Merge branch 'dm9051'

Joseph CHAMG says:

====================
ADD DM9051 ETHERNET DRIVER

DM9051 is a spi interface chip,
need cs/mosi/miso/clock with an interrupt gpio pin
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Documentation/devicetree/bindings/net/davicom,dm9051.yaml

+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/net/davicom,dm9051.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Davicom DM9051 SPI Ethernet Controller
+
+maintainers:
+  - Joseph CHANG <josright123@gmail.com>
+
+description: |
+  The DM9051 is a fully integrated and cost-effective low pin count single
+  chip Fast Ethernet controller with a Serial Peripheral Interface (SPI).
+
+allOf:
+  - $ref: ethernet-controller.yaml#
+
+properties:
+  compatible:
+    const: davicom,dm9051
+
+  reg:
+    maxItems: 1
+
+  spi-max-frequency:
+    maximum: 45000000
+
+  interrupts:
+    maxItems: 1
+
+  local-mac-address: true
+
+  mac-address: true
+
+required:
+  - compatible
+  - reg
+  - spi-max-frequency
+  - interrupts
+
+additionalProperties: false
+
+examples:
+  # Raspberry Pi platform
+  - |
+    /* for Raspberry Pi with pin control stuff for GPIO irq */
+    #include <dt-bindings/interrupt-controller/irq.h>
+    #include <dt-bindings/gpio/gpio.h>
+    spi {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        ethernet@0 {
+            compatible = "davicom,dm9051";
+            reg = <0>; /* spi chip select */
+            local-mac-address = [00 00 00 00 00 00];
+            interrupt-parent = <&gpio>;
+            interrupts = <26 IRQ_TYPE_LEVEL_LOW>;
+            spi-max-frequency = <31200000>;
+        };
+    };

drivers/net/ethernet/davicom/Kconfig

@@ -3,6 +3,19 @@
 # Davicom device configuration
 #
 
+config NET_VENDOR_DAVICOM
+	bool "Davicom devices"
+	default y
+	help
+	  If you have a network (Ethernet) card belonging to this class, say Y.
+
+	  Note that the answer to this question doesn't directly affect the
+	  kernel: saying N will just cause the configurator to skip all
+	  the questions about Davicom devices. If you say Y, you will be asked
+	  for your specific card in the following selections.
+
+if NET_VENDOR_DAVICOM
+
 config DM9000
 	tristate "DM9000 support"
 	depends on ARM || MIPS || COLDFIRE || NIOS2 || COMPILE_TEST
@@ -22,3 +35,21 @@ config DM9000_FORCE_SIMPLE_PHY_POLL
 	  bit to determine if the link is up or down instead of the more
 	  costly MII PHY reads. Note, this will not work if the chip is
 	  operating with an external PHY.
+
+config DM9051
+	tristate "DM9051 SPI support"
+	depends on SPI
+	select CRC32
+	select MDIO
+	select PHYLIB
+	select REGMAP_SPI
+	help
+	  Support for DM9051 SPI chipset.
+
+	  To compile this driver as a module, choose M here.  The module
+	  will be called dm9051.
+
+	  The SPI mode for the host's SPI master to access DM9051 is mode
+	  0 on the SPI bus.
+
+endif # NET_VENDOR_DAVICOM

drivers/net/ethernet/davicom/Makefile

@@ -4,3 +4,4 @@
 #
 
 obj-$(CONFIG_DM9000) += dm9000.o
+obj-$(CONFIG_DM9051) += dm9051.o

drivers/net/ethernet/davicom/dm9051.h

+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Copyright (c) 2022 Davicom Semiconductor,Inc.
+ * Davicom DM9051 SPI Fast Ethernet Linux driver
+ */
+
+#ifndef _DM9051_H_
+#define _DM9051_H_
+
+#include <linux/bits.h>
+#include <linux/netdevice.h>
+#include <linux/types.h>
+
+#define DM9051_ID		0x9051
+
+#define DM9051_NCR		0x00
+#define DM9051_NSR		0x01
+#define DM9051_TCR		0x02
+#define DM9051_RCR		0x05
+#define DM9051_BPTR		0x08
+#define DM9051_FCR		0x0A
+#define DM9051_EPCR		0x0B
+#define DM9051_EPAR		0x0C
+#define DM9051_EPDRL		0x0D
+#define DM9051_EPDRH		0x0E
+#define DM9051_PAR		0x10
+#define DM9051_MAR		0x16
+#define DM9051_GPCR		0x1E
+#define DM9051_GPR		0x1F
+
+#define DM9051_VIDL		0x28
+#define DM9051_VIDH		0x29
+#define DM9051_PIDL		0x2A
+#define DM9051_PIDH		0x2B
+#define DM9051_SMCR		0x2F
+#define	DM9051_ATCR		0x30
+#define	DM9051_SPIBCR		0x38
+#define DM9051_INTCR		0x39
+#define DM9051_PPCR		0x3D
+
+#define DM9051_MPCR		0x55
+#define DM9051_LMCR		0x57
+#define DM9051_MBNDRY		0x5E
+
+#define DM9051_MRRL		0x74
+#define DM9051_MRRH		0x75
+#define DM9051_MWRL		0x7A
+#define DM9051_MWRH		0x7B
+#define DM9051_TXPLL		0x7C
+#define DM9051_TXPLH		0x7D
+#define DM9051_ISR		0x7E
+#define DM9051_IMR		0x7F
+
+#define DM_SPI_MRCMDX		0x70
+#define DM_SPI_MRCMD		0x72
+#define DM_SPI_MWCMD		0x78
+
+#define DM_SPI_WR		0x80
+
+/* dm9051 Ethernet controller registers bits
+ */
+/* 0x00 */
+#define NCR_WAKEEN		BIT(6)
+#define NCR_FDX			BIT(3)
+#define NCR_RST			BIT(0)
+/* 0x01 */
+#define NSR_SPEED		BIT(7)
+#define NSR_LINKST		BIT(6)
+#define NSR_WAKEST		BIT(5)
+#define NSR_TX2END		BIT(3)
+#define NSR_TX1END		BIT(2)
+/* 0x02 */
+#define TCR_DIS_JABBER_TIMER	BIT(6) /* for Jabber Packet support */
+#define TCR_TXREQ		BIT(0)
+/* 0x05 */
+#define RCR_DIS_WATCHDOG_TIMER	BIT(6)  /* for Jabber Packet support */
+#define RCR_DIS_LONG		BIT(5)
+#define RCR_DIS_CRC		BIT(4)
+#define RCR_ALL			BIT(3)
+#define RCR_PRMSC		BIT(1)
+#define RCR_RXEN		BIT(0)
+#define RCR_RX_DISABLE		(RCR_DIS_LONG | RCR_DIS_CRC)
+/* 0x06 */
+#define RSR_RF			BIT(7)
+#define RSR_MF			BIT(6)
+#define RSR_LCS			BIT(5)
+#define RSR_RWTO		BIT(4)
+#define RSR_PLE			BIT(3)
+#define RSR_AE			BIT(2)
+#define RSR_CE			BIT(1)
+#define RSR_FOE			BIT(0)
+#define	RSR_ERR_BITS		(RSR_RF | RSR_LCS | RSR_RWTO | RSR_PLE | \
+				 RSR_AE | RSR_CE | RSR_FOE)
+/* 0x0A */
+#define FCR_TXPEN		BIT(5)
+#define FCR_BKPM		BIT(3)
+#define FCR_FLCE		BIT(0)
+#define FCR_RXTX_BITS		(FCR_TXPEN | FCR_BKPM | FCR_FLCE)
+/* 0x0B */
+#define EPCR_WEP		BIT(4)
+#define EPCR_EPOS		BIT(3)
+#define EPCR_ERPRR		BIT(2)
+#define EPCR_ERPRW		BIT(1)
+#define EPCR_ERRE		BIT(0)
+/* 0x1E */
+#define GPCR_GEP_CNTL		BIT(0)
+/* 0x1F */
+#define GPR_PHY_OFF		BIT(0)
+/* 0x30 */
+#define	ATCR_AUTO_TX		BIT(7)
+/* 0x39 */
+#define INTCR_POL_LOW		(1 << 0)
+#define INTCR_POL_HIGH		(0 << 0)
+/* 0x3D */
+/* Pause Packet Control Register - default = 1 */
+#define PPCR_PAUSE_COUNT	0x08
+/* 0x55 */
+#define MPCR_RSTTX		BIT(1)
+#define MPCR_RSTRX		BIT(0)
+/* 0x57 */
+/* LEDMode Control Register - LEDMode1 */
+/* Value 0x81 : bit[7] = 1, bit[2] = 0, bit[1:0] = 01b */
+#define LMCR_NEWMOD		BIT(7)
+#define LMCR_TYPED1		BIT(1)
+#define LMCR_TYPED0		BIT(0)
+#define LMCR_MODE1		(LMCR_NEWMOD | LMCR_TYPED0)
+/* 0x5E */
+#define MBNDRY_BYTE		BIT(7)
+/* 0xFE */
+#define ISR_MBS			BIT(7)
+#define ISR_LNKCHG		BIT(5)
+#define ISR_ROOS		BIT(3)
+#define ISR_ROS			BIT(2)
+#define ISR_PTS			BIT(1)
+#define ISR_PRS			BIT(0)
+#define ISR_CLR_INT		(ISR_LNKCHG | ISR_ROOS | ISR_ROS | \
+				 ISR_PTS | ISR_PRS)
+#define ISR_STOP_MRCMD		(ISR_MBS)
+/* 0xFF */
+#define IMR_PAR			BIT(7)
+#define IMR_LNKCHGI		BIT(5)
+#define IMR_PTM			BIT(1)
+#define IMR_PRM			BIT(0)
+
+/* Const
+ */
+#define DM9051_PHY_ADDR			1	/* PHY id */
+#define DM9051_PHY			0x40	/* PHY address 0x01 */
+#define DM9051_PKT_RDY			0x01	/* Packet ready to receive */
+#define DM9051_PKT_MAX			1536	/* Received packet max size */
+#define DM9051_TX_QUE_HI_WATER		50
+#define DM9051_TX_QUE_LO_WATER		25
+#define DM_EEPROM_MAGIC			0x9051
+
+#define	DM_RXHDR_SIZE			sizeof(struct dm9051_rxhdr)
+
+static inline struct board_info *to_dm9051_board(struct net_device *ndev)
+{
+	return netdev_priv(ndev);
+}
+
+#endif /* _DM9051_H_ */