGX_LMAC_VEC_OFFSET, PCI_IRQ_ALL_TYPES);
if (ret < 0) {
pci_err(pdev, "Req for #%d msix vectors failed\n",
BGX_LMAC_VEC_OFFSET);
return;
}
ret = pci_request_irq(pdev, GMPX_GMI_TX_INT, bgx_intr_handler, NULL,
bgx, "BGX%d", bgx->bgx_id);
if (ret)
pci_free_irq(pdev, GMPX_GMI_TX_INT, bgx);
}
static int bgx_probe(struct pci_dev *pdev, const struct pci_device_id *ent)
{
int err;
......@@ -1550,7 +1601,7 @@ static int bgx_probe(struct pci_dev *pdev, const struct pci_device_id *ent)
pci_set_drvdata(pdev, bgx);
err = pci_enable_device(pdev);
err = pcim_enable_device(pdev);
if (err) {
dev_err(dev, "Failed to enable PCI device\n");
pci_set_drvdata(pdev, NULL);
......@@ -1604,6 +1655,8 @@ static int bgx_probe(struct pci_dev *pdev, const struct pci_device_id *ent)
bgx_init_hw(bgx);
bgx_register_intr(pdev);
/* Enable all LMACs */
for (lmac = 0; lmac < bgx->lmac_count; lmac++) {
err = bgx_lmac_enable(bgx, lmac);
......@@ -1620,6 +1673,7 @@ static int bgx_probe(struct pci_dev *pdev, const struct pci_device_id *ent)
err_enable:
bgx_vnic[bgx->bgx_id] = NULL;
pci_free_irq(pdev, GMPX_GMI_TX_INT, bgx);
err_release_regions:
pci_release_regions(pdev);
err_disable_device:
......@@ -1637,6 +1691,8 @@ static void bgx_remove(struct pci_dev *pdev)
for (lmac = 0; lmac < bgx->lmac_count; lmac++)
bgx_lmac_disable(bgx, lmac);
pci_free_irq(pdev, GMPX_GMI_TX_INT, bgx);
bgx_vnic[bgx->bgx_id] = NULL;
pci_release_regions(pdev);
pci_disable_device(pdev);
......
......@@ -180,6 +180,15 @@
#define BGX_GMP_GMI_TXX_BURST 0x38228
#define BGX_GMP_GMI_TXX_MIN_PKT 0x38240
#define BGX_GMP_GMI_TXX_SGMII_CTL 0x38300
#define BGX_GMP_GMI_TXX_INT 0x38500
#define BGX_GMP_GMI_TXX_INT_W1S 0x38508
#define BGX_GMP_GMI_TXX_INT_ENA_W1C 0x38510
#define BGX_GMP_GMI_TXX_INT_ENA_W1S 0x38518
#define GMI_TXX_INT_PTP_LOST BIT_ULL(4)
#define GMI_TXX_INT_LATE_COL BIT_ULL(3)
#define GMI_TXX_INT_XSDEF BIT_ULL(2)
#define GMI_TXX_INT_XSCOL BIT_ULL(1)
#define GMI_TXX_INT_UNDFLW BIT_ULL(0)
#define BGX_MSIX_VEC_0_29_ADDR 0x400000 /* +(0..29) << 4 */
#define BGX_MSIX_VEC_0_29_CTL 0x400008
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment