ARM: dts: UX500: name the GPIO lines on HREFv60plus

Using the new line naming mechanism from the GPIO subsystem, name
the GPIO lines on the HREFv60plus board that are connected as
GPIO on this design.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

arch/arm/boot/dts/ste-hrefv60plus.dtsi

@@ -18,6 +18,126 @@ / {
 	compatible = "st-ericsson,hrefv60+", "st-ericsson,u8500";
 
 	soc {
+		/* Name the GPIO muxed rails on the HREF boards */
+		gpio@8012e000 {
+			/* GPIOs 0 - 31 */
+			gpio-line-names =
+				     /* GPIO0,1 used for UART0 BT RX/TX */
+				     "", "",
+				     "UART_WAKE",
+				     "BT_WAKE",
+				     "",
+				     "SDMMC_1V8_3V_SEL",
+				     "FLASH_LED_SYNC (FLASH_CTRL_0)",
+				     "XENON_READY (FLASH_CTRL_1)",
+				     "", "", "", "", "", "", "", "",
+				     "", "", "", "",
+				     "",
+				     "FLASH_LED_EN (FLASH_CTRL_3)",
+				     "", "",
+				     "", "", "", "", "",
+				     /* Used by UART2 (console) */
+				     "", "",
+				     "MAGNETOMETER_INT";
+		};
+
+		gpio@8012e080 {
+			/* GPIOs 32 - 63 */
+			gpio-line-names =
+				     "MAGNETOMETER_DRDY",
+				     "", "", "", "", "", "", "",
+				     "", "", "", "", "", "", "", "",
+				     "", "", "", "", "", "", "", "",
+				     "", "", "", "", "", "", "", "";
+		};
+
+		gpio@8000e000 {
+			/* GPIOs 64 - 95 */
+			gpio-line-names = "XENON_EN2 (FLASH_CTRL_4)",
+				     "DISP1_RST",
+				     "DISP2_RST",
+				     "TOUCH_INT2",
+				     "LCD_VSI0_A",
+				     "LCD_VSI1_A",
+				     /* GPIO 70-77 used for ETM */
+				     "", "", "", "", "", "", "", "",
+				     /* GPIO 78-81 used for YCBCR */
+				     "", "", "", "",
+				     "ACCELEROMETER_INT1_RDY",
+				     "ACCELEROMETER_INT2",
+				     "TOUCH_INT",
+				     "WLAN_ENA",
+				     "", "", "", "", "",
+				     "FORCE_SENSING_INT",
+				     "FORCE_SENSING_RESET",
+				     "", "",
+				     "SDMMC_CD";
+		};
+
+		gpio@8000e080 {
+			/* GPIOs 96 - 127 */
+			gpio-line-names = "",
+				     "FORCE_SENSING_WU",
+				     "", "", "", "", "", "",
+				     "", "", "", "", "", "", "", "",
+				     "", "", "", "", "", "", "", "",
+				     "", "", "", "", "", "", "", "";
+		};
+
+		gpio@8000e100 {
+			/* GPIOs 128 - 159 */
+			gpio-line-names = "", "", "", "", "", "", "", "",
+				     "", "", "",
+				     "DIPRO_INT", /* GPIO139 */
+				     "XSHUTDOWN_SECONDARY_SENSOR",
+				     "XSHUTDOWN_PRIMARY_SENSOR",
+				     "NFC_RST (NFC_CTRL_",
+				     "TOUCH_RST",
+				     "NFC_IRQ (NFC_CTRL_1)",
+				     "HAL_SW",
+				     "TOUCH_RST2",
+				     "", "",
+				     "VAUDIO_HF_EN", /* GPIO149 */
+				     "", "", "", "", "", "", "", "", "", "";
+		};
+
+		gpio@8000e180 {
+			/* GPIOs 160 - 191 */
+			gpio-line-names = "", "", "", "", "", "", "", "",
+				     "",
+				     "SDMMC_EN",
+				     "XENON_CHARGE (FLASH_CONTROL_5)",
+				     "GBF_ENA_RESET",
+				     "", "", "", "",
+				     "", "", "", "", "", "", "", "",
+				     "", "", "", "", "", "", "", "";
+		};
+
+		gpio@8011e000 {
+			/* GPIOs 192 - 223 */
+			gpio-line-names = "HDTV_INTN",
+				     "", "", "",
+				     "HDTV_RSTN",
+				     "", "", "",
+				     "", /* GPIO200 */
+				     "", "", "", "", "", "", "",
+				     /* GPIO208-216 used for WGBF_MC1 */
+				     "", "", "", "", "", "", "", "", "",
+				     "SW_FRONT_PROXIMITY", /* GPIO217 */
+				     "KPD_CTRL_INT", /* Keypad controller */
+				     "", "", "", "", "";
+		};
+
+		gpio@8011e080 {
+			/* GPIOs 224 - 255 */
+			gpio-line-names = "", "",
+				     "HSIT_ACWAKE0",
+				     "", "", "", "", "",
+				     "", "", "", "", "", "", "", "",
+				     "", "", "", "", "", "", "", "",
+				     "", "", "", "", "", "", "", "";
+		};
+
 		// External Micro SD slot
 		sdi0_per1@80126000 {
 			cd-gpios  = <&gpio2 31 GPIO_ACTIVE_HIGH>; // 95