ARM: orion5x: use DT to describe NOR on edmini_v2

This commit converts the already partially DT-converted edmini_v2
platform to use the Device Tree for NOR flash, using the Device Bus.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Link: https://lkml.kernel.org/r/1398202002-28530-32-git-send-email-thomas.petazzoni@free-electrons.comSigned-off-by: Jason Cooper <jason@lakedaemon.net>

arch/arm/boot/dts/orion5x-lacie-ethernet-disk-mini-v2.dts

@@ -28,7 +28,8 @@ chosen {
 
 	soc {
 		ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000>,
-			 <MBUS_ID(0x09, 0x00) 0 0xf2200000 0x800>;
+			 <MBUS_ID(0x09, 0x00) 0 0xf2200000 0x800>,
+			 <MBUS_ID(0x01, 0x0f) 0 0xfff80000 0x80000>;
 	};
 
 	gpio-keys {
@@ -56,6 +57,46 @@ led@1 {
 	};
 };
 
+&devbus_bootcs {
+	status = "okay";
+
+	/* Read parameters */
+	devbus,bus-width    = <8>;
+	devbus,turn-off-ps  = <90000>;
+	devbus,badr-skew-ps = <0>;
+	devbus,acc-first-ps = <186000>;
+	devbus,acc-next-ps  = <186000>;
+
+	/* Write parameters */
+	devbus,wr-high-ps  = <90000>;
+	devbus,wr-low-ps   = <90000>;
+	devbus,ale-wr-ps   = <90000>;
+
+	/*
+	 * Currently the MTD code does not recognize the MX29LV400CBCT
+	 * as a bottom-type device. This could cause risks of
+	 * accidentally erasing critical flash sectors. We thus define
+	 * a single, write-protected partition covering the whole
+	 * flash.  TODO: once the flash part TOP/BOTTOM detection
+	 * issue is sorted out in the MTD code, break this into at
+	 * least three partitions: 'u-boot code', 'u-boot environment'
+	 * and 'whatever is left'.
+	 */
+	flash@0 {
+		compatible = "cfi-flash";
+		reg = <0 0x80000>;
+		bank-width = <1>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		partition@0 {
+			label = "Full512Kb";
+			reg = <0 0x80000>;
+			read-only;
+		};
+	};
+};
+
 &ehci0 {
 	status = "okay";
 };

arch/arm/mach-orion5x/edmini_v2-setup.c

@@ -42,74 +42,12 @@
  * EDMINI_V2 Info
  ****************************************************************************/
 
-/*
- * 512KB NOR flash Device bus boot chip select
- */
-
-#define EDMINI_V2_NOR_BOOT_BASE		0xfff80000
-#define EDMINI_V2_NOR_BOOT_SIZE		SZ_512K
-
-/*****************************************************************************
- * 512KB NOR Flash on BOOT Device
- ****************************************************************************/
-
-/*
- * Currently the MTD code does not recognize the MX29LV400CBCT as a bottom
- * -type device. This could cause risks of accidentally erasing critical
- * flash sectors. We thus define a single, write-protected partition covering
- * the whole flash.
- * TODO: once the flash part TOP/BOTTOM detection issue is sorted out in the MTD
- * code, break this into at least three partitions: 'u-boot code', 'u-boot
- * environment' and 'whatever is left'.
- */
-
-static struct mtd_partition edmini_v2_partitions[] = {
-	{
-		.name		= "Full512kb",
-		.size		= 0x00080000,
-		.offset		= 0x00000000,
-		.mask_flags	= MTD_WRITEABLE,
-	},
-};
-
-static struct physmap_flash_data edmini_v2_nor_flash_data = {
-	.width		= 1,
-	.parts		= edmini_v2_partitions,
-	.nr_parts	= ARRAY_SIZE(edmini_v2_partitions),
-};
-
-static struct resource edmini_v2_nor_flash_resource = {
-	.flags			= IORESOURCE_MEM,
-	.start			= EDMINI_V2_NOR_BOOT_BASE,
-	.end			= EDMINI_V2_NOR_BOOT_BASE
-		+ EDMINI_V2_NOR_BOOT_SIZE - 1,
-};
-
-static struct platform_device edmini_v2_nor_flash = {
-	.name			= "physmap-flash",
-	.id			= 0,
-	.dev		= {
-		.platform_data	= &edmini_v2_nor_flash_data,
-	},
-	.num_resources		= 1,
-	.resource		= &edmini_v2_nor_flash_resource,
-};
-
 /*****************************************************************************
  * General Setup
  ****************************************************************************/
 
 void __init edmini_v2_init(void)
 {
-	/*
-	 * Configure peripherals.
-	 */
-	mvebu_mbus_add_window_by_id(ORION_MBUS_DEVBUS_BOOT_TARGET,
-				    ORION_MBUS_DEVBUS_BOOT_ATTR,
-				    EDMINI_V2_NOR_BOOT_BASE,
-				    EDMINI_V2_NOR_BOOT_SIZE);
-	platform_device_register(&edmini_v2_nor_flash);
-
 	pr_notice("edmini_v2: USB device port, flash write and power-off "
 		  "are not yet supported.\n");
 }