Merge branch 'for-linus' of git://git.o-hand.com/linux-mfd

* 'for-linus' of git://git.o-hand.com/linux-mfd:
  mfd: let asic3 use mem resource instead of bus_shift
  mfd: remove DS1WM register definitions from asic3.h
  mfd: add ASIC3_CONFIG_GPIO templates
  mfd: fix the asic3 irq demux code
  mfd: asic3 should depend on gpiolib
  mfd: fix asic3 config array initialisation
  mfd: move asic3 probe functions into __init section
  mfd: Use uppercase only for asic3 macros and defines
  mfd: use dev_* macros for asic3 debugging
  mfd: New asic3 gpio configuration code
  mfd: asic3 children platform data removal
  mfd: asic3 gpiolib support

drivers/mfd/Kconfig

@@ -17,7 +17,7 @@ config MFD_SM501
 
 config MFD_ASIC3
 	bool "Support for Compaq ASIC3"
-	depends on GENERIC_HARDIRQS && ARM
+	depends on GENERIC_HARDIRQS && HAVE_GPIO_LIB && ARM
 	 ---help---
 	  This driver supports the ASIC3 multifunction chip found on many
 	  PDAs (mainly iPAQ and HTC based ones)

include/linux/mfd/asic3.h

@@ -8,7 +8,7 @@
  * published by the Free Software Foundation.
  *
  * Copyright 2001 Compaq Computer Corporation.
- * Copyright 2007 OpendHand.
+ * Copyright 2007-2008 OpenedHand Ltd.
  */
 
 #ifndef __ASIC3_H__
@@ -16,43 +16,22 @@
 
 #include <linux/types.h>
 
-struct asic3 {
-	void __iomem *mapping;
-	unsigned int bus_shift;
-	unsigned int irq_nr;
-	unsigned int irq_base;
-	spinlock_t lock;
-	u16 irq_bothedge[4];
-	struct device *dev;
-};
-
 struct asic3_platform_data {
-	struct {
-		u32 dir;
-		u32 init;
-		u32 sleep_mask;
-		u32 sleep_out;
-		u32 batt_fault_out;
-		u32 sleep_conf;
-		u32 alt_function;
-	} gpio_a, gpio_b, gpio_c, gpio_d;
-
-	unsigned int bus_shift;
+	u16 *gpio_config;
+	unsigned int gpio_config_num;
 
 	unsigned int irq_base;
 
-	struct platform_device **children;
-	unsigned int n_children;
+	unsigned int gpio_base;
 };
 
-int asic3_gpio_get_value(struct asic3 *asic, unsigned gpio);
-void asic3_gpio_set_value(struct asic3 *asic, unsigned gpio, int val);
-
 #define ASIC3_NUM_GPIO_BANKS	4
 #define ASIC3_GPIOS_PER_BANK	16
 #define ASIC3_NUM_GPIOS		64
 #define ASIC3_NR_IRQS		ASIC3_NUM_GPIOS + 6
 
+#define ASIC3_TO_GPIO(gpio) (NR_BUILTIN_GPIO + (gpio))
+
 #define ASIC3_GPIO_BANK_A	0
 #define ASIC3_GPIO_BANK_B	1
 #define ASIC3_GPIO_BANK_C	2
@@ -64,32 +43,89 @@ void asic3_gpio_set_value(struct asic3 *asic, unsigned gpio, int val);
 /* All offsets below are specified with this address bus shift */
 #define ASIC3_DEFAULT_ADDR_SHIFT 2
 
-#define ASIC3_OFFSET(base, reg) (ASIC3_##base##_Base + ASIC3_##base##_##reg)
+#define ASIC3_OFFSET(base, reg) (ASIC3_##base##_BASE + ASIC3_##base##_##reg)
 #define ASIC3_GPIO_OFFSET(base, reg) \
-	(ASIC3_GPIO_##base##_Base + ASIC3_GPIO_##reg)
-
-#define ASIC3_GPIO_A_Base      0x0000
-#define ASIC3_GPIO_B_Base      0x0100
-#define ASIC3_GPIO_C_Base      0x0200
-#define ASIC3_GPIO_D_Base      0x0300
-
-#define ASIC3_GPIO_Mask          0x00    /* R/W 0:don't mask */
-#define ASIC3_GPIO_Direction     0x04    /* R/W 0:input */
-#define ASIC3_GPIO_Out           0x08    /* R/W 0:output low */
-#define ASIC3_GPIO_TriggerType   0x0c    /* R/W 0:level */
-#define ASIC3_GPIO_EdgeTrigger   0x10    /* R/W 0:falling */
-#define ASIC3_GPIO_LevelTrigger  0x14    /* R/W 0:low level detect */
-#define ASIC3_GPIO_SleepMask     0x18    /* R/W 0:don't mask in sleep mode */
-#define ASIC3_GPIO_SleepOut      0x1c    /* R/W level 0:low in sleep mode */
-#define ASIC3_GPIO_BattFaultOut  0x20    /* R/W level 0:low in batt_fault */
-#define ASIC3_GPIO_IntStatus     0x24    /* R/W 0:none, 1:detect */
-#define ASIC3_GPIO_AltFunction   0x28	 /* R/W 1:LED register control */
-#define ASIC3_GPIO_SleepConf     0x2c    /*
+	(ASIC3_GPIO_##base##_BASE + ASIC3_GPIO_##reg)
+
+#define ASIC3_GPIO_A_BASE      0x0000
+#define ASIC3_GPIO_B_BASE      0x0100
+#define ASIC3_GPIO_C_BASE      0x0200
+#define ASIC3_GPIO_D_BASE      0x0300
+
+#define ASIC3_GPIO_TO_BANK(gpio) ((gpio) >> 4)
+#define ASIC3_GPIO_TO_BIT(gpio)  ((gpio) - \
+				  (ASIC3_GPIOS_PER_BANK * ((gpio) >> 4)))
+#define ASIC3_GPIO_TO_MASK(gpio) (1 << ASIC3_GPIO_TO_BIT(gpio))
+#define ASIC3_GPIO_TO_BASE(gpio) (ASIC3_GPIO_A_BASE + (((gpio) >> 4) * 0x0100))
+#define ASIC3_BANK_TO_BASE(bank) (ASIC3_GPIO_A_BASE + ((bank) * 0x100))
+
+#define ASIC3_GPIO_MASK          0x00    /* R/W 0:don't mask */
+#define ASIC3_GPIO_DIRECTION     0x04    /* R/W 0:input */
+#define ASIC3_GPIO_OUT           0x08    /* R/W 0:output low */
+#define ASIC3_GPIO_TRIGGER_TYPE  0x0c    /* R/W 0:level */
+#define ASIC3_GPIO_EDGE_TRIGGER  0x10    /* R/W 0:falling */
+#define ASIC3_GPIO_LEVEL_TRIGGER 0x14    /* R/W 0:low level detect */
+#define ASIC3_GPIO_SLEEP_MASK    0x18    /* R/W 0:don't mask in sleep mode */
+#define ASIC3_GPIO_SLEEP_OUT     0x1c    /* R/W level 0:low in sleep mode */
+#define ASIC3_GPIO_BAT_FAULT_OUT 0x20    /* R/W level 0:low in batt_fault */
+#define ASIC3_GPIO_INT_STATUS    0x24    /* R/W 0:none, 1:detect */
+#define ASIC3_GPIO_ALT_FUNCTION  0x28	 /* R/W 1:LED register control */
+#define ASIC3_GPIO_SLEEP_CONF    0x2c    /*
 					  * R/W bit 1: autosleep
 					  * 0: disable gposlpout in normal mode,
 					  * enable gposlpout in sleep mode.
 					  */
-#define ASIC3_GPIO_Status        0x30    /* R   Pin status */
+#define ASIC3_GPIO_STATUS        0x30    /* R   Pin status */
+
+/*
+ * ASIC3 GPIO config
+ *
+ * Bits 0..6   gpio number
+ * Bits 7..13  Alternate function
+ * Bit  14     Direction
+ * Bit  15     Initial value
+ *
+ */
+#define ASIC3_CONFIG_GPIO_PIN(config) ((config) & 0x7f)
+#define ASIC3_CONFIG_GPIO_ALT(config)  (((config) & (0x7f << 7)) >> 7)
+#define ASIC3_CONFIG_GPIO_DIR(config)  ((config & (1 << 14)) >> 14)
+#define ASIC3_CONFIG_GPIO_INIT(config) ((config & (1 << 15)) >> 15)
+#define ASIC3_CONFIG_GPIO(gpio, alt, dir, init) (((gpio) & 0x7f) \
+	| (((alt) & 0x7f) << 7) | (((dir) & 0x1) << 14) \
+	| (((init) & 0x1) << 15))
+#define ASIC3_CONFIG_GPIO_DEFAULT(gpio, dir, init) \
+	ASIC3_CONFIG_GPIO((gpio), 0, (dir), (init))
+#define ASIC3_CONFIG_GPIO_DEFAULT_OUT(gpio, init) \
+	ASIC3_CONFIG_GPIO((gpio), 0, 1, (init))
+
+/*
+ * Alternate functions
+ */
+#define ASIC3_GPIOA11_PWM0		ASIC3_CONFIG_GPIO(11, 1, 1, 0)
+#define ASIC3_GPIOA12_PWM1		ASIC3_CONFIG_GPIO(12, 1, 1, 0)
+#define ASIC3_GPIOA15_CONTROL_CX	ASIC3_CONFIG_GPIO(15, 1, 1, 0)
+#define ASIC3_GPIOC0_LED0		ASIC3_CONFIG_GPIO(32, 1, 1, 0)
+#define ASIC3_GPIOC1_LED1		ASIC3_CONFIG_GPIO(33, 1, 1, 0)
+#define ASIC3_GPIOC2_LED2		ASIC3_CONFIG_GPIO(34, 1, 1, 0)
+#define ASIC3_GPIOC3_SPI_RXD		ASIC3_CONFIG_GPIO(35, 1, 0, 0)
+#define ASIC3_GPIOC4_CF_nCD		ASIC3_CONFIG_GPIO(36, 1, 0, 0)
+#define ASIC3_GPIOC4_SPI_TXD		ASIC3_CONFIG_GPIO(36, 1, 1, 0)
+#define ASIC3_GPIOC5_SPI_CLK		ASIC3_CONFIG_GPIO(37, 1, 1, 0)
+#define ASIC3_GPIOC5_nCIOW		ASIC3_CONFIG_GPIO(37, 1, 1, 0)
+#define ASIC3_GPIOC6_nCIOR		ASIC3_CONFIG_GPIO(38, 1, 1, 0)
+#define ASIC3_GPIOC7_nPCE_1		ASIC3_CONFIG_GPIO(39, 1, 0, 0)
+#define ASIC3_GPIOC8_nPCE_2		ASIC3_CONFIG_GPIO(40, 1, 0, 0)
+#define ASIC3_GPIOC9_nPOE		ASIC3_CONFIG_GPIO(41, 1, 0, 0)
+#define ASIC3_GPIOC10_nPWE		ASIC3_CONFIG_GPIO(42, 1, 0, 0)
+#define ASIC3_GPIOC11_PSKTSEL		ASIC3_CONFIG_GPIO(43, 1, 0, 0)
+#define ASIC3_GPIOC12_nPREG		ASIC3_CONFIG_GPIO(44, 1, 0, 0)
+#define ASIC3_GPIOC13_nPWAIT		ASIC3_CONFIG_GPIO(45, 1, 1, 0)
+#define ASIC3_GPIOC14_nPIOIS16		ASIC3_CONFIG_GPIO(46, 1, 1, 0)
+#define ASIC3_GPIOC15_nPIOR		ASIC3_CONFIG_GPIO(47, 1, 0, 0)
+#define ASIC3_GPIOD11_nCIOIS16		ASIC3_CONFIG_GPIO(59, 1, 0, 0)
+#define ASIC3_GPIOD12_nCWAIT		ASIC3_CONFIG_GPIO(60, 1, 0, 0)
+#define ASIC3_GPIOD15_nPIOW		ASIC3_CONFIG_GPIO(63, 1, 0, 0)
+
 
 #define ASIC3_SPI_Base		      0x0400
 #define ASIC3_SPI_Control               0x0000
@@ -128,7 +164,7 @@ void asic3_gpio_set_value(struct asic3 *asic, unsigned gpio, int val);
 #define LED_AUTOSTOP	(1 << 5) /* LED ON/OFF auto stop 0:disable, 1:enable */
 #define LED_ALWAYS	(1 << 6) /* LED Interrupt Mask 0:No mask, 1:mask */
 
-#define ASIC3_CLOCK_Base		0x0A00
+#define ASIC3_CLOCK_BASE	   0x0A00
 #define ASIC3_CLOCK_CDEX           0x00
 #define ASIC3_CLOCK_SEL            0x04
 
@@ -159,12 +195,12 @@ void asic3_gpio_set_value(struct asic3 *asic, unsigned gpio, int val);
 #define CLOCK_SEL_CX            (1 << 2)
 
 
-#define ASIC3_INTR_Base		0x0B00
+#define ASIC3_INTR_BASE		0x0B00
 
-#define ASIC3_INTR_IntMask       0x00  /* Interrupt mask control */
-#define ASIC3_INTR_PIntStat      0x04  /* Peripheral interrupt status */
-#define ASIC3_INTR_IntCPS        0x08  /* Interrupt timer clock pre-scale */
-#define ASIC3_INTR_IntTBS        0x0c  /* Interrupt timer set */
+#define ASIC3_INTR_INT_MASK       0x00  /* Interrupt mask control */
+#define ASIC3_INTR_P_INT_STAT     0x04  /* Peripheral interrupt status */
+#define ASIC3_INTR_INT_CPS        0x08  /* Interrupt timer clock pre-scale */
+#define ASIC3_INTR_INT_TBS        0x0c  /* Interrupt timer set */
 
 #define ASIC3_INTMASK_GINTMASK    (1 << 0)  /* Global INTs mask 1:enable */
 #define ASIC3_INTMASK_GINTEL      (1 << 1)  /* 1: rising edge, 0: hi level */
@@ -227,44 +263,12 @@ void asic3_gpio_set_value(struct asic3 *asic, unsigned gpio, int val);
 #define ASIC3_EXTCF_CF_SLEEP             (1 << 15) /* CF sleep mode control */
 
 /*********************************************
- *  The Onewire interface registers
- *
- *  OWM_CMD
- *  OWM_DAT
- *  OWM_INTR
- *  OWM_INTEN
- *  OWM_CLKDIV
+ *  The Onewire interface (DS1WM) is handled
+ *  by the ds1wm driver.
  *
  *********************************************/
 
-#define ASIC3_OWM_Base		0xC00
-
-#define ASIC3_OWM_CMD         0x00
-#define ASIC3_OWM_DAT         0x04
-#define ASIC3_OWM_INTR        0x08
-#define ASIC3_OWM_INTEN       0x0C
-#define ASIC3_OWM_CLKDIV      0x10
-
-#define ASIC3_OWM_CMD_ONEWR         (1 << 0)
-#define ASIC3_OWM_CMD_SRA           (1 << 1)
-#define ASIC3_OWM_CMD_DQO           (1 << 2)
-#define ASIC3_OWM_CMD_DQI           (1 << 3)
-
-#define ASIC3_OWM_INTR_PD          (1 << 0)
-#define ASIC3_OWM_INTR_PDR         (1 << 1)
-#define ASIC3_OWM_INTR_TBE         (1 << 2)
-#define ASIC3_OWM_INTR_TEMP        (1 << 3)
-#define ASIC3_OWM_INTR_RBF         (1 << 4)
-
-#define ASIC3_OWM_INTEN_EPD        (1 << 0)
-#define ASIC3_OWM_INTEN_IAS        (1 << 1)
-#define ASIC3_OWM_INTEN_ETBE       (1 << 2)
-#define ASIC3_OWM_INTEN_ETMT       (1 << 3)
-#define ASIC3_OWM_INTEN_ERBF       (1 << 4)
-
-#define ASIC3_OWM_CLKDIV_PRE       (3 << 0) /* two bits wide at bit 0 */
-#define ASIC3_OWM_CLKDIV_DIV       (7 << 2) /* 3 bits wide at bit 2 */
-
+#define ASIC3_OWM_BASE		0xC00
 
 /*****************************************************************************
  *  The SD configuration registers are at a completely different location
@@ -492,6 +496,7 @@ void asic3_gpio_set_value(struct asic3 *asic, unsigned gpio, int val);
 #define ASIC3_SDIO_CTRL_LEDCtrl              0x7C
 #define ASIC3_SDIO_CTRL_SoftwareReset        0x1C0
 
-#define ASIC3_MAP_SIZE	     		     0x2000
+#define ASIC3_MAP_SIZE_32BIT	0x2000
+#define ASIC3_MAP_SIZE_16BIT	0x1000
 
 #endif /* __ASIC3_H__ */