Commit a74022a5 authored by Lars-Peter Clausen's avatar Lars-Peter Clausen Committed by Greg Kroah-Hartman

USB: s3c2410_udc: Add common implementation for GPIO controlled pullups

Currently all boards using the s3c2410_udc driver use a GPIO to control the
state of the pullup, as a result the same code is reimplemented in each board
file.
This patch adds support for using a GPIO to control the pullup state to the udc
driver, so the boards can use a common implementation.
Signed-off-by: default avatarLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: default avatarGreg Kroah-Hartman <gregkh@suse.de>
parent 09173b58
......@@ -27,6 +27,10 @@ enum s3c2410_udc_cmd_e {
struct s3c2410_udc_mach_info {
void (*udc_command)(enum s3c2410_udc_cmd_e);
void (*vbus_draw)(unsigned int ma);
unsigned int pullup_pin;
unsigned int pullup_pin_inverted;
unsigned int vbus_pin;
unsigned char vbus_pin_inverted;
};
......
......@@ -1481,7 +1481,9 @@ static int s3c2410_udc_set_pullup(struct s3c2410_udc *udc, int is_on)
{
dprintk(DEBUG_NORMAL, "%s()\n", __func__);
if (udc_info && udc_info->udc_command) {
if (udc_info && (udc_info->udc_command ||
gpio_is_valid(udc_info->pullup_pin))) {
if (is_on)
s3c2410_udc_enable(udc);
else {
......@@ -1558,6 +1560,32 @@ static const struct usb_gadget_ops s3c2410_ops = {
.vbus_draw = s3c2410_vbus_draw,
};
static void s3c2410_udc_command(enum s3c2410_udc_cmd_e cmd)
{
if (!udc_info)
return;
if (udc_info->udc_command) {
udc_info->udc_command(S3C2410_UDC_P_DISABLE);
} else if (gpio_is_valid(udc_info->pullup_pin)) {
int value;
switch (cmd) {
case S3C2410_UDC_P_ENABLE:
value = 1;
break;
case S3C2410_UDC_P_DISABLE:
value = 0;
break;
default:
return;
}
value ^= udc_info->pullup_pin_inverted;
gpio_set_value(udc_info->pullup_pin, value);
}
}
/*------------------------- gadget driver handling---------------------------*/
/*
* s3c2410_udc_disable
......@@ -1579,8 +1607,7 @@ static void s3c2410_udc_disable(struct s3c2410_udc *dev)
udc_write(0x1F, S3C2410_UDC_EP_INT_REG);
/* Good bye, cruel world */
if (udc_info && udc_info->udc_command)
udc_info->udc_command(S3C2410_UDC_P_DISABLE);
s3c2410_udc_command(S3C2410_UDC_P_DISABLE);
/* Set speed to unknown */
dev->gadget.speed = USB_SPEED_UNKNOWN;
......@@ -1641,8 +1668,7 @@ static void s3c2410_udc_enable(struct s3c2410_udc *dev)
udc_write(S3C2410_UDC_INT_EP0, S3C2410_UDC_EP_INT_EN_REG);
/* time to say "hello, world" */
if (udc_info && udc_info->udc_command)
udc_info->udc_command(S3C2410_UDC_P_ENABLE);
s3c2410_udc_command(S3C2410_UDC_P_ENABLE);
}
/*
......@@ -1917,6 +1943,17 @@ static int s3c2410_udc_probe(struct platform_device *pdev)
udc->vbus = 1;
}
if (udc_info && !udc_info->udc_command &&
gpio_is_valid(udc_info->pullup_pin)) {
retval = gpio_request_one(udc_info->pullup_pin,
udc_info->vbus_pin_inverted ?
GPIOF_OUT_INIT_HIGH : GPIOF_OUT_INIT_LOW,
"udc pullup");
if (retval)
goto err_vbus_irq;
}
if (s3c2410_udc_debugfs_root) {
udc->regs_info = debugfs_create_file("registers", S_IRUGO,
s3c2410_udc_debugfs_root,
......@@ -1929,6 +1966,9 @@ static int s3c2410_udc_probe(struct platform_device *pdev)
return 0;
err_vbus_irq:
if (udc_info && udc_info->vbus_pin > 0)
free_irq(gpio_to_irq(udc_info->vbus_pin), udc);
err_gpio_claim:
if (udc_info && udc_info->vbus_pin > 0)
gpio_free(udc_info->vbus_pin);
......@@ -1956,6 +1996,10 @@ static int s3c2410_udc_remove(struct platform_device *pdev)
debugfs_remove(udc->regs_info);
if (udc_info && !udc_info->udc_command &&
gpio_is_valid(udc_info->pullup_pin))
gpio_free(udc_info->pullup_pin);
if (udc_info && udc_info->vbus_pin > 0) {
irq = gpio_to_irq(udc_info->vbus_pin);
free_irq(irq, udc);
......@@ -1987,16 +2031,14 @@ static int s3c2410_udc_remove(struct platform_device *pdev)
#ifdef CONFIG_PM
static int s3c2410_udc_suspend(struct platform_device *pdev, pm_message_t message)
{
if (udc_info && udc_info->udc_command)
udc_info->udc_command(S3C2410_UDC_P_DISABLE);
s3c2410_udc_command(S3C2410_UDC_P_DISABLE);
return 0;
}
static int s3c2410_udc_resume(struct platform_device *pdev)
{
if (udc_info && udc_info->udc_command)
udc_info->udc_command(S3C2410_UDC_P_ENABLE);
s3c2410_udc_command(S3C2410_UDC_P_ENABLE);
return 0;
}
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment