Commit 995a3bb7 authored by Nava kishore Manne's avatar Nava kishore Manne Committed by Greg Kroah-Hartman

fpga: zynqmp-fpga: Adds status interface

Adds status interface for zynqmp-fpga. It's a read only interface
which allows the user to get the Programmable Logic(PL) configuration
status.

Usage:
To read the Programmable Logic(PL) configuration status.
cat /sys/bus/platform/drivers/zynqmp_fpga_manager/firmware:zynqmp-firmware:pcap/status
Signed-off-by: default avatarNava kishore Manne <nava.kishore.manne@amd.com>
Acked-by: default avatarXu Yilun <yilun.xu@intel.com>
Link: https://lore.kernel.org/r/20230224120738.329416-3-nava.kishore.manne@amd.comSigned-off-by: default avatarGreg Kroah-Hartman <gregkh@linuxfoundation.org>
parent 8f118f61
What: /sys/bus/platform/drivers/zynqmp_fpga_manager/firmware:zynqmp-firmware:pcap/status
Date: February 2023
KernelVersion: 6.4
Contact: Nava kishore Manne <nava.kishore.manne@amd.com>
Description: (RO) Read fpga status.
Read returns a hexadecimal value that tells the current status
of the FPGA device. Each bit position in the status value is
described Below(see ug570 chapter 9).
https://docs.xilinx.com/v/u/en-US/ug570-ultrascale-configuration
====================== ==============================================
BIT(0) 0: No CRC error
1: CRC error
BIT(1) 0: Decryptor security not set
1: Decryptor security set
BIT(2) 0: MMCMs/PLLs are not locked
1: MMCMs/PLLs are locked
BIT(3) 0: DCI not matched
1: DCI matched
BIT(4) 0: Start-up sequence has not finished
1: Start-up sequence has finished
BIT(5) 0: All I/Os are placed in High-Z state
1: All I/Os behave as configured
BIT(6) 0: Flip-flops and block RAM are write disabled
1: Flip-flops and block RAM are write enabled
BIT(7) 0: GHIGH_B_STATUS asserted
1: GHIGH_B_STATUS deasserted
BIT(8) to BIT(10) Status of the mode pins
BIT(11) 0: Initialization has not finished
1: Initialization finished
BIT(12) Value on INIT_B_PIN pin
BIT(13) 0: Signal not released
1: Signal released
BIT(14) Value on DONE_PIN pin.
BIT(15) 0: No IDCODE_ERROR
1: IDCODE_ERROR
BIT(16) 0: No SECURITY_ERROR
1: SECURITY_ERROR
BIT(17) System Monitor over-temperature if set
BIT(18) to BIT(20) Start-up state machine (0 to 7)
Phase 0 = 000
Phase 1 = 001
Phase 2 = 011
Phase 3 = 010
Phase 4 = 110
Phase 5 = 111
Phase 6 = 101
Phase 7 = 100
BIT(25) to BIT(26) Indicates the detected bus width
00 = x1
01 = x8
10 = x16
11 = x32
====================== ==============================================
The other bits are reserved.
......@@ -77,6 +77,26 @@ static enum fpga_mgr_states zynqmp_fpga_ops_state(struct fpga_manager *mgr)
return FPGA_MGR_STATE_UNKNOWN;
}
static ssize_t status_show(struct device *dev,
struct device_attribute *attr, char *buf)
{
u32 status;
int ret;
ret = zynqmp_pm_fpga_get_config_status(&status);
if (ret)
return ret;
return sysfs_emit(buf, "0x%x\n", status);
}
static DEVICE_ATTR_RO(status);
static struct attribute *zynqmp_fpga_attrs[] = {
&dev_attr_status.attr,
NULL,
};
ATTRIBUTE_GROUPS(zynqmp_fpga);
static const struct fpga_manager_ops zynqmp_fpga_ops = {
.state = zynqmp_fpga_ops_state,
.write_init = zynqmp_fpga_ops_write_init,
......@@ -113,6 +133,7 @@ static struct platform_driver zynqmp_fpga_driver = {
.driver = {
.name = "zynqmp_fpga_manager",
.of_match_table = of_match_ptr(zynqmp_fpga_of_match),
.dev_groups = zynqmp_fpga_groups,
},
};
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment