Commit 9c6d26df authored by John Stultz's avatar John Stultz Committed by Wei Xu

arm64: dts: hikey: Fix eMMC corruption regression

This patch is a partial revert of
commit abd7d097 ("arm64: dts: hikey: Enable HS200 mode on eMMC")

which has been causing eMMC corruption on my HiKey board.

Symptoms usually looked like:

mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req 400000Hz, actual 400000HZ div = 31)
...
mmc_host mmc0: Bus speed (slot 0) = 148800000Hz (slot req 150000000Hz, actual 148800000HZ div = 0)
mmc0: new HS200 MMC card at address 0001
...
dwmmc_k3 f723d000.dwmmc0: Unexpected command timeout, state 3
mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req 400000Hz, actual 400000HZ div = 31)
mmc_host mmc0: Bus speed (slot 0) = 148800000Hz (slot req 150000000Hz, actual 148800000HZ div = 0)
mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req 400000Hz, actual 400000HZ div = 31)
mmc_host mmc0: Bus speed (slot 0) = 148800000Hz (slot req 150000000Hz, actual 148800000HZ div = 0)
mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req 400000Hz, actual 400000HZ div = 31)
mmc_host mmc0: Bus speed (slot 0) = 148800000Hz (slot req 150000000Hz, actual 148800000HZ div = 0)
print_req_error: I/O error, dev mmcblk0, sector 8810504
Aborting journal on device mmcblk0p10-8.
mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req 400000Hz, actual 400000HZ div = 31)
mmc_host mmc0: Bus speed (slot 0) = 148800000Hz (slot req 150000000Hz, actual 148800000HZ div = 0)
mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req 400000Hz, actual 400000HZ div = 31)
mmc_host mmc0: Bus speed (slot 0) = 148800000Hz (slot req 150000000Hz, actual 148800000HZ div = 0)
mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req 400000Hz, actual 400000HZ div = 31)
mmc_host mmc0: Bus speed (slot 0) = 148800000Hz (slot req 150000000Hz, actual 148800000HZ div = 0)
mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req 400000Hz, actual 400000HZ div = 31)
mmc_host mmc0: Bus speed (slot 0) = 148800000Hz (slot req 150000000Hz, actual 148800000HZ div = 0)
EXT4-fs error (device mmcblk0p10): ext4_journal_check_start:61: Detected aborted journal
EXT4-fs (mmcblk0p10): Remounting filesystem read-only

And quite often this would result in a disk that wouldn't properly
boot even with older kernels.

It seems the max-frequency property added by the above patch is
causing the problem, so remove it.

Cc: Ryan Grachek <ryan@edited.us>
Cc: Wei Xu <xuwei5@hisilicon.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: YongQin Liu <yongqin.liu@linaro.org>
Cc: Leo Yan <leo.yan@linaro.org>
Signed-off-by: default avatarJohn Stultz <john.stultz@linaro.org>
Tested-by: default avatarLeo Yan <leo.yan@linaro.org>
Signed-off-by: default avatarWei Xu <xuwei04@gmail.com>
parent 60cc43fc
...@@ -299,7 +299,6 @@ gpio15: gpio@f702b000 { ...@@ -299,7 +299,6 @@ gpio15: gpio@f702b000 {
/* GPIO blocks 16 thru 19 do not appear to be routed to pins */ /* GPIO blocks 16 thru 19 do not appear to be routed to pins */
dwmmc_0: dwmmc0@f723d000 { dwmmc_0: dwmmc0@f723d000 {
max-frequency = <150000000>;
cap-mmc-highspeed; cap-mmc-highspeed;
mmc-hs200-1_8v; mmc-hs200-1_8v;
non-removable; non-removable;
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment