USB: Add call to notify xHC of a device reset.

Add a new host controller driver method, reset_device(), that the USB core
will use to notify the host of a successful device reset.  The call may
fail due to out-of-memory errors; attempt the port reset sequence again if
that happens.  Update hub_port_init() to allow resetting a configured
device.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

drivers/usb/core/hcd.h

@@ -286,6 +286,7 @@ struct hc_driver {
 		 */
 	int	(*update_hub_device)(struct usb_hcd *, struct usb_device *hdev,
 			struct usb_tt *tt, gfp_t mem_flags);
+	int	(*reset_device)(struct usb_hcd *, struct usb_device *);
 };
 
 extern int usb_hcd_link_urb_to_ep(struct usb_hcd *hcd, struct urb *urb);

drivers/usb/core/hub.c

@@ -2008,7 +2008,9 @@ static int hub_port_reset(struct usb_hub *hub, int port1,
 				struct usb_device *udev, unsigned int delay)
 {
 	int i, status;
+	struct usb_hcd *hcd;
 
+	hcd = bus_to_hcd(udev->bus);
 	/* Block EHCI CF initialization during the port reset.
 	 * Some companion controllers don't like it when they mix.
 	 */
@@ -2036,6 +2038,14 @@ static int hub_port_reset(struct usb_hub *hub, int port1,
 			/* TRSTRCY = 10 ms; plus some extra */
 			msleep(10 + 40);
 			update_address(udev, 0);
+			if (hcd->driver->reset_device) {
+				status = hcd->driver->reset_device(hcd, udev);
+				if (status < 0) {
+					dev_err(&udev->dev, "Cannot reset "
+							"HCD device state\n");
+					break;
+				}
+			}
 			/* FALL THROUGH */
 		case -ENOTCONN:
 		case -ENODEV:
@@ -2645,14 +2655,7 @@ hub_port_init (struct usb_hub *hub, struct usb_device *udev, int port1,
 
 	mutex_lock(&usb_address0_mutex);
 
-	if ((hcd->driver->flags & HCD_USB3) && udev->config) {
-		/* FIXME this will need special handling by the xHCI driver. */
-		dev_dbg(&udev->dev,
-				"xHCI reset of configured device "
-				"not supported yet.\n");
-		retval = -EINVAL;
-		goto fail;
-	} else if (!udev->config && oldspeed == USB_SPEED_SUPER) {
+	if (!udev->config && oldspeed == USB_SPEED_SUPER) {
 		/* Don't reset USB 3.0 devices during an initial setup */
 		usb_set_device_state(udev, USB_STATE_DEFAULT);
 	} else {

drivers/usb/host/xhci-pci.c

@@ -139,6 +139,7 @@ static const struct hc_driver xhci_pci_hc_driver = {
 	.reset_bandwidth =	xhci_reset_bandwidth,
 	.address_device =	xhci_address_device,
 	.update_hub_device =	xhci_update_hub_device,
+	.reset_device =		xhci_reset_device,
 
 	/*
 	 * scheduling support

drivers/usb/host/xhci.h

@@ -1270,6 +1270,7 @@ int xhci_urb_dequeue(struct usb_hcd *hcd, struct urb *urb, int status);
 int xhci_add_endpoint(struct usb_hcd *hcd, struct usb_device *udev, struct usb_host_endpoint *ep);
 int xhci_drop_endpoint(struct usb_hcd *hcd, struct usb_device *udev, struct usb_host_endpoint *ep);
 void xhci_endpoint_reset(struct usb_hcd *hcd, struct usb_host_endpoint *ep);
+int xhci_reset_device(struct usb_hcd *hcd, struct usb_device *udev);
 int xhci_check_bandwidth(struct usb_hcd *hcd, struct usb_device *udev);
 void xhci_reset_bandwidth(struct usb_hcd *hcd, struct usb_device *udev);