net: txgbe: change LAN reset mode

The old way to do LAN reset is sending reset command to firmware. Once
firmware performs reset, it reconfigures what it needs.

In the new firmware versions, veto bit is introduced for NCSI/LLDP to
block PHY domain in LAN reset. At this point, writing register of LAN
reset directly makes the same effect as the old way. And it does not
reset MNG domain, so that veto bit does not change.

Since veto bit was never used, the old firmware is compatible with the
driver before and after this change. The new firmware needs to use with
the driver after this change if it wants to implement the new feature,
otherwise it is the same as the old firmware.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20230717021333.94181-1-jiawenwu@trustnetic.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

drivers/net/ethernet/wangxun/libwx/wx_hw.c

@@ -431,71 +431,6 @@ int wx_read_ee_hostif_buffer(struct wx *wx,
 }
 EXPORT_SYMBOL(wx_read_ee_hostif_buffer);
 
-/**
- *  wx_calculate_checksum - Calculate checksum for buffer
- *  @buffer: pointer to EEPROM
- *  @length: size of EEPROM to calculate a checksum for
- *  Calculates the checksum for some buffer on a specified length.  The
- *  checksum calculated is returned.
- **/
-static u8 wx_calculate_checksum(u8 *buffer, u32 length)
-{
-	u8 sum = 0;
-	u32 i;
-
-	if (!buffer)
-		return 0;
-
-	for (i = 0; i < length; i++)
-		sum += buffer[i];
-
-	return (u8)(0 - sum);
-}
-
-/**
- *  wx_reset_hostif - send reset cmd to fw
- *  @wx: pointer to hardware structure
- *
- *  Sends reset cmd to firmware through the manageability
- *  block.
- **/
-int wx_reset_hostif(struct wx *wx)
-{
-	struct wx_hic_reset reset_cmd;
-	int ret_val = 0;
-	int i;
-
-	reset_cmd.hdr.cmd = FW_RESET_CMD;
-	reset_cmd.hdr.buf_len = FW_RESET_LEN;
-	reset_cmd.hdr.cmd_or_resp.cmd_resv = FW_CEM_CMD_RESERVED;
-	reset_cmd.lan_id = wx->bus.func;
-	reset_cmd.reset_type = (u16)wx->reset_type;
-	reset_cmd.hdr.checksum = 0;
-	reset_cmd.hdr.checksum = wx_calculate_checksum((u8 *)&reset_cmd,
-						       (FW_CEM_HDR_LEN +
-							reset_cmd.hdr.buf_len));
-
-	for (i = 0; i <= FW_CEM_MAX_RETRIES; i++) {
-		ret_val = wx_host_interface_command(wx, (u32 *)&reset_cmd,
-						    sizeof(reset_cmd),
-						    WX_HI_COMMAND_TIMEOUT,
-						    true);
-		if (ret_val != 0)
-			continue;
-
-		if (reset_cmd.hdr.cmd_or_resp.ret_status ==
-		    FW_CEM_RESP_STATUS_SUCCESS)
-			ret_val = 0;
-		else
-			ret_val = -EFAULT;
-
-		break;
-	}
-
-	return ret_val;
-}
-EXPORT_SYMBOL(wx_reset_hostif);
-
 /**
  *  wx_init_eeprom_params - Initialize EEPROM params
  *  @wx: pointer to hardware structure

drivers/net/ethernet/wangxun/libwx/wx_hw.h

@@ -14,7 +14,6 @@ int wx_host_interface_command(struct wx *wx, u32 *buffer,
 int wx_read_ee_hostif(struct wx *wx, u16 offset, u16 *data);
 int wx_read_ee_hostif_buffer(struct wx *wx,
 			     u16 offset, u16 words, u16 *data);
-int wx_reset_hostif(struct wx *wx);
 void wx_init_eeprom_params(struct wx *wx);
 void wx_get_mac_addr(struct wx *wx, u8 *mac_addr);
 void wx_init_rx_addrs(struct wx *wx);

drivers/net/ethernet/wangxun/txgbe/txgbe_hw.c

@@ -257,16 +257,16 @@ static void txgbe_reset_misc(struct wx *wx)
 int txgbe_reset_hw(struct wx *wx)
 {
 	int status;
+	u32 val;
 
 	/* Call adapter stop to disable tx/rx and clear interrupts */
 	status = wx_stop_adapter(wx);
 	if (status != 0)
 		return status;
 
-	if (!(((wx->subsystem_device_id & WX_NCSI_MASK) == WX_NCSI_SUP) ||
-	      ((wx->subsystem_device_id & WX_WOL_MASK) == WX_WOL_SUP)))
-		wx_reset_hostif(wx);
-
+	val = WX_MIS_RST_LAN_RST(wx->bus.func);
+	wr32(wx, WX_MIS_RST, val | rd32(wx, WX_MIS_RST));
+	WX_WRITE_FLUSH(wx);
 	usleep_range(10, 100);
 
 	status = wx_check_flash_load(wx, TXGBE_SPI_ILDR_STATUS_LAN_SW_RST(wx->bus.func));