[ARM] Add Xscale ADIFCC and IOP310 documentation.

Documentation/arm/XScale/ADIFCC/80200EVB

+
+Board Overview
+-----------------------------
+
+This is an beta release of the Xscale Linux port to the ADI 80200EVB
+evaluation board.
+
+The 80200EVB is an evaluation platform for ADI Engineering's high-performance
+80200FCC chipset for the Intel 80200 XScale CPU. The 80200FCC is an open
+source FPGA based system that contains a PCI unit and a high performance
+memory controller.
+
+In addition to the 80200FCC, the board also contains a 16C550 UART, and 4MB
+of flash.
+
+The board is still under development and currently only the UART is functional
+as the PCI bits have not been programmed into the FPGA.
+
+For more information on the board, see http://www.adiengineering.com
+
+Port Status
+-----------------------------
+
+Supported:
+
+- Onboard UART (Polled operation only)
+- Cache/TLB locking on 80200 CPU
+
+TODO:
+
+- PCI when hardware supports it
+
+Building the Kernel
+-----------------------------
+change Linux makefile
+make adi_evb_config
+make oldconfig
+make dep
+make zImage
+
+Loading Linux
+-----------------------------
+
+Before you can use Linux on the ADI board, you need to grab the following:
+
+ADI 80200EVB Monitor:
+	ftp://source.mvista.com/pub/xscale/ADI_EVB/monitor.srec
+
+ADI JFFS2 Image:
+	ftp://source.mvista.com/pub/xscale/ADI_EVB/adi.jffs2
+
+Once you've got the Cygnus prompt, type in the following command:
+
+	load
+
+On another terminal window:
+
+	cat monitor.srec > /dev/ttyS0
+
+(replace ttyS0 with the serial port you are using)
+
+Once completed, just type 'go' at the cygmon prompt and you should see:
+
+	MontaVista IQ80310 Monitor Version 0.1
+	monitor>
+
+Type 'b 115200' at the prompt and change your terminal speed to 115200
+
+The first thing to do is to upload and burn the jffs2 filesystem image
+onto the boards 4MB of flash:
+
+	monitor> u c1000000
+	Uploading file at 0xc1000000
+	Now send file with ymodem
+
+Do as the monitor says and transfer the file adi.jffs2.  Once complete,
+the following will copy the jffs2 image to location 0x80000 in the flash.
+
+	monitor> f 8000 c1000000 200000
+	Erasing sector 0x00080000
+	Writing sector 0x00080000 with data at 0xC1000000
+	Erasing sector 0x000A0000
+	Writing sector 0x000A0000 with data at 0xC1020000
+	Erasing sector 0x000C0000
+	...
+
+Now use the same command as above to upload your zImage to location c1000000.
+When you've done that, type 'j c1000000' to run Linux.  Login as
+root and you're all set to go.
+
+Misc Notes
+-----------------------------
+
+The current version of the HW does not have an onboard timer, so the 80200
+PMU is not available for general use as it is being used for a timer source.
+
+By default, the MTD driver reserves the first 512K for bootloaders and
+the remaining 3.5MB for the filesystem. You can edit drivers/mtd/map/adi_evb.c
+to change this as needed for your application.
+
+Contributors
+-----------------------------
+
+Thanks to ADI Engineering for providing the hardware for development
+
+Deepak Saxena <dsaxena@mvista.com> - Initial port
+
+-----------------------------
+Enjoy.  If you have any problem please contact Deepak Saxena
+dsaxena@mvista.com
+