Commit aa4a27bc authored by Chen-Yu Tsai's avatar Chen-Yu Tsai Committed by Maxime Ripard

ARM: dts: sun9i: a80-optimus: Add AXP809 PMIC device node and regulators

The AXP809 PMIC is the primary PMIC. It provides various supply voltages
for the SoC and other peripherals. The PMIC's interrupt line is
connected to NMI pin of the SoC.
Signed-off-by: default avatarChen-Yu Tsai <wens@csie.org>
Signed-off-by: default avatarMaxime Ripard <maxime.ripard@free-electrons.com>
parent 51189d64
...@@ -150,7 +150,7 @@ usb3_vbus_pin_optimus: usb3_vbus_pin@1 { ...@@ -150,7 +150,7 @@ usb3_vbus_pin_optimus: usb3_vbus_pin@1 {
&mmc0 { &mmc0 {
pinctrl-names = "default"; pinctrl-names = "default";
pinctrl-0 = <&mmc0_pins>, <&mmc0_cd_pin_optimus>; pinctrl-0 = <&mmc0_pins>, <&mmc0_cd_pin_optimus>;
vmmc-supply = <&reg_vcc3v0>; vmmc-supply = <&reg_dcdc1>;
bus-width = <4>; bus-width = <4>;
cd-gpios = <&pio 7 18 GPIO_ACTIVE_HIGH>; /* PH8 */ cd-gpios = <&pio 7 18 GPIO_ACTIVE_HIGH>; /* PH8 */
cd-inverted; cd-inverted;
...@@ -160,7 +160,7 @@ &mmc0 { ...@@ -160,7 +160,7 @@ &mmc0 {
&mmc2 { &mmc2 {
pinctrl-names = "default"; pinctrl-names = "default";
pinctrl-0 = <&mmc2_8bit_pins>; pinctrl-0 = <&mmc2_8bit_pins>;
vmmc-supply = <&reg_vcc3v0>; vmmc-supply = <&reg_dcdc1>;
bus-width = <8>; bus-width = <8>;
non-removable; non-removable;
cap-mmc-hw-reset; cap-mmc-hw-reset;
...@@ -193,8 +193,135 @@ led_r_pins_optimus: led-pins@1 { ...@@ -193,8 +193,135 @@ led_r_pins_optimus: led-pins@1 {
&r_rsb { &r_rsb {
status = "okay"; status = "okay";
axp809: pmic@3a3 {
reg = <0x3a3>;
interrupt-parent = <&nmi_intc>;
interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
regulators {
reg_aldo1: aldo1 {
/*
* TODO: This should be handled by the
* USB PHY driver.
*/
regulator-always-on;
regulator-min-microvolt = <3000000>;
regulator-max-microvolt = <3000000>;
regulator-name = "vcc33-usbh";
};
reg_aldo2: aldo2 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-name = "vcc-pb-io-cam";
};
aldo3 {
/* unused */
};
reg_dc5ldo: dc5ldo {
regulator-always-on;
regulator-min-microvolt = <800000>;
regulator-max-microvolt = <1100000>;
regulator-name = "vdd-cpus-09-usbh";
};
reg_dcdc1: dcdc1 {
regulator-always-on;
regulator-min-microvolt = <3000000>;
regulator-max-microvolt = <3000000>;
regulator-name = "vcc-3v";
};
reg_dcdc2: dcdc2 {
regulator-min-microvolt = <800000>;
regulator-max-microvolt = <1100000>;
regulator-name = "vdd-gpu";
};
reg_dcdc3: dcdc3 {
regulator-always-on;
regulator-min-microvolt = <800000>;
regulator-max-microvolt = <1100000>;
regulator-name = "vdd-cpua";
};
reg_dcdc4: dcdc4 {
regulator-always-on;
regulator-min-microvolt = <800000>;
regulator-max-microvolt = <1100000>;
regulator-name = "vdd-sys-usb0-hdmi";
};
reg_dcdc5: dcdc5 {
regulator-always-on;
regulator-min-microvolt = <1425000>;
regulator-max-microvolt = <1575000>;
regulator-name = "vcc-dram";
};
reg_dldo1: dldo1 {
/*
* The WiFi chip supports a wide range
* (3.0 ~ 4.8V) of voltages, and so does
* this regulator (3.0 ~ 4.2V), but
* Allwinner SDK always sets it to 3.3V.
*/
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-name = "vcc-wifi";
};
reg_dldo2: dldo2 {
regulator-always-on;
regulator-min-microvolt = <3000000>;
regulator-max-microvolt = <3000000>;
regulator-name = "vcc-pl";
};
reg_eldo1: eldo1 {
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <1200000>;
regulator-name = "vcc-dvdd-cam";
};
reg_eldo2: eldo2 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-name = "vcc-pe";
};
reg_eldo3: eldo3 {
regulator-always-on;
regulator-min-microvolt = <3000000>;
regulator-max-microvolt = <3000000>;
regulator-name = "vcc-pm-codec-io1";
};
reg_ldo_io0: ldo_io0 {
regulator-always-on;
regulator-min-microvolt = <3000000>;
regulator-max-microvolt = <3000000>;
regulator-name = "vcc-pg";
};
reg_ldo_io1: ldo_io1 {
regulator-min-microvolt = <2500000>;
regulator-max-microvolt = <2500000>;
regulator-name = "vcc-pa-gmac-2v5";
};
reg_rtc_ldo: rtc_ldo {
regulator-name = "vcc-rtc-vdd1v8-io";
};
};
};
}; };
#include "axp809.dtsi"
&uart0 { &uart0 {
pinctrl-names = "default"; pinctrl-names = "default";
pinctrl-0 = <&uart0_pins_a>; pinctrl-0 = <&uart0_pins_a>;
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment