Commit 9b7a0c40 authored by Maxime Ripard's avatar Maxime Ripard Committed by Wolfram Sang

i2c: mux: Add dt support to i2c-mux-gpio driver

Allow the i2c-mux-gpio to be used by a device tree enabled device. The
bindings are inspired by the one found in the i2c-mux-pinctrl driver.
Signed-off-by: default avatarMaxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: default avatarStephen Warren <swarren@nvidia.com>
Acked-by: default avatarPeter Korsgaard <peter.korsgaard@barco.com>

[wsa: fixed some whitespace]
Signed-off-by: default avatarWolfram Sang <w.sang@pengutronix.de>
parent 29fb08c3
GPIO-based I2C Bus Mux
This binding describes an I2C bus multiplexer that uses GPIOs to
route the I2C signals.
+-----+ +-----+
| dev | | dev |
+------------+ +-----+ +-----+
| SoC | | |
| | /--------+--------+
| +------+ | +------+ child bus A, on GPIO value set to 0
| | I2C |-|--| Mux |
| +------+ | +--+---+ child bus B, on GPIO value set to 1
| | | \----------+--------+--------+
| +------+ | | | | |
| | GPIO |-|-----+ +-----+ +-----+ +-----+
| +------+ | | dev | | dev | | dev |
+------------+ +-----+ +-----+ +-----+
Required properties:
- compatible: i2c-mux-gpio
- i2c-parent: The phandle of the I2C bus that this multiplexer's master-side
port is connected to.
- mux-gpios: list of gpios used to control the muxer
* Standard I2C mux properties. See mux.txt in this directory.
* I2C child bus nodes. See mux.txt in this directory.
Optional properties:
- idle-state: value to set the muxer to when idle. When no value is
given, it defaults to the last value used.
For each i2c child node, an I2C child bus will be created. They will
be numbered based on their order in the device tree.
Whenever an access is made to a device on a child bus, the value set
in the revelant node's reg property will be output using the list of
GPIOs, the first in the list holding the least-significant value.
If an idle state is defined, using the idle-state (optional) property,
whenever an access is not being made to a device on a child bus, the
GPIOs will be set according to the idle value.
If an idle state is not defined, the most recently used value will be
left programmed into hardware whenever no access is being made to a
device on a child bus.
Example:
i2cmux {
compatible = "i2c-mux-gpio";
#address-cells = <1>;
#size-cells = <0>;
mux-gpios = <&gpio1 22 0 &gpio1 23 0>;
i2c-parent = <&i2c1>;
i2c@1 {
reg = <1>;
#address-cells = <1>;
#size-cells = <0>;
ssd1307: oled@3c {
compatible = "solomon,ssd1307fb-i2c";
reg = <0x3c>;
pwms = <&pwm 4 3000>;
reset-gpios = <&gpio2 7 1>;
reset-active-low;
};
};
i2c@3 {
reg = <3>;
#address-cells = <1>;
#size-cells = <0>;
pca9555: pca9555@20 {
compatible = "nxp,pca9555";
gpio-controller;
#gpio-cells = <2>;
reg = <0x20>;
};
};
};
...@@ -16,6 +16,8 @@ ...@@ -16,6 +16,8 @@
#include <linux/module.h> #include <linux/module.h>
#include <linux/slab.h> #include <linux/slab.h>
#include <linux/gpio.h> #include <linux/gpio.h>
#include <linux/of_i2c.h>
#include <linux/of_gpio.h>
struct gpiomux { struct gpiomux {
struct i2c_adapter *parent; struct i2c_adapter *parent;
...@@ -57,29 +59,110 @@ static int __devinit match_gpio_chip_by_label(struct gpio_chip *chip, ...@@ -57,29 +59,110 @@ static int __devinit match_gpio_chip_by_label(struct gpio_chip *chip,
return !strcmp(chip->label, data); return !strcmp(chip->label, data);
} }
#ifdef CONFIG_OF
static int __devinit i2c_mux_gpio_probe_dt(struct gpiomux *mux,
struct platform_device *pdev)
{
struct device_node *np = pdev->dev.of_node;
struct device_node *adapter_np, *child;
struct i2c_adapter *adapter;
unsigned *values, *gpios;
int i = 0;
if (!np)
return -ENODEV;
adapter_np = of_parse_phandle(np, "i2c-parent", 0);
if (!adapter_np) {
dev_err(&pdev->dev, "Cannot parse i2c-parent\n");
return -ENODEV;
}
adapter = of_find_i2c_adapter_by_node(adapter_np);
if (!adapter) {
dev_err(&pdev->dev, "Cannot find parent bus\n");
return -ENODEV;
}
mux->data.parent = i2c_adapter_id(adapter);
put_device(&adapter->dev);
mux->data.n_values = of_get_child_count(np);
values = devm_kzalloc(&pdev->dev,
sizeof(*mux->data.values) * mux->data.n_values,
GFP_KERNEL);
if (!values) {
dev_err(&pdev->dev, "Cannot allocate values array");
return -ENOMEM;
}
for_each_child_of_node(np, child) {
of_property_read_u32(child, "reg", values + i);
i++;
}
mux->data.values = values;
if (of_property_read_u32(np, "idle-state", &mux->data.idle))
mux->data.idle = I2C_MUX_GPIO_NO_IDLE;
mux->data.n_gpios = of_gpio_named_count(np, "mux-gpios");
if (mux->data.n_gpios < 0) {
dev_err(&pdev->dev, "Missing mux-gpios property in the DT.\n");
return -EINVAL;
}
gpios = devm_kzalloc(&pdev->dev,
sizeof(*mux->data.gpios) * mux->data.n_gpios, GFP_KERNEL);
if (!gpios) {
dev_err(&pdev->dev, "Cannot allocate gpios array");
return -ENOMEM;
}
for (i = 0; i < mux->data.n_gpios; i++)
gpios[i] = of_get_named_gpio(np, "mux-gpios", i);
mux->data.gpios = gpios;
return 0;
}
#else
static int __devinit i2c_mux_gpio_probe_dt(struct gpiomux *mux,
struct platform_device *pdev)
{
return 0;
}
#endif
static int __devinit i2c_mux_gpio_probe(struct platform_device *pdev) static int __devinit i2c_mux_gpio_probe(struct platform_device *pdev)
{ {
struct gpiomux *mux; struct gpiomux *mux;
struct i2c_mux_gpio_platform_data *pdata;
struct i2c_adapter *parent; struct i2c_adapter *parent;
int (*deselect) (struct i2c_adapter *, void *, u32); int (*deselect) (struct i2c_adapter *, void *, u32);
unsigned initial_state, gpio_base; unsigned initial_state, gpio_base;
int i, ret; int i, ret;
pdata = pdev->dev.platform_data; mux = devm_kzalloc(&pdev->dev, sizeof(*mux), GFP_KERNEL);
if (!pdata) { if (!mux) {
dev_err(&pdev->dev, "Missing platform data\n"); dev_err(&pdev->dev, "Cannot allocate gpiomux structure");
return -ENODEV; return -ENOMEM;
} }
platform_set_drvdata(pdev, mux);
if (!pdev->dev.platform_data) {
ret = i2c_mux_gpio_probe_dt(mux, pdev);
if (ret < 0)
return ret;
} else
memcpy(&mux->data, pdev->dev.platform_data, sizeof(mux->data));
/* /*
* If a GPIO chip name is provided, the GPIO pin numbers provided are * If a GPIO chip name is provided, the GPIO pin numbers provided are
* relative to its base GPIO number. Otherwise they are absolute. * relative to its base GPIO number. Otherwise they are absolute.
*/ */
if (pdata->gpio_chip) { if (mux->data.gpio_chip) {
struct gpio_chip *gpio; struct gpio_chip *gpio;
gpio = gpiochip_find(pdata->gpio_chip, gpio = gpiochip_find(mux->data.gpio_chip,
match_gpio_chip_by_label); match_gpio_chip_by_label);
if (!gpio) if (!gpio)
return -EPROBE_DEFER; return -EPROBE_DEFER;
...@@ -89,49 +172,44 @@ static int __devinit i2c_mux_gpio_probe(struct platform_device *pdev) ...@@ -89,49 +172,44 @@ static int __devinit i2c_mux_gpio_probe(struct platform_device *pdev)
gpio_base = 0; gpio_base = 0;
} }
parent = i2c_get_adapter(pdata->parent); parent = i2c_get_adapter(mux->data.parent);
if (!parent) { if (!parent) {
dev_err(&pdev->dev, "Parent adapter (%d) not found\n", dev_err(&pdev->dev, "Parent adapter (%d) not found\n",
pdata->parent); mux->data.parent);
return -ENODEV; return -ENODEV;
} }
mux = devm_kzalloc(&pdev->dev, sizeof(*mux), GFP_KERNEL);
if (!mux) {
ret = -ENOMEM;
goto alloc_failed;
}
mux->parent = parent; mux->parent = parent;
mux->data = *pdata;
mux->gpio_base = gpio_base; mux->gpio_base = gpio_base;
mux->adap = devm_kzalloc(&pdev->dev, mux->adap = devm_kzalloc(&pdev->dev,
sizeof(*mux->adap) * pdata->n_values, sizeof(*mux->adap) * mux->data.n_values,
GFP_KERNEL); GFP_KERNEL);
if (!mux->adap) { if (!mux->adap) {
dev_err(&pdev->dev, "Cannot allocate i2c_adapter structure");
ret = -ENOMEM; ret = -ENOMEM;
goto alloc_failed; goto alloc_failed;
} }
if (pdata->idle != I2C_MUX_GPIO_NO_IDLE) { if (mux->data.idle != I2C_MUX_GPIO_NO_IDLE) {
initial_state = pdata->idle; initial_state = mux->data.idle;
deselect = i2c_mux_gpio_deselect; deselect = i2c_mux_gpio_deselect;
} else { } else {
initial_state = pdata->values[0]; initial_state = mux->data.values[0];
deselect = NULL; deselect = NULL;
} }
for (i = 0; i < pdata->n_gpios; i++) { for (i = 0; i < mux->data.n_gpios; i++) {
ret = gpio_request(gpio_base + pdata->gpios[i], "i2c-mux-gpio"); ret = gpio_request(gpio_base + mux->data.gpios[i], "i2c-mux-gpio");
if (ret) if (ret)
goto err_request_gpio; goto err_request_gpio;
gpio_direction_output(gpio_base + pdata->gpios[i], gpio_direction_output(gpio_base + mux->data.gpios[i],
initial_state & (1 << i)); initial_state & (1 << i));
} }
for (i = 0; i < pdata->n_values; i++) { for (i = 0; i < mux->data.n_values; i++) {
u32 nr = pdata->base_nr ? (pdata->base_nr + i) : 0; u32 nr = mux->data.base_nr ? (mux->data.base_nr + i) : 0;
unsigned int class = pdata->classes ? pdata->classes[i] : 0; unsigned int class = mux->data.classes ? mux->data.classes[i] : 0;
mux->adap[i] = i2c_add_mux_adapter(parent, &pdev->dev, mux, nr, mux->adap[i] = i2c_add_mux_adapter(parent, &pdev->dev, mux, nr,
i, class, i, class,
...@@ -144,19 +222,17 @@ static int __devinit i2c_mux_gpio_probe(struct platform_device *pdev) ...@@ -144,19 +222,17 @@ static int __devinit i2c_mux_gpio_probe(struct platform_device *pdev)
} }
dev_info(&pdev->dev, "%d port mux on %s adapter\n", dev_info(&pdev->dev, "%d port mux on %s adapter\n",
pdata->n_values, parent->name); mux->data.n_values, parent->name);
platform_set_drvdata(pdev, mux);
return 0; return 0;
add_adapter_failed: add_adapter_failed:
for (; i > 0; i--) for (; i > 0; i--)
i2c_del_mux_adapter(mux->adap[i - 1]); i2c_del_mux_adapter(mux->adap[i - 1]);
i = pdata->n_gpios; i = mux->data.n_gpios;
err_request_gpio: err_request_gpio:
for (; i > 0; i--) for (; i > 0; i--)
gpio_free(gpio_base + pdata->gpios[i - 1]); gpio_free(gpio_base + mux->data.gpios[i - 1]);
alloc_failed: alloc_failed:
i2c_put_adapter(parent); i2c_put_adapter(parent);
...@@ -180,12 +256,19 @@ static int __devexit i2c_mux_gpio_remove(struct platform_device *pdev) ...@@ -180,12 +256,19 @@ static int __devexit i2c_mux_gpio_remove(struct platform_device *pdev)
return 0; return 0;
} }
static const struct of_device_id i2c_mux_gpio_of_match[] __devinitconst = {
{ .compatible = "i2c-mux-gpio", },
{},
};
MODULE_DEVICE_TABLE(of, i2c_mux_gpio_of_match);
static struct platform_driver i2c_mux_gpio_driver = { static struct platform_driver i2c_mux_gpio_driver = {
.probe = i2c_mux_gpio_probe, .probe = i2c_mux_gpio_probe,
.remove = __devexit_p(i2c_mux_gpio_remove), .remove = __devexit_p(i2c_mux_gpio_remove),
.driver = { .driver = {
.owner = THIS_MODULE, .owner = THIS_MODULE,
.name = "i2c-mux-gpio", .name = "i2c-mux-gpio",
.of_match_table = of_match_ptr(i2c_mux_gpio_of_match),
}, },
}; };
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment