ARM: dts: berlin: add I2C nodes for BG2Q

The Marvell Berlin BG2Q has 4 TWSI compatible with the Synopsys
DesignWare I2C driver. Add the corresponding nodes.

The pin-muxing setup is also done here, since there cannot be another
muxing setup if I2C{0,1,2,3} are enabled.
Signed-off-by: Antoine Ténart <antoine.tenart@free-electrons.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>

arch/arm/boot/dts/berlin2q.dtsi

@@ -193,6 +193,32 @@ portd: gpio-port@3 {
 				};
 			};
 
+			i2c0: i2c@1400 {
+				compatible = "snps,designware-i2c";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x1400 0x100>;
+				interrupt-parent = <&aic>;
+				interrupts = <4>;
+				clocks = <&chip CLKID_CFG>;
+				pinctrl-0 = <&twsi0_pmux>;
+				pinctrl-names = "default";
+				status = "disabled";
+			};
+
+			i2c1: i2c@1800 {
+				compatible = "snps,designware-i2c";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x1800 0x100>;
+				interrupt-parent = <&aic>;
+				interrupts = <5>;
+				clocks = <&chip CLKID_CFG>;
+				pinctrl-0 = <&twsi1_pmux>;
+				pinctrl-names = "default";
+				status = "disabled";
+			};
+
 			timer0: timer@2c00 {
 				compatible = "snps,dw-apb-timer";
 				reg = <0x2c00 0x14>;
@@ -303,6 +329,16 @@ chip: chip-control@ea0000 {
 			reg = <0xea0000 0x400>, <0xdd0170 0x10>;
 			clocks = <&refclk>;
 			clock-names = "refclk";
+
+			twsi0_pmux: twsi0-pmux {
+				groups = "G6";
+				function = "twsi0";
+			};
+
+			twsi1_pmux: twsi1-pmux {
+				groups = "G7";
+				function = "twsi1";
+			};
 		};
 
 		apb@fc0000 {
@@ -313,6 +349,32 @@ apb@fc0000 {
 			ranges = <0 0xfc0000 0x10000>;
 			interrupt-parent = <&sic>;
 
+			i2c2: i2c@7000 {
+				compatible = "snps,designware-i2c";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x7000 0x100>;
+				interrupt-parent = <&sic>;
+				interrupts = <6>;
+				clocks = <&refclk>;
+				pinctrl-0 = <&twsi2_pmux>;
+				pinctrl-names = "default";
+				status = "disabled";
+			};
+
+			i2c3: i2c@8000 {
+				compatible = "snps,designware-i2c";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x8000 0x100>;
+				interrupt-parent = <&sic>;
+				interrupts = <7>;
+				clocks = <&refclk>;
+				pinctrl-0 = <&twsi3_pmux>;
+				pinctrl-names = "default";
+				status = "disabled";
+			};
+
 			uart0: uart@9000 {
 				compatible = "snps,dw-apb-uart";
 				reg = <0x9000 0x100>;
@@ -350,6 +412,16 @@ uart1_pmux: uart1-pmux {
 					groups = "GSM14";
 					function = "uart1";
 				};
+
+				twsi2_pmux: twsi2-pmux {
+					groups = "GSM13";
+					function = "twsi2";
+				};
+
+				twsi3_pmux: twsi3-pmux {
+					groups = "GSM14";
+					function = "twsi3";
+				};
 			};
 
 			sic: interrupt-controller@e000 {