Merge tag 'spi-v5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi

Pull spi updates from Mark Brown:
 "One small feature was added this release but the bulk of the diffstat
  and the changelog comes from the fact that several older drivers got
  some fairly hefty reworks and a couple of new drivers were added:

   - Support for detailed control of timing around chip selects from
     Sowjanya Komatineni.

   - A big set of fixes and imrovements for the Tegra114 driver from
     Sowjanya Komatineni.

   - A big simplification of the GPIO driver from Andrey Smirnov.

   - DMA support and fixes for the Freescale LPSPI driver from Clark
     Wang.

   - Fixes and optimizations for the bcm2835aux from Martin Sparl.

   - New drivers for Mediatek MT7621 (graduated from staging) and Zynq
     QSPI"

[ This is a so-called "evil merge" that additionally removes a warning
  due to an unused variable 'i' introduced by commit 1dfbf334 ("spi:
  ep93xx: Convert to use CS GPIO descriptors")     - Linus ]

* tag 'spi-v5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (127 commits)
  spi: rspi: Fix handling of QSPI code when transmit and receive
  spi: atmel-quadspi: fix crash while suspending
  spi: stm32: return the get_irq error
  spi: tegra114: fix PIO transfer
  spi: pxa2xx: fix SCR (divisor) calculation
  spi: Clear SPI_CS_HIGH flag from bad_bits for GPIO chip-select
  spi: ep93xx: Convert to use CS GPIO descriptors
  spi: AD ASoC: declare missing of table
  spi: spi-mem: zynq-qspi: Fix build error on architectures missing readsl/writesl
  spi: stm32-qspi: manage the get_irq error case
  spi/spi-bcm2835: Split transfers that exceed DLEN
  spi: expand mode support
  dt-bindings: spi: spi-mt65xx: add support for MT8516
  spi: pxa2xx: Add support for Intel Comet Lake
  spi/trace: Cap buffer contents at 64 bytes
  spi: Release spi_res after finalizing message
  spi: Remove warning in spi_split_transfers_maxsize()
  spi: Remove one needless transfer speed fall back case
  spi: sh-msiof: Document r8a77470 bindings
  spi: pxa2xx: use a module softdep for dw_dmac
  ...

Documentation/devicetree/bindings/spi/fsl-spi.txt

@@ -18,6 +18,10 @@ Optional properties:
 - gpios : specifies the gpio pins to be used for chipselects.
   The gpios will be referred to as reg = <index> in the SPI child nodes.
   If unspecified, a single SPI device without a chip select can be used.
+- fsl,spisel_boot : for the MPC8306 and MPC8309, specifies that the
+  SPISEL_BOOT signal is used as chip select for a slave device. Use
+  reg = <number of gpios> in the corresponding child node, i.e. 0 if
+  the gpios property is not present.
 
 Example:
 	spi@4c0 {

Documentation/devicetree/bindings/spi/nvidia,tegra114-spi.txt

@@ -23,6 +23,18 @@ Required properties:
 Recommended properties:
 - spi-max-frequency: Definition as per
                      Documentation/devicetree/bindings/spi/spi-bus.txt
+Optional properties:
+- nvidia,tx-clk-tap-delay: Delays the clock going out to the external device
+  with this tap value. This property is used to tune the outgoing data from
+  Tegra SPI master with respect to outgoing Tegra SPI master clock.
+  Tap values vary based on the platform design trace lengths from Tegra SPI
+  to corresponding slave devices. Valid tap values are from 0 thru 63.
+- nvidia,rx-clk-tap-delay: Delays the clock coming in from the external device
+  with this tap value. This property is used to adjust the Tegra SPI master
+  clock with respect to the data from the SPI slave device.
+  Tap values vary based on the platform design trace lengths from Tegra SPI
+  to corresponding slave devices. Valid tap values are from 0 thru 63.
+
 Example:
 
 spi@7000d600 {
@@ -38,4 +50,12 @@ spi@7000d600 {
 	reset-names = "spi";
 	dmas = <&apbdma 16>, <&apbdma 16>;
 	dma-names = "rx", "tx";
+	<spi-client>@<bus_num> {
+		...
+		...
+		nvidia,rx-clk-tap-delay = <0>;
+		nvidia,tx-clk-tap-delay = <16>;
+		...
+	};
+
 };

Documentation/devicetree/bindings/spi/sh-msiof.txt

@@ -4,6 +4,7 @@ Required properties:
 - compatible           : "renesas,msiof-r8a7743" (RZ/G1M)
 			 "renesas,msiof-r8a7744" (RZ/G1N)
 			 "renesas,msiof-r8a7745" (RZ/G1E)
+			 "renesas,msiof-r8a77470" (RZ/G1C)
 			 "renesas,msiof-r8a774a1" (RZ/G2M)
 			 "renesas,msiof-r8a774c0" (RZ/G2E)
 			 "renesas,msiof-r8a7790" (R-Car H2)

Documentation/devicetree/bindings/spi/snps,dw-apb-ssi.txt

@@ -8,9 +8,16 @@ Required properties:
 - interrupts : One interrupt, used by the controller.
 - #address-cells : <1>, as required by generic SPI binding.
 - #size-cells : <0>, also as required by generic SPI binding.
+- clocks : phandles for the clocks, see the description of clock-names below.
+   The phandle for the "ssi_clk" is required. The phandle for the "pclk" clock
+   is optional. If a single clock is specified but no clock-name, it is the
+   "ssi_clk" clock. If both clocks are listed, the "ssi_clk" must be first.
 
 Optional properties:
-- cs-gpios : Specifies the gpio pis to be used for chipselects.
+- clock-names : Contains the names of the clocks:
+    "ssi_clk", for the core clock used to generate the external SPI clock.
+    "pclk", the interface clock, required for register access.
+- cs-gpios : Specifies the gpio pins to be used for chipselects.
 - num-cs : The number of chipselects. If omitted, this will default to 4.
 - reg-io-width : The I/O register width (in bytes) implemented by this
   device.  Supported values are 2 or 4 (the default).
@@ -25,6 +32,7 @@ Example:
 		interrupts = <0 154 4>;
 		#address-cells = <1>;
 		#size-cells = <0>;
+		clocks = <&spi_m_clk>;
 		num-cs = <2>;
 		cs-gpios = <&gpio0 13 0>,
 			   <&gpio0 14 0>;

Documentation/devicetree/bindings/spi/spi-fsl-lpspi.txt

@@ -7,7 +7,11 @@ Required properties:
 - reg : address and length of the lpspi master registers
 - interrupt-parent : core interrupt controller
 - interrupts : lpspi interrupt
-- clocks : lpspi clock specifier
+- clocks : lpspi clock specifier. Its number and order need to correspond to the
+	   value in clock-names.
+- clock-names : Corresponding to per clock and ipg clock in "clocks"
+		respectively. In i.MX7ULP, it only has per clk, so use CLK_DUMMY
+		to fill the "ipg" blank.
 - spi-slave : spi slave mode support. In slave mode, add this attribute without
 	      value. In master mode, remove it.
 
@@ -18,6 +22,8 @@ lpspi2: lpspi@40290000 {
 	reg = <0x40290000 0x10000>;
 	interrupt-parent = <&intc>;
 	interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
-	clocks = <&clks IMX7ULP_CLK_LPSPI2>;
+	clocks = <&clks IMX7ULP_CLK_LPSPI2>,
+		 <&clks IMX7ULP_CLK_DUMMY>;
+	clock-names = "per", "ipg";
 	spi-slave;
 };

Documentation/devicetree/bindings/spi/spi-mt65xx.txt

@@ -10,6 +10,7 @@ Required properties:
     - mediatek,mt8135-spi: for mt8135 platforms
     - mediatek,mt8173-spi: for mt8173 platforms
     - mediatek,mt8183-spi: for mt8183 platforms
+    - "mediatek,mt8516-spi", "mediatek,mt2712-spi": for mt8516 platforms
 
 - #address-cells: should be 1.
 

Documentation/devicetree/bindings/spi/spi-mt7621.txt

+Binding for MTK SPI controller (MT7621 MIPS)
+
+Required properties:
+- compatible: Should be one of the following:
+  - "ralink,mt7621-spi": for mt7621/mt7628/mt7688 platforms
+- #address-cells: should be 1.
+- #size-cells: should be 0.
+- reg: Address and length of the register set for the device
+- resets: phandle to the reset controller asserting this device in
+          reset
+  See ../reset/reset.txt for details.
+
+Optional properties:
+- cs-gpios: see spi-bus.txt.
+
+Example:
+
+- SoC Specific Portion:
+spi0: spi@b00 {
+	compatible = "ralink,mt7621-spi";
+	reg = <0xb00 0x100>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+	resets = <&rstctrl 18>;
+	reset-names = "spi";
+};

Documentation/devicetree/bindings/spi/spi-zynq-qspi.txt

+Xilinx Zynq QSPI controller Device Tree Bindings
+-------------------------------------------------------------------
+
+Required properties:
+- compatible		: Should be "xlnx,zynq-qspi-1.0".
+- reg			: Physical base address and size of QSPI registers map.
+- interrupts		: Property with a value describing the interrupt
+			  number.
+- clock-names		: List of input clock names - "ref_clk", "pclk"
+			  (See clock bindings for details).
+- clocks		: Clock phandles (see clock bindings for details).
+
+Optional properties:
+- num-cs		: Number of chip selects used.
+
+Example:
+	qspi: spi@e000d000 {
+		compatible = "xlnx,zynq-qspi-1.0";
+		reg = <0xe000d000 0x1000>;
+		interrupt-parent = <&intc>;
+		interrupts = <0 19 4>;
+		clock-names = "ref_clk", "pclk";
+		clocks = <&clkc 10>, <&clkc 43>;
+		num-cs = <1>;
+	};

Documentation/spi/spi-summary

@@ -572,6 +572,12 @@ SPI MASTER METHODS
 	0: transfer is finished
 	1: transfer is still in progress
 
+    master->set_cs_timing(struct spi_device *spi, u8 setup_clk_cycles,
+			      u8 hold_clk_cycles, u8 inactive_clk_cycles)
+	This method allows SPI client drivers to request SPI master controller
+	for configuring device specific CS setup, hold and inactive timing
+	requirements.
+
     DEPRECATED METHODS
 
     master->transfer(struct spi_device *spi, struct spi_message *message)

arch/arm/mach-ep93xx/edb93xx.c

@@ -29,6 +29,7 @@
 #include <linux/platform_device.h>
 #include <linux/i2c.h>
 #include <linux/spi/spi.h>
+#include <linux/gpio/machine.h>
 
 #include <sound/cs4271.h>
 
@@ -105,13 +106,16 @@ static struct spi_board_info edb93xx_spi_board_info[] __initdata = {
 	},
 };
 
-static int edb93xx_spi_chipselects[] __initdata = {
-	EP93XX_GPIO_LINE_EGPIO6,
+static struct gpiod_lookup_table edb93xx_spi_cs_gpio_table = {
+	.dev_id = "ep93xx-spi.0",
+	.table = {
+		GPIO_LOOKUP("A", 6, "cs", GPIO_ACTIVE_LOW),
+		{ },
+	},
 };
 
 static struct ep93xx_spi_info edb93xx_spi_info __initdata = {
-	.chipselect	= edb93xx_spi_chipselects,
-	.num_chipselect	= ARRAY_SIZE(edb93xx_spi_chipselects),
+	/* Intentionally left blank */
 };
 
 static void __init edb93xx_register_spi(void)
@@ -123,6 +127,7 @@ static void __init edb93xx_register_spi(void)
 	else if (machine_is_edb9315a())
 		edb93xx_cs4271_data.gpio_nreset = EP93XX_GPIO_LINE_EGPIO14;
 
+	gpiod_add_lookup_table(&edb93xx_spi_cs_gpio_table);
 	ep93xx_register_spi(&edb93xx_spi_info, edb93xx_spi_board_info,
 			    ARRAY_SIZE(edb93xx_spi_board_info));
 }

arch/arm/mach-ep93xx/simone.c

@@ -77,13 +77,15 @@ static struct spi_board_info simone_spi_devices[] __initdata = {
  * low between multi-message command blocks. From v1.4, it uses a GPIO instead.
  * v1.3 parts will still work, since the signal on SFRMOUT is automatic.
  */
-static int simone_spi_chipselects[] __initdata = {
-	EP93XX_GPIO_LINE_EGPIO1,
+static struct gpiod_lookup_table simone_spi_cs_gpio_table = {
+	.dev_id = "ep93xx-spi.0",
+	.table = {
+		GPIO_LOOKUP("A", 1, "cs", GPIO_ACTIVE_LOW),
+		{ },
+	},
 };
 
 static struct ep93xx_spi_info simone_spi_info __initdata = {
-	.chipselect	= simone_spi_chipselects,
-	.num_chipselect	= ARRAY_SIZE(simone_spi_chipselects),
 	.use_dma = 1,
 };
 
@@ -113,6 +115,7 @@ static void __init simone_init_machine(void)
 	ep93xx_register_i2c(simone_i2c_board_info,
 			    ARRAY_SIZE(simone_i2c_board_info));
 	gpiod_add_lookup_table(&simone_mmc_spi_gpio_table);
+	gpiod_add_lookup_table(&simone_spi_cs_gpio_table);
 	ep93xx_register_spi(&simone_spi_info, simone_spi_devices,
 			    ARRAY_SIZE(simone_spi_devices));
 	simone_register_audio();

arch/arm/mach-ep93xx/ts72xx.c

@@ -22,6 +22,7 @@
 #include <linux/spi/mmc_spi.h>
 #include <linux/mmc/host.h>
 #include <linux/platform_data/spi-ep93xx.h>
+#include <linux/gpio/machine.h>
 
 #include <mach/gpio-ep93xx.h>
 #include <mach/hardware.h>
@@ -269,13 +270,15 @@ static struct spi_board_info bk3_spi_board_info[] __initdata = {
  * The all work is performed automatically by !SPI_FRAME (SFRM1) and
  * goes through CPLD
  */
-static int bk3_spi_chipselects[] __initdata = {
-	EP93XX_GPIO_LINE_F(3),
+static struct gpiod_lookup_table bk3_spi_cs_gpio_table = {
+	.dev_id = "ep93xx-spi.0",
+	.table = {
+		GPIO_LOOKUP("F", 3, "cs", GPIO_ACTIVE_LOW),
+		{ },
+	},
 };
 
 static struct ep93xx_spi_info bk3_spi_master __initdata = {
-	.chipselect	= bk3_spi_chipselects,
-	.num_chipselect = ARRAY_SIZE(bk3_spi_chipselects),
 	.use_dma	= 1,
 };
 
@@ -316,13 +319,17 @@ static struct spi_board_info ts72xx_spi_devices[] __initdata = {
 	},
 };
 
-static int ts72xx_spi_chipselects[] __initdata = {
-	EP93XX_GPIO_LINE_F(2),		/* DIO_17 */
+static struct gpiod_lookup_table ts72xx_spi_cs_gpio_table = {
+	.dev_id = "ep93xx-spi.0",
+	.table = {
+		/* DIO_17 */
+		GPIO_LOOKUP("F", 2, "cs", GPIO_ACTIVE_LOW),
+		{ },
+	},
 };
 
 static struct ep93xx_spi_info ts72xx_spi_info __initdata = {
-	.chipselect	= ts72xx_spi_chipselects,
-	.num_chipselect	= ARRAY_SIZE(ts72xx_spi_chipselects),
+	/* Intentionally left blank */
 };
 
 static void __init ts72xx_init_machine(void)
@@ -339,6 +346,7 @@ static void __init ts72xx_init_machine(void)
 	if (board_is_ts7300())
 		platform_device_register(&ts73xx_fpga_device);
 #endif
+	gpiod_add_lookup_table(&ts72xx_spi_cs_gpio_table);
 	ep93xx_register_spi(&ts72xx_spi_info, ts72xx_spi_devices,
 			    ARRAY_SIZE(ts72xx_spi_devices));
 }
@@ -398,6 +406,7 @@ static void __init bk3_init_machine(void)
 
 	ep93xx_register_eth(&ts72xx_eth_data, 1);
 
+	gpiod_add_lookup_table(&bk3_spi_cs_gpio_table);
 	ep93xx_register_spi(&bk3_spi_master, bk3_spi_board_info,
 			    ARRAY_SIZE(bk3_spi_board_info));
 

arch/arm/mach-ep93xx/vision_ep9307.c

@@ -245,15 +245,17 @@ static struct spi_board_info vision_spi_board_info[] __initdata = {
 	},
 };
 
-static int vision_spi_chipselects[] __initdata = {
-	EP93XX_GPIO_LINE_EGPIO6,
-	EP93XX_GPIO_LINE_EGPIO7,
-	EP93XX_GPIO_LINE_G(2),
+static struct gpiod_lookup_table vision_spi_cs_gpio_table = {
+	.dev_id = "ep93xx-spi.0",
+	.table = {
+		GPIO_LOOKUP_IDX("A", 6, "cs", 0, GPIO_ACTIVE_LOW),
+		GPIO_LOOKUP_IDX("A", 7, "cs", 1, GPIO_ACTIVE_LOW),
+		GPIO_LOOKUP_IDX("G", 2, "cs", 2, GPIO_ACTIVE_LOW),
+		{ },
+	},
 };
 
 static struct ep93xx_spi_info vision_spi_master __initdata = {
-	.chipselect	= vision_spi_chipselects,
-	.num_chipselect	= ARRAY_SIZE(vision_spi_chipselects),
 	.use_dma	= 1,
 };
 
@@ -295,6 +297,7 @@ static void __init vision_init_machine(void)
 	ep93xx_register_i2c(vision_i2c_info,
 				ARRAY_SIZE(vision_i2c_info));
 	gpiod_add_lookup_table(&vision_spi_mmc_gpio_table);
+	gpiod_add_lookup_table(&vision_spi_cs_gpio_table);
 	ep93xx_register_spi(&vision_spi_master, vision_spi_board_info,
 				ARRAY_SIZE(vision_spi_board_info));
 	vision_register_i2s();

arch/sh/boards/mach-ecovec24/setup.c

@@ -806,7 +806,6 @@ static struct spi_board_info spi_bus[] = {
 		.platform_data	= &mmc_spi_info,
 		.max_speed_hz	= 5000000,
 		.mode		= SPI_MODE_0,
-		.controller_data = (void *) GPIO_PTM4,
 	},
 };
 
@@ -838,6 +837,14 @@ static struct platform_device msiof0_device = {
 	.resource	= msiof0_resources,
 };
 
+static struct gpiod_lookup_table msiof_gpio_table = {
+	.dev_id = "spi_sh_msiof.0",
+	.table = {
+		GPIO_LOOKUP("sh7724_pfc", GPIO_PTM4, "cs", GPIO_ACTIVE_HIGH),
+		{ },
+	},
+};
+
 #endif
 
 /* FSI */
@@ -1296,12 +1303,11 @@ static int __init arch_setup(void)
 	gpio_request(GPIO_FN_MSIOF0_TXD, NULL);
 	gpio_request(GPIO_FN_MSIOF0_RXD, NULL);
 	gpio_request(GPIO_FN_MSIOF0_TSCK, NULL);
-	gpio_request(GPIO_PTM4, NULL); /* software CS control of TSYNC pin */
-	gpio_direction_output(GPIO_PTM4, 1); /* active low CS */
 	gpio_request(GPIO_PTB6, NULL); /* 3.3V power control */
 	gpio_direction_output(GPIO_PTB6, 0); /* disable power by default */
 
 	gpiod_add_lookup_table(&mmc_spi_gpio_table);
+	gpiod_add_lookup_table(&msiof_gpio_table);
 	spi_register_board_info(spi_bus, ARRAY_SIZE(spi_bus));
 #endif
 

drivers/spi/Kconfig

@@ -426,6 +426,12 @@ config SPI_MT65XX
 	  say Y or M here.If you are not sure, say N.
 	  SPI drivers for Mediatek MT65XX and MT81XX series ARM SoCs.
 
+config SPI_MT7621
+	tristate "MediaTek MT7621 SPI Controller"
+	depends on RALINK || COMPILE_TEST
+	help
+	  This selects a driver for the MediaTek MT7621 SPI Controller.
+
 config SPI_NPCM_PSPI
 	tristate "Nuvoton NPCM PSPI Controller"
 	depends on ARCH_NPCM || COMPILE_TEST
@@ -842,9 +848,17 @@ config SPI_XTENSA_XTFPGA
 	  16 bit words in SPI mode 0, automatically asserting CS on transfer
 	  start and deasserting on end.
 
+config SPI_ZYNQ_QSPI
+	tristate "Xilinx Zynq QSPI controller"
+	depends on ARCH_ZYNQ || COMPILE_TEST
+	help
+	  This enables support for the Zynq Quad SPI controller
+	  in master mode.
+	  This controller only supports SPI memory interface.
+
 config SPI_ZYNQMP_GQSPI
 	tristate "Xilinx ZynqMP GQSPI controller"
-	depends on SPI_MASTER && HAS_DMA
+	depends on (SPI_MASTER && HAS_DMA) || COMPILE_TEST
 	help
 	  Enables Xilinx GQSPI controller driver for Zynq UltraScale+ MPSoC.
 

drivers/spi/Makefile

@@ -60,6 +60,7 @@ obj-$(CONFIG_SPI_MPC512x_PSC)		+= spi-mpc512x-psc.o
 obj-$(CONFIG_SPI_MPC52xx_PSC)		+= spi-mpc52xx-psc.o
 obj-$(CONFIG_SPI_MPC52xx)		+= spi-mpc52xx.o
 obj-$(CONFIG_SPI_MT65XX)                += spi-mt65xx.o
+obj-$(CONFIG_SPI_MT7621)		+= spi-mt7621.o
 obj-$(CONFIG_SPI_MXIC)			+= spi-mxic.o
 obj-$(CONFIG_SPI_MXS)			+= spi-mxs.o
 obj-$(CONFIG_SPI_NPCM_PSPI)		+= spi-npcm-pspi.o
@@ -118,6 +119,7 @@ obj-$(CONFIG_SPI_XCOMM)		+= spi-xcomm.o
 obj-$(CONFIG_SPI_XILINX)		+= spi-xilinx.o
 obj-$(CONFIG_SPI_XLP)			+= spi-xlp.o
 obj-$(CONFIG_SPI_XTENSA_XTFPGA)		+= spi-xtensa-xtfpga.o
+obj-$(CONFIG_SPI_ZYNQ_QSPI)		+= spi-zynq-qspi.o
 obj-$(CONFIG_SPI_ZYNQMP_GQSPI)		+= spi-zynqmp-gqspi.o
 
 # SPI slave protocol handlers

drivers/spi/atmel-quadspi.c

@@ -366,7 +366,7 @@ static int atmel_qspi_exec_op(struct spi_mem *mem, const struct spi_mem_op *op)
 	return err;
 }
 
-const char *atmel_qspi_get_name(struct spi_mem *spimem)
+static const char *atmel_qspi_get_name(struct spi_mem *spimem)
 {
 	return dev_name(spimem->spi->dev.parent);
 }
@@ -570,7 +570,8 @@ static int atmel_qspi_remove(struct platform_device *pdev)
 
 static int __maybe_unused atmel_qspi_suspend(struct device *dev)
 {
-	struct atmel_qspi *aq = dev_get_drvdata(dev);
+	struct spi_controller *ctrl = dev_get_drvdata(dev);
+	struct atmel_qspi *aq = spi_controller_get_devdata(ctrl);
 
 	clk_disable_unprepare(aq->qspick);
 	clk_disable_unprepare(aq->pclk);
@@ -580,7 +581,8 @@ static int __maybe_unused atmel_qspi_suspend(struct device *dev)
 
 static int __maybe_unused atmel_qspi_resume(struct device *dev)
 {
-	struct atmel_qspi *aq = dev_get_drvdata(dev);
+	struct spi_controller *ctrl = dev_get_drvdata(dev);
+	struct atmel_qspi *aq = spi_controller_get_devdata(ctrl);
 
 	clk_prepare_enable(aq->pclk);
 	clk_prepare_enable(aq->qspick);

drivers/spi/spi-at91-usart.c

@@ -178,12 +178,6 @@ static int at91_usart_spi_setup(struct spi_device *spi)
 	struct at91_usart_spi *aus = spi_master_get_devdata(spi->controller);
 	u32 *ausd = spi->controller_state;
 	unsigned int mr = at91_usart_spi_readl(aus, MR);
-	u8 bits = spi->bits_per_word;
-
-	if (bits != 8) {
-		dev_dbg(&spi->dev, "Only 8 bits per word are supported\n");
-		return -EINVAL;
-	}
 
 	if (spi->mode & SPI_CPOL)
 		mr |= US_MR_CPOL;
@@ -212,7 +206,7 @@ static int at91_usart_spi_setup(struct spi_device *spi)
 
 	dev_dbg(&spi->dev,
 		"setup: bpw %u mode 0x%x -> mr %d %08x\n",
-		bits, spi->mode, spi->chip_select, mr);
+		spi->bits_per_word, spi->mode, spi->chip_select, mr);
 
 	return 0;
 }

drivers/spi/spi-bcm2835.c

@@ -335,20 +335,6 @@ static int bcm2835_spi_transfer_one_irq(struct spi_master *master,
 	return 1;
 }
 
-/*
- * DMA support
- *
- * this implementation has currently a few issues in so far as it does
- * not work arrount limitations of the HW.
- *
- * the main one being that DMA transfers are limited to 16 bit
- * (so 0 to 65535 bytes) by the SPI HW due to BCM2835_SPI_DLEN
- *
- * there may be a few more border-cases we may need to address as well
- * but unfortunately this would mean splitting up the scatter-gather
- * list making it slightly unpractical...
- */
-
 /**
  * bcm2835_spi_transfer_prologue() - transfer first few bytes without DMA
  * @master: SPI master
@@ -630,19 +616,6 @@ static bool bcm2835_spi_can_dma(struct spi_master *master,
 	if (tfr->len < BCM2835_SPI_DMA_MIN_LENGTH)
 		return false;
 
-	/* BCM2835_SPI_DLEN has defined a max transfer size as
-	 * 16 bit, so max is 65535
-	 * we can revisit this by using an alternative transfer
-	 * method - ideally this would get done without any more
-	 * interaction...
-	 */
-	if (tfr->len > 65535) {
-		dev_warn_once(&spi->dev,
-			      "transfer size of %d too big for dma-transfer\n",
-			      tfr->len);
-		return false;
-	}
-
 	/* return OK */
 	return true;
 }
@@ -707,7 +680,6 @@ static void bcm2835_dma_init(struct spi_master *master, struct device *dev)
 
 	/* all went well, so set can_dma */
 	master->can_dma = bcm2835_spi_can_dma;
-	master->max_dma_len = 65535; /* limitation by BCM2835_SPI_DLEN */
 	/* need to do TX AND RX DMA, so we need dummy buffers */
 	master->flags = SPI_MASTER_MUST_RX | SPI_MASTER_MUST_TX;
 
@@ -844,6 +816,17 @@ static int bcm2835_spi_prepare_message(struct spi_master *master,
 	struct spi_device *spi = msg->spi;
 	struct bcm2835_spi *bs = spi_master_get_devdata(master);
 	u32 cs = bcm2835_rd(bs, BCM2835_SPI_CS);
+	int ret;
+
+	/*
+	 * DMA transfers are limited to 16 bit (0 to 65535 bytes) by the SPI HW
+	 * due to DLEN. Split up transfers (32-bit FIFO aligned) if the limit is
+	 * exceeded.
+	 */
+	ret = spi_split_transfers_maxsize(master, msg, 65532,
+					  GFP_KERNEL | GFP_DMA);
+	if (ret)
+		return ret;
 
 	cs &= ~(BCM2835_SPI_CS_CPOL | BCM2835_SPI_CS_CPHA);
 

drivers/spi/spi-bitbang.c

@@ -335,6 +335,42 @@ static void spi_bitbang_set_cs(struct spi_device *spi, bool enable)
 
 /*----------------------------------------------------------------------*/
 
+int spi_bitbang_init(struct spi_bitbang *bitbang)
+{
+	struct spi_master *master = bitbang->master;
+
+	if (!master || !bitbang->chipselect)
+		return -EINVAL;
+
+	mutex_init(&bitbang->lock);
+
+	if (!master->mode_bits)
+		master->mode_bits = SPI_CPOL | SPI_CPHA | bitbang->flags;
+
+	if (master->transfer || master->transfer_one_message)
+		return -EINVAL;
+
+	master->prepare_transfer_hardware = spi_bitbang_prepare_hardware;
+	master->unprepare_transfer_hardware = spi_bitbang_unprepare_hardware;
+	master->transfer_one = spi_bitbang_transfer_one;
+	master->set_cs = spi_bitbang_set_cs;
+
+	if (!bitbang->txrx_bufs) {
+		bitbang->use_dma = 0;
+		bitbang->txrx_bufs = spi_bitbang_bufs;
+		if (!master->setup) {
+			if (!bitbang->setup_transfer)
+				bitbang->setup_transfer =
+					 spi_bitbang_setup_transfer;
+			master->setup = spi_bitbang_setup;
+			master->cleanup = spi_bitbang_cleanup;
+		}
+	}
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(spi_bitbang_init);
+
 /**
  * spi_bitbang_start - start up a polled/bitbanging SPI master driver
  * @bitbang: driver handle
@@ -368,33 +404,9 @@ int spi_bitbang_start(struct spi_bitbang *bitbang)
 	struct spi_master *master = bitbang->master;
 	int ret;
 
-	if (!master || !bitbang->chipselect)
-		return -EINVAL;
-
-	mutex_init(&bitbang->lock);
-
-	if (!master->mode_bits)
-		master->mode_bits = SPI_CPOL | SPI_CPHA | bitbang->flags;
-
-	if (master->transfer || master->transfer_one_message)
-		return -EINVAL;
-
-	master->prepare_transfer_hardware = spi_bitbang_prepare_hardware;
-	master->unprepare_transfer_hardware = spi_bitbang_unprepare_hardware;
-	master->transfer_one = spi_bitbang_transfer_one;
-	master->set_cs = spi_bitbang_set_cs;
-
-	if (!bitbang->txrx_bufs) {
-		bitbang->use_dma = 0;
-		bitbang->txrx_bufs = spi_bitbang_bufs;
-		if (!master->setup) {
-			if (!bitbang->setup_transfer)
-				bitbang->setup_transfer =
-					 spi_bitbang_setup_transfer;
-			master->setup = spi_bitbang_setup;
-			master->cleanup = spi_bitbang_cleanup;
-		}
-	}
+	ret = spi_bitbang_init(bitbang);
+	if (ret)
+		return ret;
 
 	/* driver may get busy before register() returns, especially
 	 * if someone registered boardinfo for devices

drivers/spi/spi-dw-mmio.c

@@ -30,6 +30,7 @@
 struct dw_spi_mmio {
 	struct dw_spi  dws;
 	struct clk     *clk;
+	struct clk     *pclk;
 	void           *priv;
 };
 
@@ -172,6 +173,14 @@ static int dw_spi_mmio_probe(struct platform_device *pdev)
 	if (ret)
 		return ret;
 
+	/* Optional clock needed to access the registers */
+	dwsmmio->pclk = devm_clk_get_optional(&pdev->dev, "pclk");
+	if (IS_ERR(dwsmmio->pclk))
+		return PTR_ERR(dwsmmio->pclk);
+	ret = clk_prepare_enable(dwsmmio->pclk);
+	if (ret)
+		goto out_clk;
+
 	dws->bus_num = pdev->id;
 
 	dws->max_freq = clk_get_rate(dwsmmio->clk);
@@ -199,6 +208,8 @@ static int dw_spi_mmio_probe(struct platform_device *pdev)
 	return 0;
 
 out:
+	clk_disable_unprepare(dwsmmio->pclk);
+out_clk:
 	clk_disable_unprepare(dwsmmio->clk);
 	return ret;
 }
@@ -208,6 +219,7 @@ static int dw_spi_mmio_remove(struct platform_device *pdev)
 	struct dw_spi_mmio *dwsmmio = platform_get_drvdata(pdev);
 
 	dw_spi_remove_host(&dwsmmio->dws);
+	clk_disable_unprepare(dwsmmio->pclk);
 	clk_disable_unprepare(dwsmmio->clk);
 
 	return 0;

drivers/spi/spi-ep93xx.c

@@ -28,7 +28,6 @@
 #include <linux/platform_device.h>
 #include <linux/sched.h>
 #include <linux/scatterlist.h>
-#include <linux/gpio.h>
 #include <linux/spi/spi.h>
 
 #include <linux/platform_data/dma-ep93xx.h>
@@ -652,7 +651,6 @@ static int ep93xx_spi_probe(struct platform_device *pdev)
 	struct resource *res;
 	int irq;
 	int error;
-	int i;
 
 	info = dev_get_platdata(&pdev->dev);
 	if (!info) {
@@ -676,6 +674,7 @@ static int ep93xx_spi_probe(struct platform_device *pdev)
 	if (!master)
 		return -ENOMEM;
 
+	master->use_gpio_descriptors = true;
 	master->prepare_transfer_hardware = ep93xx_spi_prepare_hardware;
 	master->unprepare_transfer_hardware = ep93xx_spi_unprepare_hardware;
 	master->prepare_message = ep93xx_spi_prepare_message;
@@ -683,31 +682,11 @@ static int ep93xx_spi_probe(struct platform_device *pdev)
 	master->bus_num = pdev->id;
 	master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_CS_HIGH;
 	master->bits_per_word_mask = SPI_BPW_RANGE_MASK(4, 16);
-
-	master->num_chipselect = info->num_chipselect;
-	master->cs_gpios = devm_kcalloc(&master->dev,
-					master->num_chipselect, sizeof(int),
-					GFP_KERNEL);
-	if (!master->cs_gpios) {
-		error = -ENOMEM;
-		goto fail_release_master;
-	}
-
-	for (i = 0; i < master->num_chipselect; i++) {
-		master->cs_gpios[i] = info->chipselect[i];
-
-		if (!gpio_is_valid(master->cs_gpios[i]))
-			continue;
-
-		error = devm_gpio_request_one(&pdev->dev, master->cs_gpios[i],
-					      GPIOF_OUT_INIT_HIGH,
-					      "ep93xx-spi");
-		if (error) {
-			dev_err(&pdev->dev, "could not request cs gpio %d\n",
-				master->cs_gpios[i]);
-			goto fail_release_master;
-		}
-	}
+	/*
+	 * The SPI core will count the number of GPIO descriptors to figure
+	 * out the number of chip selects available on the platform.
+	 */
+	master->num_chipselect = 0;
 
 	platform_set_drvdata(pdev, master);
 

drivers/spi/spi-fsl-lib.h

@@ -95,8 +95,10 @@ static inline u32 mpc8xxx_spi_read_reg(__be32 __iomem *reg)
 
 struct mpc8xxx_spi_probe_info {
 	struct fsl_spi_platform_data pdata;
+	int ngpios;
 	int *gpios;
 	bool *alow_flags;
+	__be32 __iomem *immr_spi_cs;
 };
 
 extern u32 mpc8xxx_spi_tx_buf_u8(struct mpc8xxx_spi *mpc8xxx_spi);

drivers/spi/spi-fsl-qspi.c

@@ -882,7 +882,7 @@ static int fsl_qspi_probe(struct platform_device *pdev)
 
 	ctlr->dev.of_node = np;
 
-	ret = spi_register_controller(ctlr);
+	ret = devm_spi_register_controller(dev, ctlr);
 	if (ret)
 		goto err_destroy_mutex;
 

drivers/spi/spi-fsl-spi.c

@@ -39,6 +39,14 @@
 #include <linux/spi/spi_bitbang.h>
 #include <linux/types.h>
 
+#ifdef CONFIG_FSL_SOC
+#include <sysdev/fsl_soc.h>
+#endif
+
+/* Specific to the MPC8306/MPC8309 */
+#define IMMR_SPI_CS_OFFSET 0x14c
+#define SPI_BOOT_SEL_BIT   0x80000000
+
 #include "spi-fsl-lib.h"
 #include "spi-fsl-cpm.h"
 #include "spi-fsl-spi.h"
@@ -355,33 +363,50 @@ static int fsl_spi_bufs(struct spi_device *spi, struct spi_transfer *t,
 static int fsl_spi_do_one_msg(struct spi_master *master,
 			      struct spi_message *m)
 {
+	struct mpc8xxx_spi *mpc8xxx_spi = spi_master_get_devdata(master);
 	struct spi_device *spi = m->spi;
 	struct spi_transfer *t, *first;
 	unsigned int cs_change;
 	const int nsecs = 50;
-	int status;
+	int status, last_bpw;
+
+	/*
+	 * In CPU mode, optimize large byte transfers to use larger
+	 * bits_per_word values to reduce number of interrupts taken.
+	 */
+	if (!(mpc8xxx_spi->flags & SPI_CPM_MODE)) {
+		list_for_each_entry(t, &m->transfers, transfer_list) {
+			if (t->len < 256 || t->bits_per_word != 8)
+				continue;
+			if ((t->len & 3) == 0)
+				t->bits_per_word = 32;
+			else if ((t->len & 1) == 0)
+				t->bits_per_word = 16;
+		}
+	}
 
 	/* Don't allow changes if CS is active */
-	first = list_first_entry(&m->transfers, struct spi_transfer,
-			transfer_list);
+	cs_change = 1;
 	list_for_each_entry(t, &m->transfers, transfer_list) {
-		if ((first->bits_per_word != t->bits_per_word) ||
-			(first->speed_hz != t->speed_hz)) {
+		if (cs_change)
+			first = t;
+		cs_change = t->cs_change;
+		if (first->speed_hz != t->speed_hz) {
 			dev_err(&spi->dev,
-				"bits_per_word/speed_hz should be same for the same SPI transfer\n");
+				"speed_hz cannot change while CS is active\n");
 			return -EINVAL;
 		}
 	}
 
+	last_bpw = -1;
 	cs_change = 1;
 	status = -EINVAL;
 	list_for_each_entry(t, &m->transfers, transfer_list) {
-		if (t->bits_per_word || t->speed_hz) {
-			if (cs_change)
-				status = fsl_spi_setup_transfer(spi, t);
-			if (status < 0)
-				break;
-		}
+		if (cs_change || last_bpw != t->bits_per_word)
+			status = fsl_spi_setup_transfer(spi, t);
+		if (status < 0)
+			break;
+		last_bpw = t->bits_per_word;
 
 		if (cs_change) {
 			fsl_spi_chipselect(spi, BITBANG_CS_ACTIVE);
@@ -701,10 +726,17 @@ static void fsl_spi_cs_control(struct spi_device *spi, bool on)
 	struct fsl_spi_platform_data *pdata = dev_get_platdata(dev);
 	struct mpc8xxx_spi_probe_info *pinfo = to_of_pinfo(pdata);
 	u16 cs = spi->chip_select;
-	int gpio = pinfo->gpios[cs];
-	bool alow = pinfo->alow_flags[cs];
 
-	gpio_set_value(gpio, on ^ alow);
+	if (cs < pinfo->ngpios) {
+		int gpio = pinfo->gpios[cs];
+		bool alow = pinfo->alow_flags[cs];
+
+		gpio_set_value(gpio, on ^ alow);
+	} else {
+		if (WARN_ON_ONCE(cs > pinfo->ngpios || !pinfo->immr_spi_cs))
+			return;
+		iowrite32be(on ? SPI_BOOT_SEL_BIT : 0, pinfo->immr_spi_cs);
+	}
 }
 
 static int of_fsl_spi_get_chipselects(struct device *dev)
@@ -712,12 +744,15 @@ static int of_fsl_spi_get_chipselects(struct device *dev)
 	struct device_node *np = dev->of_node;
 	struct fsl_spi_platform_data *pdata = dev_get_platdata(dev);
 	struct mpc8xxx_spi_probe_info *pinfo = to_of_pinfo(pdata);
+	bool spisel_boot = IS_ENABLED(CONFIG_FSL_SOC) &&
+		of_property_read_bool(np, "fsl,spisel_boot");
 	int ngpios;
 	int i = 0;
 	int ret;
 
 	ngpios = of_gpio_count(np);
-	if (ngpios <= 0) {
+	ngpios = max(ngpios, 0);
+	if (ngpios == 0 && !spisel_boot) {
 		/*
 		 * SPI w/o chip-select line. One SPI device is still permitted
 		 * though.
@@ -726,6 +761,7 @@ static int of_fsl_spi_get_chipselects(struct device *dev)
 		return 0;
 	}
 
+	pinfo->ngpios = ngpios;
 	pinfo->gpios = kmalloc_array(ngpios, sizeof(*pinfo->gpios),
 				     GFP_KERNEL);
 	if (!pinfo->gpios)
@@ -769,7 +805,18 @@ static int of_fsl_spi_get_chipselects(struct device *dev)
 		}
 	}
 
-	pdata->max_chipselect = ngpios;
+#if IS_ENABLED(CONFIG_FSL_SOC)
+	if (spisel_boot) {
+		pinfo->immr_spi_cs = ioremap(get_immrbase() + IMMR_SPI_CS_OFFSET, 4);
+		if (!pinfo->immr_spi_cs) {
+			ret = -ENOMEM;
+			i = ngpios - 1;
+			goto err_loop;
+		}
+	}
+#endif
+
+	pdata->max_chipselect = ngpios + spisel_boot;
 	pdata->cs_control = fsl_spi_cs_control;
 
 	return 0;

drivers/spi/spi-imx.c

@@ -28,6 +28,10 @@
 
 #define DRIVER_NAME "spi_imx"
 
+static bool use_dma = true;
+module_param(use_dma, bool, 0644);
+MODULE_PARM_DESC(use_dma, "Enable usage of DMA when available (default)");
+
 #define MXC_CSPIRXDATA		0x00
 #define MXC_CSPITXDATA		0x04
 #define MXC_CSPICTRL		0x08
@@ -219,6 +223,9 @@ static bool spi_imx_can_dma(struct spi_master *master, struct spi_device *spi,
 {
 	struct spi_imx_data *spi_imx = spi_master_get_devdata(master);
 
+	if (!use_dma)
+		return false;
+
 	if (!master->dma_rx)
 		return false;
 
@@ -1494,7 +1501,7 @@ static int spi_imx_transfer(struct spi_device *spi,
 
 	/* flush rxfifo before transfer */
 	while (spi_imx->devtype_data->rx_available(spi_imx))
-		spi_imx->rx(spi_imx);
+		readl(spi_imx->base + MXC_CSPIRXDATA);
 
 	if (spi_imx->slave_mode)
 		return spi_imx_pio_transfer_slave(spi, transfer);

drivers/spi/spi-mem.c

@@ -135,8 +135,8 @@ static int spi_check_buswidth_req(struct spi_mem *mem, u8 buswidth, bool tx)
 	return -ENOTSUPP;
 }
 
-static bool spi_mem_default_supports_op(struct spi_mem *mem,
-					const struct spi_mem_op *op)
+bool spi_mem_default_supports_op(struct spi_mem *mem,
+				 const struct spi_mem_op *op)
 {
 	if (spi_check_buswidth_req(mem, op->cmd.buswidth, true))
 		return false;
@@ -622,7 +622,7 @@ void devm_spi_mem_dirmap_destroy(struct device *dev,
 EXPORT_SYMBOL_GPL(devm_spi_mem_dirmap_destroy);
 
 /**
- * spi_mem_dirmap_dirmap_read() - Read data through a direct mapping
+ * spi_mem_dirmap_read() - Read data through a direct mapping
  * @desc: direct mapping descriptor
  * @offs: offset to start reading from. Note that this is not an absolute
  *	  offset, but the offset within the direct mapping which already has
@@ -668,7 +668,7 @@ ssize_t spi_mem_dirmap_read(struct spi_mem_dirmap_desc *desc,
 EXPORT_SYMBOL_GPL(spi_mem_dirmap_read);
 
 /**
- * spi_mem_dirmap_dirmap_write() - Write data through a direct mapping
+ * spi_mem_dirmap_write() - Write data through a direct mapping
  * @desc: direct mapping descriptor
  * @offs: offset to start writing from. Note that this is not an absolute
  *	  offset, but the offset within the direct mapping which already has

drivers/staging/mt7621-spi/spi-mt7621.c → drivers/spi/spi-mt7621.c

 // SPDX-License-Identifier: GPL-2.0
-/*
- * spi-mt7621.c -- MediaTek MT7621 SPI controller driver
- *
- * Copyright (C) 2011 Sergiy <piratfm@gmail.com>
- * Copyright (C) 2011-2013 Gabor Juhos <juhosg@openwrt.org>
- * Copyright (C) 2014-2015 Felix Fietkau <nbd@nbd.name>
- *
- * Some parts are based on spi-orion.c:
- *   Author: Shadi Ammouri <shadi@marvell.com>
- *   Copyright (C) 2007-2008 Marvell Ltd.
- */
+//
+// spi-mt7621.c -- MediaTek MT7621 SPI controller driver
+//
+// Copyright (C) 2011 Sergiy <piratfm@gmail.com>
+// Copyright (C) 2011-2013 Gabor Juhos <juhosg@openwrt.org>
+// Copyright (C) 2014-2015 Felix Fietkau <nbd@nbd.name>
+//
+// Some parts are based on spi-orion.c:
+//   Author: Shadi Ammouri <shadi@marvell.com>
+//   Copyright (C) 2007-2008 Marvell Ltd.
 
 #include <linux/clk.h>
 #include <linux/delay.h>
@@ -52,7 +51,7 @@
 #define MT7621_LSB_FIRST	BIT(3)
 
 struct mt7621_spi {
-	struct spi_master	*master;
+	struct spi_controller	*master;
 	void __iomem		*base;
 	unsigned int		sys_freq;
 	unsigned int		speed;
@@ -64,7 +63,7 @@ struct mt7621_spi {
 
 static inline struct mt7621_spi *spidev_to_mt7621_spi(struct spi_device *spi)
 {
-	return spi_master_get_devdata(spi->master);
+	return spi_controller_get_devdata(spi->master);
 }
 
 static inline u32 mt7621_spi_read(struct mt7621_spi *rs, u32 reg)
@@ -77,29 +76,25 @@ static inline void mt7621_spi_write(struct mt7621_spi *rs, u32 reg, u32 val)
 	iowrite32(val, rs->base + reg);
 }
 
-static void mt7621_spi_reset(struct mt7621_spi *rs)
+static void mt7621_spi_set_cs(struct spi_device *spi, int enable)
 {
-	u32 master = mt7621_spi_read(rs, MT7621_SPI_MASTER);
+	struct mt7621_spi *rs = spidev_to_mt7621_spi(spi);
+	int cs = spi->chip_select;
+	u32 polar = 0;
+	u32 master;
 
 	/*
 	 * Select SPI device 7, enable "more buffer mode" and disable
 	 * full-duplex (only half-duplex really works on this chip
 	 * reliably)
 	 */
+	master = mt7621_spi_read(rs, MT7621_SPI_MASTER);
 	master |= MASTER_RS_SLAVE_SEL | MASTER_MORE_BUFMODE;
 	master &= ~MASTER_FULL_DUPLEX;
-
 	mt7621_spi_write(rs, MT7621_SPI_MASTER, master);
-	rs->pending_write = 0;
-}
 
-static void mt7621_spi_set_cs(struct spi_device *spi, int enable)
-{
-	struct mt7621_spi *rs = spidev_to_mt7621_spi(spi);
-	int cs = spi->chip_select;
-	u32 polar = 0;
+	rs->pending_write = 0;
 
-	mt7621_spi_reset(rs);
 	if (enable)
 		polar = BIT(cs);
 	mt7621_spi_write(rs, MT7621_SPI_POLAR, polar);
@@ -163,13 +158,14 @@ static inline int mt7621_spi_wait_till_ready(struct mt7621_spi *rs)
 static void mt7621_spi_read_half_duplex(struct mt7621_spi *rs,
 					int rx_len, u8 *buf)
 {
+	int tx_len;
+
 	/*
 	 * Combine with any pending write, and perform one or more half-duplex
 	 * transactions reading 'len' bytes. Data to be written is already in
 	 * MT7621_SPI_DATA.
 	 */
-	int tx_len = rs->pending_write;
-
+	tx_len = rs->pending_write;
 	rs->pending_write = 0;
 
 	while (rx_len || tx_len) {
@@ -209,8 +205,8 @@ static inline void mt7621_spi_flush(struct mt7621_spi *rs)
 static void mt7621_spi_write_half_duplex(struct mt7621_spi *rs,
 					 int tx_len, const u8 *buf)
 {
-	int val = 0;
 	int len = rs->pending_write;
+	int val = 0;
 
 	if (len & 3) {
 		val = mt7621_spi_read(rs, MT7621_SPI_OPCODE + (len & ~3));
@@ -238,6 +234,7 @@ static void mt7621_spi_write_half_duplex(struct mt7621_spi *rs,
 		}
 		tx_len -= 1;
 	}
+
 	if (len & 3) {
 		if (len < 4) {
 			val = swab32(val);
@@ -245,13 +242,14 @@ static void mt7621_spi_write_half_duplex(struct mt7621_spi *rs,
 		}
 		mt7621_spi_write(rs, MT7621_SPI_OPCODE + (len & ~3), val);
 	}
+
 	rs->pending_write = len;
 }
 
-static int mt7621_spi_transfer_one_message(struct spi_master *master,
+static int mt7621_spi_transfer_one_message(struct spi_controller *master,
 					   struct spi_message *m)
 {
-	struct mt7621_spi *rs = spi_master_get_devdata(master);
+	struct mt7621_spi *rs = spi_controller_get_devdata(master);
 	struct spi_device *spi = m->spi;
 	unsigned int speed = spi->max_speed_hz;
 	struct spi_transfer *t = NULL;
@@ -268,11 +266,14 @@ static int mt7621_spi_transfer_one_message(struct spi_master *master,
 		goto msg_done;
 	}
 
+	/* Assert CS */
 	mt7621_spi_set_cs(spi, 1);
+
 	m->actual_length = 0;
 	list_for_each_entry(t, &m->transfers, transfer_list) {
 		if ((t->rx_buf) && (t->tx_buf)) {
-			/* This controller will shift some extra data out
+			/*
+			 * This controller will shift some extra data out
 			 * of spi_opcode if (mosi_bit_cnt > 0) &&
 			 * (cmd_bit_cnt == 0). So the claimed full-duplex
 			 * support is broken since we have no way to read
@@ -287,8 +288,9 @@ static int mt7621_spi_transfer_one_message(struct spi_master *master,
 		}
 		m->actual_length += t->len;
 	}
-	mt7621_spi_flush(rs);
 
+	/* Flush data and deassert CS */
+	mt7621_spi_flush(rs);
 	mt7621_spi_set_cs(spi, 0);
 
 msg_done:
@@ -303,7 +305,7 @@ static int mt7621_spi_setup(struct spi_device *spi)
 	struct mt7621_spi *rs = spidev_to_mt7621_spi(spi);
 
 	if ((spi->max_speed_hz == 0) ||
-		(spi->max_speed_hz > (rs->sys_freq / 2)))
+	    (spi->max_speed_hz > (rs->sys_freq / 2)))
 		spi->max_speed_hz = (rs->sys_freq / 2);
 
 	if (spi->max_speed_hz < (rs->sys_freq / 4097)) {
@@ -324,7 +326,7 @@ MODULE_DEVICE_TABLE(of, mt7621_spi_match);
 static int mt7621_spi_probe(struct platform_device *pdev)
 {
 	const struct of_device_id *match;
-	struct spi_master *master;
+	struct spi_controller *master;
 	struct mt7621_spi *rs;
 	void __iomem *base;
 	struct resource *r;
@@ -361,7 +363,7 @@ static int mt7621_spi_probe(struct platform_device *pdev)
 	}
 
 	master->mode_bits = SPI_LSB_FIRST;
-
+	master->flags = SPI_CONTROLLER_HALF_DUPLEX;
 	master->setup = mt7621_spi_setup;
 	master->transfer_one_message = mt7621_spi_transfer_one_message;
 	master->bits_per_word_mask = SPI_BPW_MASK(8);
@@ -370,7 +372,7 @@ static int mt7621_spi_probe(struct platform_device *pdev)
 
 	dev_set_drvdata(&pdev->dev, master);
 
-	rs = spi_master_get_devdata(master);
+	rs = spi_controller_get_devdata(master);
 	rs->base = base;
 	rs->clk = clk;
 	rs->master = master;
@@ -385,21 +387,18 @@ static int mt7621_spi_probe(struct platform_device *pdev)
 		return ret;
 	}
 
-	mt7621_spi_reset(rs);
-
-	return spi_register_master(master);
+	return devm_spi_register_controller(&pdev->dev, master);
 }
 
 static int mt7621_spi_remove(struct platform_device *pdev)
 {
-	struct spi_master *master;
+	struct spi_controller *master;
 	struct mt7621_spi *rs;
 
 	master = dev_get_drvdata(&pdev->dev);
-	rs = spi_master_get_devdata(master);
+	rs = spi_controller_get_devdata(master);
 
-	clk_disable(rs->clk);
-	spi_unregister_master(master);
+	clk_disable_unprepare(rs->clk);
 
 	return 0;
 }

drivers/spi/spi-mxic.c

@@ -492,8 +492,7 @@ static int mxic_spi_transfer_one(struct spi_master *master,
 
 static int __maybe_unused mxic_spi_runtime_suspend(struct device *dev)
 {
-	struct platform_device *pdev = to_platform_device(dev);
-	struct spi_master *master = platform_get_drvdata(pdev);
+	struct spi_master *master = dev_get_drvdata(dev);
 	struct mxic_spi *mxic = spi_master_get_devdata(master);
 
 	mxic_spi_clk_disable(mxic);
@@ -504,8 +503,7 @@ static int __maybe_unused mxic_spi_runtime_suspend(struct device *dev)
 
 static int __maybe_unused mxic_spi_runtime_resume(struct device *dev)
 {
-	struct platform_device *pdev = to_platform_device(dev);
-	struct spi_master *master = platform_get_drvdata(pdev);
+	struct spi_master *master = dev_get_drvdata(dev);
 	struct mxic_spi *mxic = spi_master_get_devdata(master);
 	int ret;
 

drivers/spi/spi-orion.c

@@ -470,6 +470,8 @@ orion_spi_write_read(struct spi_device *spi, struct spi_transfer *xfer)
 			if (orion_spi_write_read_8bit(spi, &tx, &rx) < 0)
 				goto out;
 			count--;
+			if (xfer->word_delay_usecs)
+				udelay(xfer->word_delay_usecs);
 		} while (count);
 	} else if (word_len == 16) {
 		const u16 *tx = xfer->tx_buf;
@@ -479,6 +481,8 @@ orion_spi_write_read(struct spi_device *spi, struct spi_transfer *xfer)
 			if (orion_spi_write_read_16bit(spi, &tx, &rx) < 0)
 				goto out;
 			count -= 2;
+			if (xfer->word_delay_usecs)
+				udelay(xfer->word_delay_usecs);
 		} while (count);
 	}
 

drivers/spi/spi-pic32.c

@@ -559,7 +559,7 @@ static int pic32_spi_one_transfer(struct spi_master *master,
 		dev_err(&spi->dev, "wait error/timedout\n");
 		if (dma_issued) {
 			dmaengine_terminate_all(master->dma_rx);
-			dmaengine_terminate_all(master->dma_rx);
+			dmaengine_terminate_all(master->dma_tx);
 		}
 		ret = -ETIMEDOUT;
 	} else {

drivers/spi/spi-pxa2xx-dma.c

@@ -239,13 +239,15 @@ int pxa2xx_spi_set_dma_burst_and_threshold(struct chip_data *chip,
 					   u32 *threshold)
 {
 	struct pxa2xx_spi_chip *chip_info = spi->controller_data;
+	struct driver_data *drv_data = spi_controller_get_devdata(spi->controller);
+	u32 dma_burst_size = drv_data->controller_info->dma_burst_size;
 
 	/*
 	 * If the DMA burst size is given in chip_info we use that,
 	 * otherwise we use the default. Also we use the default FIFO
 	 * thresholds for now.
 	 */
-	*burst_code = chip_info ? chip_info->dma_burst_size : 1;
+	*burst_code = chip_info ? chip_info->dma_burst_size : dma_burst_size;
 	*threshold = SSCR1_RxTresh(RX_THRESH_DFLT)
 		   | SSCR1_TxTresh(TX_THRESH_DFLT);
 

drivers/spi/spi-pxa2xx-pci.c

@@ -5,7 +5,6 @@
  */
 #include <linux/clk-provider.h>
 #include <linux/module.h>
-#include <linux/of_device.h>
 #include <linux/pci.h>
 #include <linux/platform_device.h>
 #include <linux/spi/pxa2xx_spi.h>
@@ -35,6 +34,8 @@ struct pxa_spi_info {
 	void *tx_param;
 	void *rx_param;
 
+	int dma_burst_size;
+
 	int (*setup)(struct pci_dev *pdev, struct pxa_spi_info *c);
 };
 
@@ -133,6 +134,7 @@ static int mrfld_spi_setup(struct pci_dev *dev, struct pxa_spi_info *c)
 	rx->dma_dev = &dma_dev->dev;
 
 	c->dma_filter = lpss_dma_filter;
+	c->dma_burst_size = 8;
 	return 0;
 }
 
@@ -223,6 +225,7 @@ static int pxa2xx_spi_pci_probe(struct pci_dev *dev,
 	spi_pdata.tx_param = c->tx_param;
 	spi_pdata.rx_param = c->rx_param;
 	spi_pdata.enable_dma = c->rx_param && c->tx_param;
+	spi_pdata.dma_burst_size = c->dma_burst_size ? c->dma_burst_size : 1;
 
 	ssp = &spi_pdata.ssp;
 	ssp->phys_base = pci_resource_start(dev, 0);

drivers/spi/spi-pxa2xx.c

@@ -884,10 +884,14 @@ static unsigned int ssp_get_clk_div(struct driver_data *drv_data, int rate)
 
 	rate = min_t(int, ssp_clk, rate);
 
+	/*
+	 * Calculate the divisor for the SCR (Serial Clock Rate), avoiding
+	 * that the SSP transmission rate can be greater than the device rate
+	 */
 	if (ssp->type == PXA25x_SSP || ssp->type == CE4100_SSP)
-		return (ssp_clk / (2 * rate) - 1) & 0xff;
+		return (DIV_ROUND_UP(ssp_clk, 2 * rate) - 1) & 0xff;
 	else
-		return (ssp_clk / rate - 1) & 0xfff;
+		return (DIV_ROUND_UP(ssp_clk, rate) - 1)  & 0xfff;
 }
 
 static unsigned int pxa2xx_ssp_get_clk_div(struct driver_data *drv_data,
@@ -925,7 +929,7 @@ static int pxa2xx_spi_transfer_one(struct spi_controller *controller,
 {
 	struct driver_data *drv_data = spi_controller_get_devdata(controller);
 	struct spi_message *message = controller->cur_msg;
-	struct chip_data *chip = spi_get_ctldata(message->spi);
+	struct chip_data *chip = spi_get_ctldata(spi);
 	u32 dma_thresh = chip->dma_threshold;
 	u32 dma_burst = chip->dma_burst_size;
 	u32 change_mask = pxa2xx_spi_get_ssrc1_change_mask(drv_data);
@@ -943,21 +947,21 @@ static int pxa2xx_spi_transfer_one(struct spi_controller *controller,
 		/* reject already-mapped transfers; PIO won't always work */
 		if (message->is_dma_mapped
 				|| transfer->rx_dma || transfer->tx_dma) {
-			dev_err(&drv_data->pdev->dev,
+			dev_err(&spi->dev,
 				"Mapped transfer length of %u is greater than %d\n",
 				transfer->len, MAX_DMA_LEN);
 			return -EINVAL;
 		}
 
 		/* warn ... we force this to PIO mode */
-		dev_warn_ratelimited(&message->spi->dev,
+		dev_warn_ratelimited(&spi->dev,
 				     "DMA disabled for transfer length %ld greater than %d\n",
 				     (long)transfer->len, MAX_DMA_LEN);
 	}
 
 	/* Setup the transfer state based on the type of transfer */
 	if (pxa2xx_spi_flush(drv_data) == 0) {
-		dev_err(&drv_data->pdev->dev, "Flush failed\n");
+		dev_err(&spi->dev, "Flush failed\n");
 		return -EIO;
 	}
 	drv_data->n_bytes = chip->n_bytes;
@@ -999,15 +1003,15 @@ static int pxa2xx_spi_transfer_one(struct spi_controller *controller,
 	 */
 	if (chip->enable_dma) {
 		if (pxa2xx_spi_set_dma_burst_and_threshold(chip,
-						message->spi,
+						spi,
 						bits, &dma_burst,
 						&dma_thresh))
-			dev_warn_ratelimited(&message->spi->dev,
+			dev_warn_ratelimited(&spi->dev,
 					     "DMA burst size reduced to match bits_per_word\n");
 	}
 
 	dma_mapped = controller->can_dma &&
-		     controller->can_dma(controller, message->spi, transfer) &&
+		     controller->can_dma(controller, spi, transfer) &&
 		     controller->cur_msg_mapped;
 	if (dma_mapped) {
 
@@ -1035,12 +1039,12 @@ static int pxa2xx_spi_transfer_one(struct spi_controller *controller,
 	/* NOTE:  PXA25x_SSP _could_ use external clocking ... */
 	cr0 = pxa2xx_configure_sscr0(drv_data, clk_div, bits);
 	if (!pxa25x_ssp_comp(drv_data))
-		dev_dbg(&message->spi->dev, "%u Hz actual, %s\n",
+		dev_dbg(&spi->dev, "%u Hz actual, %s\n",
 			controller->max_speed_hz
 				/ (1 + ((cr0 & SSCR0_SCR(0xfff)) >> 8)),
 			dma_mapped ? "DMA" : "PIO");
 	else
-		dev_dbg(&message->spi->dev, "%u Hz actual, %s\n",
+		dev_dbg(&spi->dev, "%u Hz actual, %s\n",
 			controller->max_speed_hz / 2
 				/ (1 + ((cr0 & SSCR0_SCR(0x0ff)) >> 8)),
 			dma_mapped ? "DMA" : "PIO");
@@ -1333,6 +1337,9 @@ static int setup(struct spi_device *spi)
 			dev_warn(&spi->dev,
 				 "in setup: DMA burst size reduced to match bits_per_word\n");
 		}
+		dev_dbg(&spi->dev,
+			"in setup: DMA burst size set to %u\n",
+			chip->dma_burst_size);
 	}
 
 	switch (drv_data->ssp_type) {
@@ -1451,6 +1458,10 @@ static const struct pci_device_id pxa2xx_spi_pci_compound_match[] = {
 	{ PCI_VDEVICE(INTEL, 0xa32a), LPSS_CNL_SSP },
 	{ PCI_VDEVICE(INTEL, 0xa32b), LPSS_CNL_SSP },
 	{ PCI_VDEVICE(INTEL, 0xa37b), LPSS_CNL_SSP },
+	/* CML-LP */
+	{ PCI_VDEVICE(INTEL, 0x02aa), LPSS_CNL_SSP },
+	{ PCI_VDEVICE(INTEL, 0x02ab), LPSS_CNL_SSP },
+	{ PCI_VDEVICE(INTEL, 0x02fb), LPSS_CNL_SSP },
 	{ },
 };
 
@@ -1564,6 +1575,7 @@ pxa2xx_spi_init_pdata(struct platform_device *pdev)
 	pdata->is_slave = of_property_read_bool(pdev->dev.of_node, "spi-slave");
 	pdata->num_chipselect = 1;
 	pdata->enable_dma = true;
+	pdata->dma_burst_size = 1;
 
 	return pdata;
 }
@@ -1692,7 +1704,7 @@ static int pxa2xx_spi_probe(struct platform_device *pdev)
 	if (platform_info->enable_dma) {
 		status = pxa2xx_spi_dma_setup(drv_data);
 		if (status) {
-			dev_dbg(dev, "no DMA channels available, using PIO\n");
+			dev_warn(dev, "no DMA channels available, using PIO\n");
 			platform_info->enable_dma = false;
 		} else {
 			controller->can_dma = pxa2xx_spi_can_dma;
@@ -1953,3 +1965,5 @@ static void __exit pxa2xx_spi_exit(void)
 	platform_driver_unregister(&driver);
 }
 module_exit(pxa2xx_spi_exit);
+
+MODULE_SOFTDEP("pre: dw_dmac");

drivers/spi/spi-rspi.c

@@ -271,7 +271,8 @@ static int rspi_set_config_register(struct rspi_data *rspi, int access_size)
 	/* Sets parity, interrupt mask */
 	rspi_write8(rspi, 0x00, RSPI_SPCR2);
 
-	/* Sets SPCMD */
+	/* Resets sequencer */
+	rspi_write8(rspi, 0, RSPI_SPSCR);
 	rspi->spcmd |= SPCMD_SPB_8_TO_16(access_size);
 	rspi_write16(rspi, rspi->spcmd, RSPI_SPCMD0);
 
@@ -315,7 +316,8 @@ static int rspi_rz_set_config_register(struct rspi_data *rspi, int access_size)
 	rspi_write8(rspi, 0x00, RSPI_SSLND);
 	rspi_write8(rspi, 0x00, RSPI_SPND);
 
-	/* Sets SPCMD */
+	/* Resets sequencer */
+	rspi_write8(rspi, 0, RSPI_SPSCR);
 	rspi->spcmd |= SPCMD_SPB_8_TO_16(access_size);
 	rspi_write16(rspi, rspi->spcmd, RSPI_SPCMD0);
 
@@ -366,7 +368,8 @@ static int qspi_set_config_register(struct rspi_data *rspi, int access_size)
 	/* Sets buffer to allow normal operation */
 	rspi_write8(rspi, 0x00, QSPI_SPBFCR);
 
-	/* Sets SPCMD */
+	/* Resets sequencer */
+	rspi_write8(rspi, 0, RSPI_SPSCR);
 	rspi_write16(rspi, rspi->spcmd, RSPI_SPCMD0);
 
 	/* Sets RSPI mode */
@@ -736,27 +739,22 @@ static int qspi_trigger_transfer_out_in(struct rspi_data *rspi, const u8 *tx,
 	while (len > 0) {
 		n = qspi_set_send_trigger(rspi, len);
 		qspi_set_receive_trigger(rspi, len);
-		if (n == QSPI_BUFFER_SIZE) {
-			ret = rspi_wait_for_tx_empty(rspi);
-			if (ret < 0) {
-				dev_err(&rspi->ctlr->dev, "transmit timeout\n");
-				return ret;
-			}
-			for (i = 0; i < n; i++)
-				rspi_write_data(rspi, *tx++);
+		ret = rspi_wait_for_tx_empty(rspi);
+		if (ret < 0) {
+			dev_err(&rspi->ctlr->dev, "transmit timeout\n");
+			return ret;
+		}
+		for (i = 0; i < n; i++)
+			rspi_write_data(rspi, *tx++);
 
-			ret = rspi_wait_for_rx_full(rspi);
-			if (ret < 0) {
-				dev_err(&rspi->ctlr->dev, "receive timeout\n");
-				return ret;
-			}
-			for (i = 0; i < n; i++)
-				*rx++ = rspi_read_data(rspi);
-		} else {
-			ret = rspi_pio_transfer(rspi, tx, rx, n);
-			if (ret < 0)
-				return ret;
+		ret = rspi_wait_for_rx_full(rspi);
+		if (ret < 0) {
+			dev_err(&rspi->ctlr->dev, "receive timeout\n");
+			return ret;
 		}
+		for (i = 0; i < n; i++)
+			*rx++ = rspi_read_data(rspi);
+
 		len -= n;
 	}
 
@@ -793,19 +791,14 @@ static int qspi_transfer_out(struct rspi_data *rspi, struct spi_transfer *xfer)
 
 	while (n > 0) {
 		len = qspi_set_send_trigger(rspi, n);
-		if (len == QSPI_BUFFER_SIZE) {
-			ret = rspi_wait_for_tx_empty(rspi);
-			if (ret < 0) {
-				dev_err(&rspi->ctlr->dev, "transmit timeout\n");
-				return ret;
-			}
-			for (i = 0; i < len; i++)
-				rspi_write_data(rspi, *tx++);
-		} else {
-			ret = rspi_pio_transfer(rspi, tx, NULL, len);
-			if (ret < 0)
-				return ret;
+		ret = rspi_wait_for_tx_empty(rspi);
+		if (ret < 0) {
+			dev_err(&rspi->ctlr->dev, "transmit timeout\n");
+			return ret;
 		}
+		for (i = 0; i < len; i++)
+			rspi_write_data(rspi, *tx++);
+
 		n -= len;
 	}
 
@@ -830,19 +823,14 @@ static int qspi_transfer_in(struct rspi_data *rspi, struct spi_transfer *xfer)
 
 	while (n > 0) {
 		len = qspi_set_receive_trigger(rspi, n);
-		if (len == QSPI_BUFFER_SIZE) {
-			ret = rspi_wait_for_rx_full(rspi);
-			if (ret < 0) {
-				dev_err(&rspi->ctlr->dev, "receive timeout\n");
-				return ret;
-			}
-			for (i = 0; i < len; i++)
-				*rx++ = rspi_read_data(rspi);
-		} else {
-			ret = rspi_pio_transfer(rspi, NULL, rx, len);
-			if (ret < 0)
-				return ret;
+		ret = rspi_wait_for_rx_full(rspi);
+		if (ret < 0) {
+			dev_err(&rspi->ctlr->dev, "receive timeout\n");
+			return ret;
 		}
+		for (i = 0; i < len; i++)
+			*rx++ = rspi_read_data(rspi);
+
 		n -= len;
 	}
 
@@ -868,28 +856,6 @@ static int qspi_transfer_one(struct spi_controller *ctlr,
 	}
 }
 
-static int rspi_setup(struct spi_device *spi)
-{
-	struct rspi_data *rspi = spi_controller_get_devdata(spi->controller);
-
-	rspi->max_speed_hz = spi->max_speed_hz;
-
-	rspi->spcmd = SPCMD_SSLKP;
-	if (spi->mode & SPI_CPOL)
-		rspi->spcmd |= SPCMD_CPOL;
-	if (spi->mode & SPI_CPHA)
-		rspi->spcmd |= SPCMD_CPHA;
-
-	/* CMOS output mode and MOSI signal from previous transfer */
-	rspi->sppcr = 0;
-	if (spi->mode & SPI_LOOP)
-		rspi->sppcr |= SPPCR_SPLP;
-
-	set_config_register(rspi, 8);
-
-	return 0;
-}
-
 static u16 qspi_transfer_mode(const struct spi_transfer *xfer)
 {
 	if (xfer->tx_buf)
@@ -959,8 +925,24 @@ static int rspi_prepare_message(struct spi_controller *ctlr,
 				struct spi_message *msg)
 {
 	struct rspi_data *rspi = spi_controller_get_devdata(ctlr);
+	struct spi_device *spi = msg->spi;
 	int ret;
 
+	rspi->max_speed_hz = spi->max_speed_hz;
+
+	rspi->spcmd = SPCMD_SSLKP;
+	if (spi->mode & SPI_CPOL)
+		rspi->spcmd |= SPCMD_CPOL;
+	if (spi->mode & SPI_CPHA)
+		rspi->spcmd |= SPCMD_CPHA;
+
+	/* CMOS output mode and MOSI signal from previous transfer */
+	rspi->sppcr = 0;
+	if (spi->mode & SPI_LOOP)
+		rspi->sppcr |= SPPCR_SPLP;
+
+	set_config_register(rspi, 8);
+
 	if (msg->spi->mode &
 	    (SPI_TX_DUAL | SPI_TX_QUAD | SPI_RX_DUAL | SPI_RX_QUAD)) {
 		/* Setup sequencer for messages with multiple transfer modes */
@@ -1267,7 +1249,6 @@ static int rspi_probe(struct platform_device *pdev)
 	init_waitqueue_head(&rspi->wait);
 
 	ctlr->bus_num = pdev->id;
-	ctlr->setup = rspi_setup;
 	ctlr->auto_runtime_pm = true;
 	ctlr->transfer_one = ops->transfer_one;
 	ctlr->prepare_message = rspi_prepare_message;

drivers/spi/spi-stm32-qspi.c

@@ -5,6 +5,8 @@
  */
 #include <linux/bitfield.h>
 #include <linux/clk.h>
+#include <linux/dmaengine.h>
+#include <linux/dma-mapping.h>
 #include <linux/errno.h>
 #include <linux/io.h>
 #include <linux/iopoll.h>
@@ -13,6 +15,7 @@
 #include <linux/mutex.h>
 #include <linux/of.h>
 #include <linux/of_device.h>
+#include <linux/pinctrl/consumer.h>
 #include <linux/platform_device.h>
 #include <linux/reset.h>
 #include <linux/sizes.h>
@@ -76,7 +79,6 @@
 #define QSPI_PSMAR		0x28
 #define QSPI_PIR		0x2c
 #define QSPI_LPTR		0x30
-#define LPTR_DFT_TIMEOUT	0x10
 
 #define STM32_QSPI_MAX_MMAP_SZ	SZ_256M
 #define STM32_QSPI_MAX_NORCHIP	2
@@ -84,6 +86,7 @@
 #define STM32_FIFO_TIMEOUT_US 30000
 #define STM32_BUSY_TIMEOUT_US 100000
 #define STM32_ABT_TIMEOUT_US 100000
+#define STM32_COMP_TIMEOUT_MS 1000
 
 struct stm32_qspi_flash {
 	struct stm32_qspi *qspi;
@@ -93,6 +96,8 @@ struct stm32_qspi_flash {
 
 struct stm32_qspi {
 	struct device *dev;
+	struct spi_controller *ctrl;
+	phys_addr_t phys_base;
 	void __iomem *io_base;
 	void __iomem *mm_base;
 	resource_size_t mm_size;
@@ -102,6 +107,13 @@ struct stm32_qspi {
 	struct completion data_completion;
 	u32 fmode;
 
+	struct dma_chan *dma_chtx;
+	struct dma_chan *dma_chrx;
+	struct completion dma_completion;
+
+	u32 cr_reg;
+	u32 dcr_reg;
+
 	/*
 	 * to protect device configuration, could be different between
 	 * 2 flash access (bk1, bk2)
@@ -177,6 +189,81 @@ static int stm32_qspi_tx_mm(struct stm32_qspi *qspi,
 	return 0;
 }
 
+static void stm32_qspi_dma_callback(void *arg)
+{
+	struct completion *dma_completion = arg;
+
+	complete(dma_completion);
+}
+
+static int stm32_qspi_tx_dma(struct stm32_qspi *qspi,
+			     const struct spi_mem_op *op)
+{
+	struct dma_async_tx_descriptor *desc;
+	enum dma_transfer_direction dma_dir;
+	struct dma_chan *dma_ch;
+	struct sg_table sgt;
+	dma_cookie_t cookie;
+	u32 cr, t_out;
+	int err;
+
+	if (op->data.dir == SPI_MEM_DATA_IN) {
+		dma_dir = DMA_DEV_TO_MEM;
+		dma_ch = qspi->dma_chrx;
+	} else {
+		dma_dir = DMA_MEM_TO_DEV;
+		dma_ch = qspi->dma_chtx;
+	}
+
+	/*
+	 * spi_map_buf return -EINVAL if the buffer is not DMA-able
+	 * (DMA-able: in vmalloc | kmap | virt_addr_valid)
+	 */
+	err = spi_controller_dma_map_mem_op_data(qspi->ctrl, op, &sgt);
+	if (err)
+		return err;
+
+	desc = dmaengine_prep_slave_sg(dma_ch, sgt.sgl, sgt.nents,
+				       dma_dir, DMA_PREP_INTERRUPT);
+	if (!desc) {
+		err = -ENOMEM;
+		goto out_unmap;
+	}
+
+	cr = readl_relaxed(qspi->io_base + QSPI_CR);
+
+	reinit_completion(&qspi->dma_completion);
+	desc->callback = stm32_qspi_dma_callback;
+	desc->callback_param = &qspi->dma_completion;
+	cookie = dmaengine_submit(desc);
+	err = dma_submit_error(cookie);
+	if (err)
+		goto out;
+
+	dma_async_issue_pending(dma_ch);
+
+	writel_relaxed(cr | CR_DMAEN, qspi->io_base + QSPI_CR);
+
+	t_out = sgt.nents * STM32_COMP_TIMEOUT_MS;
+	if (!wait_for_completion_interruptible_timeout(&qspi->dma_completion,
+						       msecs_to_jiffies(t_out)))
+		err = -ETIMEDOUT;
+
+	if (dma_async_is_tx_complete(dma_ch, cookie,
+				     NULL, NULL) != DMA_COMPLETE)
+		err = -ETIMEDOUT;
+
+	if (err)
+		dmaengine_terminate_all(dma_ch);
+
+out:
+	writel_relaxed(cr & ~CR_DMAEN, qspi->io_base + QSPI_CR);
+out_unmap:
+	spi_controller_dma_unmap_mem_op_data(qspi->ctrl, op, &sgt);
+
+	return err;
+}
+
 static int stm32_qspi_tx(struct stm32_qspi *qspi, const struct spi_mem_op *op)
 {
 	if (!op->data.nbytes)
@@ -184,6 +271,10 @@ static int stm32_qspi_tx(struct stm32_qspi *qspi, const struct spi_mem_op *op)
 
 	if (qspi->fmode == CCR_FMODE_MM)
 		return stm32_qspi_tx_mm(qspi, op);
+	else if ((op->data.dir == SPI_MEM_DATA_IN && qspi->dma_chrx) ||
+		 (op->data.dir == SPI_MEM_DATA_OUT && qspi->dma_chtx))
+		if (!stm32_qspi_tx_dma(qspi, op))
+			return 0;
 
 	return stm32_qspi_tx_poll(qspi, op);
 }
@@ -214,7 +305,7 @@ static int stm32_qspi_wait_cmd(struct stm32_qspi *qspi,
 	writel_relaxed(cr | CR_TCIE | CR_TEIE, qspi->io_base + QSPI_CR);
 
 	if (!wait_for_completion_interruptible_timeout(&qspi->data_completion,
-						msecs_to_jiffies(1000))) {
+				msecs_to_jiffies(STM32_COMP_TIMEOUT_MS))) {
 		err = -ETIMEDOUT;
 	} else {
 		sr = readl_relaxed(qspi->io_base + QSPI_SR);
@@ -356,7 +447,7 @@ static int stm32_qspi_setup(struct spi_device *spi)
 	struct spi_controller *ctrl = spi->master;
 	struct stm32_qspi *qspi = spi_controller_get_devdata(ctrl);
 	struct stm32_qspi_flash *flash;
-	u32 cr, presc;
+	u32 presc;
 
 	if (ctrl->busy)
 		return -EBUSY;
@@ -372,17 +463,60 @@ static int stm32_qspi_setup(struct spi_device *spi)
 	flash->presc = presc;
 
 	mutex_lock(&qspi->lock);
-	writel_relaxed(LPTR_DFT_TIMEOUT, qspi->io_base + QSPI_LPTR);
-	cr = FIELD_PREP(CR_FTHRES_MASK, 3) | CR_TCEN | CR_SSHIFT | CR_EN;
-	writel_relaxed(cr, qspi->io_base + QSPI_CR);
+	qspi->cr_reg = FIELD_PREP(CR_FTHRES_MASK, 3) | CR_SSHIFT | CR_EN;
+	writel_relaxed(qspi->cr_reg, qspi->io_base + QSPI_CR);
 
 	/* set dcr fsize to max address */
-	writel_relaxed(DCR_FSIZE_MASK, qspi->io_base + QSPI_DCR);
+	qspi->dcr_reg = DCR_FSIZE_MASK;
+	writel_relaxed(qspi->dcr_reg, qspi->io_base + QSPI_DCR);
 	mutex_unlock(&qspi->lock);
 
 	return 0;
 }
 
+static void stm32_qspi_dma_setup(struct stm32_qspi *qspi)
+{
+	struct dma_slave_config dma_cfg;
+	struct device *dev = qspi->dev;
+
+	memset(&dma_cfg, 0, sizeof(dma_cfg));
+
+	dma_cfg.src_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE;
+	dma_cfg.dst_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE;
+	dma_cfg.src_addr = qspi->phys_base + QSPI_DR;
+	dma_cfg.dst_addr = qspi->phys_base + QSPI_DR;
+	dma_cfg.src_maxburst = 4;
+	dma_cfg.dst_maxburst = 4;
+
+	qspi->dma_chrx = dma_request_slave_channel(dev, "rx");
+	if (qspi->dma_chrx) {
+		if (dmaengine_slave_config(qspi->dma_chrx, &dma_cfg)) {
+			dev_err(dev, "dma rx config failed\n");
+			dma_release_channel(qspi->dma_chrx);
+			qspi->dma_chrx = NULL;
+		}
+	}
+
+	qspi->dma_chtx = dma_request_slave_channel(dev, "tx");
+	if (qspi->dma_chtx) {
+		if (dmaengine_slave_config(qspi->dma_chtx, &dma_cfg)) {
+			dev_err(dev, "dma tx config failed\n");
+			dma_release_channel(qspi->dma_chtx);
+			qspi->dma_chtx = NULL;
+		}
+	}
+
+	init_completion(&qspi->dma_completion);
+}
+
+static void stm32_qspi_dma_free(struct stm32_qspi *qspi)
+{
+	if (qspi->dma_chtx)
+		dma_release_channel(qspi->dma_chtx);
+	if (qspi->dma_chrx)
+		dma_release_channel(qspi->dma_chrx);
+}
+
 /*
  * no special host constraint, so use default spi_mem_default_supports_op
  * to check supported mode.
@@ -395,8 +529,10 @@ static void stm32_qspi_release(struct stm32_qspi *qspi)
 {
 	/* disable qspi */
 	writel_relaxed(0, qspi->io_base + QSPI_CR);
+	stm32_qspi_dma_free(qspi);
 	mutex_destroy(&qspi->lock);
 	clk_disable_unprepare(qspi->clk);
+	spi_master_put(qspi->ctrl);
 }
 
 static int stm32_qspi_probe(struct platform_device *pdev)
@@ -413,43 +549,62 @@ static int stm32_qspi_probe(struct platform_device *pdev)
 		return -ENOMEM;
 
 	qspi = spi_controller_get_devdata(ctrl);
+	qspi->ctrl = ctrl;
 
 	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "qspi");
 	qspi->io_base = devm_ioremap_resource(dev, res);
-	if (IS_ERR(qspi->io_base))
-		return PTR_ERR(qspi->io_base);
+	if (IS_ERR(qspi->io_base)) {
+		ret = PTR_ERR(qspi->io_base);
+		goto err;
+	}
+
+	qspi->phys_base = res->start;
 
 	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "qspi_mm");
 	qspi->mm_base = devm_ioremap_resource(dev, res);
-	if (IS_ERR(qspi->mm_base))
-		return PTR_ERR(qspi->mm_base);
+	if (IS_ERR(qspi->mm_base)) {
+		ret = PTR_ERR(qspi->mm_base);
+		goto err;
+	}
 
 	qspi->mm_size = resource_size(res);
-	if (qspi->mm_size > STM32_QSPI_MAX_MMAP_SZ)
-		return -EINVAL;
+	if (qspi->mm_size > STM32_QSPI_MAX_MMAP_SZ) {
+		ret = -EINVAL;
+		goto err;
+	}
 
 	irq = platform_get_irq(pdev, 0);
+	if (irq < 0) {
+		if (irq != -EPROBE_DEFER)
+			dev_err(dev, "IRQ error missing or invalid\n");
+		return irq;
+	}
+
 	ret = devm_request_irq(dev, irq, stm32_qspi_irq, 0,
 			       dev_name(dev), qspi);
 	if (ret) {
 		dev_err(dev, "failed to request irq\n");
-		return ret;
+		goto err;
 	}
 
 	init_completion(&qspi->data_completion);
 
 	qspi->clk = devm_clk_get(dev, NULL);
-	if (IS_ERR(qspi->clk))
-		return PTR_ERR(qspi->clk);
+	if (IS_ERR(qspi->clk)) {
+		ret = PTR_ERR(qspi->clk);
+		goto err;
+	}
 
 	qspi->clk_rate = clk_get_rate(qspi->clk);
-	if (!qspi->clk_rate)
-		return -EINVAL;
+	if (!qspi->clk_rate) {
+		ret = -EINVAL;
+		goto err;
+	}
 
 	ret = clk_prepare_enable(qspi->clk);
 	if (ret) {
 		dev_err(dev, "can not enable the clock\n");
-		return ret;
+		goto err;
 	}
 
 	rstc = devm_reset_control_get_exclusive(dev, NULL);
@@ -461,6 +616,7 @@ static int stm32_qspi_probe(struct platform_device *pdev)
 
 	qspi->dev = dev;
 	platform_set_drvdata(pdev, qspi);
+	stm32_qspi_dma_setup(qspi);
 	mutex_init(&qspi->lock);
 
 	ctrl->mode_bits = SPI_RX_DUAL | SPI_RX_QUAD
@@ -472,14 +628,11 @@ static int stm32_qspi_probe(struct platform_device *pdev)
 	ctrl->dev.of_node = dev->of_node;
 
 	ret = devm_spi_register_master(dev, ctrl);
-	if (ret)
-		goto err_spi_register;
-
-	return 0;
+	if (!ret)
+		return 0;
 
-err_spi_register:
+err:
 	stm32_qspi_release(qspi);
-
 	return ret;
 }
 
@@ -491,6 +644,31 @@ static int stm32_qspi_remove(struct platform_device *pdev)
 	return 0;
 }
 
+static int __maybe_unused stm32_qspi_suspend(struct device *dev)
+{
+	struct stm32_qspi *qspi = dev_get_drvdata(dev);
+
+	clk_disable_unprepare(qspi->clk);
+	pinctrl_pm_select_sleep_state(dev);
+
+	return 0;
+}
+
+static int __maybe_unused stm32_qspi_resume(struct device *dev)
+{
+	struct stm32_qspi *qspi = dev_get_drvdata(dev);
+
+	pinctrl_pm_select_default_state(dev);
+	clk_prepare_enable(qspi->clk);
+
+	writel_relaxed(qspi->cr_reg, qspi->io_base + QSPI_CR);
+	writel_relaxed(qspi->dcr_reg, qspi->io_base + QSPI_DCR);
+
+	return 0;
+}
+
+static SIMPLE_DEV_PM_OPS(stm32_qspi_pm_ops, stm32_qspi_suspend, stm32_qspi_resume);
+
 static const struct of_device_id stm32_qspi_match[] = {
 	{.compatible = "st,stm32f469-qspi"},
 	{}
@@ -503,6 +681,7 @@ static struct platform_driver stm32_qspi_driver = {
 	.driver	= {
 		.name = "stm32-qspi",
 		.of_match_table = stm32_qspi_match,
+		.pm = &stm32_qspi_pm_ops,
 	},
 };
 module_platform_driver(stm32_qspi_driver);

drivers/spi/spi-stm32.c

@@ -1839,8 +1839,9 @@ static int stm32_spi_probe(struct platform_device *pdev)
 
 	spi->irq = platform_get_irq(pdev, 0);
 	if (spi->irq <= 0) {
-		dev_err(&pdev->dev, "no irq: %d\n", spi->irq);
-		ret = -ENOENT;
+		ret = spi->irq;
+		if (ret != -EPROBE_DEFER)
+			dev_err(&pdev->dev, "failed to get irq: %d\n", ret);
 		goto err_master_put;
 	}
 	ret = devm_request_threaded_irq(&pdev->dev, spi->irq,

drivers/spi/spi-tegra20-slink.c

@@ -717,9 +717,6 @@ static int tegra_slink_start_transfer_one(struct spi_device *spi,
 	command2 = tspi->command2_reg;
 	command2 &= ~(SLINK_RXEN | SLINK_TXEN);
 
-	tegra_slink_writel(tspi, command, SLINK_COMMAND);
-	tspi->command_reg = command;
-
 	tspi->cur_direction = 0;
 	if (t->rx_buf) {
 		command2 |= SLINK_RXEN;
@@ -729,9 +726,18 @@ static int tegra_slink_start_transfer_one(struct spi_device *spi,
 		command2 |= SLINK_TXEN;
 		tspi->cur_direction |= DATA_DIR_TX;
 	}
+
+	/*
+	 * Writing to the command2 register bevore the command register prevents
+	 * a spike in chip_select line 0. This selects the chip_select line
+	 * before changing the chip_select value.
+	 */
 	tegra_slink_writel(tspi, command2, SLINK_COMMAND2);
 	tspi->command2_reg = command2;
 
+	tegra_slink_writel(tspi, command, SLINK_COMMAND);
+	tspi->command_reg = command;
+
 	if (total_fifo_words > SLINK_FIFO_DEPTH)
 		ret = tegra_slink_start_dma_based_transfer(tspi, t);
 	else

drivers/spi/spi-topcliff-pch.c

@@ -1299,18 +1299,27 @@ static void pch_free_dma_buf(struct pch_spi_board_data *board_dat,
 				  dma->rx_buf_virt, dma->rx_buf_dma);
 }
 
-static void pch_alloc_dma_buf(struct pch_spi_board_data *board_dat,
+static int pch_alloc_dma_buf(struct pch_spi_board_data *board_dat,
 			      struct pch_spi_data *data)
 {
 	struct pch_spi_dma_ctrl *dma;
+	int ret;
 
 	dma = &data->dma;
+	ret = 0;
 	/* Get Consistent memory for Tx DMA */
 	dma->tx_buf_virt = dma_alloc_coherent(&board_dat->pdev->dev,
 				PCH_BUF_SIZE, &dma->tx_buf_dma, GFP_KERNEL);
+	if (!dma->tx_buf_virt)
+		ret = -ENOMEM;
+
 	/* Get Consistent memory for Rx DMA */
 	dma->rx_buf_virt = dma_alloc_coherent(&board_dat->pdev->dev,
 				PCH_BUF_SIZE, &dma->rx_buf_dma, GFP_KERNEL);
+	if (!dma->rx_buf_virt)
+		ret = -ENOMEM;
+
+	return ret;
 }
 
 static int pch_spi_pd_probe(struct platform_device *plat_dev)
@@ -1387,7 +1396,9 @@ static int pch_spi_pd_probe(struct platform_device *plat_dev)
 
 	if (use_dma) {
 		dev_info(&plat_dev->dev, "Use DMA for data transfers\n");
-		pch_alloc_dma_buf(board_dat, data);
+		ret = pch_alloc_dma_buf(board_dat, data);
+		if (ret)
+			goto err_spi_register_master;
 	}
 
 	ret = spi_register_master(master);

drivers/spi/spi.c

@@ -36,6 +36,8 @@
 
 #define CREATE_TRACE_POINTS
 #include <trace/events/spi.h>
+EXPORT_TRACEPOINT_SYMBOL(spi_transfer_start);
+EXPORT_TRACEPOINT_SYMBOL(spi_transfer_stop);
 
 #include "internals.h"
 
@@ -1039,6 +1041,8 @@ static int spi_map_msg(struct spi_controller *ctlr, struct spi_message *msg)
 		if (max_tx || max_rx) {
 			list_for_each_entry(xfer, &msg->transfers,
 					    transfer_list) {
+				if (!xfer->len)
+					continue;
 				if (!xfer->tx_buf)
 					xfer->tx_buf = ctlr->dummy_tx;
 				if (!xfer->rx_buf)
@@ -1177,10 +1181,10 @@ static int spi_transfer_one_message(struct spi_controller *ctlr,
 	if (msg->status && ctlr->handle_err)
 		ctlr->handle_err(ctlr, msg);
 
-	spi_res_release(ctlr, msg);
-
 	spi_finalize_current_message(ctlr);
 
+	spi_res_release(ctlr, msg);
+
 	return ret;
 }
 
@@ -2195,6 +2199,8 @@ static int spi_get_gpio_descs(struct spi_controller *ctlr)
 		 */
 		cs[i] = devm_gpiod_get_index_optional(dev, "cs", i,
 						      GPIOD_OUT_LOW);
+		if (IS_ERR(cs[i]))
+			return PTR_ERR(cs[i]);
 
 		if (cs[i]) {
 			/*
@@ -2261,7 +2267,7 @@ int spi_register_controller(struct spi_controller *ctlr)
 {
 	struct device		*dev = ctlr->dev.parent;
 	struct boardinfo	*bi;
-	int			status = -ENODEV;
+	int			status;
 	int			id, first_dynamic;
 
 	if (!dev)
@@ -2275,24 +2281,6 @@ int spi_register_controller(struct spi_controller *ctlr)
 	if (status)
 		return status;
 
-	if (!spi_controller_is_slave(ctlr)) {
-		if (ctlr->use_gpio_descriptors) {
-			status = spi_get_gpio_descs(ctlr);
-			if (status)
-				return status;
-			/*
-			 * A controller using GPIO descriptors always
-			 * supports SPI_CS_HIGH if need be.
-			 */
-			ctlr->mode_bits |= SPI_CS_HIGH;
-		} else {
-			/* Legacy code path for GPIOs from DT */
-			status = of_spi_register_master(ctlr);
-			if (status)
-				return status;
-		}
-	}
-
 	/* even if it's just one always-selected device, there must
 	 * be at least one chipselect
 	 */
@@ -2349,6 +2337,25 @@ int spi_register_controller(struct spi_controller *ctlr)
 	 * registration fails if the bus ID is in use.
 	 */
 	dev_set_name(&ctlr->dev, "spi%u", ctlr->bus_num);
+
+	if (!spi_controller_is_slave(ctlr)) {
+		if (ctlr->use_gpio_descriptors) {
+			status = spi_get_gpio_descs(ctlr);
+			if (status)
+				return status;
+			/*
+			 * A controller using GPIO descriptors always
+			 * supports SPI_CS_HIGH if need be.
+			 */
+			ctlr->mode_bits |= SPI_CS_HIGH;
+		} else {
+			/* Legacy code path for GPIOs from DT */
+			status = of_spi_register_master(ctlr);
+			if (status)
+				return status;
+		}
+	}
+
 	status = device_add(&ctlr->dev);
 	if (status < 0) {
 		/* free bus id */
@@ -2781,11 +2788,6 @@ static int __spi_split_transfer_maxsize(struct spi_controller *ctlr,
 	size_t offset;
 	size_t count, i;
 
-	/* warn once about this fact that we are splitting a transfer */
-	dev_warn_once(&msg->spi->dev,
-		      "spi_transfer of length %i exceed max length of %zu - needed to split transfers\n",
-		      xfer->len, maxsize);
-
 	/* calculate how many we have to replace */
 	count = DIV_ROUND_UP(xfer->len, maxsize);
 
@@ -2943,6 +2945,11 @@ int spi_setup(struct spi_device *spi)
 	 * so it is ignored here.
 	 */
 	bad_bits = spi->mode & ~(spi->controller->mode_bits | SPI_CS_WORD);
+	/* nothing prevents from working with active-high CS in case if it
+	 * is driven by GPIO.
+	 */
+	if (gpio_is_valid(spi->cs_gpio))
+		bad_bits &= ~SPI_CS_HIGH;
 	ugly_bits = bad_bits &
 		    (SPI_TX_DUAL | SPI_TX_QUAD | SPI_TX_OCTAL |
 		     SPI_RX_DUAL | SPI_RX_QUAD | SPI_RX_OCTAL);
@@ -2988,6 +2995,21 @@ int spi_setup(struct spi_device *spi)
 }
 EXPORT_SYMBOL_GPL(spi_setup);
 
+/**
+ * spi_set_cs_timing - configure CS setup, hold, and inactive delays
+ * @spi: the device that requires specific CS timing configuration
+ * @setup: CS setup time in terms of clock count
+ * @hold: CS hold time in terms of clock count
+ * @inactive_dly: CS inactive delay between transfers in terms of clock count
+ */
+void spi_set_cs_timing(struct spi_device *spi, u8 setup, u8 hold,
+		       u8 inactive_dly)
+{
+	if (spi->controller->set_cs_timing)
+		spi->controller->set_cs_timing(spi, setup, hold, inactive_dly);
+}
+EXPORT_SYMBOL_GPL(spi_set_cs_timing);
+
 static int __spi_validate(struct spi_device *spi, struct spi_message *message)
 {
 	struct spi_controller *ctlr = spi->controller;
@@ -3062,8 +3084,6 @@ static int __spi_validate(struct spi_device *spi, struct spi_message *message)
 
 		if (!xfer->speed_hz)
 			xfer->speed_hz = spi->max_speed_hz;
-		if (!xfer->speed_hz)
-			xfer->speed_hz = ctlr->max_speed_hz;
 
 		if (ctlr->max_speed_hz && xfer->speed_hz > ctlr->max_speed_hz)
 			xfer->speed_hz = ctlr->max_speed_hz;

drivers/spi/spidev.c

@@ -276,17 +276,19 @@ static int spidev_message(struct spidev_data *spidev,
 		k_tmp->bits_per_word = u_tmp->bits_per_word;
 		k_tmp->delay_usecs = u_tmp->delay_usecs;
 		k_tmp->speed_hz = u_tmp->speed_hz;
+		k_tmp->word_delay_usecs = u_tmp->word_delay_usecs;
 		if (!k_tmp->speed_hz)
 			k_tmp->speed_hz = spidev->speed_hz;
 #ifdef VERBOSE
 		dev_dbg(&spidev->spi->dev,
-			"  xfer len %u %s%s%s%dbits %u usec %uHz\n",
+			"  xfer len %u %s%s%s%dbits %u usec %u usec %uHz\n",
 			u_tmp->len,
 			u_tmp->rx_buf ? "rx " : "",
 			u_tmp->tx_buf ? "tx " : "",
 			u_tmp->cs_change ? "cs " : "",
 			u_tmp->bits_per_word ? : spidev->spi->bits_per_word,
 			u_tmp->delay_usecs,
+			u_tmp->word_delay_usecs,
 			u_tmp->speed_hz ? : spidev->spi->max_speed_hz);
 #endif
 		spi_message_add_tail(k_tmp, &msg);

drivers/staging/Kconfig

@@ -106,8 +106,6 @@ source "drivers/staging/mt7621-pci-phy/Kconfig"
 
 source "drivers/staging/mt7621-pinctrl/Kconfig"
 
-source "drivers/staging/mt7621-spi/Kconfig"
-
 source "drivers/staging/mt7621-dma/Kconfig"
 
 source "drivers/staging/ralink-gdma/Kconfig"

drivers/staging/Makefile

@@ -43,7 +43,6 @@ obj-$(CONFIG_PI433)		+= pi433/
 obj-$(CONFIG_PCI_MT7621)	+= mt7621-pci/
 obj-$(CONFIG_PCI_MT7621_PHY)	+= mt7621-pci-phy/
 obj-$(CONFIG_PINCTRL_RT2880)	+= mt7621-pinctrl/
-obj-$(CONFIG_SPI_MT7621)	+= mt7621-spi/
 obj-$(CONFIG_SOC_MT7621)	+= mt7621-dma/
 obj-$(CONFIG_DMA_RALINK)	+= ralink-gdma/
 obj-$(CONFIG_MTK_MMC)		+= mt7621-mmc/

drivers/staging/mt7621-spi/Kconfig

-config SPI_MT7621
-	tristate "MediaTek MT7621 SPI Controller"
-	depends on RALINK
-	help
-	  This selects a driver for the MediaTek MT7621 SPI Controller.
-

drivers/staging/mt7621-spi/Makefile

-obj-$(CONFIG_SPI_MT7621)		+= spi-mt7621.o

drivers/staging/mt7621-spi/TODO

-
-- general code review and clean up
-- ensure device-tree requirements are documented
-
-Cc: NeilBrown <neil@brown.name>

include/linux/platform_data/spi-ep93xx.h

@@ -6,13 +6,9 @@ struct spi_device;
 
 /**
  * struct ep93xx_spi_info - EP93xx specific SPI descriptor
- * @chipselect: array of gpio numbers to use as chip selects
- * @num_chipselect: ARRAY_SIZE(chipselect)
  * @use_dma: use DMA for the transfers
  */
 struct ep93xx_spi_info {
-	int	*chipselect;
-	int	num_chipselect;
 	bool	use_dma;
 };
 

include/linux/spi/pxa2xx_spi.h

@@ -25,6 +25,7 @@ struct dma_chan;
 struct pxa2xx_spi_controller {
 	u16 num_chipselect;
 	u8 enable_dma;
+	u8 dma_burst_size;
 	bool is_slave;
 
 	/* DMA engine specific config */

include/linux/spi/spi-mem.h

@@ -295,6 +295,10 @@ int spi_controller_dma_map_mem_op_data(struct spi_controller *ctlr,
 void spi_controller_dma_unmap_mem_op_data(struct spi_controller *ctlr,
 					  const struct spi_mem_op *op,
 					  struct sg_table *sg);
+
+bool spi_mem_default_supports_op(struct spi_mem *mem,
+				 const struct spi_mem_op *op);
+
 #else
 static inline int
 spi_controller_dma_map_mem_op_data(struct spi_controller *ctlr,
@@ -310,6 +314,14 @@ spi_controller_dma_unmap_mem_op_data(struct spi_controller *ctlr,
 				     struct sg_table *sg)
 {
 }
+
+static inline
+bool spi_mem_default_supports_op(struct spi_mem *mem,
+				 const struct spi_mem_op *op)
+{
+	return false;
+}
+
 #endif /* CONFIG_SPI_MEM */
 
 int spi_mem_adjust_op_size(struct spi_mem *mem, struct spi_mem_op *op);

include/linux/spi/spi.h

@@ -143,7 +143,7 @@ struct spi_device {
 	u32			max_speed_hz;
 	u8			chip_select;
 	u8			bits_per_word;
-	u16			mode;
+	u32			mode;
 #define	SPI_CPHA	0x01			/* clock phase */
 #define	SPI_CPOL	0x02			/* clock polarity */
 #define	SPI_MODE_0	(0|0)			/* (original MicroWire) */
@@ -330,6 +330,9 @@ static inline void spi_unregister_driver(struct spi_driver *sdrv)
  *	must fail if an unrecognized or unsupported mode is requested.
  *	It's always safe to call this unless transfers are pending on
  *	the device whose settings are being modified.
+ * @set_cs_timing: optional hook for SPI devices to request SPI master
+ * controller for configuring specific CS setup time, hold time and inactive
+ * delay interms of clock counts
  * @transfer: adds a message to the controller's transfer queue.
  * @cleanup: frees controller-specific state
  * @can_dma: determine whether this controller supports DMA
@@ -363,6 +366,7 @@ static inline void spi_unregister_driver(struct spi_driver *sdrv)
  * @unprepare_transfer_hardware: there are currently no more messages on the
  *	queue so the subsystem notifies the driver that it may relax the
  *	hardware by issuing this call
+ *
  * @set_cs: set the logic level of the chip select line.  May be called
  *          from interrupt context.
  * @prepare_message: set up the controller to transfer a single message,
@@ -439,13 +443,12 @@ struct spi_controller {
 	u16			dma_alignment;
 
 	/* spi_device.mode flags understood by this controller driver */
-	u16			mode_bits;
+	u32			mode_bits;
 
 	/* bitmask of supported bits_per_word for transfers */
 	u32			bits_per_word_mask;
 #define SPI_BPW_MASK(bits) BIT((bits) - 1)
-#define SPI_BIT_MASK(bits) (((bits) == 32) ? ~0U : (BIT(bits) - 1))
-#define SPI_BPW_RANGE_MASK(min, max) (SPI_BIT_MASK(max) - SPI_BIT_MASK(min - 1))
+#define SPI_BPW_RANGE_MASK(min, max) GENMASK((max) - 1, (min) - 1)
 
 	/* limits on transfer speed */
 	u32			min_speed_hz;
@@ -489,6 +492,17 @@ struct spi_controller {
 	 */
 	int			(*setup)(struct spi_device *spi);
 
+	/*
+	 * set_cs_timing() method is for SPI controllers that supports
+	 * configuring CS timing.
+	 *
+	 * This hook allows SPI client drivers to request SPI controllers
+	 * to configure specific CS timing through spi_set_cs_timing() after
+	 * spi_setup().
+	 */
+	void (*set_cs_timing)(struct spi_device *spi, u8 setup_clk_cycles,
+			      u8 hold_clk_cycles, u8 inactive_clk_cycles);
+
 	/* bidirectional bulk transfers
 	 *
 	 * + The transfer() method may not sleep; its main role is
@@ -1277,7 +1291,7 @@ struct spi_board_info {
 	/* mode becomes spi_device.mode, and is essential for chips
 	 * where the default of SPI_CS_HIGH = 0 is wrong.
 	 */
-	u16		mode;
+	u32		mode;
 
 	/* ... may need additional spi_device chip config data here.
 	 * avoid stuff protocol drivers can set; but include stuff

include/linux/spi/spi_bitbang.h

@@ -44,6 +44,7 @@ extern int spi_bitbang_setup_transfer(struct spi_device *spi,
 
 /* start or stop queue processing */
 extern int spi_bitbang_start(struct spi_bitbang *spi);
+extern int spi_bitbang_init(struct spi_bitbang *spi);
 extern void spi_bitbang_stop(struct spi_bitbang *spi);
 
 #endif	/* __SPI_BITBANG_H */

include/trace/events/spi.h

@@ -131,9 +131,11 @@ DECLARE_EVENT_CLASS(spi_transfer,
 		__field(        struct spi_transfer *,   xfer   )
 		__field(        int,            len             )
 		__dynamic_array(u8, rx_buf,
-				spi_valid_rxbuf(msg, xfer) ? xfer->len : 0)
+				spi_valid_rxbuf(msg, xfer) ?
+					(xfer->len < 64 ? xfer->len : 64) : 0)
 		__dynamic_array(u8, tx_buf,
-				spi_valid_txbuf(msg, xfer) ? xfer->len : 0)
+				spi_valid_txbuf(msg, xfer) ?
+					(xfer->len < 64 ? xfer->len : 64) : 0)
 	),
 
 	TP_fast_assign(
@@ -144,11 +146,11 @@ DECLARE_EVENT_CLASS(spi_transfer,
 
 		if (spi_valid_txbuf(msg, xfer))
 			memcpy(__get_dynamic_array(tx_buf),
-			       xfer->tx_buf, xfer->len);
+			       xfer->tx_buf, __get_dynamic_array_len(tx_buf));
 
 		if (spi_valid_rxbuf(msg, xfer))
 			memcpy(__get_dynamic_array(rx_buf),
-			       xfer->rx_buf, xfer->len);
+			       xfer->rx_buf, __get_dynamic_array_len(rx_buf));
 	),
 
 	TP_printk("spi%d.%d %p len=%d tx=[%*phD] rx=[%*phD]",

include/uapi/linux/spi/spidev.h

@@ -66,6 +66,9 @@
  * @delay_usecs: If nonzero, how long to delay after the last bit transfer
  *	before optionally deselecting the device before the next transfer.
  * @cs_change: True to deselect device before starting the next transfer.
+ * @word_delay_usecs: If nonzero, how long to wait between words within one
+ *	transfer. This property needs explicit support in the SPI controller,
+ *	otherwise it is silently ignored.
  *
  * This structure is mapped directly to the kernel spi_transfer structure;
  * the fields have the same meanings, except of course that the pointers
@@ -100,7 +103,8 @@ struct spi_ioc_transfer {
 	__u8		cs_change;
 	__u8		tx_nbits;
 	__u8		rx_nbits;
-	__u16		pad;
+	__u8		word_delay_usecs;
+	__u8		pad;
 
 	/* If the contents of 'struct spi_ioc_transfer' ever change
 	 * incompatibly, then the ioctl number (currently 0) must change;

sound/soc/codecs/adau1977-spi.c

@@ -10,6 +10,8 @@
 #include <linux/mod_devicetable.h>
 #include <linux/module.h>
 #include <linux/regmap.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
 #include <linux/spi/spi.h>
 #include <sound/soc.h>
 
@@ -54,9 +56,18 @@ static const struct spi_device_id adau1977_spi_ids[] = {
 };
 MODULE_DEVICE_TABLE(spi, adau1977_spi_ids);
 
+static const struct of_device_id adau1977_spi_of_match[] = {
+        { .compatible = "adi,adau1977" },
+        { .compatible = "adi,adau1978" },
+        { .compatible = "adi,adau1979" },
+        { },
+};
+MODULE_DEVICE_TABLE(of, adau1977_spi_of_match);
+
 static struct spi_driver adau1977_spi_driver = {
 	.driver = {
 		.name = "adau1977",
+		.of_match_table = of_match_ptr(adau1977_spi_of_match),
 	},
 	.probe = adau1977_spi_probe,
 	.id_table = adau1977_spi_ids,