V4L/DVB: STAGING: remove lirc_ene0100 driver

Add latest unported version of this driver to media/IR.
Next patch will port it to ir core.
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

drivers/media/IR/ene_ir.h

+/*
+ * driver for ENE KB3926 B/C/D CIR (also known as ENE0100/ENE0200/ENE0201)
+ *
+ * Copyright (C) 2010 Maxim Levitsky <maximlevitsky@gmail.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful, but
+ * WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
+ * General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307
+ * USA
+ */
+#include <linux/spinlock.h>
+#include <media/lirc.h>
+#include <media/lirc_dev.h>
+
+/* hardware address */
+#define ENE_STATUS		0	/* hardware status - unused */
+#define ENE_ADDR_HI		1	/* hi byte of register address */
+#define ENE_ADDR_LO		2	/* low byte of register address */
+#define ENE_IO			3	/* read/write window */
+#define ENE_MAX_IO		4
+
+/* 8 bytes of samples, divided in 2 halfs*/
+#define ENE_SAMPLE_BUFFER	0xF8F0	/* regular sample buffer */
+#define ENE_SAMPLE_SPC_MASK	0x80	/* sample is space */
+#define ENE_SAMPLE_VALUE_MASK	0x7F
+#define ENE_SAMPLE_OVERFLOW	0x7F
+#define ENE_SAMPLES_SIZE	4
+
+/* fan input sample buffer */
+#define ENE_SAMPLE_BUFFER_FAN	0xF8FB	/* this buffer holds high byte of */
+					/* each sample of normal buffer */
+#define ENE_FAN_SMPL_PULS_MSK	0x8000	/* this bit of combined sample */
+					/* if set, says that sample is pulse */
+#define ENE_FAN_VALUE_MASK	0x0FFF  /* mask for valid bits of the value */
+
+/* first firmware register */
+#define ENE_FW1			0xF8F8
+#define	ENE_FW1_ENABLE		0x01	/* enable fw processing */
+#define ENE_FW1_TXIRQ		0x02	/* TX interrupt pending */
+#define ENE_FW1_WAKE		0x40	/* enable wake from S3 */
+#define ENE_FW1_IRQ		0x80	/* enable interrupt */
+
+/* second firmware register */
+#define ENE_FW2			0xF8F9
+#define ENE_FW2_BUF_HIGH	0x01	/* which half of the buffer to read */
+#define ENE_FW2_IRQ_CLR		0x04	/* clear this on IRQ */
+#define ENE_FW2_GP40_AS_LEARN	0x08	/* normal input is used as */
+					/* learning input */
+#define ENE_FW2_FAN_AS_NRML_IN	0x40	/* fan is used as normal input */
+#define ENE_FW2_LEARNING	0x80	/* hardware supports learning and TX */
+
+/* transmitter ports */
+#define ENE_TX_PORT2		0xFC01	/* this enables one or both */
+#define ENE_TX_PORT2_EN		0x20	/* TX ports */
+#define ENE_TX_PORT1		0xFC08
+#define ENE_TX_PORT1_EN		0x02
+
+/* IRQ registers block (for revision B) */
+#define ENEB_IRQ		0xFD09	/* IRQ number */
+#define ENEB_IRQ_UNK1		0xFD17	/* unknown setting = 1 */
+#define ENEB_IRQ_STATUS		0xFD80	/* irq status */
+#define ENEB_IRQ_STATUS_IR	0x20	/* IR irq */
+
+/* fan as input settings - only if learning capable */
+#define ENE_FAN_AS_IN1		0xFE30  /* fan init reg 1 */
+#define ENE_FAN_AS_IN1_EN	0xCD
+#define ENE_FAN_AS_IN2		0xFE31  /* fan init reg 2 */
+#define ENE_FAN_AS_IN2_EN	0x03
+#define ENE_SAMPLE_PERIOD_FAN   61	/* fan input has fixed sample period */
+
+/* IRQ registers block (for revision C,D) */
+#define ENEC_IRQ		0xFE9B	/* new irq settings register */
+#define ENEC_IRQ_MASK		0x0F	/* irq number mask */
+#define ENEC_IRQ_UNK_EN		0x10	/* always enabled */
+#define ENEC_IRQ_STATUS		0x20	/* irq status and ACK */
+
+/* CIR block settings */
+#define ENE_CIR_CONF1		0xFEC0
+#define ENE_CIR_CONF1_TX_CLEAR	0x01	/* clear that on revC */
+					/* while transmitting */
+#define ENE_CIR_CONF1_RX_ON	0x07	/* normal reciever enabled */
+#define ENE_CIR_CONF1_LEARN1	0x08	/* enabled on learning mode */
+#define ENE_CIR_CONF1_TX_ON	0x30	/* enabled on transmit */
+#define ENE_CIR_CONF1_TX_CARR	0x80	/* send TX carrier or not */
+
+#define ENE_CIR_CONF2		0xFEC1	/* unknown setting = 0 */
+#define ENE_CIR_CONF2_LEARN2	0x10	/* set on enable learning */
+#define ENE_CIR_CONF2_GPIO40DIS	0x20	/* disable input via gpio40 */
+
+#define ENE_CIR_SAMPLE_PERIOD	0xFEC8	/* sample period in us */
+#define ENE_CIR_SAMPLE_OVERFLOW	0x80	/* interrupt on overflows if set */
+
+
+/* Two byte tx buffer */
+#define ENE_TX_INPUT1		0xFEC9
+#define ENE_TX_INPUT2		0xFECA
+#define ENE_TX_PULSE_MASK	0x80	/* Transmitted sample is pulse */
+#define ENE_TX_SMLP_MASK	0x7F
+#define ENE_TX_SMPL_PERIOD	50	/* transmit sample period - fixed */
+
+
+/* Unknown TX setting - TX sample period ??? */
+#define ENE_TX_UNK1		0xFECB	/* set to 0x63 */
+
+/* Current recieved carrier period */
+#define ENE_RX_CARRIER		0xFECC	/* RX period (500 ns) */
+#define ENE_RX_CARRIER_VALID	0x80	/* Register content valid */
+
+
+/* TX period (1/carrier) */
+#define ENE_TX_PERIOD		0xFECE	/* TX period (500 ns) */
+#define ENE_TX_PERIOD_UNKBIT	0x80	/* This bit set on transmit*/
+#define ENE_TX_PERIOD_PULSE	0xFECF	/* TX pulse period (500 ns)*/
+
+/* Hardware versions */
+#define ENE_HW_VERSION		0xFF00	/* hardware revision */
+#define ENE_HW_UNK		0xFF1D
+#define ENE_HW_UNK_CLR		0x04
+#define ENE_HW_VER_MAJOR	0xFF1E	/* chip version */
+#define ENE_HW_VER_MINOR	0xFF1F
+#define ENE_HW_VER_OLD		0xFD00
+
+/* Normal/Learning carrier ranges - only valid if we have learning input*/
+/* TODO: test */
+#define ENE_NORMAL_RX_LOW	34
+#define ENE_NORMAL_RX_HI	38
+
+/* Tx carrier range */
+/* Hardware might be able to do more, but this range is enough for
+   all purposes */
+#define ENE_TX_PERIOD_MAX	32	/* corresponds to 29.4 kHz */
+#define ENE_TX_PERIOD_MIN	16	/* corrsponds to 62.5 kHz */
+
+
+
+/* Minimal and maximal gaps */
+
+/* Normal case:
+	Minimal gap is 0x7F * sample period
+	Maximum gap depends on hardware.
+	For KB3926B, it is unlimited, for newer models its around
+	250000, after which HW stops sending samples, and that is
+	not possible to change */
+
+/* Fan case:
+	Both minimal and maximal gaps are same, and equal to 0xFFF * 0x61
+	And there is nothing to change this setting
+*/
+
+#define ENE_MAXGAP		250000
+#define ENE_MINGAP		(127 * sample_period)
+
+/******************************************************************************/
+
+#define ENE_DRIVER_NAME		"enecir"
+#define ENE_TXBUF_SIZE (500 * sizeof(int))	/* 500 samples (arbitary) */
+
+#define ENE_IRQ_RX		1
+#define ENE_IRQ_TX		2
+
+#define  ENE_HW_B		1	/* 3926B */
+#define  ENE_HW_C		2	/* 3926C */
+#define  ENE_HW_D		3	/* 3926D */
+
+#define ene_printk(level, text, ...) \
+	printk(level ENE_DRIVER_NAME ": " text, ## __VA_ARGS__)
+
+#define ene_dbg(text, ...) \
+	if (debug) \
+		printk(KERN_DEBUG \
+			ENE_DRIVER_NAME ": " text "\n" , ## __VA_ARGS__)
+
+#define ene_dbg_verbose(text, ...) \
+	if (debug > 1) \
+		printk(KERN_DEBUG \
+			ENE_DRIVER_NAME ": " text "\n" , ## __VA_ARGS__)
+
+
+struct ene_device {
+	struct pnp_dev *pnp_dev;
+	struct lirc_driver *lirc_driver;
+	int in_use;
+
+	/* hw IO settings */
+	unsigned long hw_io;
+	int irq;
+	spinlock_t hw_lock;
+
+	/* HW features */
+	int hw_revision;			/* hardware revision */
+	int hw_learning_and_tx_capable;		/* learning capable */
+	int hw_gpio40_learning;			/* gpio40 is learning */
+	int hw_fan_as_normal_input;		/* fan input is used as */
+						/* regular input */
+	/* HW state*/
+	int rx_pointer;				/* hw pointer to rx buffer */
+	int rx_fan_input_inuse;			/* is fan input in use for rx*/
+	int tx_reg;				/* current reg used for TX */
+	u8  saved_conf1;			/* saved FEC0 reg */
+	int learning_enabled;			/* learning input enabled */
+
+	/* RX sample handling */
+	int rx_sample;				/* current recieved sample */
+	int rx_sample_pulse;			/* recieved sample is pulse */
+	int rx_idle;				/* idle mode for RX activated */
+	struct timeval rx_gap_start;		/* time of start of idle */
+	int rx_timeout;				/* time in ms of RX timeout */
+	int rx_send_timeout_packet;		/* do we send RX timeout */
+	int rx_timeout_sent;			/* we sent the timeout packet */
+	int rx_carrier_sense;			/* sense carrier */
+
+	/* TX sample handling */
+	unsigned int tx_sample;			/* current sample for TX */
+	int tx_sample_pulse;			/* current sample is pulse */
+
+	/* TX buffer */
+	int tx_buffer[ENE_TXBUF_SIZE];		/* input samples buffer*/
+	int tx_pos;				/* position in that bufer */
+	int tx_len;				/* current len of tx buffer */
+	int tx_underway;			/* TX is under way*/
+	int tx_done;				/* done transmitting */
+						/* one more sample pending*/
+	struct completion tx_complete;		/* TX completion */
+	struct timer_list tx_sim_timer;
+
+	/*TX settings */
+	int tx_period;
+	int tx_duty_cycle;
+	int transmitter_mask;
+};

drivers/staging/lirc/Kconfig

@@ -18,14 +18,6 @@ config LIRC_BT829
 	help
 	  Driver for the IR interface on BT829-based hardware
 
-config LIRC_ENE0100
-	tristate "ENE KB3924/ENE0100 CIR Port Reciever"
-	depends on LIRC_STAGING && PNP
-	help
-	  This is a driver for CIR port handled by ENE KB3924 embedded
-	  controller found on some notebooks.
-	  It appears on PNP list as ENE0100.
-
 config LIRC_I2C
 	tristate "I2C Based IR Receivers"
 	depends on LIRC_STAGING && I2C

drivers/staging/lirc/Makefile

@@ -4,7 +4,6 @@
 # Each configuration option enables a list of files.
 
 obj-$(CONFIG_LIRC_BT829)	+= lirc_bt829.o
-obj-$(CONFIG_LIRC_ENE0100)	+= lirc_ene0100.o
 obj-$(CONFIG_LIRC_I2C)		+= lirc_i2c.o
 obj-$(CONFIG_LIRC_IGORPLUGUSB)	+= lirc_igorplugusb.o
 obj-$(CONFIG_LIRC_IMON)		+= lirc_imon.o