Merge branch 'i2c-embedded/for-next' of git://git.pengutronix.de/git/wsa/linux

Pull embedded i2c changes from Wolfram Sang:
 "Changes for the "embedded" part of the I2C subsystem:

   - lots of devicetree conversions of drivers (and preparations for
     that)
   - big cleanups for drivers for OMAP, Tegra, Nomadik, Blackfin
   - Rafael's struct dev_pm_ops conversion patches for I2C
   - usual driver cleanups and fixes

  All patches have been in linux-next for an apropriate time and all
  patches touching files outside of i2c-folders should have proper acks
  from the maintainers."

* 'i2c-embedded/for-next' of git://git.pengutronix.de/git/wsa/linux: (60 commits)
  Revert "i2c: tegra: convert normal suspend/resume to *_noirq"
  I2C: MV64XYZ: Add Device Tree support
  i2c: stu300: use devm managed resources
  i2c: i2c-ocores: support for 16bit and 32bit IO
  V4L/DVB: mfd: use reg_shift instead of regstep
  i2c: i2c-ocores: Use reg-shift property
  i2c: i2c-ocores: DT bindings and minor fixes.
  i2c: mv64xxxx: remove EXPERIMENTAL tag
  i2c-s3c2410: Use plain pm_runtime_put()
  i2c: s3c2410: Fix pointer type passed to of_match_node()
  i2c: mxs: Set I2C timing registers for mxs-i2c
  i2c: i2c-bfin-twi: Move blackfin TWI register access Macro to head file.
  i2c: i2c-bfin-twi: Move TWI peripheral pin request array to platform data.
  i2c:i2c-bfin-twi: include twi head file
  i2c:i2c-bfin-twi: TWI fails to restart next transfer in high system load.
  i2c: i2c-bfin-twi: Tighten condition when failing I2C transfer if MEN bit is reset unexpectedly.
  i2c: i2c-bfin-twi: Break dead waiting loop if i2c device misbehaves.
  i2c: i2c-bfin-twi: Improve the patch for bug "Illegal i2c bus lock upon certain transfer scenarios".
  i2c: i2c-bfin-twi: Illegal i2c bus lock upon certain transfer scenarios.
  i2c-mv64xxxx: allow more than one driver instance
  ...

Conflicts:
	drivers/i2c/busses/i2c-nomadik.c

Documentation/devicetree/bindings/i2c/i2c-mxs.txt

@@ -4,6 +4,8 @@ Required properties:
 - compatible: Should be "fsl,<chip>-i2c"
 - reg: Should contain registers location and length
 - interrupts: Should contain ERROR and DMA interrupts
+- clock-frequency: Desired I2C bus clock frequency in Hz.
+                   Only 100000Hz and 400000Hz modes are supported.
 
 Examples:
 
@@ -13,4 +15,5 @@ i2c0: i2c@80058000 {
 	compatible = "fsl,imx28-i2c";
 	reg = <0x80058000 2000>;
 	interrupts = <111 68>;
+	clock-frequency = <100000>;
 };

Documentation/devicetree/bindings/i2c/i2c-ocores.txt

+Device tree configuration for i2c-ocores
+
+Required properties:
+- compatible      : "opencores,i2c-ocores"
+- reg             : bus address start and address range size of device
+- interrupts      : interrupt number
+- clock-frequency : frequency of bus clock in Hz
+- #address-cells  : should be <1>
+- #size-cells     : should be <0>
+
+Optional properties:
+- reg-shift       : device register offsets are shifted by this value
+- reg-io-width    : io register width in bytes (1, 2 or 4)
+- regstep         : deprecated, use reg-shift above
+
+Example:
+
+	i2c0: ocores@a0000000 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "opencores,i2c-ocores";
+		reg = <0xa0000000 0x8>;
+		interrupts = <10>;
+		clock-frequency = <20000000>;
+
+		reg-shift = <0>;	/* 8 bit registers */
+		reg-io-width = <1>;	/* 8 bit read/write */
+
+		dummy@60 {
+			compatible = "dummy";
+			reg = <0x60>;
+		};
+	};

Documentation/devicetree/bindings/i2c/mrvl-i2c.txt

-* I2C
+* Marvell MMP I2C controller
 
 Required properties :
 
@@ -32,3 +32,20 @@ Examples:
 		interrupts = <58>;
 	};
 
+* Marvell MV64XXX I2C controller
+
+Required properties :
+
+ - reg             : Offset and length of the register set for the device
+ - compatible      : Should be "marvell,mv64xxx-i2c"
+ - interrupts      : The interrupt number
+ - clock-frequency : Desired I2C bus clock frequency in Hz.
+
+Examples:
+
+	i2c@11000 {
+		compatible = "marvell,mv64xxx-i2c";
+		reg = <0x11000 0x20>;
+		interrupts = <29>;
+		clock-frequency = <100000>;
+	};

arch/arm/boot/dts/imx28.dtsi

@@ -660,6 +660,7 @@ i2c0: i2c@80058000 {
 				compatible = "fsl,imx28-i2c";
 				reg = <0x80058000 2000>;
 				interrupts = <111 68>;
+				clock-frequency = <100000>;
 				status = "disabled";
 			};
 
@@ -669,6 +670,7 @@ i2c1: i2c@8005a000 {
 				compatible = "fsl,imx28-i2c";
 				reg = <0x8005a000 2000>;
 				interrupts = <110 69>;
+				clock-frequency = <100000>;
 				status = "disabled";
 			};
 

arch/arm/mach-ux500/board-mop500.c

@@ -15,6 +15,7 @@
 #include <linux/platform_device.h>
 #include <linux/io.h>
 #include <linux/i2c.h>
+#include <linux/platform_data/i2c-nomadik.h>
 #include <linux/gpio.h>
 #include <linux/amba/bus.h>
 #include <linux/amba/pl022.h>
@@ -40,7 +41,6 @@
 #include <asm/mach/arch.h>
 #include <asm/hardware/gic.h>
 
-#include <plat/i2c.h>
 #include <plat/ste_dma40.h>
 #include <plat/gpio-nomadik.h>
 

arch/arm/mach-ux500/devices-common.h

@@ -12,7 +12,7 @@
 #include <linux/dma-mapping.h>
 #include <linux/sys_soc.h>
 #include <linux/amba/bus.h>
-#include <plat/i2c.h>
+#include <linux/platform_data/i2c-nomadik.h>
 #include <mach/crypto-ux500.h>
 
 struct spi_master_cntlr;
@@ -56,27 +56,15 @@ dbx500_add_uart(struct device *parent, const char *name, resource_size_t base,
 
 struct nmk_i2c_controller;
 
-static inline struct platform_device *
+static inline struct amba_device *
 dbx500_add_i2c(struct device *parent, int id, resource_size_t base, int irq,
 	       struct nmk_i2c_controller *data)
 {
-	struct resource res[] = {
-		DEFINE_RES_MEM(base, SZ_4K),
-		DEFINE_RES_IRQ(irq),
-	};
+	/* Conjure a name similar to what the platform device used to have */
+	char name[16];
 
-	struct platform_device_info pdevinfo = {
-		.parent = parent,
-		.name = "nmk-i2c",
-		.id = id,
-		.res = res,
-		.num_res = ARRAY_SIZE(res),
-		.data = data,
-		.size_data = sizeof(*data),
-		.dma_mask = DMA_BIT_MASK(32),
-	};
-
-	return platform_device_register_full(&pdevinfo);
+	snprintf(name, sizeof(name), "nmk-i2c.%d", id);
+	return amba_apb_device_add(parent, name, base, SZ_4K, irq, 0, data, 0);
 }
 
 static inline struct amba_device *

arch/arm/plat-mxc/include/mach/i2c.h

@@ -15,7 +15,7 @@
  *
  **/
 struct imxi2c_platform_data {
-	int bitrate;
+	u32 bitrate;
 };
 
 #endif /* __ASM_ARCH_I2C_H_ */

drivers/i2c/busses/Kconfig

@@ -462,7 +462,7 @@ config I2C_MPC
 
 config I2C_MV64XXX
 	tristate "Marvell mv64xxx I2C Controller"
-	depends on (MV64X60 || PLAT_ORION) && EXPERIMENTAL
+	depends on (MV64X60 || PLAT_ORION)
 	help
 	  If you say yes to this option, support will be included for the
 	  built-in I2C interface on the Marvell 64xxx line of host bridges.
@@ -483,10 +483,11 @@ config I2C_MXS
 
 config I2C_NOMADIK
 	tristate "ST-Ericsson Nomadik/Ux500 I2C Controller"
-	depends on PLAT_NOMADIK
+	depends on ARM_AMBA
 	help
 	  If you say yes to this option, support will be included for the
-	  I2C interface from ST-Ericsson's Nomadik and Ux500 architectures.
+	  I2C interface from ST-Ericsson's Nomadik and Ux500 architectures,
+	  as well as the STA2X11 PCIe I/O HUB.
 
 config I2C_NUC900
 	tristate "NUC900 I2C Driver"

drivers/i2c/busses/i2c-at91.c

@@ -279,30 +279,31 @@ static int __devexit at91_i2c_remove(struct platform_device *pdev)
 
 /* NOTE: could save a few mA by keeping clock off outside of at91_xfer... */
 
-static int at91_i2c_suspend(struct platform_device *pdev, pm_message_t mesg)
+static int at91_i2c_suspend(struct device *dev)
 {
 	clk_disable(twi_clk);
 	return 0;
 }
 
-static int at91_i2c_resume(struct platform_device *pdev)
+static int at91_i2c_resume(struct device *dev)
 {
 	return clk_enable(twi_clk);
 }
 
+static SIMPLE_DEV_PM_OPS(at91_i2c_pm, at91_i2c_suspend, at91_i2c_resume);
+#define AT91_I2C_PM	(&at91_i2c_pm)
+
 #else
-#define at91_i2c_suspend	NULL
-#define at91_i2c_resume		NULL
+#define AT91_I2C_PM	NULL
 #endif
 
 static struct platform_driver at91_i2c_driver = {
 	.probe		= at91_i2c_probe,
 	.remove		= __devexit_p(at91_i2c_remove),
-	.suspend	= at91_i2c_suspend,
-	.resume		= at91_i2c_resume,
 	.driver		= {
 		.name	= "at91_i2c",
 		.owner	= THIS_MODULE,
+		.pm	= AT91_I2C_PM,
 	},
 };
 

drivers/i2c/busses/i2c-bfin-twi.c

@@ -25,6 +25,7 @@
 #include <asm/blackfin.h>
 #include <asm/portmux.h>
 #include <asm/irq.h>
+#include <asm/bfin_twi.h>
 
 /* SMBus mode*/
 #define TWI_I2C_MODE_STANDARD		1
@@ -32,56 +33,6 @@
 #define TWI_I2C_MODE_COMBINED		3
 #define TWI_I2C_MODE_REPEAT		4
 
-struct bfin_twi_iface {
-	int			irq;
-	spinlock_t		lock;
-	char			read_write;
-	u8			command;
-	u8			*transPtr;
-	int			readNum;
-	int			writeNum;
-	int			cur_mode;
-	int			manual_stop;
-	int			result;
-	struct i2c_adapter	adap;
-	struct completion	complete;
-	struct i2c_msg 		*pmsg;
-	int			msg_num;
-	int			cur_msg;
-	u16			saved_clkdiv;
-	u16			saved_control;
-	void __iomem		*regs_base;
-};
-
-
-#define DEFINE_TWI_REG(reg, off) \
-static inline u16 read_##reg(struct bfin_twi_iface *iface) \
-	{ return bfin_read16(iface->regs_base + (off)); } \
-static inline void write_##reg(struct bfin_twi_iface *iface, u16 v) \
-	{ bfin_write16(iface->regs_base + (off), v); }
-
-DEFINE_TWI_REG(CLKDIV, 0x00)
-DEFINE_TWI_REG(CONTROL, 0x04)
-DEFINE_TWI_REG(SLAVE_CTL, 0x08)
-DEFINE_TWI_REG(SLAVE_STAT, 0x0C)
-DEFINE_TWI_REG(SLAVE_ADDR, 0x10)
-DEFINE_TWI_REG(MASTER_CTL, 0x14)
-DEFINE_TWI_REG(MASTER_STAT, 0x18)
-DEFINE_TWI_REG(MASTER_ADDR, 0x1C)
-DEFINE_TWI_REG(INT_STAT, 0x20)
-DEFINE_TWI_REG(INT_MASK, 0x24)
-DEFINE_TWI_REG(FIFO_CTL, 0x28)
-DEFINE_TWI_REG(FIFO_STAT, 0x2C)
-DEFINE_TWI_REG(XMT_DATA8, 0x80)
-DEFINE_TWI_REG(XMT_DATA16, 0x84)
-DEFINE_TWI_REG(RCV_DATA8, 0x88)
-DEFINE_TWI_REG(RCV_DATA16, 0x8C)
-
-static const u16 pin_req[2][3] = {
-	{P_TWI0_SCL, P_TWI0_SDA, 0},
-	{P_TWI1_SCL, P_TWI1_SDA, 0},
-};
-
 static void bfin_twi_handle_interrupt(struct bfin_twi_iface *iface,
 					unsigned short twi_int_status)
 {
@@ -99,7 +50,7 @@ static void bfin_twi_handle_interrupt(struct bfin_twi_iface *iface,
 		 */
 		else if (iface->cur_mode == TWI_I2C_MODE_COMBINED)
 			write_MASTER_CTL(iface,
-				read_MASTER_CTL(iface) | MDIR | RSTART);
+				read_MASTER_CTL(iface) | MDIR);
 		else if (iface->manual_stop)
 			write_MASTER_CTL(iface,
 				read_MASTER_CTL(iface) | STOP);
@@ -107,10 +58,10 @@ static void bfin_twi_handle_interrupt(struct bfin_twi_iface *iface,
 		         iface->cur_msg + 1 < iface->msg_num) {
 			if (iface->pmsg[iface->cur_msg + 1].flags & I2C_M_RD)
 				write_MASTER_CTL(iface,
-					read_MASTER_CTL(iface) | RSTART | MDIR);
+					read_MASTER_CTL(iface) | MDIR);
 			else
 				write_MASTER_CTL(iface,
-					(read_MASTER_CTL(iface) | RSTART) & ~MDIR);
+					read_MASTER_CTL(iface) & ~MDIR);
 		}
 	}
 	if (twi_int_status & RCVSERV) {
@@ -130,17 +81,25 @@ static void bfin_twi_handle_interrupt(struct bfin_twi_iface *iface,
 			}
 			iface->transPtr++;
 			iface->readNum--;
-		} else if (iface->manual_stop) {
-			write_MASTER_CTL(iface,
-				read_MASTER_CTL(iface) | STOP);
-		} else if (iface->cur_mode == TWI_I2C_MODE_REPEAT &&
-		           iface->cur_msg + 1 < iface->msg_num) {
-			if (iface->pmsg[iface->cur_msg + 1].flags & I2C_M_RD)
-				write_MASTER_CTL(iface,
-					read_MASTER_CTL(iface) | RSTART | MDIR);
-			else
+		}
+
+		if (iface->readNum == 0) {
+			if (iface->manual_stop) {
+				/* Temporary workaround to avoid possible bus stall -
+				 * Flush FIFO before issuing the STOP condition
+				 */
+				read_RCV_DATA16(iface);
 				write_MASTER_CTL(iface,
-					(read_MASTER_CTL(iface) | RSTART) & ~MDIR);
+					read_MASTER_CTL(iface) | STOP);
+			} else if (iface->cur_mode == TWI_I2C_MODE_REPEAT &&
+					iface->cur_msg + 1 < iface->msg_num) {
+				if (iface->pmsg[iface->cur_msg + 1].flags & I2C_M_RD)
+					write_MASTER_CTL(iface,
+						read_MASTER_CTL(iface) | MDIR);
+				else
+					write_MASTER_CTL(iface,
+						read_MASTER_CTL(iface) & ~MDIR);
+			}
 		}
 	}
 	if (twi_int_status & MERR) {
@@ -193,7 +152,8 @@ static void bfin_twi_handle_interrupt(struct bfin_twi_iface *iface,
 		return;
 	}
 	if (twi_int_status & MCOMP) {
-		if ((read_MASTER_CTL(iface) & MEN) == 0 &&
+		if (twi_int_status & (XMTSERV | RCVSERV) &&
+			(read_MASTER_CTL(iface) & MEN) == 0 &&
 			(iface->cur_mode == TWI_I2C_MODE_REPEAT ||
 			iface->cur_mode == TWI_I2C_MODE_COMBINED)) {
 			iface->result = -1;
@@ -221,7 +181,7 @@ static void bfin_twi_handle_interrupt(struct bfin_twi_iface *iface,
 			write_MASTER_CTL(iface,
 				read_MASTER_CTL(iface) & ~RSTART);
 		} else if (iface->cur_mode == TWI_I2C_MODE_REPEAT &&
-				iface->cur_msg+1 < iface->msg_num) {
+				iface->cur_msg + 1 < iface->msg_num) {
 			iface->cur_msg++;
 			iface->transPtr = iface->pmsg[iface->cur_msg].buf;
 			iface->writeNum = iface->readNum =
@@ -241,27 +201,29 @@ static void bfin_twi_handle_interrupt(struct bfin_twi_iface *iface,
 				}
 			}
 
-			if (iface->pmsg[iface->cur_msg].len <= 255)
-					write_MASTER_CTL(iface,
+			if (iface->pmsg[iface->cur_msg].len <= 255) {
+				write_MASTER_CTL(iface,
 					(read_MASTER_CTL(iface) &
 					(~(0xff << 6))) |
-				(iface->pmsg[iface->cur_msg].len << 6));
-			else {
+					(iface->pmsg[iface->cur_msg].len << 6));
+				iface->manual_stop = 0;
+			} else {
 				write_MASTER_CTL(iface,
 					(read_MASTER_CTL(iface) |
 					(0xff << 6)));
 				iface->manual_stop = 1;
 			}
-			/* remove restart bit and enable master receive */
-			write_MASTER_CTL(iface,
-				read_MASTER_CTL(iface) & ~RSTART);
+			/* remove restart bit before last message */
+			if (iface->cur_msg + 1 == iface->msg_num)
+				write_MASTER_CTL(iface,
+					read_MASTER_CTL(iface) & ~RSTART);
 		} else {
 			iface->result = 1;
 			write_INT_MASK(iface, 0);
 			write_MASTER_CTL(iface, 0);
 		}
+		complete(&iface->complete);
 	}
-	complete(&iface->complete);
 }
 
 /* Interrupt handler */
@@ -298,8 +260,8 @@ static int bfin_twi_do_master_xfer(struct i2c_adapter *adap,
 	if (!(read_CONTROL(iface) & TWI_ENA))
 		return -ENXIO;
 
-	while (read_MASTER_STAT(iface) & BUSBUSY)
-		yield();
+	if (read_MASTER_STAT(iface) & BUSBUSY)
+		return -EAGAIN;
 
 	iface->pmsg = msgs;
 	iface->msg_num = num;
@@ -311,7 +273,8 @@ static int bfin_twi_do_master_xfer(struct i2c_adapter *adap,
 		return -EINVAL;
 	}
 
-	iface->cur_mode = TWI_I2C_MODE_REPEAT;
+	if (iface->msg_num > 1)
+		iface->cur_mode = TWI_I2C_MODE_REPEAT;
 	iface->manual_stop = 0;
 	iface->transPtr = pmsg->buf;
 	iface->writeNum = iface->readNum = pmsg->len;
@@ -356,6 +319,7 @@ static int bfin_twi_do_master_xfer(struct i2c_adapter *adap,
 
 	/* Master enable */
 	write_MASTER_CTL(iface, read_MASTER_CTL(iface) | MEN |
+		(iface->msg_num > 1 ? RSTART : 0) |
 		((iface->read_write == I2C_SMBUS_READ) ? MDIR : 0) |
 		((CONFIG_I2C_BLACKFIN_TWI_CLK_KHZ > 100) ? FAST : 0));
 	SSYNC();
@@ -398,8 +362,8 @@ int bfin_twi_do_smbus_xfer(struct i2c_adapter *adap, u16 addr,
 	if (!(read_CONTROL(iface) & TWI_ENA))
 		return -ENXIO;
 
-	while (read_MASTER_STAT(iface) & BUSBUSY)
-		yield();
+	if (read_MASTER_STAT(iface) & BUSBUSY)
+		return -EAGAIN;
 
 	iface->writeNum = 0;
 	iface->readNum = 0;
@@ -520,7 +484,7 @@ int bfin_twi_do_smbus_xfer(struct i2c_adapter *adap, u16 addr,
 		else
 			write_MASTER_CTL(iface, 0x1 << 6);
 		/* Master enable */
-		write_MASTER_CTL(iface, read_MASTER_CTL(iface) | MEN |
+		write_MASTER_CTL(iface, read_MASTER_CTL(iface) | MEN | RSTART |
 			((CONFIG_I2C_BLACKFIN_TWI_CLK_KHZ>100) ? FAST : 0));
 		break;
 	default:
@@ -611,9 +575,9 @@ static struct i2c_algorithm bfin_twi_algorithm = {
 	.functionality = bfin_twi_functionality,
 };
 
-static int i2c_bfin_twi_suspend(struct platform_device *pdev, pm_message_t state)
+static int i2c_bfin_twi_suspend(struct device *dev)
 {
-	struct bfin_twi_iface *iface = platform_get_drvdata(pdev);
+	struct bfin_twi_iface *iface = dev_get_drvdata(dev);
 
 	iface->saved_clkdiv = read_CLKDIV(iface);
 	iface->saved_control = read_CONTROL(iface);
@@ -626,14 +590,14 @@ static int i2c_bfin_twi_suspend(struct platform_device *pdev, pm_message_t state
 	return 0;
 }
 
-static int i2c_bfin_twi_resume(struct platform_device *pdev)
+static int i2c_bfin_twi_resume(struct device *dev)
 {
-	struct bfin_twi_iface *iface = platform_get_drvdata(pdev);
+	struct bfin_twi_iface *iface = dev_get_drvdata(dev);
 
 	int rc = request_irq(iface->irq, bfin_twi_interrupt_entry,
-		0, pdev->name, iface);
+		0, to_platform_device(dev)->name, iface);
 	if (rc) {
-		dev_err(&pdev->dev, "Can't get IRQ %d !\n", iface->irq);
+		dev_err(dev, "Can't get IRQ %d !\n", iface->irq);
 		return -ENODEV;
 	}
 
@@ -646,6 +610,9 @@ static int i2c_bfin_twi_resume(struct platform_device *pdev)
 	return 0;
 }
 
+static SIMPLE_DEV_PM_OPS(i2c_bfin_twi_pm,
+			 i2c_bfin_twi_suspend, i2c_bfin_twi_resume);
+
 static int i2c_bfin_twi_probe(struct platform_device *pdev)
 {
 	struct bfin_twi_iface *iface;
@@ -695,7 +662,8 @@ static int i2c_bfin_twi_probe(struct platform_device *pdev)
 	p_adap->timeout = 5 * HZ;
 	p_adap->retries = 3;
 
-	rc = peripheral_request_list(pin_req[pdev->id], "i2c-bfin-twi");
+	rc = peripheral_request_list((unsigned short *)pdev->dev.platform_data,
+					"i2c-bfin-twi");
 	if (rc) {
 		dev_err(&pdev->dev, "Can't setup pin mux!\n");
 		goto out_error_pin_mux;
@@ -742,7 +710,7 @@ static int i2c_bfin_twi_probe(struct platform_device *pdev)
 	free_irq(iface->irq, iface);
 out_error_req_irq:
 out_error_no_irq:
-	peripheral_free_list(pin_req[pdev->id]);
+	peripheral_free_list((unsigned short *)pdev->dev.platform_data);
 out_error_pin_mux:
 	iounmap(iface->regs_base);
 out_error_ioremap:
@@ -760,7 +728,7 @@ static int i2c_bfin_twi_remove(struct platform_device *pdev)
 
 	i2c_del_adapter(&(iface->adap));
 	free_irq(iface->irq, iface);
-	peripheral_free_list(pin_req[pdev->id]);
+	peripheral_free_list((unsigned short *)pdev->dev.platform_data);
 	iounmap(iface->regs_base);
 	kfree(iface);
 
@@ -770,11 +738,10 @@ static int i2c_bfin_twi_remove(struct platform_device *pdev)
 static struct platform_driver i2c_bfin_twi_driver = {
 	.probe		= i2c_bfin_twi_probe,
 	.remove		= i2c_bfin_twi_remove,
-	.suspend	= i2c_bfin_twi_suspend,
-	.resume		= i2c_bfin_twi_resume,
 	.driver		= {
 		.name	= "i2c-bfin-twi",
 		.owner	= THIS_MODULE,
+		.pm	= &i2c_bfin_twi_pm,
 	},
 };
 

drivers/i2c/busses/i2c-imx.c

@@ -117,10 +117,8 @@ static u16 __initdata i2c_clk_div[50][2] = {
 
 struct imx_i2c_struct {
 	struct i2c_adapter	adapter;
-	struct resource		*res;
 	struct clk		*clk;
 	void __iomem		*base;
-	int			irq;
 	wait_queue_head_t	queue;
 	unsigned long		i2csr;
 	unsigned int 		disable_delay;
@@ -472,9 +470,8 @@ static int __init i2c_imx_probe(struct platform_device *pdev)
 	struct imxi2c_platform_data *pdata = pdev->dev.platform_data;
 	struct pinctrl *pinctrl;
 	void __iomem *base;
-	resource_size_t res_size;
-	int irq, bitrate;
-	int ret;
+	int irq, ret;
+	u32 bitrate;
 
 	dev_dbg(&pdev->dev, "<%s>\n", __func__);
 
@@ -489,25 +486,15 @@ static int __init i2c_imx_probe(struct platform_device *pdev)
 		return -ENOENT;
 	}
 
-	res_size = resource_size(res);
-
-	if (!request_mem_region(res->start, res_size, DRIVER_NAME)) {
-		dev_err(&pdev->dev, "request_mem_region failed\n");
+	base = devm_request_and_ioremap(&pdev->dev, res);
+	if (!base)
 		return -EBUSY;
-	}
-
-	base = ioremap(res->start, res_size);
-	if (!base) {
-		dev_err(&pdev->dev, "ioremap failed\n");
-		ret = -EIO;
-		goto fail1;
-	}
 
-	i2c_imx = kzalloc(sizeof(struct imx_i2c_struct), GFP_KERNEL);
+	i2c_imx = devm_kzalloc(&pdev->dev, sizeof(struct imx_i2c_struct),
+				GFP_KERNEL);
 	if (!i2c_imx) {
 		dev_err(&pdev->dev, "can't allocate interface\n");
-		ret = -ENOMEM;
-		goto fail2;
+		return -ENOMEM;
 	}
 
 	/* Setup i2c_imx driver structure */
@@ -517,29 +504,27 @@ static int __init i2c_imx_probe(struct platform_device *pdev)
 	i2c_imx->adapter.dev.parent	= &pdev->dev;
 	i2c_imx->adapter.nr 		= pdev->id;
 	i2c_imx->adapter.dev.of_node	= pdev->dev.of_node;
-	i2c_imx->irq			= irq;
 	i2c_imx->base			= base;
-	i2c_imx->res			= res;
 
 	pinctrl = devm_pinctrl_get_select_default(&pdev->dev);
 	if (IS_ERR(pinctrl)) {
-		ret = PTR_ERR(pinctrl);
-		goto fail3;
+		dev_err(&pdev->dev, "can't get/select pinctrl\n");
+		return PTR_ERR(pinctrl);
 	}
 
 	/* Get I2C clock */
-	i2c_imx->clk = clk_get(&pdev->dev, "i2c_clk");
+	i2c_imx->clk = devm_clk_get(&pdev->dev, NULL);
 	if (IS_ERR(i2c_imx->clk)) {
-		ret = PTR_ERR(i2c_imx->clk);
 		dev_err(&pdev->dev, "can't get I2C clock\n");
-		goto fail3;
+		return PTR_ERR(i2c_imx->clk);
 	}
 
 	/* Request IRQ */
-	ret = request_irq(i2c_imx->irq, i2c_imx_isr, 0, pdev->name, i2c_imx);
+	ret = devm_request_irq(&pdev->dev, irq, i2c_imx_isr, 0,
+				pdev->name, i2c_imx);
 	if (ret) {
-		dev_err(&pdev->dev, "can't claim irq %d\n", i2c_imx->irq);
-		goto fail4;
+		dev_err(&pdev->dev, "can't claim irq %d\n", irq);
+		return ret;
 	}
 
 	/* Init queue */
@@ -564,7 +549,7 @@ static int __init i2c_imx_probe(struct platform_device *pdev)
 	ret = i2c_add_numbered_adapter(&i2c_imx->adapter);
 	if (ret < 0) {
 		dev_err(&pdev->dev, "registration failed\n");
-		goto fail5;
+		return ret;
 	}
 
 	of_i2c_register_devices(&i2c_imx->adapter);
@@ -572,28 +557,16 @@ static int __init i2c_imx_probe(struct platform_device *pdev)
 	/* Set up platform driver data */
 	platform_set_drvdata(pdev, i2c_imx);
 
-	dev_dbg(&i2c_imx->adapter.dev, "claimed irq %d\n", i2c_imx->irq);
+	dev_dbg(&i2c_imx->adapter.dev, "claimed irq %d\n", irq);
 	dev_dbg(&i2c_imx->adapter.dev, "device resources from 0x%x to 0x%x\n",
-		i2c_imx->res->start, i2c_imx->res->end);
-	dev_dbg(&i2c_imx->adapter.dev, "allocated %d bytes at 0x%x \n",
-		res_size, i2c_imx->res->start);
+		res->start, res->end);
+	dev_dbg(&i2c_imx->adapter.dev, "allocated %d bytes at 0x%x\n",
+		resource_size(res), res->start);
 	dev_dbg(&i2c_imx->adapter.dev, "adapter name: \"%s\"\n",
 		i2c_imx->adapter.name);
 	dev_dbg(&i2c_imx->adapter.dev, "IMX I2C adapter registered\n");
 
 	return 0;   /* Return OK */
-
-fail5:
-	free_irq(i2c_imx->irq, i2c_imx);
-fail4:
-	clk_put(i2c_imx->clk);
-fail3:
-	kfree(i2c_imx);
-fail2:
-	iounmap(base);
-fail1:
-	release_mem_region(res->start, resource_size(res));
-	return ret; /* Return error number */
 }
 
 static int __exit i2c_imx_remove(struct platform_device *pdev)
@@ -605,20 +578,12 @@ static int __exit i2c_imx_remove(struct platform_device *pdev)
 	i2c_del_adapter(&i2c_imx->adapter);
 	platform_set_drvdata(pdev, NULL);
 
-	/* free interrupt */
-	free_irq(i2c_imx->irq, i2c_imx);
-
 	/* setup chip registers to defaults */
 	writeb(0, i2c_imx->base + IMX_I2C_IADR);
 	writeb(0, i2c_imx->base + IMX_I2C_IFDR);
 	writeb(0, i2c_imx->base + IMX_I2C_I2CR);
 	writeb(0, i2c_imx->base + IMX_I2C_I2SR);
 
-	clk_put(i2c_imx->clk);
-
-	iounmap(i2c_imx->base);
-	release_mem_region(i2c_imx->res->start, resource_size(i2c_imx->res));
-	kfree(i2c_imx);
 	return 0;
 }
 

drivers/i2c/busses/i2c-mv64xxx.c

@@ -18,6 +18,11 @@
 #include <linux/mv643xx_i2c.h>
 #include <linux/platform_device.h>
 #include <linux/io.h>
+#include <linux/of.h>
+#include <linux/of_irq.h>
+#include <linux/of_i2c.h>
+#include <linux/clk.h>
+#include <linux/err.h>
 
 /* Register defines */
 #define	MV64XXX_I2C_REG_SLAVE_ADDR			0x00
@@ -98,6 +103,9 @@ struct mv64xxx_i2c_data {
 	int			rc;
 	u32			freq_m;
 	u32			freq_n;
+#if defined(CONFIG_HAVE_CLK)
+	struct clk              *clk;
+#endif
 	wait_queue_head_t	waitq;
 	spinlock_t		lock;
 	struct i2c_msg		*msg;
@@ -521,6 +529,82 @@ mv64xxx_i2c_unmap_regs(struct mv64xxx_i2c_data *drv_data)
 	drv_data->reg_base_p = 0;
 }
 
+#ifdef CONFIG_OF
+static int __devinit
+mv64xxx_calc_freq(const int tclk, const int n, const int m)
+{
+	return tclk / (10 * (m + 1) * (2 << n));
+}
+
+static bool __devinit
+mv64xxx_find_baud_factors(const u32 req_freq, const u32 tclk, u32 *best_n,
+			  u32 *best_m)
+{
+	int freq, delta, best_delta = INT_MAX;
+	int m, n;
+
+	for (n = 0; n <= 7; n++)
+		for (m = 0; m <= 15; m++) {
+			freq = mv64xxx_calc_freq(tclk, n, m);
+			delta = req_freq - freq;
+			if (delta >= 0 && delta < best_delta) {
+				*best_m = m;
+				*best_n = n;
+				best_delta = delta;
+			}
+			if (best_delta == 0)
+				return true;
+		}
+	if (best_delta == INT_MAX)
+		return false;
+	return true;
+}
+
+static int __devinit
+mv64xxx_of_config(struct mv64xxx_i2c_data *drv_data,
+		  struct device_node *np)
+{
+	u32 bus_freq, tclk;
+	int rc = 0;
+
+	/* CLK is mandatory when using DT to describe the i2c bus. We
+	 * need to know tclk in order to calculate bus clock
+	 * factors.
+	 */
+#if !defined(CONFIG_HAVE_CLK)
+	/* Have OF but no CLK */
+	return -ENODEV;
+#else
+	if (IS_ERR(drv_data->clk)) {
+		rc = -ENODEV;
+		goto out;
+	}
+	tclk = clk_get_rate(drv_data->clk);
+	of_property_read_u32(np, "clock-frequency", &bus_freq);
+	if (!mv64xxx_find_baud_factors(bus_freq, tclk,
+				       &drv_data->freq_n, &drv_data->freq_m)) {
+		rc = -EINVAL;
+		goto out;
+	}
+	drv_data->irq = irq_of_parse_and_map(np, 0);
+
+	/* Its not yet defined how timeouts will be specified in device tree.
+	 * So hard code the value to 1 second.
+	 */
+	drv_data->adapter.timeout = HZ;
+out:
+	return rc;
+#endif
+}
+#else /* CONFIG_OF */
+static int __devinit
+mv64xxx_of_config(struct mv64xxx_i2c_data *drv_data,
+		  struct device_node *np)
+{
+	return -ENODEV;
+}
+#endif /* CONFIG_OF */
+
 static int __devinit
 mv64xxx_i2c_probe(struct platform_device *pd)
 {
@@ -528,7 +612,7 @@ mv64xxx_i2c_probe(struct platform_device *pd)
 	struct mv64xxx_i2c_pdata	*pdata = pd->dev.platform_data;
 	int	rc;
 
-	if ((pd->id != 0) || !pdata)
+	if ((!pdata && !pd->dev.of_node))
 		return -ENODEV;
 
 	drv_data = kzalloc(sizeof(struct mv64xxx_i2c_data), GFP_KERNEL);
@@ -546,19 +630,35 @@ mv64xxx_i2c_probe(struct platform_device *pd)
 	init_waitqueue_head(&drv_data->waitq);
 	spin_lock_init(&drv_data->lock);
 
-	drv_data->freq_m = pdata->freq_m;
-	drv_data->freq_n = pdata->freq_n;
-	drv_data->irq = platform_get_irq(pd, 0);
+#if defined(CONFIG_HAVE_CLK)
+	/* Not all platforms have a clk */
+	drv_data->clk = clk_get(&pd->dev, NULL);
+	if (!IS_ERR(drv_data->clk)) {
+		clk_prepare(drv_data->clk);
+		clk_enable(drv_data->clk);
+	}
+#endif
+	if (pdata) {
+		drv_data->freq_m = pdata->freq_m;
+		drv_data->freq_n = pdata->freq_n;
+		drv_data->irq = platform_get_irq(pd, 0);
+		drv_data->adapter.timeout = msecs_to_jiffies(pdata->timeout);
+	} else if (pd->dev.of_node) {
+		rc = mv64xxx_of_config(drv_data, pd->dev.of_node);
+		if (rc)
+			goto exit_unmap_regs;
+	}
 	if (drv_data->irq < 0) {
 		rc = -ENXIO;
 		goto exit_unmap_regs;
 	}
+
 	drv_data->adapter.dev.parent = &pd->dev;
 	drv_data->adapter.algo = &mv64xxx_i2c_algo;
 	drv_data->adapter.owner = THIS_MODULE;
 	drv_data->adapter.class = I2C_CLASS_HWMON | I2C_CLASS_SPD;
-	drv_data->adapter.timeout = msecs_to_jiffies(pdata->timeout);
 	drv_data->adapter.nr = pd->id;
+	drv_data->adapter.dev.of_node = pd->dev.of_node;
 	platform_set_drvdata(pd, drv_data);
 	i2c_set_adapdata(&drv_data->adapter, drv_data);
 
@@ -577,11 +677,20 @@ mv64xxx_i2c_probe(struct platform_device *pd)
 		goto exit_free_irq;
 	}
 
+	of_i2c_register_devices(&drv_data->adapter);
+
 	return 0;
 
 	exit_free_irq:
 		free_irq(drv_data->irq, drv_data);
 	exit_unmap_regs:
+#if defined(CONFIG_HAVE_CLK)
+	/* Not all platforms have a clk */
+	if (!IS_ERR(drv_data->clk)) {
+		clk_disable(drv_data->clk);
+		clk_unprepare(drv_data->clk);
+	}
+#endif
 		mv64xxx_i2c_unmap_regs(drv_data);
 	exit_kfree:
 		kfree(drv_data);
@@ -597,17 +706,31 @@ mv64xxx_i2c_remove(struct platform_device *dev)
 	rc = i2c_del_adapter(&drv_data->adapter);
 	free_irq(drv_data->irq, drv_data);
 	mv64xxx_i2c_unmap_regs(drv_data);
+#if defined(CONFIG_HAVE_CLK)
+	/* Not all platforms have a clk */
+	if (!IS_ERR(drv_data->clk)) {
+		clk_disable(drv_data->clk);
+		clk_unprepare(drv_data->clk);
+	}
+#endif
 	kfree(drv_data);
 
 	return rc;
 }
 
+static const struct of_device_id mv64xxx_i2c_of_match_table[] __devinitdata = {
+	{ .compatible = "marvell,mv64xxx-i2c", },
+	{}
+};
+MODULE_DEVICE_TABLE(of, mv64xxx_i2c_of_match_table);
+
 static struct platform_driver mv64xxx_i2c_driver = {
 	.probe	= mv64xxx_i2c_probe,
 	.remove	= __devexit_p(mv64xxx_i2c_remove),
 	.driver	= {
 		.owner	= THIS_MODULE,
 		.name	= MV64XXX_I2C_CTLR_NAME,
+		.of_match_table = of_match_ptr(mv64xxx_i2c_of_match_table),
 	},
 };
 

drivers/i2c/busses/i2c-mxs.c

@@ -46,6 +46,10 @@
 #define MXS_I2C_CTRL0_DIRECTION			0x00010000
 #define MXS_I2C_CTRL0_XFER_COUNT(v)		((v) & 0x0000FFFF)
 
+#define MXS_I2C_TIMING0		(0x10)
+#define MXS_I2C_TIMING1		(0x20)
+#define MXS_I2C_TIMING2		(0x30)
+
 #define MXS_I2C_CTRL1		(0x40)
 #define MXS_I2C_CTRL1_SET	(0x44)
 #define MXS_I2C_CTRL1_CLR	(0x48)
@@ -97,6 +101,35 @@
 #define MXS_CMD_I2C_READ	(MXS_I2C_CTRL0_SEND_NAK_ON_LAST | \
 				 MXS_I2C_CTRL0_MASTER_MODE)
 
+struct mxs_i2c_speed_config {
+	uint32_t	timing0;
+	uint32_t	timing1;
+	uint32_t	timing2;
+};
+
+/*
+ * Timing values for the default 24MHz clock supplied into the i2c block.
+ *
+ * The bus can operate at 95kHz or at 400kHz with the following timing
+ * register configurations. The 100kHz mode isn't present because it's
+ * values are not stated in the i.MX233/i.MX28 datasheet. The 95kHz mode
+ * shall be close enough replacement. Therefore when the bus is configured
+ * for 100kHz operation, 95kHz timing settings are actually loaded.
+ *
+ * For details, see i.MX233 [25.4.2 - 25.4.4] and i.MX28 [27.5.2 - 27.5.4].
+ */
+static const struct mxs_i2c_speed_config mxs_i2c_95kHz_config = {
+	.timing0	= 0x00780030,
+	.timing1	= 0x00800030,
+	.timing2	= 0x00300030,
+};
+
+static const struct mxs_i2c_speed_config mxs_i2c_400kHz_config = {
+	.timing0	= 0x000f0007,
+	.timing1	= 0x001f000f,
+	.timing2	= 0x00300030,
+};
+
 /**
  * struct mxs_i2c_dev - per device, private MXS-I2C data
  *
@@ -112,11 +145,17 @@ struct mxs_i2c_dev {
 	struct completion cmd_complete;
 	u32 cmd_err;
 	struct i2c_adapter adapter;
+	const struct mxs_i2c_speed_config *speed;
 };
 
 static void mxs_i2c_reset(struct mxs_i2c_dev *i2c)
 {
 	stmp_reset_block(i2c->regs);
+
+	writel(i2c->speed->timing0, i2c->regs + MXS_I2C_TIMING0);
+	writel(i2c->speed->timing1, i2c->regs + MXS_I2C_TIMING1);
+	writel(i2c->speed->timing2, i2c->regs + MXS_I2C_TIMING2);
+
 	writel(MXS_I2C_IRQ_MASK << 8, i2c->regs + MXS_I2C_CTRL1_SET);
 	writel(MXS_I2C_QUEUECTRL_PIO_QUEUE_MODE,
 			i2c->regs + MXS_I2C_QUEUECTRL_SET);
@@ -193,7 +232,7 @@ static int mxs_i2c_wait_for_data(struct mxs_i2c_dev *i2c)
 
 static int mxs_i2c_finish_read(struct mxs_i2c_dev *i2c, u8 *buf, int len)
 {
-	u32 data;
+	u32 uninitialized_var(data);
 	int i;
 
 	for (i = 0; i < len; i++) {
@@ -319,6 +358,28 @@ static const struct i2c_algorithm mxs_i2c_algo = {
 	.functionality = mxs_i2c_func,
 };
 
+static int mxs_i2c_get_ofdata(struct mxs_i2c_dev *i2c)
+{
+	uint32_t speed;
+	struct device *dev = i2c->dev;
+	struct device_node *node = dev->of_node;
+	int ret;
+
+	if (!node)
+		return -EINVAL;
+
+	i2c->speed = &mxs_i2c_95kHz_config;
+	ret = of_property_read_u32(node, "clock-frequency", &speed);
+	if (ret)
+		dev_warn(dev, "No I2C speed selected, using 100kHz\n");
+	else if (speed == 400000)
+		i2c->speed = &mxs_i2c_400kHz_config;
+	else if (speed != 100000)
+		dev_warn(dev, "Unsupported I2C speed selected, using 100kHz\n");
+
+	return 0;
+}
+
 static int __devinit mxs_i2c_probe(struct platform_device *pdev)
 {
 	struct device *dev = &pdev->dev;
@@ -358,6 +419,11 @@ static int __devinit mxs_i2c_probe(struct platform_device *pdev)
 		return err;
 
 	i2c->dev = dev;
+
+	err = mxs_i2c_get_ofdata(i2c);
+	if (err)
+		return err;
+
 	platform_set_drvdata(pdev, i2c);
 
 	/* Do reset to enforce correct startup after pinmuxing */

drivers/i2c/busses/i2c-ocores.c

@@ -10,40 +10,9 @@
  */
 
 /*
- * Device tree configuration:
- *
- * Required properties:
- * - compatible      : "opencores,i2c-ocores"
- * - reg             : bus address start and address range size of device
- * - interrupts      : interrupt number
- * - regstep         : size of device registers in bytes
- * - clock-frequency : frequency of bus clock in Hz
- * 
- * Example:
- *
- *  i2c0: ocores@a0000000 {
- *              compatible = "opencores,i2c-ocores";
- *              reg = <0xa0000000 0x8>;
- *              interrupts = <10>;
- *
- *              regstep = <1>;
- *              clock-frequency = <20000000>;
- *
- * -- Devices connected on this I2C bus get
- * -- defined here; address- and size-cells
- * -- apply to these child devices
- *
- *              #address-cells = <1>;
- *              #size-cells = <0>;
- *
- *              dummy@60 {
- *                     compatible = "dummy";
- *                     reg = <60>;
- *              };
- *  };
- *
+ * This driver can be used from the device tree, see
+ *     Documentation/devicetree/bindings/i2c/ocore-i2c.txt
  */
-
 #include <linux/kernel.h>
 #include <linux/module.h>
 #include <linux/init.h>
@@ -56,10 +25,12 @@
 #include <linux/slab.h>
 #include <linux/io.h>
 #include <linux/of_i2c.h>
+#include <linux/log2.h>
 
 struct ocores_i2c {
 	void __iomem *base;
-	int regstep;
+	u32 reg_shift;
+	u32 reg_io_width;
 	wait_queue_head_t wait;
 	struct i2c_adapter adap;
 	struct i2c_msg *msg;
@@ -102,12 +73,22 @@ struct ocores_i2c {
 
 static inline void oc_setreg(struct ocores_i2c *i2c, int reg, u8 value)
 {
-	iowrite8(value, i2c->base + reg * i2c->regstep);
+	if (i2c->reg_io_width == 4)
+		iowrite32(value, i2c->base + (reg << i2c->reg_shift));
+	else if (i2c->reg_io_width == 2)
+		iowrite16(value, i2c->base + (reg << i2c->reg_shift));
+	else
+		iowrite8(value, i2c->base + (reg << i2c->reg_shift));
 }
 
 static inline u8 oc_getreg(struct ocores_i2c *i2c, int reg)
 {
-	return ioread8(i2c->base + reg * i2c->regstep);
+	if (i2c->reg_io_width == 4)
+		return ioread32(i2c->base + (reg << i2c->reg_shift));
+	else if (i2c->reg_io_width == 2)
+		return ioread16(i2c->base + (reg << i2c->reg_shift));
+	else
+		return ioread8(i2c->base + (reg << i2c->reg_shift));
 }
 
 static void ocores_process(struct ocores_i2c *i2c)
@@ -247,26 +228,35 @@ static struct i2c_adapter ocores_adapter = {
 };
 
 #ifdef CONFIG_OF
-static int ocores_i2c_of_probe(struct platform_device* pdev,
-				struct ocores_i2c* i2c)
+static int ocores_i2c_of_probe(struct platform_device *pdev,
+				struct ocores_i2c *i2c)
 {
-	const __be32* val;
-
-	val = of_get_property(pdev->dev.of_node, "regstep", NULL);
-	if (!val) {
-		dev_err(&pdev->dev, "Missing required parameter 'regstep'");
-		return -ENODEV;
+	struct device_node *np = pdev->dev.of_node;
+	u32 val;
+
+	if (of_property_read_u32(np, "reg-shift", &i2c->reg_shift)) {
+		/* no 'reg-shift', check for deprecated 'regstep' */
+		if (!of_property_read_u32(np, "regstep", &val)) {
+			if (!is_power_of_2(val)) {
+				dev_err(&pdev->dev, "invalid regstep %d\n",
+					val);
+				return -EINVAL;
+			}
+			i2c->reg_shift = ilog2(val);
+			dev_warn(&pdev->dev,
+				"regstep property deprecated, use reg-shift\n");
+		}
 	}
-	i2c->regstep = be32_to_cpup(val);
 
-	val = of_get_property(pdev->dev.of_node, "clock-frequency", NULL);
-	if (!val) {
+	if (of_property_read_u32(np, "clock-frequency", &val)) {
 		dev_err(&pdev->dev,
-			"Missing required parameter 'clock-frequency'");
+			"Missing required parameter 'clock-frequency'\n");
 		return -ENODEV;
 	}
-	i2c->clock_khz = be32_to_cpup(val) / 1000;
+	i2c->clock_khz = val / 1000;
 
+	of_property_read_u32(pdev->dev.of_node, "reg-io-width",
+				&i2c->reg_io_width);
 	return 0;
 }
 #else
@@ -308,7 +298,8 @@ static int __devinit ocores_i2c_probe(struct platform_device *pdev)
 
 	pdata = pdev->dev.platform_data;
 	if (pdata) {
-		i2c->regstep = pdata->regstep;
+		i2c->reg_shift = pdata->reg_shift;
+		i2c->reg_io_width = pdata->reg_io_width;
 		i2c->clock_khz = pdata->clock_khz;
 	} else {
 		ret = ocores_i2c_of_probe(pdev, i2c);
@@ -316,6 +307,9 @@ static int __devinit ocores_i2c_probe(struct platform_device *pdev)
 			return ret;
 	}
 
+	if (i2c->reg_io_width == 0)
+		i2c->reg_io_width = 1; /* Set to default value */
+
 	ocores_init(i2c);
 
 	init_waitqueue_head(&i2c->wait);
@@ -351,7 +345,7 @@ static int __devinit ocores_i2c_probe(struct platform_device *pdev)
 	return 0;
 }
 
-static int __devexit ocores_i2c_remove(struct platform_device* pdev)
+static int __devexit ocores_i2c_remove(struct platform_device *pdev)
 {
 	struct ocores_i2c *i2c = platform_get_drvdata(pdev);
 
@@ -367,9 +361,9 @@ static int __devexit ocores_i2c_remove(struct platform_device* pdev)
 }
 
 #ifdef CONFIG_PM
-static int ocores_i2c_suspend(struct platform_device *pdev, pm_message_t state)
+static int ocores_i2c_suspend(struct device *dev)
 {
-	struct ocores_i2c *i2c = platform_get_drvdata(pdev);
+	struct ocores_i2c *i2c = dev_get_drvdata(dev);
 	u8 ctrl = oc_getreg(i2c, OCI2C_CONTROL);
 
 	/* make sure the device is disabled */
@@ -378,17 +372,19 @@ static int ocores_i2c_suspend(struct platform_device *pdev, pm_message_t state)
 	return 0;
 }
 
-static int ocores_i2c_resume(struct platform_device *pdev)
+static int ocores_i2c_resume(struct device *dev)
 {
-	struct ocores_i2c *i2c = platform_get_drvdata(pdev);
+	struct ocores_i2c *i2c = dev_get_drvdata(dev);
 
 	ocores_init(i2c);
 
 	return 0;
 }
+
+static SIMPLE_DEV_PM_OPS(ocores_i2c_pm, ocores_i2c_suspend, ocores_i2c_resume);
+#define OCORES_I2C_PM	(&ocores_i2c_pm)
 #else
-#define ocores_i2c_suspend	NULL
-#define ocores_i2c_resume	NULL
+#define OCORES_I2C_PM	NULL
 #endif
 
 static struct of_device_id ocores_i2c_match[] = {
@@ -400,12 +396,11 @@ MODULE_DEVICE_TABLE(of, ocores_i2c_match);
 static struct platform_driver ocores_i2c_driver = {
 	.probe   = ocores_i2c_probe,
 	.remove  = __devexit_p(ocores_i2c_remove),
-	.suspend = ocores_i2c_suspend,
-	.resume  = ocores_i2c_resume,
 	.driver  = {
 		.owner = THIS_MODULE,
 		.name = "ocores-i2c",
 		.of_match_table = ocores_i2c_match,
+		.pm = OCORES_I2C_PM,
 	},
 };
 

drivers/i2c/busses/i2c-pnx.c

@@ -587,25 +587,27 @@ static struct i2c_algorithm pnx_algorithm = {
 };
 
 #ifdef CONFIG_PM
-static int i2c_pnx_controller_suspend(struct platform_device *pdev,
-				      pm_message_t state)
+static int i2c_pnx_controller_suspend(struct device *dev)
 {
-	struct i2c_pnx_algo_data *alg_data = platform_get_drvdata(pdev);
+	struct i2c_pnx_algo_data *alg_data = dev_get_drvdata(dev);
 
 	clk_disable(alg_data->clk);
 
 	return 0;
 }
 
-static int i2c_pnx_controller_resume(struct platform_device *pdev)
+static int i2c_pnx_controller_resume(struct device *dev)
 {
-	struct i2c_pnx_algo_data *alg_data = platform_get_drvdata(pdev);
+	struct i2c_pnx_algo_data *alg_data = dev_get_drvdata(dev);
 
 	return clk_enable(alg_data->clk);
 }
+
+static SIMPLE_DEV_PM_OPS(i2c_pnx_pm,
+			 i2c_pnx_controller_suspend, i2c_pnx_controller_resume);
+#define PNX_I2C_PM	(&i2c_pnx_pm)
 #else
-#define i2c_pnx_controller_suspend	NULL
-#define i2c_pnx_controller_resume	NULL
+#define PNX_I2C_PM	NULL
 #endif
 
 static int __devinit i2c_pnx_probe(struct platform_device *pdev)
@@ -783,11 +785,10 @@ static struct platform_driver i2c_pnx_driver = {
 		.name = "pnx-i2c",
 		.owner = THIS_MODULE,
 		.of_match_table = of_match_ptr(i2c_pnx_of_match),
+		.pm = PNX_I2C_PM,
 	},
 	.probe = i2c_pnx_probe,
 	.remove = __devexit_p(i2c_pnx_remove),
-	.suspend = i2c_pnx_controller_suspend,
-	.resume = i2c_pnx_controller_resume,
 };
 
 static int __init i2c_adap_pnx_init(void)

drivers/i2c/busses/i2c-puv3.c

@@ -254,7 +254,7 @@ static int __devexit puv3_i2c_remove(struct platform_device *pdev)
 }
 
 #ifdef CONFIG_PM
-static int puv3_i2c_suspend(struct platform_device *dev, pm_message_t state)
+static int puv3_i2c_suspend(struct device *dev)
 {
 	int poll_count;
 	/* Disable the IIC */
@@ -267,23 +267,20 @@ static int puv3_i2c_suspend(struct platform_device *dev, pm_message_t state)
 	return 0;
 }
 
-static int puv3_i2c_resume(struct platform_device *dev)
-{
-	return 0 ;
-}
+static SIMPLE_DEV_PM_OPS(puv3_i2c_pm, puv3_i2c_suspend, NULL);
+#define PUV3_I2C_PM	(&puv3_i2c_pm)
+
 #else
-#define puv3_i2c_suspend NULL
-#define puv3_i2c_resume NULL
+#define PUV3_I2C_PM	NULL
 #endif
 
 static struct platform_driver puv3_i2c_driver = {
 	.probe		= puv3_i2c_probe,
 	.remove		= __devexit_p(puv3_i2c_remove),
-	.suspend	= puv3_i2c_suspend,
-	.resume		= puv3_i2c_resume,
 	.driver		= {
 		.name	= "PKUnity-v3-I2C",
 		.owner	= THIS_MODULE,
+		.pm	= PUV3_I2C_PM,
 	}
 };
 

drivers/i2c/busses/i2c-s3c2410.c

@@ -122,7 +122,7 @@ static inline unsigned int s3c24xx_get_device_quirks(struct platform_device *pde
 {
 	if (pdev->dev.of_node) {
 		const struct of_device_id *match;
-		match = of_match_node(&s3c24xx_i2c_match, pdev->dev.of_node);
+		match = of_match_node(s3c24xx_i2c_match, pdev->dev.of_node);
 		return (unsigned int)match->data;
 	}
 
@@ -609,7 +609,7 @@ static int s3c24xx_i2c_xfer(struct i2c_adapter *adap,
 
 		if (ret != -EAGAIN) {
 			clk_disable(i2c->clk);
-			pm_runtime_put_sync(&adap->dev);
+			pm_runtime_put(&adap->dev);
 			return ret;
 		}
 
@@ -619,7 +619,7 @@ static int s3c24xx_i2c_xfer(struct i2c_adapter *adap,
 	}
 
 	clk_disable(i2c->clk);
-	pm_runtime_put_sync(&adap->dev);
+	pm_runtime_put(&adap->dev);
 	return -EREMOTEIO;
 }
 

drivers/i2c/busses/i2c-stu300.c

 /*
- * Copyright (C) 2007-2009 ST-Ericsson AB
+ * Copyright (C) 2007-2012 ST-Ericsson AB
  * License terms: GNU General Public License (GPL) version 2
  * ST DDC I2C master mode driver, used in e.g. U300 series platforms.
  * Author: Linus Walleij <linus.walleij@stericsson.com>
@@ -139,8 +139,6 @@ module_param(scl_frequency, uint,  0644);
  * struct stu300_dev - the stu300 driver state holder
  * @pdev: parent platform device
  * @adapter: corresponding I2C adapter
- * @phybase: location of I/O area in memory
- * @physize: size of I/O area in memory
  * @clk: hardware block clock
  * @irq: assigned interrupt line
  * @cmd_issue_lock: this locks the following cmd_ variables
@@ -155,8 +153,6 @@ module_param(scl_frequency, uint,  0644);
 struct stu300_dev {
 	struct platform_device	*pdev;
 	struct i2c_adapter	adapter;
-	resource_size_t		phybase;
-	resource_size_t		physize;
 	void __iomem		*virtbase;
 	struct clk		*clk;
 	int			irq;
@@ -873,64 +869,44 @@ stu300_probe(struct platform_device *pdev)
 	int ret = 0;
 	char clk_name[] = "I2C0";
 
-	dev = kzalloc(sizeof(struct stu300_dev), GFP_KERNEL);
+	dev = devm_kzalloc(&pdev->dev, sizeof(struct stu300_dev), GFP_KERNEL);
 	if (!dev) {
 		dev_err(&pdev->dev, "could not allocate device struct\n");
-		ret = -ENOMEM;
-		goto err_no_devmem;
+		return -ENOMEM;
 	}
 
 	bus_nr = pdev->id;
 	clk_name[3] += (char)bus_nr;
-	dev->clk = clk_get(&pdev->dev, clk_name);
+	dev->clk = devm_clk_get(&pdev->dev, clk_name);
 	if (IS_ERR(dev->clk)) {
-		ret = PTR_ERR(dev->clk);
 		dev_err(&pdev->dev, "could not retrieve i2c bus clock\n");
-		goto err_no_clk;
+		return PTR_ERR(dev->clk);
 	}
 
 	dev->pdev = pdev;
-	platform_set_drvdata(pdev, dev);
-
 	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-	if (!res) {
-		ret = -ENOENT;
-		goto err_no_resource;
-	}
-
-	dev->phybase = res->start;
-	dev->physize = resource_size(res);
-
-	if (request_mem_region(dev->phybase, dev->physize,
-			       NAME " I/O Area") == NULL) {
-		ret = -EBUSY;
-		goto err_no_ioregion;
-	}
+	if (!res)
+		return -ENOENT;
 
-	dev->virtbase = ioremap(dev->phybase, dev->physize);
+	dev->virtbase = devm_request_and_ioremap(&pdev->dev, res);
 	dev_dbg(&pdev->dev, "initialize bus device I2C%d on virtual "
 		"base %p\n", bus_nr, dev->virtbase);
-	if (!dev->virtbase) {
-		ret = -ENOMEM;
-		goto err_no_ioremap;
-	}
+	if (!dev->virtbase)
+		return -ENOMEM;
 
 	dev->irq = platform_get_irq(pdev, 0);
-	if (request_irq(dev->irq, stu300_irh, 0,
-			NAME, dev)) {
-		ret = -EIO;
-		goto err_no_irq;
-	}
+	ret = devm_request_irq(&pdev->dev, dev->irq, stu300_irh, 0, NAME, dev);
+	if (ret < 0)
+		return ret;
 
 	dev->speed = scl_frequency;
 
-	clk_enable(dev->clk);
+	clk_prepare_enable(dev->clk);
 	ret = stu300_init_hw(dev);
 	clk_disable(dev->clk);
-
 	if (ret != 0) {
 		dev_err(&dev->pdev->dev, "error initializing hardware.\n");
-		goto err_init_hw;
+		return -EIO;
 	}
 
 	/* IRQ event handling initialization */
@@ -952,57 +928,43 @@ stu300_probe(struct platform_device *pdev)
 	/* i2c device drivers may be active on return from add_adapter() */
 	ret = i2c_add_numbered_adapter(adap);
 	if (ret) {
-		dev_err(&dev->pdev->dev, "failure adding ST Micro DDC "
+		dev_err(&pdev->dev, "failure adding ST Micro DDC "
 		       "I2C adapter\n");
-		goto err_add_adapter;
+		return ret;
 	}
-	return 0;
 
- err_add_adapter:
- err_init_hw:
-	free_irq(dev->irq, dev);
- err_no_irq:
-	iounmap(dev->virtbase);
- err_no_ioremap:
-	release_mem_region(dev->phybase, dev->physize);
- err_no_ioregion:
-	platform_set_drvdata(pdev, NULL);
- err_no_resource:
-	clk_put(dev->clk);
- err_no_clk:
-	kfree(dev);
- err_no_devmem:
-	dev_err(&pdev->dev, "failed to add " NAME " adapter: %d\n",
-		pdev->id);
-	return ret;
+	platform_set_drvdata(pdev, dev);
+	return 0;
 }
 
 #ifdef CONFIG_PM
-static int stu300_suspend(struct platform_device *pdev, pm_message_t state)
+static int stu300_suspend(struct device *device)
 {
-	struct stu300_dev *dev = platform_get_drvdata(pdev);
+	struct stu300_dev *dev = dev_get_drvdata(device);
 
 	/* Turn off everything */
 	stu300_wr8(0x00, dev->virtbase + I2C_CR);
 	return 0;
 }
 
-static int stu300_resume(struct platform_device *pdev)
+static int stu300_resume(struct device *device)
 {
 	int ret = 0;
-	struct stu300_dev *dev = platform_get_drvdata(pdev);
+	struct stu300_dev *dev = dev_get_drvdata(device);
 
 	clk_enable(dev->clk);
 	ret = stu300_init_hw(dev);
 	clk_disable(dev->clk);
 
 	if (ret != 0)
-		dev_err(&pdev->dev, "error re-initializing hardware.\n");
+		dev_err(device, "error re-initializing hardware.\n");
 	return ret;
 }
+
+static SIMPLE_DEV_PM_OPS(stu300_pm, stu300_suspend, stu300_resume);
+#define STU300_I2C_PM	(&stu300_pm)
 #else
-#define stu300_suspend NULL
-#define stu300_resume NULL
+#define STU300_I2C_PM	NULL
 #endif
 
 static int __exit
@@ -1013,12 +975,7 @@ stu300_remove(struct platform_device *pdev)
 	i2c_del_adapter(&dev->adapter);
 	/* Turn off everything */
 	stu300_wr8(0x00, dev->virtbase + I2C_CR);
-	free_irq(dev->irq, dev);
-	iounmap(dev->virtbase);
-	release_mem_region(dev->phybase, dev->physize);
-	clk_put(dev->clk);
 	platform_set_drvdata(pdev, NULL);
-	kfree(dev);
 	return 0;
 }
 
@@ -1026,10 +983,9 @@ static struct platform_driver stu300_i2c_driver = {
 	.driver = {
 		.name	= NAME,
 		.owner	= THIS_MODULE,
+		.pm	= STU300_I2C_PM,
 	},
 	.remove		= __exit_p(stu300_remove),
-	.suspend        = stu300_suspend,
-	.resume         = stu300_resume,
 
 };
 

drivers/i2c/busses/i2c-tegra.c

@@ -97,8 +97,21 @@
 #define I2C_HEADER_10BIT_ADDR			(1<<18)
 #define I2C_HEADER_IE_ENABLE			(1<<17)
 #define I2C_HEADER_REPEAT_START			(1<<16)
+#define I2C_HEADER_CONTINUE_XFER		(1<<15)
 #define I2C_HEADER_MASTER_ADDR_SHIFT		12
 #define I2C_HEADER_SLAVE_ADDR_SHIFT		1
+/*
+ * msg_end_type: The bus control which need to be send at end of transfer.
+ * @MSG_END_STOP: Send stop pulse at end of transfer.
+ * @MSG_END_REPEAT_START: Send repeat start at end of transfer.
+ * @MSG_END_CONTINUE: The following on message is coming and so do not send
+ *		stop or repeat start.
+ */
+enum msg_end_type {
+	MSG_END_STOP,
+	MSG_END_REPEAT_START,
+	MSG_END_CONTINUE,
+};
 
 /**
  * struct tegra_i2c_dev	- per device i2c context
@@ -106,7 +119,6 @@
  * @adapter: core i2c layer adapter information
  * @clk: clock reference for i2c controller
  * @i2c_clk: clock reference for i2c bus
- * @iomem: memory resource for registers
  * @base: ioremapped registers cookie
  * @cont_id: i2c controller id, used for for packet header
  * @irq: irq number of transfer complete interrupt
@@ -124,7 +136,6 @@ struct tegra_i2c_dev {
 	struct i2c_adapter adapter;
 	struct clk *clk;
 	struct clk *i2c_clk;
-	struct resource *iomem;
 	void __iomem *base;
 	int cont_id;
 	int irq;
@@ -165,6 +176,10 @@ static void i2c_writel(struct tegra_i2c_dev *i2c_dev, u32 val,
 	unsigned long reg)
 {
 	writel(val, i2c_dev->base + tegra_i2c_reg_addr(i2c_dev, reg));
+
+	/* Read back register to make sure that register writes completed */
+	if (reg != I2C_TX_FIFO)
+		readl(i2c_dev->base + tegra_i2c_reg_addr(i2c_dev, reg));
 }
 
 static u32 i2c_readl(struct tegra_i2c_dev *i2c_dev, unsigned long reg)
@@ -449,7 +464,7 @@ static irqreturn_t tegra_i2c_isr(int irq, void *dev_id)
 }
 
 static int tegra_i2c_xfer_msg(struct tegra_i2c_dev *i2c_dev,
-	struct i2c_msg *msg, int stop)
+	struct i2c_msg *msg, enum msg_end_type end_state)
 {
 	u32 packet_header;
 	u32 int_mask;
@@ -476,7 +491,9 @@ static int tegra_i2c_xfer_msg(struct tegra_i2c_dev *i2c_dev,
 	i2c_writel(i2c_dev, packet_header, I2C_TX_FIFO);
 
 	packet_header = I2C_HEADER_IE_ENABLE;
-	if (!stop)
+	if (end_state == MSG_END_CONTINUE)
+		packet_header |= I2C_HEADER_CONTINUE_XFER;
+	else if (end_state == MSG_END_REPEAT_START)
 		packet_header |= I2C_HEADER_REPEAT_START;
 	if (msg->flags & I2C_M_TEN) {
 		packet_header |= msg->addr;
@@ -548,8 +565,14 @@ static int tegra_i2c_xfer(struct i2c_adapter *adap, struct i2c_msg msgs[],
 
 	clk_prepare_enable(i2c_dev->clk);
 	for (i = 0; i < num; i++) {
-		int stop = (i == (num - 1)) ? 1  : 0;
-		ret = tegra_i2c_xfer_msg(i2c_dev, &msgs[i], stop);
+		enum msg_end_type end_type = MSG_END_STOP;
+		if (i < (num - 1)) {
+			if (msgs[i + 1].flags & I2C_M_NOSTART)
+				end_type = MSG_END_CONTINUE;
+			else
+				end_type = MSG_END_REPEAT_START;
+		}
+		ret = tegra_i2c_xfer_msg(i2c_dev, &msgs[i], end_type);
 		if (ret)
 			break;
 	}
@@ -559,7 +582,8 @@ static int tegra_i2c_xfer(struct i2c_adapter *adap, struct i2c_msg msgs[],
 
 static u32 tegra_i2c_func(struct i2c_adapter *adap)
 {
-	return I2C_FUNC_I2C | I2C_FUNC_SMBUS_EMUL | I2C_FUNC_10BIT_ADDR;
+	return I2C_FUNC_I2C | I2C_FUNC_SMBUS_EMUL | I2C_FUNC_10BIT_ADDR |
+		I2C_FUNC_PROTOCOL_MANGLING | I2C_FUNC_NOSTART;
 }
 
 static const struct i2c_algorithm tegra_i2c_algo = {
@@ -572,7 +596,6 @@ static int __devinit tegra_i2c_probe(struct platform_device *pdev)
 	struct tegra_i2c_dev *i2c_dev;
 	struct tegra_i2c_platform_data *pdata = pdev->dev.platform_data;
 	struct resource *res;
-	struct resource *iomem;
 	struct clk *clk;
 	struct clk *i2c_clk;
 	const unsigned int *prop;
@@ -585,50 +608,41 @@ static int __devinit tegra_i2c_probe(struct platform_device *pdev)
 		dev_err(&pdev->dev, "no mem resource\n");
 		return -EINVAL;
 	}
-	iomem = request_mem_region(res->start, resource_size(res), pdev->name);
-	if (!iomem) {
-		dev_err(&pdev->dev, "I2C region already claimed\n");
-		return -EBUSY;
-	}
 
-	base = ioremap(iomem->start, resource_size(iomem));
+	base = devm_request_and_ioremap(&pdev->dev, res);
 	if (!base) {
-		dev_err(&pdev->dev, "Cannot ioremap I2C region\n");
-		return -ENOMEM;
+		dev_err(&pdev->dev, "Cannot request/ioremap I2C registers\n");
+		return -EADDRNOTAVAIL;
 	}
 
 	res = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
 	if (!res) {
 		dev_err(&pdev->dev, "no irq resource\n");
-		ret = -EINVAL;
-		goto err_iounmap;
+		return -EINVAL;
 	}
 	irq = res->start;
 
-	clk = clk_get(&pdev->dev, NULL);
+	clk = devm_clk_get(&pdev->dev, NULL);
 	if (IS_ERR(clk)) {
 		dev_err(&pdev->dev, "missing controller clock");
-		ret = PTR_ERR(clk);
-		goto err_release_region;
+		return PTR_ERR(clk);
 	}
 
-	i2c_clk = clk_get(&pdev->dev, "i2c");
+	i2c_clk = devm_clk_get(&pdev->dev, "i2c");
 	if (IS_ERR(i2c_clk)) {
 		dev_err(&pdev->dev, "missing bus clock");
-		ret = PTR_ERR(i2c_clk);
-		goto err_clk_put;
+		return PTR_ERR(i2c_clk);
 	}
 
-	i2c_dev = kzalloc(sizeof(struct tegra_i2c_dev), GFP_KERNEL);
+	i2c_dev = devm_kzalloc(&pdev->dev, sizeof(*i2c_dev), GFP_KERNEL);
 	if (!i2c_dev) {
-		ret = -ENOMEM;
-		goto err_i2c_clk_put;
+		dev_err(&pdev->dev, "Could not allocate struct tegra_i2c_dev");
+		return -ENOMEM;
 	}
 
 	i2c_dev->base = base;
 	i2c_dev->clk = clk;
 	i2c_dev->i2c_clk = i2c_clk;
-	i2c_dev->iomem = iomem;
 	i2c_dev->adapter.algo = &tegra_i2c_algo;
 	i2c_dev->irq = irq;
 	i2c_dev->cont_id = pdev->id;
@@ -657,13 +671,14 @@ static int __devinit tegra_i2c_probe(struct platform_device *pdev)
 	ret = tegra_i2c_init(i2c_dev);
 	if (ret) {
 		dev_err(&pdev->dev, "Failed to initialize i2c controller");
-		goto err_free;
+		return ret;
 	}
 
-	ret = request_irq(i2c_dev->irq, tegra_i2c_isr, 0, pdev->name, i2c_dev);
+	ret = devm_request_irq(&pdev->dev, i2c_dev->irq,
+			tegra_i2c_isr, 0, pdev->name, i2c_dev);
 	if (ret) {
 		dev_err(&pdev->dev, "Failed to request irq %i\n", i2c_dev->irq);
-		goto err_free;
+		return ret;
 	}
 
 	clk_prepare_enable(i2c_dev->i2c_clk);
@@ -681,45 +696,26 @@ static int __devinit tegra_i2c_probe(struct platform_device *pdev)
 	ret = i2c_add_numbered_adapter(&i2c_dev->adapter);
 	if (ret) {
 		dev_err(&pdev->dev, "Failed to add I2C adapter\n");
-		goto err_free_irq;
+		clk_disable_unprepare(i2c_dev->i2c_clk);
+		return ret;
 	}
 
 	of_i2c_register_devices(&i2c_dev->adapter);
 
 	return 0;
-err_free_irq:
-	free_irq(i2c_dev->irq, i2c_dev);
-err_free:
-	kfree(i2c_dev);
-err_i2c_clk_put:
-	clk_put(i2c_clk);
-err_clk_put:
-	clk_put(clk);
-err_release_region:
-	release_mem_region(iomem->start, resource_size(iomem));
-err_iounmap:
-	iounmap(base);
-	return ret;
 }
 
 static int __devexit tegra_i2c_remove(struct platform_device *pdev)
 {
 	struct tegra_i2c_dev *i2c_dev = platform_get_drvdata(pdev);
 	i2c_del_adapter(&i2c_dev->adapter);
-	free_irq(i2c_dev->irq, i2c_dev);
-	clk_put(i2c_dev->i2c_clk);
-	clk_put(i2c_dev->clk);
-	release_mem_region(i2c_dev->iomem->start,
-		resource_size(i2c_dev->iomem));
-	iounmap(i2c_dev->base);
-	kfree(i2c_dev);
 	return 0;
 }
 
 #ifdef CONFIG_PM
-static int tegra_i2c_suspend(struct platform_device *pdev, pm_message_t state)
+static int tegra_i2c_suspend(struct device *dev)
 {
-	struct tegra_i2c_dev *i2c_dev = platform_get_drvdata(pdev);
+	struct tegra_i2c_dev *i2c_dev = dev_get_drvdata(dev);
 
 	i2c_lock_adapter(&i2c_dev->adapter);
 	i2c_dev->is_suspended = true;
@@ -728,9 +724,9 @@ static int tegra_i2c_suspend(struct platform_device *pdev, pm_message_t state)
 	return 0;
 }
 
-static int tegra_i2c_resume(struct platform_device *pdev)
+static int tegra_i2c_resume(struct device *dev)
 {
-	struct tegra_i2c_dev *i2c_dev = platform_get_drvdata(pdev);
+	struct tegra_i2c_dev *i2c_dev = dev_get_drvdata(dev);
 	int ret;
 
 	i2c_lock_adapter(&i2c_dev->adapter);
@@ -748,6 +744,11 @@ static int tegra_i2c_resume(struct platform_device *pdev)
 
 	return 0;
 }
+
+static SIMPLE_DEV_PM_OPS(tegra_i2c_pm, tegra_i2c_suspend, tegra_i2c_resume);
+#define TEGRA_I2C_PM	(&tegra_i2c_pm)
+#else
+#define TEGRA_I2C_PM	NULL
 #endif
 
 #if defined(CONFIG_OF)
@@ -758,21 +759,16 @@ static const struct of_device_id tegra_i2c_of_match[] __devinitconst = {
 	{},
 };
 MODULE_DEVICE_TABLE(of, tegra_i2c_of_match);
-#else
-#define tegra_i2c_of_match NULL
 #endif
 
 static struct platform_driver tegra_i2c_driver = {
 	.probe   = tegra_i2c_probe,
 	.remove  = __devexit_p(tegra_i2c_remove),
-#ifdef CONFIG_PM
-	.suspend = tegra_i2c_suspend,
-	.resume  = tegra_i2c_resume,
-#endif
 	.driver  = {
 		.name  = "tegra-i2c",
 		.owner = THIS_MODULE,
-		.of_match_table = tegra_i2c_of_match,
+		.of_match_table = of_match_ptr(tegra_i2c_of_match),
+		.pm    = TEGRA_I2C_PM,
 	},
 };
 

drivers/mfd/timberdale.c

@@ -83,7 +83,7 @@ timberdale_xiic_platform_data = {
 
 static __devinitdata struct ocores_i2c_platform_data
 timberdale_ocores_platform_data = {
-	.regstep = 4,
+	.reg_shift = 2,
 	.clock_khz = 62500,
 	.devices = timberdale_i2c_board_info,
 	.num_devices = ARRAY_SIZE(timberdale_i2c_board_info)

include/linux/i2c-ocores.h

@@ -12,7 +12,8 @@
 #define _LINUX_I2C_OCORES_H
 
 struct ocores_i2c_platform_data {
-	u32 regstep;   /* distance between registers */
+	u32 reg_shift; /* register offset shift value */
+	u32 reg_io_width; /* register io read/write width */
 	u32 clock_khz; /* input clock in kHz */
 	u8 num_devices; /* number of devices in the devices list */
 	struct i2c_board_info const *devices; /* devices connected to the bus */

arch/arm/plat-nomadik/include/plat/i2c.h → include/linux/platform_data/i2c-nomadik.h

@@ -5,8 +5,8 @@
  * it under the terms of the GNU General Public License version 2, as
  * published by the Free Software Foundation.
  */
-#ifndef __PLAT_I2C_H
-#define __PLAT_I2C_H
+#ifndef __PDATA_I2C_NOMADIK_H
+#define __PDATA_I2C_NOMADIK_H
 
 enum i2c_freq_mode {
 	I2C_FREQ_MODE_STANDARD,		/* up to 100 Kb/s */
@@ -36,4 +36,4 @@ struct nmk_i2c_controller {
 	enum i2c_freq_mode	sm;
 };
 
-#endif	/* __PLAT_I2C_H */
+#endif	/* __PDATA_I2C_NOMADIK_H */