Commit 9d3de3c5 authored by Maxime Ripard's avatar Maxime Ripard Committed by Rob Herring

dt-bindings: net: Add YAML schemas for the generic Ethernet options

The Ethernet controllers have a good number of generic options that can be
needed in a device tree. Add a YAML schemas for those.
Reviewed-by: default avatarRob Herring <robh@kernel.org>
Signed-off-by: default avatarMaxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: default avatarAndrew Lunn <andrew@lunn.ch>
Signed-off-by: default avatarRob Herring <robh@kernel.org>
parent 5025ef8b
# SPDX-License-Identifier: GPL-2.0
%YAML 1.2
---
$id: http://devicetree.org/schemas/net/ethernet-controller.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#
title: Ethernet Controller Generic Binding
maintainers:
- David S. Miller <davem@davemloft.net>
properties:
$nodename:
pattern: "^ethernet(@.*)?$"
local-mac-address:
allOf:
- $ref: /schemas/types.yaml#definitions/uint8-array
- items:
- minItems: 6
maxItems: 6
description:
Specifies the MAC address that was assigned to the network device.
mac-address:
allOf:
- $ref: /schemas/types.yaml#definitions/uint8-array
- items:
- minItems: 6
maxItems: 6
description:
Specifies the MAC address that was last used by the boot
program; should be used in cases where the MAC address assigned
to the device by the boot program is different from the
local-mac-address property.
max-frame-size:
$ref: /schemas/types.yaml#definitions/uint32
description:
Maximum transfer unit (IEEE defined MTU), rather than the
maximum frame size (there\'s contradiction in the Devicetree
Specification).
max-speed:
$ref: /schemas/types.yaml#definitions/uint32
description:
Specifies maximum speed in Mbit/s supported by the device.
nvmem-cells:
maxItems: 1
description:
Reference to an nvmem node for the MAC address
nvmem-cells-names:
const: mac-address
phy-connection-type:
description:
Operation mode of the PHY interface
enum:
# There is not a standard bus between the MAC and the PHY,
# something proprietary is being used to embed the PHY in the
# MAC.
- internal
- mii
- gmii
- sgmii
- qsgmii
- tbi
- rev-mii
- rmii
# RX and TX delays are added by the MAC when required
- rgmii
# RGMII with internal RX and TX delays provided by the PHY,
# the MAC should not add the RX or TX delays in this case
- rgmii-id
# RGMII with internal RX delay provided by the PHY, the MAC
# should not add an RX delay in this case
- rgmii-rxid
# RGMII with internal TX delay provided by the PHY, the MAC
# should not add an TX delay in this case
- rgmii-txid
- rtbi
- smii
- xgmii
- trgmii
- 1000base-x
- 2500base-x
- rxaui
- xaui
# 10GBASE-KR, XFI, SFI
- 10gbase-kr
- usxgmii
phy-mode:
$ref: "#/properties/phy-connection-type"
phy-handle:
$ref: /schemas/types.yaml#definitions/phandle
description:
Specifies a reference to a node representing a PHY device.
phy:
$ref: "#/properties/phy-handle"
deprecated: true
phy-device:
$ref: "#/properties/phy-handle"
deprecated: true
rx-fifo-depth:
$ref: /schemas/types.yaml#definitions/uint32
description:
The size of the controller\'s receive fifo in bytes. This is used
for components that can have configurable receive fifo sizes,
and is useful for determining certain configuration settings
such as flow control thresholds.
tx-fifo-depth:
$ref: /schemas/types.yaml#definitions/uint32
description:
The size of the controller\'s transmit fifo in bytes. This
is used for components that can have configurable fifo sizes.
managed:
allOf:
- $ref: /schemas/types.yaml#definitions/string
- default: auto
enum:
- auto
- in-band-status
description:
Specifies the PHY management type. If auto is set and fixed-link
is not specified, it uses MDIO for management.
fixed-link:
allOf:
- if:
type: array
then:
deprecated: true
minItems: 1
maxItems: 1
items:
items:
- minimum: 0
maximum: 31
description:
Emulated PHY ID, choose any but unique to the all
specified fixed-links
- enum: [0, 1]
description:
Duplex configuration. 0 for half duplex or 1 for
full duplex
- enum: [10, 100, 1000]
description:
Link speed in Mbits/sec.
- enum: [0, 1]
description:
Pause configuration. 0 for no pause, 1 for pause
- enum: [0, 1]
description:
Asymmetric pause configuration. 0 for no asymmetric
pause, 1 for asymmetric pause
- if:
type: object
then:
properties:
speed:
allOf:
- $ref: /schemas/types.yaml#definitions/uint32
- enum: [10, 100, 1000]
description:
Link speed.
full-duplex:
$ref: /schemas/types.yaml#definitions/flag
description:
Indicates that full-duplex is used. When absent, half
duplex is assumed.
asym-pause:
$ref: /schemas/types.yaml#definitions/flag
description:
Indicates that asym_pause should be enabled.
link-gpios:
maxItems: 1
description:
GPIO to determine if the link is up
required:
- speed
...
The following properties are common to the Ethernet controllers: This file has moved to ethernet-controller.yaml.
NOTE: All 'phy*' properties documented below are Ethernet specific. For the
generic PHY 'phys' property, see
Documentation/devicetree/bindings/phy/phy-bindings.txt.
- mac-address: array of 6 bytes, specifies the MAC address that was last used by
the boot program; should be used in cases where the MAC address assigned to
the device by the boot program is different from the "local-mac-address"
property;
- local-mac-address: array of 6 bytes, specifies the MAC address that was
assigned to the network device;
- nvmem-cells: phandle, reference to an nvmem node for the MAC address
- nvmem-cell-names: string, should be "mac-address" if nvmem is to be used
- max-speed: number, specifies maximum speed in Mbit/s supported by the device;
- max-frame-size: number, maximum transfer unit (IEEE defined MTU), rather than
the maximum frame size (there's contradiction in the Devicetree
Specification).
- phy-mode: string, operation mode of the PHY interface. This is now a de-facto
standard property; supported values are:
* "internal" (Internal means there is not a standard bus between the MAC and
the PHY, something proprietary is being used to embed the PHY in the MAC.)
* "mii"
* "gmii"
* "sgmii"
* "qsgmii"
* "tbi"
* "rev-mii"
* "rmii"
* "rgmii" (RX and TX delays are added by the MAC when required)
* "rgmii-id" (RGMII with internal RX and TX delays provided by the PHY, the
MAC should not add the RX or TX delays in this case)
* "rgmii-rxid" (RGMII with internal RX delay provided by the PHY, the MAC
should not add an RX delay in this case)
* "rgmii-txid" (RGMII with internal TX delay provided by the PHY, the MAC
should not add an TX delay in this case)
* "rtbi"
* "smii"
* "xgmii"
* "trgmii"
* "1000base-x",
* "2500base-x",
* "rxaui"
* "xaui"
* "10gbase-kr" (10GBASE-KR, XFI, SFI)
- phy-connection-type: the same as "phy-mode" property but described in the
Devicetree Specification;
- phy-handle: phandle, specifies a reference to a node representing a PHY
device; this property is described in the Devicetree Specification and so
preferred;
- phy: the same as "phy-handle" property, not recommended for new bindings.
- phy-device: the same as "phy-handle" property, not recommended for new
bindings.
- rx-fifo-depth: the size of the controller's receive fifo in bytes. This
is used for components that can have configurable receive fifo sizes,
and is useful for determining certain configuration settings such as
flow control thresholds.
- tx-fifo-depth: the size of the controller's transmit fifo in bytes. This
is used for components that can have configurable fifo sizes.
- managed: string, specifies the PHY management type. Supported values are:
"auto", "in-band-status". "auto" is the default, it usess MDIO for
management if fixed-link is not specified.
Child nodes of the Ethernet controller are typically the individual PHY devices
connected via the MDIO bus (sometimes the MDIO bus controller is separate).
They are described in the phy.txt file in this same directory.
For non-MDIO PHY management see fixed-link.txt.
Fixed link Device Tree binding This file has moved to ethernet-controller.yaml.
------------------------------
Some Ethernet MACs have a "fixed link", and are not connected to a
normal MDIO-managed PHY device. For those situations, a Device Tree
binding allows to describe a "fixed link".
Such a fixed link situation is described by creating a 'fixed-link'
sub-node of the Ethernet MAC device node, with the following
properties:
* 'speed' (integer, mandatory), to indicate the link speed. Accepted
values are 10, 100 and 1000
* 'full-duplex' (boolean, optional), to indicate that full duplex is
used. When absent, half duplex is assumed.
* 'pause' (boolean, optional), to indicate that pause should be
enabled.
* 'asym-pause' (boolean, optional), to indicate that asym_pause should
be enabled.
* 'link-gpios' ('gpio-list', optional), to indicate if a gpio can be read
to determine if the link is up.
Old, deprecated 'fixed-link' binding:
* A 'fixed-link' property in the Ethernet MAC node, with 5 cells, of the
form <a b c d e> with the following accepted values:
- a: emulated PHY ID, choose any but but unique to the all specified
fixed-links, from 0 to 31
- b: duplex configuration: 0 for half duplex, 1 for full duplex
- c: link speed in Mbits/sec, accepted values are: 10, 100 and 1000
- d: pause configuration: 0 for no pause, 1 for pause
- e: asymmetric pause configuration: 0 for no asymmetric pause, 1 for
asymmetric pause
Examples:
ethernet@0 {
...
fixed-link {
speed = <1000>;
full-duplex;
};
...
};
ethernet@1 {
...
fixed-link {
speed = <1000>;
pause;
link-gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>;
};
...
};
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment