staging: rtl8192e: Remove unused defines

Remove most of unused defines (excluding phyreg/hw registers).
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drivers/staging/rtl8192e/dot11d.h

@@ -79,7 +79,6 @@ static inline void cpMacAddr(unsigned char *des, unsigned char *src)
 #define UPDATE_CIE_SRC(__pIeeeDev, __pTa)		\
 	cpMacAddr(GET_DOT11D_INFO(__pIeeeDev)->CountryIeSrcAddr, __pTa)
 
-#define CIE_WATCHDOG_TH 1
 #define GET_CIE_WATCHDOG(__pIeeeDev)				\
 	 (GET_DOT11D_INFO(__pIeeeDev)->CountryIeWatchdog)
 static inline void RESET_CIE_WATCHDOG(struct rtllib_device *__pIeeeDev)
@@ -88,9 +87,6 @@ static inline void RESET_CIE_WATCHDOG(struct rtllib_device *__pIeeeDev)
 }
 #define UPDATE_CIE_WATCHDOG(__pIeeeDev) (++GET_CIE_WATCHDOG(__pIeeeDev))
 
-#define IS_DOT11D_STATE_DONE(__pIeeeDev)			\
-	(GET_DOT11D_INFO(__pIeeeDev)->State == DOT11D_STATE_DONE)
-
 void dot11d_init(struct rtllib_device *dev);
 void Dot11d_Channelmap(u8 channel_plan, struct rtllib_device *ieee);
 void Dot11d_Reset(struct rtllib_device *dev);

drivers/staging/rtl8192e/rtl8192e/r8190P_def.h

@@ -26,8 +26,6 @@
 #define		MAX_SILENT_RESET_RX_SLOT_NUM	10
 
 #define RX_MPDU_QUEUE				0
-#define RX_CMD_QUEUE				1
-
 
 enum rtl819x_loopback {
 	RTL819X_NO_LOOPBACK = 0,
@@ -36,11 +34,6 @@ enum rtl819x_loopback {
 	RTL819X_CCK_LOOPBACK = 3,
 };
 
-
-#define RESET_DELAY_8185			20
-
-#define RT_IBSS_INT_MASKS (IMR_BcnInt | IMR_BcnInt | IMR_TBDOK | IMR_TBDER)
-
 #define DESC90_RATE1M				0x00
 #define DESC90_RATE2M				0x01
 #define DESC90_RATE5_5M				0x02
@@ -74,17 +67,6 @@ enum rtl819x_loopback {
 #define SHORT_SLOT_TIME				9
 #define NON_SHORT_SLOT_TIME		20
 
-
-#define	MAX_LINES_HWCONFIG_TXT			1000
-#define MAX_BYTES_LINE_HWCONFIG_TXT		128
-
-#define SW_THREE_WIRE			0
-#define HW_THREE_WIRE			2
-
-#define BT_DEMO_BOARD			0
-#define BT_QA_BOARD				1
-#define BT_FPGA					2
-
 #define	RX_SMOOTH				20
 
 #define QSLT_BK					0x1
@@ -96,25 +78,14 @@ enum rtl819x_loopback {
 #define	QSLT_MGNT				0x12
 #define	QSLT_CMD				0x13
 
-#define NUM_OF_FIRMWARE_QUEUE				10
-#define NUM_OF_PAGES_IN_FW					0x100
 #define NUM_OF_PAGE_IN_FW_QUEUE_BK		0x007
 #define NUM_OF_PAGE_IN_FW_QUEUE_BE		0x0aa
 #define NUM_OF_PAGE_IN_FW_QUEUE_VI		0x024
 #define NUM_OF_PAGE_IN_FW_QUEUE_VO		0x007
-#define NUM_OF_PAGE_IN_FW_QUEUE_HCCA		0
-#define NUM_OF_PAGE_IN_FW_QUEUE_CMD		0x2
 #define NUM_OF_PAGE_IN_FW_QUEUE_MGNT		0x10
-#define NUM_OF_PAGE_IN_FW_QUEUE_HIGH		0
 #define NUM_OF_PAGE_IN_FW_QUEUE_BCN		0x4
 #define NUM_OF_PAGE_IN_FW_QUEUE_PUB		0xd
 
-#define NUM_OF_PAGE_IN_FW_QUEUE_BK_DTM	0x026
-#define NUM_OF_PAGE_IN_FW_QUEUE_BE_DTM	0x048
-#define NUM_OF_PAGE_IN_FW_QUEUE_VI_DTM	0x048
-#define NUM_OF_PAGE_IN_FW_QUEUE_VO_DTM	0x026
-#define NUM_OF_PAGE_IN_FW_QUEUE_PUB_DTM	0x00
-
 #define APPLIED_RESERVED_QUEUE_IN_FW		0x80000000
 #define RSVD_FW_QUEUE_PAGE_BK_SHIFT		0x00
 #define RSVD_FW_QUEUE_PAGE_BE_SHIFT		0x08
@@ -197,23 +168,6 @@ struct tx_fwinfo_8190pci {
 
 };
 
-
-#define TX_DESC_SIZE			32
-
-#define TX_DESC_CMD_SIZE	32
-
-
-#define TX_STATUS_DESC_SIZE	32
-
-#define TX_FWINFO_SIZE	8
-
-
-#define RX_DESC_SIZE	16
-
-#define RX_STATUS_DESC_SIZE	16
-
-#define RX_DRIVER_INFO_SIZE	8
-
 struct log_int_8190 {
 	u32	nIMR_COMDOK;
 	u32	nIMR_MGNTDOK;

drivers/staging/rtl8192e/rtl8192e/r8192E_firmware.h

@@ -19,8 +19,6 @@
 #ifndef __INC_FIRMWARE_H
 #define __INC_FIRMWARE_H
 
-#define RTL8190_CPU_START_OFFSET	0x80
-
 #define GET_COMMAND_PACKET_FRAG_THRESHOLD(v)	(4*(v/4) - 8)
 
 #define RTL8192E_BOOT_IMG_FW	"RTL8192E/boot.img"

drivers/staging/rtl8192e/rtl8192e/rtl_dm.c

@@ -58,9 +58,6 @@ static u32 edca_setting_UL[HT_IOT_PEER_MAX] = {
 	0x5e4332
 };
 
-#define RTK_UL_EDCA 0xa44f
-#define RTK_DL_EDCA 0x5e4322
-
 const u32 dm_tx_bb_gain[TxBBGainTableLength] = {
 	0x7f8001fe, /* 12 dB */
 	0x788001e2, /* 11 dB */

drivers/staging/rtl8192e/rtl8192e/rtl_dm.h

@@ -27,26 +27,17 @@
 #define		DM_DIG_THRESH_HIGH					40
 #define		DM_DIG_THRESH_LOW					35
 
-#define		DM_FALSEALARM_THRESH_LOW	40
-#define		DM_FALSEALARM_THRESH_HIGH	1000
-
 #define		DM_DIG_HIGH_PWR_THRESH_HIGH		75
 #define		DM_DIG_HIGH_PWR_THRESH_LOW		70
 
 #define		BW_AUTO_SWITCH_HIGH_LOW			25
 #define		BW_AUTO_SWITCH_LOW_HIGH			30
 
-#define		DM_check_fsync_time_interval				500
-
-
 #define		DM_DIG_BACKOFF				12
 #define		DM_DIG_MAX					0x36
 #define		DM_DIG_MIN					0x1c
 #define		DM_DIG_MIN_Netcore			0x12
 
-#define		DM_DIG_BACKOFF_MAX			12
-#define		DM_DIG_BACKOFF_MIN			-4
-
 #define		RxPathSelection_SS_TH_low		30
 #define		RxPathSelection_diff_TH			18
 
@@ -55,8 +46,6 @@
 #define		RateAdaptiveTH_Low_40M		10
 #define		VeryLowRSSI					15
 
-#define		CTSToSelfTHVal					35
-
 #define		WAIotTHVal						25
 
 #define		E_FOR_TX_POWER_TRACK	       300
@@ -70,14 +59,6 @@
 #define			Tx_Retry_Count_Reg	 0x1ac
 #define		RegC38_TH				 20
 
-#define		TX_POWER_NEAR_FIELD_THRESH_LVL2	74
-#define		TX_POWER_NEAR_FIELD_THRESH_LVL1	67
-
-#define		TxHighPwrLevel_Normal		0
-#define		TxHighPwrLevel_Level1		1
-#define		TxHighPwrLevel_Level2		2
-
-#define		DM_Type_ByFW			0
 #define		DM_Type_ByDriver		1
 
 /*--------------------------Define Parameters-------------------------------*/

drivers/staging/rtl8192e/rtl8192e/rtl_ps.h

@@ -30,7 +30,6 @@
 struct net_device;
 
 #define RT_CHECK_FOR_HANG_PERIOD 2
-#define INIT_DEFAULT_CHAN	 1
 
 void rtl8192_hw_wakeup(struct net_device *dev);
 void rtl8192_hw_to_sleep(struct net_device *dev, u64 time);

drivers/staging/rtl8192e/rtl8192e/rtl_wx.c

@@ -729,9 +729,6 @@ static int r8192_wx_set_enc(struct net_device *dev,
 			hwkey[i] |= (key[4 * i + 3] & mask) << 24;
 		}
 
-		#define CONF_WEP40  0x4
-		#define CONF_WEP104 0x14
-
 		switch (wrqu->encoding.flags & IW_ENCODE_INDEX) {
 		case 0:
 			key_idx = ieee->crypt_info.tx_keyidx;

drivers/staging/rtl8192e/rtl819x_BA.h

@@ -19,11 +19,7 @@
 #ifndef _BATYPE_H_
 #define _BATYPE_H_
 
-#define		TOTAL_TXBA_NUM	16
-#define	TOTAL_RXBA_NUM	16
-
 #define	BA_SETUP_TIMEOUT	200
-#define	BA_INACT_TIMEOUT	60000
 
 #define	BA_POLICY_DELAYED		0
 #define	BA_POLICY_IMMEDIATE	1
@@ -32,7 +28,6 @@
 #define	ADDBA_STATUS_REFUSED		37
 #define	ADDBA_STATUS_INVALID_PARAM	38
 
-#define	DELBA_REASON_QSTA_LEAVING	36
 #define	DELBA_REASON_END_BA			37
 #define	DELBA_REASON_UNKNOWN_BA	38
 #define	DELBA_REASON_TIMEOUT			39

drivers/staging/rtl8192e/rtl819x_HT.h

@@ -20,8 +20,6 @@
 #define _RTL819XU_HTTYPE_H_
 
 #define MIMO_PS_STATIC				0
-#define MIMO_PS_DYNAMIC			1
-#define MIMO_PS_NOLIMIT			3
 
 #define sHTCLng	4
 

drivers/staging/rtl8192e/rtl819x_TS.h

@@ -19,8 +19,6 @@
 #ifndef _TSTYPE_H_
 #define _TSTYPE_H_
 #include "rtl819x_Qos.h"
-#define TS_SETUP_TIMEOUT	60
-#define TS_INACT_TIMEOUT	60
 #define TS_ADDBA_DELAY		60
 
 #define TOTAL_TS_NUM		16

drivers/staging/rtl8192e/rtllib.h

@@ -84,9 +84,6 @@
 #define iwe_stream_add_point_rsl(info, start, stop, iwe, p)	\
 	iwe_stream_add_point(info, start, stop, iwe, p)
 
-#define usb_alloc_urb_rsl(x, y) usb_alloc_urb(x, y)
-#define usb_submit_urb_rsl(x, y) usb_submit_urb(x, y)
-
 static inline void *netdev_priv_rsl(struct net_device *dev)
 {
 	return netdev_priv(dev);
@@ -110,27 +107,14 @@ static inline void *netdev_priv_rsl(struct net_device *dev)
 #define HIGH_QUEUE			     7
 #define BEACON_QUEUE			   8
 
-#define LOW_QUEUE			      BE_QUEUE
-#define NORMAL_QUEUE			   MGNT_QUEUE
-
 #ifndef IW_MODE_MESH
 #define IW_MODE_MESH			7
 #endif
-#define AMSDU_SUBHEADER_LEN 14
-#define SWRF_TIMEOUT				50
 
 #define IE_CISCO_FLAG_POSITION		0x08
 #define SUPPORT_CKIP_MIC			0x08
 #define SUPPORT_CKIP_PK			0x10
-#define	RT_RF_OFF_LEVL_ASPM			BIT0
-#define	RT_RF_OFF_LEVL_CLK_REQ		BIT1
-#define	RT_RF_OFF_LEVL_PCI_D3			BIT2
 #define	RT_RF_OFF_LEVL_HALT_NIC		BIT3
-#define	RT_RF_OFF_LEVL_FREE_FW		BIT4
-#define	RT_RF_OFF_LEVL_FW_32K		BIT5
-#define	RT_RF_PS_LEVEL_ALWAYS_ASPM	BIT6
-#define	RT_RF_LPS_DISALBE_2R			BIT30
-#define	RT_RF_LPS_LEVEL_ASPM			BIT31
 #define	RT_IN_PS_LEVEL(pPSC, _PS_FLAG)		\
 	((pPSC->CurPsLevel & _PS_FLAG) ? true : false)
 #define	RT_CLEAR_PS_LEVEL(pPSC, _PS_FLAG)	\
@@ -244,22 +228,6 @@ struct sw_chnl_cmd {
 #define MGN_MCS13	       0x8d
 #define MGN_MCS14	       0x8e
 #define MGN_MCS15	       0x8f
-#define	MGN_MCS0_SG			0x90
-#define	MGN_MCS1_SG			0x91
-#define	MGN_MCS2_SG			0x92
-#define	MGN_MCS3_SG			0x93
-#define	MGN_MCS4_SG			0x94
-#define	MGN_MCS5_SG			0x95
-#define	MGN_MCS6_SG			0x96
-#define	MGN_MCS7_SG			0x97
-#define	MGN_MCS8_SG			0x98
-#define	MGN_MCS9_SG			0x99
-#define	MGN_MCS10_SG		0x9a
-#define	MGN_MCS11_SG		0x9b
-#define	MGN_MCS12_SG		0x9c
-#define	MGN_MCS13_SG		0x9d
-#define	MGN_MCS14_SG		0x9e
-#define	MGN_MCS15_SG		0x9f
 
 enum hw_variables {
 	HW_VAR_ETHER_ADDR,
@@ -748,16 +716,11 @@ struct rtllib_stats {
 
 struct rtllib_device;
 
-#define SEC_KEY_1	 (1<<0)
-#define SEC_KEY_2	 (1<<1)
-#define SEC_KEY_3	 (1<<2)
-#define SEC_KEY_4	 (1<<3)
 #define SEC_ACTIVE_KEY    (1<<4)
 #define SEC_AUTH_MODE     (1<<5)
 #define SEC_UNICAST_GROUP (1<<6)
 #define SEC_LEVEL	 (1<<7)
 #define SEC_ENABLED       (1<<8)
-#define SEC_ENCRYPT       (1<<9)
 
 #define SEC_LEVEL_0      0 /* None */
 #define SEC_LEVEL_1      1 /* WEP 40 and 104 bit */
@@ -772,7 +735,6 @@ struct rtllib_device;
 
 #define WEP_KEY_LEN		13
 #define SCM_KEY_LEN		32
-#define SCM_TEMPORAL_KEY_LENGTH 16
 
 struct rtllib_security {
 	u16 active_key:2,
@@ -1187,8 +1149,6 @@ enum {WMM_all_frame, WMM_two_frame, WMM_four_frame, WMM_six_frame};
 #define WME_AC_BE   0x01
 #define WME_AC_VI   0x02
 #define WME_AC_VO   0x03
-#define WME_ACI_MASK 0x03
-#define WME_AIFSN_MASK 0x03
 #define WME_AC_PRAM_LEN 16
 
 #define MAX_RECEIVE_BUFFER_SIZE 9100

drivers/staging/rtl8192e/rtllib_softmac.c

@@ -1511,7 +1511,6 @@ static void rtllib_associate_step2(struct rtllib_device *ieee)
 	}
 }
 
-#define CANCELLED  2
 static void rtllib_associate_complete_wq(void *data)
 {
 	struct rtllib_device *ieee = (struct rtllib_device *)