tty: serial: 8250: Suitably replace printk

This patch replaces printk by the corresponding variant of dev_* in order
to fix checkpatch warnings. If no suitable device pointer is present, the
corresponding pr_* variant is used.
Signed-off-by: Phillip Raffeck <phillip.raffeck@fau.de>
Signed-off-by: Anton Würfel <anton.wuerfel@fau.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: linux-kernel@i4.cs.fau.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drivers/tty/serial/8250/8250_core.c

@@ -1099,9 +1099,8 @@ static int __init serial8250_init(void)
 
 	serial8250_isa_init_ports();
 
-	printk(KERN_INFO "Serial: 8250/16550 driver, "
-		"%d ports, IRQ sharing %sabled\n", nr_uarts,
-		share_irqs ? "en" : "dis");
+	pr_info("Serial: 8250/16550 driver, %d ports, IRQ sharing %sabled\n",
+		nr_uarts, share_irqs ? "en" : "dis");
 
 #ifdef CONFIG_SPARC
 	ret = sunserial_register_minors(&serial8250_reg, UART_NR);

drivers/tty/serial/8250/8250_gsc.c

@@ -42,7 +42,7 @@ static int __init serial_init_chip(struct parisc_device *dev)
 		 * the user what they're missing.
 		 */
 		if (parisc_parent(dev)->id.hw_type != HPHW_IOA)
-			printk(KERN_INFO
+			dev_info(&dev->dev,
 				"Serial: device 0x%llx not configured.\n"
 				"Enable support for Wax, Lasi, Asp or Dino.\n",
 				(unsigned long long)dev->hpa.start);
@@ -66,8 +66,9 @@ static int __init serial_init_chip(struct parisc_device *dev)
 
 	err = serial8250_register_8250_port(&uart);
 	if (err < 0) {
-		printk(KERN_WARNING
-			"serial8250_register_8250_port returned error %d\n", err);
+		dev_warn(&dev->dev,
+			"serial8250_register_8250_port returned error %d\n",
+			err);
 		iounmap(uart.port.membase);
 		return err;
 	}

drivers/tty/serial/8250/8250_hp300.c

@@ -110,7 +110,7 @@ int __init hp300_setup_serial_console(void)
 	/* Check for APCI console */
 	if (scode == 256) {
 #ifdef CONFIG_HPAPCI
-		printk(KERN_INFO "Serial console is HP APCI 1\n");
+		pr_info("Serial console is HP APCI 1\n");
 
 		port.uartclk = HPAPCI_BAUD_BASE * 16;
 		port.mapbase = (FRODO_BASE + FRODO_APCI_OFFSET(1));
@@ -118,7 +118,7 @@ int __init hp300_setup_serial_console(void)
 		port.regshift = 2;
 		add_preferred_console("ttyS", port.line, "9600n8");
 #else
-		printk(KERN_WARNING "Serial console is APCI but support is disabled (CONFIG_HPAPCI)!\n");
+		pr_warn("Serial console is APCI but support is disabled (CONFIG_HPAPCI)!\n");
 		return 0;
 #endif
 	} else {
@@ -127,7 +127,7 @@ int __init hp300_setup_serial_console(void)
 		if (!pa)
 			return 0;
 
-		printk(KERN_INFO "Serial console is HP DCA at select code %d\n", scode);
+		pr_info("Serial console is HP DCA at select code %d\n", scode);
 
 		port.uartclk = HPDCA_BAUD_BASE * 16;
 		port.mapbase = (pa + UART_OFFSET);
@@ -141,13 +141,13 @@ int __init hp300_setup_serial_console(void)
 		if (DIO_ID(pa + DIO_VIRADDRBASE) & 0x80)
 			add_preferred_console("ttyS", port.line, "9600n8");
 #else
-		printk(KERN_WARNING "Serial console is DCA but support is disabled (CONFIG_HPDCA)!\n");
+		pr_warn("Serial console is DCA but support is disabled (CONFIG_HPDCA)!\n");
 		return 0;
 #endif
 	}
 
 	if (early_serial_setup(&port) < 0)
-		printk(KERN_WARNING "hp300_setup_serial_console(): early_serial_setup() failed.\n");
+		pr_warn("%s: early_serial_setup() failed.\n", __func__);
 	return 0;
 }
 #endif /* CONFIG_SERIAL_8250_CONSOLE */
@@ -179,8 +179,9 @@ static int hpdca_init_one(struct dio_dev *d,
 	line = serial8250_register_8250_port(&uart);
 
 	if (line < 0) {
-		printk(KERN_NOTICE "8250_hp300: register_serial() DCA scode %d"
-		       " irq %d failed\n", d->scode, uart.port.irq);
+		dev_notice(&d->dev,
+			  "8250_hp300: register_serial() DCA scode %d irq %d failed\n",
+			  d->scode, uart.port.irq);
 		return -ENOMEM;
 	}
 
@@ -260,8 +261,9 @@ static int __init hp300_8250_init(void)
 		line = serial8250_register_8250_port(&uart);
 
 		if (line < 0) {
-			printk(KERN_NOTICE "8250_hp300: register_serial() APCI"
-			       " %d irq %d failed\n", i, uart.port.irq);
+			dev_notice(uart.port.dev,
+				   "8250_hp300: register_serial() APCI %d irq %d failed\n",
+				   i, uart.port.irq);
 			kfree(port);
 			continue;
 		}

drivers/tty/serial/8250/8250_port.c

@@ -1316,8 +1316,7 @@ static void autoconfig(struct uart_8250_port *up)
 out_lock:
 	spin_unlock_irqrestore(&port->lock, flags);
 	if (up->capabilities != old_capabilities) {
-		printk(KERN_WARNING
-		       "ttyS%d: detected caps %08x should be %08x\n",
+		pr_warn("ttyS%d: detected caps %08x should be %08x\n",
 		       serial_index(port), old_capabilities,
 		       up->capabilities);
 	}