Commit 9cfe4a93 authored by Michael Hennerich's avatar Michael Hennerich Committed by Linus Torvalds

fbdev: bfin-lq035q1-fb: new Blackfin Landscape LCD EZ-Extender driver

Framebuffer driver for the Landscape LCD EZ-Extender (ADZS-BFLLCD-EZEXT)
http://docs.blackfin.uclinux.org/doku.php?id=hw:cards:landscape_lcd_ez-extenderSigned-off-by: default avatarMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: default avatarBryan Wu <cooloney@kernel.org>
Signed-off-by: default avatarMike Frysinger <vapier@gentoo.org>
Signed-off-by: default avatarAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: default avatarLinus Torvalds <torvalds@linux-foundation.org>
parent 07697461
/*
* Blackfin LCD Framebuffer driver SHARP LQ035Q1DH02
*
* Copyright 2008-2009 Analog Devices Inc.
* Licensed under the GPL-2 or later.
*/
#ifndef BFIN_LQ035Q1_H
#define BFIN_LQ035Q1_H
#define LQ035_RL (0 << 8) /* Right -> Left Scan */
#define LQ035_LR (1 << 8) /* Left -> Right Scan */
#define LQ035_TB (1 << 9) /* Top -> Botton Scan */
#define LQ035_BT (0 << 9) /* Botton -> Top Scan */
#define LQ035_BGR (1 << 11) /* Use BGR format */
#define LQ035_RGB (0 << 11) /* Use RGB format */
#define LQ035_NORM (1 << 13) /* Reversal */
#define LQ035_REV (0 << 13) /* Reversal */
struct bfin_lq035q1fb_disp_info {
unsigned mode;
/* GPIOs */
int use_bl;
unsigned gpio_bl;
};
#endif /* BFIN_LQ035Q1_H */
......@@ -614,6 +614,21 @@ config FB_BFIN_T350MCQB
This display is a QVGA 320x240 24-bit RGB display interfaced by an 8-bit wide PPI
It uses PPI[0..7] PPI_FS1, PPI_FS2 and PPI_CLK.
config FB_BFIN_LQ035Q1
tristate "SHARP LQ035Q1DH02 TFT LCD"
depends on FB && BLACKFIN && SPI
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
select BFIN_GPTIMERS
help
This is the framebuffer device driver for a SHARP LQ035Q1DH02 TFT display found on
the Blackfin Landscape LCD EZ-Extender Card.
This display is a QVGA 320x240 18-bit RGB display interfaced by an 16-bit wide PPI
It uses PPI[0..15] PPI_FS1, PPI_FS2 and PPI_CLK.
To compile this driver as a module, choose M here: the
module will be called bfin-lq035q1-fb.
config FB_STI
tristate "HP STI frame buffer device support"
......
......@@ -137,6 +137,7 @@ obj-$(CONFIG_FB_EFI) += efifb.o
obj-$(CONFIG_FB_VGA16) += vga16fb.o
obj-$(CONFIG_FB_OF) += offb.o
obj-$(CONFIG_FB_BF54X_LQ043) += bf54x-lq043fb.o
obj-$(CONFIG_FB_BFIN_LQ035Q1) += bfin-lq035q1-fb.o
obj-$(CONFIG_FB_BFIN_T350MCQB) += bfin-t350mcqb-fb.o
obj-$(CONFIG_FB_MX3) += mx3fb.o
obj-$(CONFIG_FB_DA8XX) += da8xx-fb.o
......
/*
* Blackfin LCD Framebuffer driver SHARP LQ035Q1DH02
*
* Copyright 2008-2009 Analog Devices Inc.
* Licensed under the GPL-2 or later.
*/
#define DRIVER_NAME "bfin-lq035q1"
#define pr_fmt(fmt) DRIVER_NAME ": " fmt
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/errno.h>
#include <linux/string.h>
#include <linux/fb.h>
#include <linux/init.h>
#include <linux/types.h>
#include <linux/interrupt.h>
#include <linux/device.h>
#include <linux/backlight.h>
#include <linux/lcd.h>
#include <linux/dma-mapping.h>
#include <linux/platform_device.h>
#include <linux/spi/spi.h>
#include <linux/dma-mapping.h>
#include <asm/blackfin.h>
#include <asm/irq.h>
#include <asm/dma.h>
#include <asm/portmux.h>
#include <asm/gptimers.h>
#include <asm/bfin-lq035q1.h>
#if defined(BF533_FAMILY) || defined(BF538_FAMILY)
#define TIMER_HSYNC_id TIMER1_id
#define TIMER_HSYNCbit TIMER1bit
#define TIMER_HSYNC_STATUS_TRUN TIMER_STATUS_TRUN1
#define TIMER_HSYNC_STATUS_TIMIL TIMER_STATUS_TIMIL1
#define TIMER_HSYNC_STATUS_TOVF TIMER_STATUS_TOVF1
#define TIMER_VSYNC_id TIMER2_id
#define TIMER_VSYNCbit TIMER2bit
#define TIMER_VSYNC_STATUS_TRUN TIMER_STATUS_TRUN2
#define TIMER_VSYNC_STATUS_TIMIL TIMER_STATUS_TIMIL2
#define TIMER_VSYNC_STATUS_TOVF TIMER_STATUS_TOVF2
#else
#define TIMER_HSYNC_id TIMER0_id
#define TIMER_HSYNCbit TIMER0bit
#define TIMER_HSYNC_STATUS_TRUN TIMER_STATUS_TRUN0
#define TIMER_HSYNC_STATUS_TIMIL TIMER_STATUS_TIMIL0
#define TIMER_HSYNC_STATUS_TOVF TIMER_STATUS_TOVF0
#define TIMER_VSYNC_id TIMER1_id
#define TIMER_VSYNCbit TIMER1bit
#define TIMER_VSYNC_STATUS_TRUN TIMER_STATUS_TRUN1
#define TIMER_VSYNC_STATUS_TIMIL TIMER_STATUS_TIMIL1
#define TIMER_VSYNC_STATUS_TOVF TIMER_STATUS_TOVF1
#endif
#define LCD_X_RES 320 /* Horizontal Resolution */
#define LCD_Y_RES 240 /* Vertical Resolution */
#define DMA_BUS_SIZE 16
#define USE_RGB565_16_BIT_PPI
#ifdef USE_RGB565_16_BIT_PPI
#define LCD_BPP 16 /* Bit Per Pixel */
#define CLOCKS_PER_PIX 1
#define CPLD_PIPELINE_DELAY_COR 0 /* NO CPLB */
#endif
/* Interface 16/18-bit TFT over an 8-bit wide PPI using a small Programmable Logic Device (CPLD)
* http://blackfin.uclinux.org/gf/project/stamp/frs/?action=FrsReleaseBrowse&frs_package_id=165
*/
#ifdef USE_RGB565_8_BIT_PPI
#define LCD_BPP 16 /* Bit Per Pixel */
#define CLOCKS_PER_PIX 2
#define CPLD_PIPELINE_DELAY_COR 3 /* RGB565 */
#endif
#ifdef USE_RGB888_8_BIT_PPI
#define LCD_BPP 24 /* Bit Per Pixel */
#define CLOCKS_PER_PIX 3
#define CPLD_PIPELINE_DELAY_COR 5 /* RGB888 */
#endif
/*
* HS and VS timing parameters (all in number of PPI clk ticks)
*/
#define U_LINE 4 /* Blanking Lines */
#define H_ACTPIX (LCD_X_RES * CLOCKS_PER_PIX) /* active horizontal pixel */
#define H_PERIOD (336 * CLOCKS_PER_PIX) /* HS period */
#define H_PULSE (2 * CLOCKS_PER_PIX) /* HS pulse width */
#define H_START (7 * CLOCKS_PER_PIX + CPLD_PIPELINE_DELAY_COR) /* first valid pixel */
#define V_LINES (LCD_Y_RES + U_LINE) /* total vertical lines */
#define V_PULSE (2 * CLOCKS_PER_PIX) /* VS pulse width (1-5 H_PERIODs) */
#define V_PERIOD (H_PERIOD * V_LINES) /* VS period */
#define ACTIVE_VIDEO_MEM_OFFSET ((U_LINE / 2) * LCD_X_RES * (LCD_BPP / 8))
#define BFIN_LCD_NBR_PALETTE_ENTRIES 256
#define PPI_TX_MODE 0x2
#define PPI_XFER_TYPE_11 0xC
#define PPI_PORT_CFG_01 0x10
#define PPI_POLS_1 0x8000
#if (CLOCKS_PER_PIX > 1)
#define PPI_PMODE (DLEN_8 | PACK_EN)
#else
#define PPI_PMODE (DLEN_16)
#endif
#define LQ035_INDEX 0x74
#define LQ035_DATA 0x76
#define LQ035_DRIVER_OUTPUT_CTL 0x1
#define LQ035_SHUT_CTL 0x11
#define LQ035_DRIVER_OUTPUT_MASK (LQ035_LR | LQ035_TB | LQ035_BGR | LQ035_REV)
#define LQ035_DRIVER_OUTPUT_DEFAULT (0x2AEF & ~LQ035_DRIVER_OUTPUT_MASK)
#define LQ035_SHUT (1 << 0) /* Shutdown */
#define LQ035_ON (0 << 0) /* Shutdown */
struct bfin_lq035q1fb_info {
struct fb_info *fb;
struct device *dev;
struct spi_driver spidrv;
struct bfin_lq035q1fb_disp_info *disp_info;
unsigned char *fb_buffer; /* RGB Buffer */
dma_addr_t dma_handle;
int lq035_open_cnt;
int irq;
spinlock_t lock; /* lock */
u32 pseudo_pal[16];
};
static int nocursor;
module_param(nocursor, int, 0644);
MODULE_PARM_DESC(nocursor, "cursor enable/disable");
struct spi_control {
unsigned short mode;
};
static int lq035q1_control(struct spi_device *spi, unsigned char reg, unsigned short value)
{
int ret;
u8 regs[3] = { LQ035_INDEX, 0, 0 };
u8 dat[3] = { LQ035_DATA, 0, 0 };
if (!spi)
return -ENODEV;
regs[2] = reg;
dat[1] = value >> 8;
dat[2] = value & 0xFF;
ret = spi_write(spi, regs, ARRAY_SIZE(regs));
ret |= spi_write(spi, dat, ARRAY_SIZE(dat));
return ret;
}
static int __devinit lq035q1_spidev_probe(struct spi_device *spi)
{
int ret;
struct spi_control *ctl;
struct bfin_lq035q1fb_info *info = container_of(spi->dev.driver,
struct bfin_lq035q1fb_info,
spidrv.driver);
ctl = kzalloc(sizeof(*ctl), GFP_KERNEL);
if (!ctl)
return -ENOMEM;
ctl->mode = (info->disp_info->mode &
LQ035_DRIVER_OUTPUT_MASK) | LQ035_DRIVER_OUTPUT_DEFAULT;
ret = lq035q1_control(spi, LQ035_SHUT_CTL, LQ035_ON);
ret |= lq035q1_control(spi, LQ035_DRIVER_OUTPUT_CTL, ctl->mode);
if (ret)
return ret;
spi_set_drvdata(spi, ctl);
return 0;
}
static int lq035q1_spidev_remove(struct spi_device *spi)
{
return lq035q1_control(spi, LQ035_SHUT_CTL, LQ035_SHUT);
}
#ifdef CONFIG_PM
static int lq035q1_spidev_suspend(struct spi_device *spi, pm_message_t state)
{
return lq035q1_control(spi, LQ035_SHUT_CTL, LQ035_SHUT);
}
static int lq035q1_spidev_resume(struct spi_device *spi)
{
int ret;
struct spi_control *ctl = spi_get_drvdata(spi);
ret = lq035q1_control(spi, LQ035_DRIVER_OUTPUT_CTL, ctl->mode);
if (ret)
return ret;
return lq035q1_control(spi, LQ035_SHUT_CTL, LQ035_ON);
}
#else
# define lq035q1_spidev_suspend NULL
# define lq035q1_spidev_resume NULL
#endif
/* Power down all displays on reboot, poweroff or halt */
static void lq035q1_spidev_shutdown(struct spi_device *spi)
{
lq035q1_control(spi, LQ035_SHUT_CTL, LQ035_SHUT);
}
static int lq035q1_backlight(struct bfin_lq035q1fb_info *info, unsigned arg)
{
if (info->disp_info->use_bl)
gpio_set_value(info->disp_info->gpio_bl, arg);
return 0;
}
static void bfin_lq035q1_config_ppi(struct bfin_lq035q1fb_info *fbi)
{
bfin_write_PPI_DELAY(H_START);
bfin_write_PPI_COUNT(H_ACTPIX - 1);
bfin_write_PPI_FRAME(V_LINES);
bfin_write_PPI_CONTROL(PPI_TX_MODE | /* output mode , PORT_DIR */
PPI_XFER_TYPE_11 | /* sync mode XFR_TYPE */
PPI_PORT_CFG_01 | /* two frame sync PORT_CFG */
PPI_PMODE | /* 8/16 bit data length / PACK_EN? */
PPI_POLS_1); /* faling edge syncs POLS */
}
static inline void bfin_lq035q1_disable_ppi(void)
{
bfin_write_PPI_CONTROL(bfin_read_PPI_CONTROL() & ~PORT_EN);
}
static inline void bfin_lq035q1_enable_ppi(void)
{
bfin_write_PPI_CONTROL(bfin_read_PPI_CONTROL() | PORT_EN);
}
static void bfin_lq035q1_start_timers(void)
{
enable_gptimers(TIMER_VSYNCbit | TIMER_HSYNCbit);
}
static void bfin_lq035q1_stop_timers(void)
{
disable_gptimers(TIMER_HSYNCbit | TIMER_VSYNCbit);
set_gptimer_status(0, TIMER_HSYNC_STATUS_TRUN | TIMER_VSYNC_STATUS_TRUN |
TIMER_HSYNC_STATUS_TIMIL | TIMER_VSYNC_STATUS_TIMIL |
TIMER_HSYNC_STATUS_TOVF | TIMER_VSYNC_STATUS_TOVF);
}
static void bfin_lq035q1_init_timers(void)
{
bfin_lq035q1_stop_timers();
set_gptimer_period(TIMER_HSYNC_id, H_PERIOD);
set_gptimer_pwidth(TIMER_HSYNC_id, H_PULSE);
set_gptimer_config(TIMER_HSYNC_id, TIMER_MODE_PWM | TIMER_PERIOD_CNT |
TIMER_TIN_SEL | TIMER_CLK_SEL|
TIMER_EMU_RUN);
set_gptimer_period(TIMER_VSYNC_id, V_PERIOD);
set_gptimer_pwidth(TIMER_VSYNC_id, V_PULSE);
set_gptimer_config(TIMER_VSYNC_id, TIMER_MODE_PWM | TIMER_PERIOD_CNT |
TIMER_TIN_SEL | TIMER_CLK_SEL |
TIMER_EMU_RUN);
}
static void bfin_lq035q1_config_dma(struct bfin_lq035q1fb_info *fbi)
{
set_dma_config(CH_PPI,
set_bfin_dma_config(DIR_READ, DMA_FLOW_AUTO,
INTR_DISABLE, DIMENSION_2D,
DATA_SIZE_16,
DMA_NOSYNC_KEEP_DMA_BUF));
set_dma_x_count(CH_PPI, (LCD_X_RES * LCD_BPP) / DMA_BUS_SIZE);
set_dma_x_modify(CH_PPI, DMA_BUS_SIZE / 8);
set_dma_y_count(CH_PPI, V_LINES);
set_dma_y_modify(CH_PPI, DMA_BUS_SIZE / 8);
set_dma_start_addr(CH_PPI, (unsigned long)fbi->fb_buffer);
}
#if (CLOCKS_PER_PIX == 1)
static const u16 ppi0_req_16[] = {P_PPI0_CLK, P_PPI0_FS1, P_PPI0_FS2,
P_PPI0_D0, P_PPI0_D1, P_PPI0_D2,
P_PPI0_D3, P_PPI0_D4, P_PPI0_D5,
P_PPI0_D6, P_PPI0_D7, P_PPI0_D8,
P_PPI0_D9, P_PPI0_D10, P_PPI0_D11,
P_PPI0_D12, P_PPI0_D13, P_PPI0_D14,
P_PPI0_D15, 0};
#else
static const u16 ppi0_req_16[] = {P_PPI0_CLK, P_PPI0_FS1, P_PPI0_FS2,
P_PPI0_D0, P_PPI0_D1, P_PPI0_D2,
P_PPI0_D3, P_PPI0_D4, P_PPI0_D5,
P_PPI0_D6, P_PPI0_D7, 0};
#endif
static inline void bfin_lq035q1_free_ports(void)
{
peripheral_free_list(ppi0_req_16);
if (ANOMALY_05000400)
gpio_free(P_IDENT(P_PPI0_FS3));
}
static int __devinit bfin_lq035q1_request_ports(struct platform_device *pdev)
{
/* ANOMALY_05000400 - PPI Does Not Start Properly In Specific Mode:
* Drive PPI_FS3 Low
*/
if (ANOMALY_05000400) {
int ret = gpio_request(P_IDENT(P_PPI0_FS3), "PPI_FS3");
if (ret)
return ret;
gpio_direction_output(P_IDENT(P_PPI0_FS3), 0);
}
if (peripheral_request_list(ppi0_req_16, DRIVER_NAME)) {
dev_err(&pdev->dev, "requesting peripherals failed\n");
return -EFAULT;
}
return 0;
}
static int bfin_lq035q1_fb_open(struct fb_info *info, int user)
{
struct bfin_lq035q1fb_info *fbi = info->par;
spin_lock(&fbi->lock);
fbi->lq035_open_cnt++;
if (fbi->lq035_open_cnt <= 1) {
bfin_lq035q1_disable_ppi();
SSYNC();
bfin_lq035q1_config_dma(fbi);
bfin_lq035q1_config_ppi(fbi);
bfin_lq035q1_init_timers();
/* start dma */
enable_dma(CH_PPI);
bfin_lq035q1_enable_ppi();
bfin_lq035q1_start_timers();
lq035q1_backlight(fbi, 1);
}
spin_unlock(&fbi->lock);
return 0;
}
static int bfin_lq035q1_fb_release(struct fb_info *info, int user)
{
struct bfin_lq035q1fb_info *fbi = info->par;
spin_lock(&fbi->lock);
fbi->lq035_open_cnt--;
if (fbi->lq035_open_cnt <= 0) {
lq035q1_backlight(fbi, 0);
bfin_lq035q1_disable_ppi();
SSYNC();
disable_dma(CH_PPI);
bfin_lq035q1_stop_timers();
}
spin_unlock(&fbi->lock);
return 0;
}
static int bfin_lq035q1_fb_check_var(struct fb_var_screeninfo *var,
struct fb_info *info)
{
switch (var->bits_per_pixel) {
#if (LCD_BPP == 24)
case 24:/* TRUECOLOUR, 16m */
#else
case 16:/* DIRECTCOLOUR, 64k */
#endif
var->red.offset = info->var.red.offset;
var->green.offset = info->var.green.offset;
var->blue.offset = info->var.blue.offset;
var->red.length = info->var.red.length;
var->green.length = info->var.green.length;
var->blue.length = info->var.blue.length;
var->transp.offset = 0;
var->transp.length = 0;
var->transp.msb_right = 0;
var->red.msb_right = 0;
var->green.msb_right = 0;
var->blue.msb_right = 0;
break;
default:
pr_debug("%s: depth not supported: %u BPP\n", __func__,
var->bits_per_pixel);
return -EINVAL;
}
if (info->var.xres != var->xres || info->var.yres != var->yres ||
info->var.xres_virtual != var->xres_virtual ||
info->var.yres_virtual != var->yres_virtual) {
pr_debug("%s: Resolution not supported: X%u x Y%u \n",
__func__, var->xres, var->yres);
return -EINVAL;
}
/*
* Memory limit
*/
if ((info->fix.line_length * var->yres_virtual) > info->fix.smem_len) {
pr_debug("%s: Memory Limit requested yres_virtual = %u\n",
__func__, var->yres_virtual);
return -ENOMEM;
}
return 0;
}
int bfin_lq035q1_fb_cursor(struct fb_info *info, struct fb_cursor *cursor)
{
if (nocursor)
return 0;
else
return -EINVAL; /* just to force soft_cursor() call */
}
static int bfin_lq035q1_fb_setcolreg(u_int regno, u_int red, u_int green,
u_int blue, u_int transp,
struct fb_info *info)
{
if (regno >= BFIN_LCD_NBR_PALETTE_ENTRIES)
return -EINVAL;
if (info->var.grayscale) {
/* grayscale = 0.30*R + 0.59*G + 0.11*B */
red = green = blue = (red * 77 + green * 151 + blue * 28) >> 8;
}
if (info->fix.visual == FB_VISUAL_TRUECOLOR) {
u32 value;
/* Place color in the pseudopalette */
if (regno > 16)
return -EINVAL;
red >>= (16 - info->var.red.length);
green >>= (16 - info->var.green.length);
blue >>= (16 - info->var.blue.length);
value = (red << info->var.red.offset) |
(green << info->var.green.offset) |
(blue << info->var.blue.offset);
value &= 0xFFFFFF;
((u32 *) (info->pseudo_palette))[regno] = value;
}
return 0;
}
static struct fb_ops bfin_lq035q1_fb_ops = {
.owner = THIS_MODULE,
.fb_open = bfin_lq035q1_fb_open,
.fb_release = bfin_lq035q1_fb_release,
.fb_check_var = bfin_lq035q1_fb_check_var,
.fb_fillrect = cfb_fillrect,
.fb_copyarea = cfb_copyarea,
.fb_imageblit = cfb_imageblit,
.fb_cursor = bfin_lq035q1_fb_cursor,
.fb_setcolreg = bfin_lq035q1_fb_setcolreg,
};
static irqreturn_t bfin_lq035q1_irq_error(int irq, void *dev_id)
{
/*struct bfin_lq035q1fb_info *info = (struct bfin_lq035q1fb_info *)dev_id;*/
u16 status = bfin_read_PPI_STATUS();
bfin_write_PPI_STATUS(-1);
if (status) {
bfin_lq035q1_disable_ppi();
disable_dma(CH_PPI);
/* start dma */
enable_dma(CH_PPI);
bfin_lq035q1_enable_ppi();
bfin_write_PPI_STATUS(-1);
}
return IRQ_HANDLED;
}
static int __devinit bfin_lq035q1_probe(struct platform_device *pdev)
{
struct bfin_lq035q1fb_info *info;
struct fb_info *fbinfo;
int ret;
ret = request_dma(CH_PPI, DRIVER_NAME"_CH_PPI");
if (ret < 0) {
dev_err(&pdev->dev, "PPI DMA unavailable\n");
goto out1;
}
fbinfo = framebuffer_alloc(sizeof(*info), &pdev->dev);
if (!fbinfo) {
ret = -ENOMEM;
goto out2;
}
info = fbinfo->par;
info->fb = fbinfo;
info->dev = &pdev->dev;
info->disp_info = pdev->dev.platform_data;
platform_set_drvdata(pdev, fbinfo);
strcpy(fbinfo->fix.id, DRIVER_NAME);
fbinfo->fix.type = FB_TYPE_PACKED_PIXELS;
fbinfo->fix.type_aux = 0;
fbinfo->fix.xpanstep = 0;
fbinfo->fix.ypanstep = 0;
fbinfo->fix.ywrapstep = 0;
fbinfo->fix.accel = FB_ACCEL_NONE;
fbinfo->fix.visual = FB_VISUAL_TRUECOLOR;
fbinfo->var.nonstd = 0;
fbinfo->var.activate = FB_ACTIVATE_NOW;
fbinfo->var.height = -1;
fbinfo->var.width = -1;
fbinfo->var.accel_flags = 0;
fbinfo->var.vmode = FB_VMODE_NONINTERLACED;
fbinfo->var.xres = LCD_X_RES;
fbinfo->var.xres_virtual = LCD_X_RES;
fbinfo->var.yres = LCD_Y_RES;
fbinfo->var.yres_virtual = LCD_Y_RES;
fbinfo->var.bits_per_pixel = LCD_BPP;
if (info->disp_info->mode & LQ035_BGR) {
#if (LCD_BPP == 24)
fbinfo->var.red.offset = 0;
fbinfo->var.green.offset = 8;
fbinfo->var.blue.offset = 16;
#else
fbinfo->var.red.offset = 0;
fbinfo->var.green.offset = 5;
fbinfo->var.blue.offset = 11;
#endif
} else {
#if (LCD_BPP == 24)
fbinfo->var.red.offset = 16;
fbinfo->var.green.offset = 8;
fbinfo->var.blue.offset = 0;
#else
fbinfo->var.red.offset = 11;
fbinfo->var.green.offset = 5;
fbinfo->var.blue.offset = 0;
#endif
}
fbinfo->var.transp.offset = 0;
#if (LCD_BPP == 24)
fbinfo->var.red.length = 8;
fbinfo->var.green.length = 8;
fbinfo->var.blue.length = 8;
#else
fbinfo->var.red.length = 5;
fbinfo->var.green.length = 6;
fbinfo->var.blue.length = 5;
#endif
fbinfo->var.transp.length = 0;
fbinfo->fix.smem_len = LCD_X_RES * LCD_Y_RES * LCD_BPP / 8
+ ACTIVE_VIDEO_MEM_OFFSET;
fbinfo->fix.line_length = fbinfo->var.xres_virtual *
fbinfo->var.bits_per_pixel / 8;
fbinfo->fbops = &bfin_lq035q1_fb_ops;
fbinfo->flags = FBINFO_FLAG_DEFAULT;
info->fb_buffer =
dma_alloc_coherent(NULL, fbinfo->fix.smem_len, &info->dma_handle,
GFP_KERNEL);
if (NULL == info->fb_buffer) {
dev_err(&pdev->dev, "couldn't allocate dma buffer\n");
ret = -ENOMEM;
goto out3;
}
fbinfo->screen_base = (void *)info->fb_buffer + ACTIVE_VIDEO_MEM_OFFSET;
fbinfo->fix.smem_start = (int)info->fb_buffer + ACTIVE_VIDEO_MEM_OFFSET;
fbinfo->fbops = &bfin_lq035q1_fb_ops;
fbinfo->pseudo_palette = &info->pseudo_pal;
ret = fb_alloc_cmap(&fbinfo->cmap, BFIN_LCD_NBR_PALETTE_ENTRIES, 0);
if (ret < 0) {
dev_err(&pdev->dev, "failed to allocate colormap (%d entries)\n",
BFIN_LCD_NBR_PALETTE_ENTRIES);
goto out4;
}
ret = bfin_lq035q1_request_ports(pdev);
if (ret) {
dev_err(&pdev->dev, "couldn't request gpio port\n");
goto out6;
}
info->irq = platform_get_irq(pdev, 0);
if (info->irq < 0) {
ret = -EINVAL;
goto out7;
}
ret = request_irq(info->irq, bfin_lq035q1_irq_error, IRQF_DISABLED,
DRIVER_NAME" PPI ERROR", info);
if (ret < 0) {
dev_err(&pdev->dev, "unable to request PPI ERROR IRQ\n");
goto out7;
}
info->spidrv.driver.name = DRIVER_NAME"-spi";
info->spidrv.probe = lq035q1_spidev_probe;
info->spidrv.remove = __devexit_p(lq035q1_spidev_remove);
info->spidrv.shutdown = lq035q1_spidev_shutdown;
info->spidrv.suspend = lq035q1_spidev_suspend;
info->spidrv.resume = lq035q1_spidev_resume;
ret = spi_register_driver(&info->spidrv);
if (ret < 0) {
dev_err(&pdev->dev, "couldn't register SPI Interface\n");
goto out8;
}
if (info->disp_info->use_bl) {
ret = gpio_request(info->disp_info->gpio_bl, "LQ035 Backlight");
if (ret) {
dev_err(&pdev->dev, "failed to request GPIO %d\n",
info->disp_info->gpio_bl);
goto out9;
}
gpio_direction_output(info->disp_info->gpio_bl, 0);
}
ret = register_framebuffer(fbinfo);
if (ret < 0) {
dev_err(&pdev->dev, "unable to register framebuffer\n");
goto out10;
}
dev_info(&pdev->dev, "%dx%d %d-bit RGB FrameBuffer initialized\n",
LCD_X_RES, LCD_Y_RES, LCD_BPP);
return 0;
out10:
if (info->disp_info->use_bl)
gpio_free(info->disp_info->gpio_bl);
out9:
spi_unregister_driver(&info->spidrv);
out8:
free_irq(info->irq, info);
out7:
bfin_lq035q1_free_ports();
out6:
fb_dealloc_cmap(&fbinfo->cmap);
out4:
dma_free_coherent(NULL, fbinfo->fix.smem_len, info->fb_buffer,
info->dma_handle);
out3:
framebuffer_release(fbinfo);
out2:
free_dma(CH_PPI);
out1:
platform_set_drvdata(pdev, NULL);
return ret;
}
static int __devexit bfin_lq035q1_remove(struct platform_device *pdev)
{
struct fb_info *fbinfo = platform_get_drvdata(pdev);
struct bfin_lq035q1fb_info *info = fbinfo->par;
if (info->disp_info->use_bl)
gpio_free(info->disp_info->gpio_bl);
spi_unregister_driver(&info->spidrv);
unregister_framebuffer(fbinfo);
free_dma(CH_PPI);
free_irq(info->irq, info);
if (info->fb_buffer != NULL)
dma_free_coherent(NULL, fbinfo->fix.smem_len, info->fb_buffer,
info->dma_handle);
fb_dealloc_cmap(&fbinfo->cmap);
bfin_lq035q1_free_ports();
platform_set_drvdata(pdev, NULL);
framebuffer_release(fbinfo);
dev_info(&pdev->dev, "unregistered LCD driver\n");
return 0;
}
#ifdef CONFIG_PM
static int bfin_lq035q1_suspend(struct device *dev)
{
struct fb_info *fbinfo = dev_get_drvdata(dev);
struct bfin_lq035q1fb_info *info = fbinfo->par;
if (info->lq035_open_cnt) {
lq035q1_backlight(info, 0);
bfin_lq035q1_disable_ppi();
SSYNC();
disable_dma(CH_PPI);
bfin_lq035q1_stop_timers();
bfin_write_PPI_STATUS(-1);
}
return 0;
}
static int bfin_lq035q1_resume(struct device *dev)
{
struct fb_info *fbinfo = dev_get_drvdata(dev);
struct bfin_lq035q1fb_info *info = fbinfo->par;
if (info->lq035_open_cnt) {
bfin_lq035q1_disable_ppi();
SSYNC();
bfin_lq035q1_config_dma(info);
bfin_lq035q1_config_ppi(info);
bfin_lq035q1_init_timers();
/* start dma */
enable_dma(CH_PPI);
bfin_lq035q1_enable_ppi();
bfin_lq035q1_start_timers();
lq035q1_backlight(info, 1);
}
return 0;
}
static struct dev_pm_ops bfin_lq035q1_dev_pm_ops = {
.suspend = bfin_lq035q1_suspend,
.resume = bfin_lq035q1_resume,
};
#endif
static struct platform_driver bfin_lq035q1_driver = {
.probe = bfin_lq035q1_probe,
.remove = __devexit_p(bfin_lq035q1_remove),
.driver = {
.name = DRIVER_NAME,
#ifdef CONFIG_PM
.pm = &bfin_lq035q1_dev_pm_ops,
#endif
},
};
static int __init bfin_lq035q1_driver_init(void)
{
return platform_driver_register(&bfin_lq035q1_driver);
}
module_init(bfin_lq035q1_driver_init);
static void __exit bfin_lq035q1_driver_cleanup(void)
{
platform_driver_unregister(&bfin_lq035q1_driver);
}
module_exit(bfin_lq035q1_driver_cleanup);
MODULE_DESCRIPTION("Blackfin TFT LCD Driver");
MODULE_LICENSE("GPL");
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment