Commit ae740dbc authored by Vojtech Pavlik's avatar Vojtech Pavlik

Merge suse.cz:/home/vojtech/bk/linus into suse.cz:/home/vojtech/bk/input

parents b02a51da 8d9a1053
......@@ -434,7 +434,7 @@ Here are described their command lines:
Using gamecon.c you can connect up to five devices to one parallel port. It
uses the following kernel/module command line:
gc=port,pad1,pad2,pad3,pad4,pad5
gamecon.map=port,pad1,pad2,pad3,pad4,pad5
Where 'port' the number of the parport interface (eg. 0 for parport0).
......@@ -457,15 +457,15 @@ uses the following kernel/module command line:
your controller plugged in before initializing.
Should you want to use more than one of parallel ports at once, you can use
gc_2 and gc_3 as additional command line parameters for two more parallel
ports.
gamecon.map2 and gamecon.map3 as additional command line parameters for two
more parallel ports.
3.2 db9.c
~~~~~~~~~
Apart from making an interface, there is nothing difficult on using the
db9.c driver. It uses the following kernel/module command line:
db9=port,type
db9.dev=port,type
Where 'port' is the number of the parport interface (eg. 0 for parport0).
......@@ -489,14 +489,14 @@ Old parallel ports may not have this feature.
10 | Amiga CD32 pad
Should you want to use more than one of these joysticks/pads at once, you
can use db9_2 and db9_3 as additional command line parameters for two
can use db9.dev2 and db9.dev3 as additional command line parameters for two
more joysticks/pads.
3.3 turbografx.c
~~~~~~~~~~~~~~~~
The turbografx.c driver uses a very simple kernel/module command line:
tgfx=port,js1,js2,js3,js4,js5,js6,js7
turbografx.map=port,js1,js2,js3,js4,js5,js6,js7
Where 'port' is the number of the parport interface (eg. 0 for parport0).
......@@ -504,8 +504,8 @@ more joysticks/pads.
interface ports 1-7 have. For a standard multisystem joystick, this is 1.
Should you want to use more than one of these interfaces at once, you can
use tgfx_2 and tgfx_3 as additional command line parameters for two more
interfaces.
use turbografx.map2 and turbografx.map3 as additional command line parameters
for two more interfaces.
3.4 PC parallel port pinout
~~~~~~~~~~~~~~~~~~~~~~~~~~~
......
......@@ -111,7 +111,7 @@ your needs:
alias tty-ldisc-2 serport
alias char-major-13 input
above input joydev ns558 analog
options analog js=gamepad
options analog map=gamepad,none,2btn
2.5 Verifying that it works
~~~~~~~~~~~~~~~~~~~~~~~~~~~
......@@ -185,7 +185,7 @@ you'll need to specify the types either on the kernel command line or on the
module command line, when inserting analog.o into the kernel. The
parameters are:
js=type,type,type,....
analog.map=<type1>,<type2>,<type3>,....
'type' is type of the joystick from the table below, defining joysticks
present on gameports in the system, starting with gameport0, second 'type'
......@@ -419,7 +419,7 @@ card.
Amiga joysticks, connected to an Amiga, are supported by the amijoy.c
driver. Since they can't be autodetected, the driver has a command line.
amijoy=a,b
amijoy.map=<a>,<b>
a and b define the joysticks connected to the JOY0DAT and JOY1DAT ports of
the Amiga.
......
......@@ -151,7 +151,15 @@ running once the system is up.
Format: <host-scsi-id>,<target-scsi-id>,<max-rate>,<max-offset>
See also header of drivers/scsi/AM53C974.c.
amijoy= [HW,JOY] Amiga joystick support
amijoy.map= [HW,JOY] Amiga joystick support
Map of devices attached to JOY0DAT and JOY1DAT
Format: <a>,<b>
See also Documentation/kernel/input/joystick.txt
analog.map= [HW,JOY] Analog joystick and gamepad support
Specifies type or capabilities of an analog joystick
connected to one of 16 gameports
Format: <type1>,<type2>,..<type16>
apc= [HW,SPARC] Power management functions (SPARCstation-4/5 + deriv.)
Format: noidle
......@@ -174,11 +182,18 @@ running once the system is up.
atascsi= [HW,SCSI] Atari SCSI
atkbd.set= [HW] Select keyboard code set
Format: <int>
atkbd.extra= [HW] Enable extra LEDs and keys on IBM RapidAccess, EzKey
and similar keyboards
atkbd.reset= [HW] Reset keyboard during initialization
atkbd.set= [HW] Select keyboard code set
Format: <int> (2 = AT (default) 3 = PS/2)
atkbd.scroll= [HW] Enable scroll wheel on MS Office and similar keyboards
atkbd.softrepeat=
[HW] Use software keyboard repeat
atkbd.reset= [HW] Reset keyboard during initialization
autotest [IA64]
......@@ -280,10 +295,11 @@ running once the system is up.
dasd= [HW,NET]
See header of drivers/s390/block/dasd_devmap.c.
db9= [HW,JOY]
db9_2=
db9_3=
db9.dev[2|3]= [HW,JOY] Multisystem joystick support via parallel port
(one device per port)
Format: <port#>,<type>
See also Documentation/input/joystick-parport.txt
debug [KNL] Enable kernel debugging (events log level).
decnet= [HW,NET]
......@@ -377,12 +393,14 @@ running once the system is up.
ftape= [HW] Floppy Tape subsystem debugging options.
See Documentation/ftape.txt.
gamecon.map[2|3]=
[HW,JOY] Multisystem joystick and NES/SNES/PSX pad
support via parallel port (up to 5 devices per port)
Format: <port#>,<pad1>,<pad2>,<pad3>,<pad4>,<pad5>
See also Documentation/input/joystick-parport.txt
gamma= [HW,DRM]
gc= [HW,JOY]
gc_2= See Documentation/input/joystick-parport.txt.
gc_3=
gdth= [HW,SCSI]
See header of drivers/scsi/gdth.c.
......@@ -609,9 +627,9 @@ running once the system is up.
mga= [HW,DRM]
mousedev.xres [MOUSE] Horizontal screen resolution, used for devices
mousedev.xres= [MOUSE] Horizontal screen resolution, used for devices
reporting absolute coordinates, such as tablets
mousedev.yres [MOUSE] Vertical screen resolution, used for devices
mousedev.yres= [MOUSE] Vertical screen resolution, used for devices
reporting absolute coordinates, such as tablets
mpu401= [HW,OSS]
......@@ -1156,10 +1174,6 @@ running once the system is up.
See header of drivers/scsi/t128.c.
tdfx= [HW,DRM]
tgfx= [HW,JOY] TurboGraFX parallel port interface
tgfx_2= See Documentation/input/joystick-parport.txt.
tgfx_3=
thash_entries= [KNL,NET]
Set number of hash buckets for TCP connection
......@@ -1182,8 +1196,13 @@ running once the system is up.
trix= [HW,OSS] MediaTrix AudioTrix Pro
Format: <io>,<irq>,<dma>,<dma2>,<sb_io>,<sb_irq>,<sb_dma>,<mpu_io>,<mpu_irq>
tsdev.xres [TS] Horizontal screen resolution.
tsdev.yres [TS] Vertical screen resolution.
tsdev.xres= [TS] Horizontal screen resolution.
tsdev.yres= [TS] Vertical screen resolution.
turbografx.map[2|3]=
[HW,JOY] TurboGraFX parallel port interface
Format: <port#>,<js1>,<js2>,<js3>,<js4>,<js5>,<js6>,<js7>
See also Documentation/input/joystick-parport.txt
u14-34f= [HW,SCSI] UltraStor 14F/34F SCSI host adapter
See header of drivers/scsi/u14-34f.c.
......
......@@ -28,7 +28,7 @@ in the package: See the file COPYING.
1. Usage
~~~~~~~~
The drivers/usb/acm.c drivers works with USB modems and USB ISDN terminal
The drivers/usb/class/cdc-acm.c drivers works with USB modems and USB ISDN terminal
adapters that conform to the Universal Serial Bus Communication Device Class
Abstract Control Model (USB CDC ACM) specification.
......@@ -65,9 +65,9 @@ minor/major numbers anywhere you want, but either the above location or
To use the modems you need these modules loaded:
usbcore.o
usb-[uo]hci.o or uhci.o
acm.o
usbcore.ko
uhci-hcd.ko ohci-hcd.ko or ehci-hcd.ko
cdc-acm.ko
After that, the modem[s] should be accessible. You should be able to use
minicom, ppp and mgetty with them.
......
......@@ -198,11 +198,6 @@ source "drivers/input/Kconfig"
source "drivers/char/Kconfig"
config KBDMOUSE
bool
depends on ARCH_ACORN && BUSMOUSE=y
default y
source "drivers/media/Kconfig"
source "fs/Kconfig"
......
......@@ -599,30 +599,6 @@ config PC9800_OLDLP_CONSOLE
bool "Support for console on line printer"
depends on PC9800_OLDLP
menu "Mice"
config BUSMOUSE
tristate "Bus Mouse Support"
---help---
Say Y here if your machine has a bus mouse as opposed to a serial
mouse. Most people have a regular serial MouseSystem or
Microsoft mouse (made by Logitech) that plugs into a COM port
(rectangular with 9 or 25 pins). These people say N here.
If you have a laptop, you either have to check the documentation or
experiment a bit to find out whether the trackball is a serial mouse
or not; it's best to say Y here for you.
This is the generic bus mouse driver code. If you have a bus mouse,
you will have to say Y here and also to the specific driver for your
mouse below.
To compile this driver as a module, choose M here: the
module will be called busmouse.
endmenu
config QIC02_TAPE
tristate "QIC-02 tape support"
help
......
......@@ -49,7 +49,6 @@ obj-$(CONFIG_PRINTER) += lp.o
obj-$(CONFIG_TIPAR) += tipar.o
obj-$(CONFIG_PC9800_OLDLP) += lp_old98.o
obj-$(CONFIG_BUSMOUSE) += busmouse.o
obj-$(CONFIG_DTLK) += dtlk.o
obj-$(CONFIG_R3964) += n_r3964.o
obj-$(CONFIG_APPLICOM) += applicom.o
......
......@@ -209,7 +209,7 @@ static int evdev_ioctl(struct inode *inode, struct file *file, unsigned int cmd,
struct evdev *evdev = list->evdev;
struct input_dev *dev = evdev->handle.dev;
struct input_absinfo abs;
int t, u, v;
int i, t, u, v;
if (!evdev->exist) return -ENODEV;
......@@ -234,6 +234,9 @@ static int evdev_ioctl(struct inode *inode, struct file *file, unsigned int cmd,
u = SET_INPUT_KEYCODE(dev, t, v);
clear_bit(u, dev->keybit);
set_bit(v, dev->keybit);
for (i = 0; i < dev->keycodemax; i++)
if (INPUT_KEYCODE(dev,i) == u)
set_bit(u, dev->keybit);
return 0;
case EVIOCSFF:
......
......@@ -77,7 +77,7 @@ static void ns558_isa_probe(int io)
* No one should be using this address.
*/
if (check_region(io, 1))
if (!request_region(io, 1, "ns558-isa"))
return;
/*
......@@ -89,7 +89,8 @@ static void ns558_isa_probe(int io)
outb(~c & ~3, io);
if (~(u = v = inb(io)) & 3) {
outb(c, io);
return;
i = 0;
goto out;
}
/*
* After a trigger, there must be at least some bits changing.
......@@ -99,7 +100,8 @@ static void ns558_isa_probe(int io)
if (u == v) {
outb(c, io);
return;
i = 0;
goto out;
}
wait_ms(3);
/*
......@@ -110,7 +112,8 @@ static void ns558_isa_probe(int io)
for (i = 0; i < 1000; i++)
if ((u ^ inb(io)) & 0xf) {
outb(c, io);
return;
i = 0;
goto out;
}
/*
* And now find the number of mirrors of the port.
......@@ -118,7 +121,9 @@ static void ns558_isa_probe(int io)
for (i = 1; i < 5; i++) {
if (check_region(io & (-1 << i), (1 << i))) /* Don't disturb anyone */
release_region(io & (-1 << (i-1)), (1 << (i-1)));
if (!request_region(io & (-1 << i), (1 << i), "ns558-isa")) /* Don't disturb anyone */
break;
outb(0xff, io & (-1 << i));
......@@ -126,18 +131,25 @@ static void ns558_isa_probe(int io)
if (inb(io & (-1 << i)) != inb((io & (-1 << i)) + (1 << i) - 1)) b++;
wait_ms(3);
if (b > 300) /* We allow 30% difference */
if (b > 300) { /* We allow 30% difference */
release_region(io & (-1 << i), (1 << i));
break;
}
}
i--;
if (i != 4) {
if (!request_region(io & (-1 << i), (1 << i), "ns558-isa"))
return;
}
if (!(port = kmalloc(sizeof(struct ns558), GFP_KERNEL))) {
printk(KERN_ERR "ns558: Memory allocation failed.\n");
return;
goto out;
}
memset(port, 0, sizeof(struct ns558));
memset(port, 0, sizeof(struct ns558));
port->type = NS558_ISA;
port->size = (1 << i);
port->gameport.io = io;
......@@ -148,8 +160,6 @@ static void ns558_isa_probe(int io)
sprintf(port->phys, "isa%04x/gameport0", io & (-1 << i));
sprintf(port->name, "NS558 ISA");
request_region(io & (-1 << i), (1 << i), "ns558-isa");
gameport_register_port(&port->gameport);
printk(KERN_INFO "gameport: NS558 ISA at %#x", port->gameport.io);
......@@ -157,6 +167,9 @@ static void ns558_isa_probe(int io)
printk(" speed %d kHz\n", port->gameport.speed);
list_add(&port->node, &ns558_list);
return;
out:
release_region(io & (-1 << i), (1 << i));
}
#ifdef CONFIG_PNP
......
......@@ -32,6 +32,7 @@
#include <linux/errno.h>
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/moduleparam.h>
#include <linux/init.h>
#include <linux/input.h>
#include <linux/interrupt.h>
......@@ -42,10 +43,15 @@
MODULE_AUTHOR("Vojtech Pavlik <vojtech@ucw.cz>");
MODULE_DESCRIPTION("Driver for Amiga joysticks");
MODULE_PARM(amijoy, "1-2i");
MODULE_LICENSE("GPL");
static int amijoy[2] = { 0, 1 };
static int amijoy_nargs;
module_param_array_named(map, amijoy, uint, amijoy_nargs, 0);
MODULE_PARM_DESC(map, "Map of attached joysticks in form of <a>,<b> (default is 0,1)");
__obsolete_setup("amijoy=");
static int amijoy_used[2] = { 0, 0 };
static struct input_dev amijoy_dev[2];
static char *amijoy_phys[2] = { "amijoy/input0", "amijoy/input1" };
......@@ -101,17 +107,6 @@ static void amijoy_close(struct input_dev *dev)
free_irq(IRQ_AMIGA_VERTB, amijoy_interrupt);
}
static int __init amijoy_setup(char *str)
{
int i;
int ints[4];
str = get_options(str, ARRAY_SIZE(ints), ints);
for (i = 0; i <= ints[0] && i < 2; i++) amijoy[i] = ints[i+1];
return 1;
}
__setup("amijoy=", amijoy_setup);
static int __init amijoy_init(void)
{
int i, j;
......
......@@ -32,6 +32,7 @@
#include <linux/delay.h>
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/moduleparam.h>
#include <linux/slab.h>
#include <linux/bitops.h>
#include <linux/init.h>
......@@ -50,9 +51,12 @@ MODULE_LICENSE("GPL");
#define ANALOG_PORTS 16
static char *js[ANALOG_PORTS];
static int js_nargs;
static int analog_options[ANALOG_PORTS];
MODULE_PARM(js, "1-" __MODULE_STRING(ANALOG_PORTS) "s");
MODULE_PARM_DESC(js, "Analog joystick options");
module_param_array_named(map, js, charp, js_nargs, 0);
MODULE_PARM_DESC(map, "Describes analog joysticks type/capabilities");
__obsolete_setup("js=");
/*
* Times, feature definitions.
......@@ -711,7 +715,7 @@ static void analog_parse_options(void)
int i, j;
char *end;
for (i = 0; i < ANALOG_PORTS && js[i]; i++) {
for (i = 0; i < js_nargs; i++) {
for (j = 0; analog_types[j].name; j++)
if (!strcmp(analog_types[j].name, js[i])) {
......@@ -742,24 +746,6 @@ static struct gameport_dev analog_dev = {
.disconnect = analog_disconnect,
};
#ifndef MODULE
static int __init analog_setup(char *str)
{
char *s = str;
int i = 0;
if (!str || !*str) return 0;
while ((str = s) && (i < ANALOG_PORTS)) {
if ((s = strchr(str,','))) *s++ = 0;
js[i++] = str;
}
return 1;
}
__setup("js=", analog_setup);
#endif
int __init analog_init(void)
{
analog_parse_options();
......
......@@ -33,6 +33,7 @@
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/moduleparam.h>
#include <linux/delay.h>
#include <linux/init.h>
#include <linux/parport.h>
......@@ -42,9 +43,24 @@ MODULE_AUTHOR("Vojtech Pavlik <vojtech@ucw.cz>");
MODULE_DESCRIPTION("Atari, Amstrad, Commodore, Amiga, Sega, etc. joystick driver");
MODULE_LICENSE("GPL");
MODULE_PARM(db9, "2i");
MODULE_PARM(db9_2, "2i");
MODULE_PARM(db9_3, "2i");
static int db9[] __initdata = { -1, 0 };
static int db9_nargs __initdata = 0;
module_param_array_named(dev, db9, int, db9_nargs, 0);
MODULE_PARM_DESC(dev, "Describes first attached device (<parport#>,<type>)");
static int db9_2[] __initdata = { -1, 0 };
static int db9_nargs_2 __initdata = 0;
module_param_array_named(dev2, db9_2, int, db9_nargs_2, 0);
MODULE_PARM_DESC(dev2, "Describes second attached device (<parport#>,<type>)");
static int db9_3[] __initdata = { -1, 0 };
static int db9_nargs_3 __initdata = 0;
module_param_array_named(dev3, db9_3, int, db9_nargs_3, 0);
MODULE_PARM_DESC(dev3, "Describes third attached device (<parport#>,<type>)");
__obsolete_setup("db9=");
__obsolete_setup("db9_2=");
__obsolete_setup("db9_3=");
#define DB9_MULTI_STICK 0x01
#define DB9_MULTI2_STICK 0x02
......@@ -76,10 +92,6 @@ MODULE_PARM(db9_3, "2i");
#define DB9_GENESIS6_DELAY 14
#define DB9_REFRESH_TIME HZ/100
static int db9[] __initdata = { -1, 0 };
static int db9_2[] __initdata = { -1, 0 };
static int db9_3[] __initdata = { -1, 0 };
struct db9 {
struct input_dev dev[DB9_MAX_DEVICES];
struct timer_list timer;
......@@ -518,7 +530,7 @@ static void db9_close(struct input_dev *dev)
}
}
static struct db9 __init *db9_probe(int *config)
static struct db9 __init *db9_probe(int *config, int nargs)
{
struct db9 *db9;
struct parport *pp;
......@@ -526,6 +538,12 @@ static struct db9 __init *db9_probe(int *config)
if (config[0] < 0)
return NULL;
if (nargs < 2) {
printk(KERN_ERR "db9.c: Device type must be specified.\n");
return NULL;
}
if (config[1] < 1 || config[1] >= DB9_MAX_PAD || !db9_buttons[config[1]]) {
printk(KERN_ERR "db9.c: bad config\n");
return NULL;
......@@ -601,38 +619,11 @@ static struct db9 __init *db9_probe(int *config)
return db9;
}
#ifndef MODULE
static int __init db9_setup(char *str)
{
int i, ints[3];
get_options(str, ARRAY_SIZE(ints), ints);
for (i = 0; i <= ints[0] && i < 2; i++) db9[i] = ints[i + 1];
return 1;
}
static int __init db9_setup_2(char *str)
{
int i, ints[3];
get_options(str, ARRAY_SIZE(ints), ints);
for (i = 0; i <= ints[0] && i < 2; i++) db9_2[i] = ints[i + 1];
return 1;
}
static int __init db9_setup_3(char *str)
{
int i, ints[3];
get_options(str, ARRAY_SIZE(ints), ints);
for (i = 0; i <= ints[0] && i < 2; i++) db9_3[i] = ints[i + 1];
return 1;
}
__setup("db9=", db9_setup);
__setup("db9_2=", db9_setup_2);
__setup("db9_3=", db9_setup_3);
#endif
int __init db9_init(void)
{
db9_base[0] = db9_probe(db9);
db9_base[1] = db9_probe(db9_2);
db9_base[2] = db9_probe(db9_3);
db9_base[0] = db9_probe(db9, db9_nargs);
db9_base[1] = db9_probe(db9_2, db9_nargs_2);
db9_base[2] = db9_probe(db9_3, db9_nargs_3);
if (db9_base[0] || db9_base[1] || db9_base[2])
return 0;
......
......@@ -35,6 +35,7 @@
#include <linux/kernel.h>
#include <linux/delay.h>
#include <linux/module.h>
#include <linux/moduleparam.h>
#include <linux/init.h>
#include <linux/parport.h>
#include <linux/input.h>
......@@ -43,10 +44,26 @@ MODULE_AUTHOR("Vojtech Pavlik <vojtech@ucw.cz>");
MODULE_DESCRIPTION("NES, SNES, N64, MultiSystem, PSX gamepad driver");
MODULE_LICENSE("GPL");
MODULE_PARM(gc, "2-6i");
MODULE_PARM(gc_2,"2-6i");
MODULE_PARM(gc_3,"2-6i");
MODULE_PARM(gc_psx_delay, "i");
static int gc[] __initdata = { -1, 0, 0, 0, 0, 0 };
static int gc_nargs __initdata = 0;
module_param_array_named(map, gc, int, gc_nargs, 0);
MODULE_PARM_DESC(map, "Describers first set of devices (<parport#>,<pad1>,<pad2>,..<pad5>)");
static int gc_2[] __initdata = { -1, 0, 0, 0, 0, 0 };
static int gc_nargs_2 __initdata = 0;
module_param_array_named(map2, gc_2, int, gc_nargs_2, 0);
MODULE_PARM_DESC(map2, "Describers second set of devices");
static int gc_3[] __initdata = { -1, 0, 0, 0, 0, 0 };
static int gc_nargs_3 __initdata = 0;
module_param_array_named(map3, gc_3, int, gc_nargs_3, 0);
MODULE_PARM_DESC(map3, "Describers third set of devices");
__obsolete_setup("gc=");
__obsolete_setup("gc_2=");
__obsolete_setup("gc_3=");
/* see also gs_psx_delay parameter in PSX support section */
#define GC_SNES 1
#define GC_NES 2
......@@ -71,10 +88,6 @@ struct gc {
static struct gc *gc_base[3];
static int gc[] __initdata = { -1, 0, 0, 0, 0, 0 };
static int gc_2[] __initdata = { -1, 0, 0, 0, 0, 0 };
static int gc_3[] __initdata = { -1, 0, 0, 0, 0, 0 };
static int gc_status_bit[] = { 0x40, 0x80, 0x20, 0x10, 0x08 };
static char *gc_names[] = { NULL, "SNES pad", "NES pad", "NES FourPort", "Multisystem joystick",
......@@ -232,6 +245,11 @@ static void gc_multi_read_packet(struct gc *gc, int length, unsigned char *data)
#define GC_PSX_LEN(x) ((x) & 0xf) /* Low nibble is length in words */
static int gc_psx_delay = GC_PSX_DELAY;
module_param_named(psx_delay, gc_psx_delay, uint, 0);
MODULE_PARM_DESC(psx_delay, "Delay when accessing Sony PSX controller (usecs)");
__obsolete_setup("gc_psx_delay=");
static short gc_psx_abs[] = { ABS_X, ABS_Y, ABS_RX, ABS_RY, ABS_HAT0X, ABS_HAT0Y };
static short gc_psx_btn[] = { BTN_TL, BTN_TR, BTN_TL2, BTN_TR2, BTN_A, BTN_B, BTN_X, BTN_Y,
BTN_START, BTN_SELECT, BTN_THUMBL, BTN_THUMBR };
......@@ -468,7 +486,7 @@ static void gc_close(struct input_dev *dev)
}
}
static struct gc __init *gc_probe(int *config)
static struct gc __init *gc_probe(int *config, int nargs)
{
struct gc *gc;
struct parport *pp;
......@@ -478,6 +496,11 @@ static struct gc __init *gc_probe(int *config)
if (config[0] < 0)
return NULL;
if (nargs < 2) {
printk(KERN_ERR "gamecon.c: at least one device must be specified\n");
return NULL;
}
pp = parport_find_number(config[0]);
if (!pp) {
......@@ -507,7 +530,7 @@ static struct gc __init *gc_probe(int *config)
gc->timer.data = (long) gc;
gc->timer.function = gc_timer;
for (i = 0; i < 5; i++) {
for (i = 0; i < nargs - 1; i++) {
if (!config[i + 1])
continue;
......@@ -632,44 +655,11 @@ static struct gc __init *gc_probe(int *config)
return gc;
}
#ifndef MODULE
static int __init gc_setup(char *str)
{
int i, ints[7];
get_options(str, ARRAY_SIZE(ints), ints);
for (i = 0; i <= ints[0] && i < 6; i++) gc[i] = ints[i + 1];
return 1;
}
static int __init gc_setup_2(char *str)
{
int i, ints[7];
get_options(str, ARRAY_SIZE(ints), ints);
for (i = 0; i <= ints[0] && i < 6; i++) gc_2[i] = ints[i + 1];
return 1;
}
static int __init gc_setup_3(char *str)
{
int i, ints[7];
get_options(str, ARRAY_SIZE(ints), ints);
for (i = 0; i <= ints[0] && i < 6; i++) gc_3[i] = ints[i + 1];
return 1;
}
static int __init gc_psx_setup(char *str)
{
get_option(&str, &gc_psx_delay);
return 1;
}
__setup("gc=", gc_setup);
__setup("gc_2=", gc_setup_2);
__setup("gc_3=", gc_setup_3);
__setup("gc_psx_delay=", gc_psx_setup);
#endif
int __init gc_init(void)
{
gc_base[0] = gc_probe(gc);
gc_base[1] = gc_probe(gc_2);
gc_base[2] = gc_probe(gc_3);
gc_base[0] = gc_probe(gc, gc_nargs);
gc_base[1] = gc_probe(gc_2, gc_nargs_2);
gc_base[2] = gc_probe(gc_3, gc_nargs_3);
if (gc_base[0] || gc_base[1] || gc_base[2])
return 0;
......
......@@ -35,15 +35,31 @@
#include <linux/parport.h>
#include <linux/input.h>
#include <linux/module.h>
#include <linux/moduleparam.h>
#include <linux/init.h>
MODULE_AUTHOR("Vojtech Pavlik <vojtech@ucw.cz>");
MODULE_DESCRIPTION("TurboGraFX parallel port interface driver");
MODULE_LICENSE("GPL");
MODULE_PARM(tgfx, "2-8i");
MODULE_PARM(tgfx_2, "2-8i");
MODULE_PARM(tgfx_3, "2-8i");
static int tgfx[] __initdata = { -1, 0, 0, 0, 0, 0, 0, 0 };
static int tgfx_nargs __initdata = 0;
module_param_array_named(map, tgfx, int, tgfx_nargs, 0);
MODULE_PARM_DESC(map, "Describes first set of devices (<parport#>,<js1>,<js2>,..<js7>");
static int tgfx_2[] __initdata = { -1, 0, 0, 0, 0, 0, 0, 0 };
static int tgfx_nargs_2 __initdata = 0;
module_param_array_named(map2, tgfx_2, int, tgfx_nargs_2, 0);
MODULE_PARM_DESC(map2, "Describes second set of devices");
static int tgfx_3[] __initdata = { -1, 0, 0, 0, 0, 0, 0, 0 };
static int tgfx_nargs_3 __initdata = 0;
module_param_array_named(map3, tgfx_3, int, tgfx_nargs_3, 0);
MODULE_PARM_DESC(map3, "Describes third set of devices");
__obsolete_setup("tgfx=");
__obsolete_setup("tgfx_2=");
__obsolete_setup("tgfx_3=");
#define TGFX_REFRESH_TIME HZ/100 /* 10 ms */
......@@ -58,10 +74,6 @@ MODULE_PARM(tgfx_3, "2-8i");
#define TGFX_TOP 0x01
#define TGFX_TOP2 0x08
static int tgfx[] __initdata = { -1, 0, 0, 0, 0, 0, 0, 0 };
static int tgfx_2[] __initdata = { -1, 0, 0, 0, 0, 0, 0, 0 };
static int tgfx_3[] __initdata = { -1, 0, 0, 0, 0, 0, 0, 0 };
static int tgfx_buttons[] = { BTN_TRIGGER, BTN_THUMB, BTN_THUMB2, BTN_TOP, BTN_TOP2 };
static char *tgfx_name = "TurboGraFX Multisystem joystick";
......@@ -133,7 +145,7 @@ static void tgfx_close(struct input_dev *dev)
* tgfx_probe() probes for tg gamepads.
*/
static struct tgfx __init *tgfx_probe(int *config)
static struct tgfx __init *tgfx_probe(int *config, int nargs)
{
struct tgfx *tgfx;
struct parport *pp;
......@@ -142,6 +154,11 @@ static struct tgfx __init *tgfx_probe(int *config)
if (config[0] < 0)
return NULL;
if (nargs < 2) {
printk(KERN_ERR "turbografx.c: at least one joystick must be specified\n");
return NULL;
}
pp = parport_find_number(config[0]);
if (!pp) {
......@@ -171,7 +188,7 @@ static struct tgfx __init *tgfx_probe(int *config)
tgfx->sticks = 0;
for (i = 0; i < 7; i++)
for (i = 0; i < nargs - 1; i++)
if (config[i+1] > 0 && config[i+1] < 6) {
tgfx->sticks |= (1 << i);
......@@ -212,38 +229,11 @@ static struct tgfx __init *tgfx_probe(int *config)
return tgfx;
}
#ifndef MODULE
static int __init tgfx_setup(char *str)
{
int i, ints[9];
get_options(str, ARRAY_SIZE(ints), ints);
for (i = 0; i <= ints[0] && i < 8; i++) tgfx[i] = ints[i + 1];
return 1;
}
static int __init tgfx_setup_2(char *str)
{
int i, ints[9];
get_options(str, ARRAY_SIZE(ints), ints);
for (i = 0; i <= ints[0] && i < 8; i++) tgfx_2[i] = ints[i + 1];
return 1;
}
static int __init tgfx_setup_3(char *str)
{
int i, ints[9];
get_options(str, ARRAY_SIZE(ints), ints);
for (i = 0; i <= ints[0] && i < 8; i++) tgfx_3[i] = ints[i + 1];
return 1;
}
__setup("tgfx=", tgfx_setup);
__setup("tgfx_2=", tgfx_setup_2);
__setup("tgfx_3=", tgfx_setup_3);
#endif
int __init tgfx_init(void)
{
tgfx_base[0] = tgfx_probe(tgfx);
tgfx_base[1] = tgfx_probe(tgfx_2);
tgfx_base[2] = tgfx_probe(tgfx_3);
tgfx_base[0] = tgfx_probe(tgfx, tgfx_nargs);
tgfx_base[1] = tgfx_probe(tgfx_2, tgfx_nargs_2);
tgfx_base[2] = tgfx_probe(tgfx_3, tgfx_nargs_3);
if (tgfx_base[0] || tgfx_base[1] || tgfx_base[2])
return 0;
......
......@@ -17,6 +17,7 @@ config KEYBOARD_ATKBD
depends on INPUT && INPUT_KEYBOARD
select SERIO
select SERIO_I8042 if PC
select SERIO_GSCPS2 if GSC
help
Say Y here if you want to use a standard AT or PS/2 keyboard. Usually
you'll need this, unless you have a different type keyboard (USB, ADB
......@@ -40,6 +41,19 @@ config KEYBOARD_SUNKBD
To compile this driver as a module, choose M here: the
module will be called sunkbd.
config KEYBOARD_LKKBD
tristate "DECstation/VAXstation LK201/LK401 keyboard support"
depends on INPUT && INPUT_KEYBOARD
select SERIO
help
Say Y here if you want to use a LK201 or LK401 style serial
keyboard. This keyboard is also useable on PCs if you attach
it with the inputattach program. The connector pinout is
described within lkkbd.c.
To compile this driver as a module, choose M here: the
module will be called lkkbd.
config KEYBOARD_XTKBD
tristate "XT Keyboard support"
depends on INPUT && INPUT_KEYBOARD
......
......@@ -7,6 +7,7 @@
obj-$(CONFIG_KEYBOARD_ATKBD) += atkbd.o
obj-$(CONFIG_KEYBOARD_MAPLE) += maple_keyb.o
obj-$(CONFIG_KEYBOARD_SUNKBD) += sunkbd.o
obj-$(CONFIG_KEYBOARD_LKKBD) += lkkbd.o
obj-$(CONFIG_KEYBOARD_XTKBD) += xtkbd.o
obj-$(CONFIG_KEYBOARD_AMIGA) += amikbd.o
obj-$(CONFIG_KEYBOARD_NEWTON) += newtonkbd.o
......
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
......@@ -77,6 +77,7 @@ struct sunkbd {
struct input_dev dev;
struct serio *serio;
struct work_struct tq;
wait_queue_head_t wait;
char name[64];
char phys[32];
char type;
......@@ -96,11 +97,13 @@ static irqreturn_t sunkbd_interrupt(struct serio *serio,
if (sunkbd->reset <= -1) { /* If cp[i] is 0xff, sunkbd->reset will stay -1. */
sunkbd->reset = data; /* The keyboard sends 0xff 0xff 0xID on powerup */
wake_up_interruptible(&sunkbd->wait);
goto out;
}
if (sunkbd->layout == -1) {
sunkbd->layout = data;
wake_up_interruptible(&sunkbd->wait);
goto out;
}
......@@ -176,22 +179,19 @@ static int sunkbd_event(struct input_dev *dev, unsigned int type, unsigned int c
static int sunkbd_initialize(struct sunkbd *sunkbd)
{
int t;
t = 1000;
sunkbd->reset = -2;
sunkbd->serio->write(sunkbd->serio, SUNKBD_CMD_RESET);
while (sunkbd->reset < 0 && --t) mdelay(1);
if (!t) return -1;
wait_event_interruptible_timeout(sunkbd->wait, sunkbd->reset >= 0, HZ);
if (sunkbd->reset <0)
return -1;
sunkbd->type = sunkbd->reset;
if (sunkbd->type == 4) { /* Type 4 keyboard */
t = 250;
sunkbd->layout = -2;
sunkbd->serio->write(sunkbd->serio, SUNKBD_CMD_LAYOUT);
while (sunkbd->layout < 0 && --t) mdelay(1);
if (!t) return -1;
wait_event_interruptible_timeout(sunkbd->wait, sunkbd->layout >= 0, HZ/4);
if (sunkbd->layout < 0) return -1;
if (sunkbd->layout & SUNKBD_LAYOUT_5_MASK) sunkbd->type = 5;
}
......@@ -206,9 +206,8 @@ static int sunkbd_initialize(struct sunkbd *sunkbd)
static void sunkbd_reinit(void *data)
{
struct sunkbd *sunkbd = data;
int t = 1000;
while (sunkbd->reset < 0 && --t) mdelay(1);
wait_event_interruptible_timeout(sunkbd->wait, sunkbd->reset >= 0, HZ);
sunkbd->serio->write(sunkbd->serio, SUNKBD_CMD_SETLED);
sunkbd->serio->write(sunkbd->serio,
......@@ -239,6 +238,7 @@ static void sunkbd_connect(struct serio *serio, struct serio_dev *dev)
memset(sunkbd, 0, sizeof(struct sunkbd));
init_input_dev(&sunkbd->dev);
init_waitqueue_head(&sunkbd->wait);
sunkbd->dev.evbit[0] = BIT(EV_KEY) | BIT(EV_LED) | BIT(EV_SND) | BIT(EV_REP);
sunkbd->dev.ledbit[0] = BIT(LED_CAPSL) | BIT(LED_COMPOSE) | BIT(LED_SCROLLL) | BIT(LED_NUML);
......@@ -275,7 +275,7 @@ static void sunkbd_connect(struct serio *serio, struct serio_dev *dev)
set_bit(sunkbd->keycode[i], sunkbd->dev.keybit);
clear_bit(0, sunkbd->dev.keybit);
sprintf(sunkbd->name, "%s/input", serio->phys);
sprintf(sunkbd->phys, "%s/input0", serio->phys);
sunkbd->dev.name = sunkbd->name;
sunkbd->dev.phys = sunkbd->phys;
......
......@@ -54,12 +54,3 @@ config INPUT_UINPUT
To compile this driver as a module, choose M here: the
module will be called uinput.
config INPUT_GSC
tristate "PA-RISC GSC PS/2 keyboard/mouse support"
depends on GSC && INPUT && INPUT_MISC
help
Say Y here if you have a PS/2 keyboard and/or mouse attached
to your PA-RISC box. HP run the keyboard in AT mode rather than
XT mode like everyone else, so we need our own driver.
Furthermore, the GSC PS/2 controller shares IRQ between mouse and
keyboard.
......@@ -9,4 +9,3 @@ obj-$(CONFIG_INPUT_PCSPKR) += pcspkr.o
obj-$(CONFIG_INPUT_M68K_BEEP) += m68kspkr.o
obj-$(CONFIG_INPUT_98SPKR) += 98spkr.o
obj-$(CONFIG_INPUT_UINPUT) += uinput.o
obj-$(CONFIG_INPUT_GSC) += gsc_ps2.o
This diff is collapsed.
......@@ -74,6 +74,8 @@ static int pc98bm_irq = PC98BM_IRQ;
module_param_named(irq, pc98bm_irq, uint, 0);
MODULE_PARM_DESC(irq, "IRQ number (13=default)");
__obsolete_setup("pc98bm_irq=");
static int pc98bm_used = 0;
static irqreturn_t pc98bm_interrupt(int irq, void *dev_id, struct pt_regs *regs);
......
......@@ -17,6 +17,7 @@ config MOUSE_PS2
depends on INPUT && INPUT_MOUSE
select SERIO
select SERIO_I8042 if PC
select SERIO_GSCPS2 if GSC
---help---
Say Y here if you have a PS/2 mouse connected to your system. This
includes the standard 2 or 3-button PS/2 mouse, as well as PS/2
......@@ -117,6 +118,19 @@ config MOUSE_RISCPC
To compile this driver as a module, choose M here: the
module will be called rpcmouse.
config MOUSE_VSXXXAA
tristate "DEC VSXXX-AA/GA mouse and tablet"
depends on INPUT && INPUT_MOUSE
select SERIO
help
Say Y (or M) if you want to use a DEC VSXXX-AA (hockey
puck) or a VSXXX-GA (rectangular) mouse. Theses mice are
typically used on DECstations or VAXstations, but can also
be used on any box capable of RS232 (with some adaptor
described in the source file). This driver should, in theory,
also work with the digitizer DEC produced, but it isn't tested
with that (I don't have the hardware yet).
config MOUSE_PC9800
tristate "NEC PC-9800 busmouse"
depends on X86_PC9800 && INPUT && INPUT_MOUSE && ISA
......
......@@ -13,5 +13,6 @@ obj-$(CONFIG_MOUSE_PC110PAD) += pc110pad.o
obj-$(CONFIG_MOUSE_PC9800) += 98busmouse.o
obj-$(CONFIG_MOUSE_PS2) += psmouse.o
obj-$(CONFIG_MOUSE_SERIAL) += sermouse.o
obj-$(CONFIG_MOUSE_VSXXXAA) += vsxxxaa.o
psmouse-objs := psmouse-base.o logips2pp.o synaptics.o
......@@ -85,6 +85,8 @@ static int inport_irq = INPORT_IRQ;
module_param_named(irq, inport_irq, uint, 0);
MODULE_PARM_DESC(irq, "IRQ number (5=default)");
__obsolete_setup("inport_irq=");
static int inport_used;
static irqreturn_t inport_interrupt(int irq, void *dev_id, struct pt_regs *regs);
......
......@@ -75,6 +75,8 @@ static int logibm_irq = LOGIBM_IRQ;
module_param_named(irq, logibm_irq, uint, 0);
MODULE_PARM_DESC(irq, "IRQ number (5=default)");
__obsolete_setup("logibm_irq=");
static int logibm_used = 0;
static irqreturn_t logibm_interrupt(int irq, void *dev_id, struct pt_regs *regs);
......
......@@ -47,6 +47,12 @@ unsigned int psmouse_resetafter;
module_param_named(resetafter, psmouse_resetafter, uint, 0);
MODULE_PARM_DESC(resetafter, "Reset Synaptics Touchpad after so many bad packets (0 = never).");
__obsolete_setup("psmouse_noext");
__obsolete_setup("psmouse_resolution=");
__obsolete_setup("psmouse_smartscroll=");
__obsolete_setup("psmouse_resetafter=");
__obsolete_setup("psmouse_rate=");
static char *psmouse_protocols[] = { "None", "PS/2", "PS2++", "PS2T++", "GenPS/2", "ImPS/2", "ImExPS/2", "SynPS/2"};
/*
......@@ -163,14 +169,14 @@ static irqreturn_t psmouse_interrupt(struct serio *serio,
psmouse->name, psmouse->phys, psmouse->pktcnt);
psmouse->pktcnt = 0;
}
psmouse->last = jiffies;
psmouse->packet[psmouse->pktcnt++] = data;
if (psmouse->packet[0] == PSMOUSE_RET_BAT) {
if (psmouse->pktcnt == 1)
goto out;
if (psmouse->pktcnt == 2) {
if (psmouse->packet[1] == PSMOUSE_RET_ID) {
psmouse->state = PSMOUSE_IGNORE;
......@@ -258,7 +264,7 @@ int psmouse_command(struct psmouse *psmouse, unsigned char *param, int command)
return (psmouse->cmdcnt = 0) - 1;
while (psmouse->cmdcnt && timeout--) {
if (psmouse->cmdcnt == 1 && command == PSMOUSE_CMD_RESET_BAT &&
timeout > 100000) /* do not run in a endless loop */
timeout = 100000; /* 1 sec */
......@@ -442,7 +448,7 @@ static int psmouse_probe(struct psmouse *psmouse)
*/
if (psmouse_command(psmouse, NULL, PSMOUSE_CMD_RESET_DIS))
return -1;
printk(KERN_WARNING "psmouse.c: Failed to reset mouse on %s\n", psmouse->serio->phys);
/*
* And here we try to determine if it has any extensions over the
......@@ -497,7 +503,7 @@ static void psmouse_set_rate(struct psmouse *psmouse)
static void psmouse_initialize(struct psmouse *psmouse)
{
unsigned char param[2];
/*
* We set the mouse report rate, resolution and scaling.
*/
......@@ -571,7 +577,7 @@ static void psmouse_disconnect(struct serio *serio)
static void psmouse_connect(struct serio *serio, struct serio_dev *dev)
{
struct psmouse *psmouse;
if ((serio->type & SERIO_TYPE) != SERIO_8042 &&
(serio->type & SERIO_TYPE) != SERIO_PS_PSTHRU)
return;
......@@ -603,7 +609,7 @@ static void psmouse_connect(struct serio *serio, struct serio_dev *dev)
serio->private = NULL;
return;
}
sprintf(psmouse->devname, "%s %s %s",
psmouse_protocols[psmouse->type], psmouse->vendor, psmouse->name);
sprintf(psmouse->phys, "%s/input0",
......@@ -617,7 +623,7 @@ static void psmouse_connect(struct serio *serio, struct serio_dev *dev)
psmouse->dev.id.version = psmouse->model;
input_register_device(&psmouse->dev);
printk(KERN_INFO "input: %s on %s\n", psmouse->devname, serio->phys);
psmouse_initialize(psmouse);
......
......@@ -435,6 +435,8 @@ int synaptics_init(struct psmouse *psmouse)
goto init_fail;
}
priv->pkt_type = SYN_MODEL_NEWABS(priv->model_id) ? SYN_NEWABS : SYN_OLDABS;
if (SYN_CAP_EXTENDED(priv->capabilities) && SYN_CAP_PASS_THROUGH(priv->capabilities))
synaptics_pt_create(psmouse);
......@@ -602,19 +604,42 @@ static void synaptics_process_packet(struct psmouse *psmouse)
input_sync(dev);
}
static int synaptics_validate_byte(struct psmouse *psmouse)
static int synaptics_validate_byte(unsigned char packet[], int idx, unsigned char pkt_type)
{
static unsigned char newabs_mask[] = { 0xC0, 0x00, 0x00, 0xC0, 0x00 };
static unsigned char newabs_rslt[] = { 0x80, 0x00, 0x00, 0xC0, 0x00 };
static unsigned char oldabs_mask[] = { 0xC0, 0x60, 0x00, 0xC0, 0x60 };
static unsigned char oldabs_rslt[] = { 0xC0, 0x00, 0x00, 0x80, 0x00 };
struct synaptics_data *priv = psmouse->private;
int idx = psmouse->pktcnt - 1;
static unsigned char newabs_mask[] = { 0xC8, 0x00, 0x00, 0xC8, 0x00 };
static unsigned char newabs_rel_mask[] = { 0xC0, 0x00, 0x00, 0xC0, 0x00 };
static unsigned char newabs_rslt[] = { 0x80, 0x00, 0x00, 0xC0, 0x00 };
static unsigned char oldabs_mask[] = { 0xC0, 0x60, 0x00, 0xC0, 0x60 };
static unsigned char oldabs_rslt[] = { 0xC0, 0x00, 0x00, 0x80, 0x00 };
if (SYN_MODEL_NEWABS(priv->model_id))
return (psmouse->packet[idx] & newabs_mask[idx]) == newabs_rslt[idx];
else
return (psmouse->packet[idx] & oldabs_mask[idx]) == oldabs_rslt[idx];
switch (pkt_type) {
case SYN_NEWABS:
case SYN_NEWABS_RELAXED:
return (packet[idx] & newabs_rel_mask[idx]) == newabs_rslt[idx];
case SYN_NEWABS_STRICT:
return (packet[idx] & newabs_mask[idx]) == newabs_rslt[idx];
case SYN_OLDABS:
return (packet[idx] & oldabs_mask[idx]) == oldabs_rslt[idx];
default:
printk(KERN_ERR "synaptics: unknown packet type %d\n", pkt_type);
return 0;
}
}
static unsigned char synaptics_detect_pkt_type(struct psmouse *psmouse)
{
int i;
for (i = 0; i < 5; i++)
if (!synaptics_validate_byte(psmouse->packet, i, SYN_NEWABS_STRICT)) {
printk(KERN_INFO "synaptics: using relaxed packet validation\n");
return SYN_NEWABS_RELAXED;
}
return SYN_NEWABS_STRICT;
}
void synaptics_process_byte(struct psmouse *psmouse, struct pt_regs *regs)
......@@ -630,13 +655,17 @@ void synaptics_process_byte(struct psmouse *psmouse, struct pt_regs *regs)
printk(KERN_NOTICE "Synaptics driver resynced.\n");
}
if (unlikely(priv->pkt_type == SYN_NEWABS))
priv->pkt_type = synaptics_detect_pkt_type(psmouse);
if (psmouse->ptport && psmouse->ptport->serio.dev && synaptics_is_pt_packet(psmouse->packet))
synaptics_pass_pt_packet(&psmouse->ptport->serio, psmouse->packet);
else
synaptics_process_packet(psmouse);
psmouse->pktcnt = 0;
} else if (psmouse->pktcnt && !synaptics_validate_byte(psmouse)) {
} else if (psmouse->pktcnt &&
!synaptics_validate_byte(psmouse->packet, psmouse->pktcnt - 1, priv->pkt_type)) {
printk(KERN_WARNING "Synaptics driver lost sync at byte %d\n", psmouse->pktcnt);
psmouse->pktcnt = 0;
if (++priv->out_of_sync == psmouse_resetafter) {
......
......@@ -70,6 +70,12 @@ extern int synaptics_init(struct psmouse *psmouse);
#define SYN_PS_SET_MODE2 0x14
#define SYN_PS_CLIENT_CMD 0x28
/* synaptics packet types */
#define SYN_NEWABS 0
#define SYN_NEWABS_STRICT 1
#define SYN_NEWABS_RELAXED 2
#define SYN_OLDABS 3
/*
* A structure to describe the state of the touchpad hardware (buttons and pad)
*/
......@@ -103,6 +109,7 @@ struct synaptics_data {
/* Data for normal processing */
unsigned int out_of_sync; /* # of packets out of sync */
int old_w; /* Previous w value */
unsigned char pkt_type; /* packet type - old, new, etc */
};
#endif /* _SYNAPTICS_H */
This diff is collapsed.
......@@ -20,6 +20,7 @@ config SERIO_I8042
tristate "i8042 PC Keyboard controller" if EMBEDDED || !X86
default y
select SERIO
depends on !PARISC
---help---
i8042 is the chip over which the standard AT keyboard and PS/2
mouse are connected to the computer. If you use these devices,
......@@ -48,6 +49,7 @@ config SERIO_SERPORT
config SERIO_CT82C710
tristate "ct82c710 Aux port controller"
depends on SERIO
depends on !PARISC
---help---
Say Y here if you have a Texas Instruments TravelMate notebook
equipped with the ct82c710 chip and want to use a mouse connected
......@@ -105,6 +107,20 @@ config SERIO_98KBD
To compile this driver as a module, choose M here: the
module will be called 98kbd-io.
config SERIO_GSCPS2
tristate "HP GSC PS/2 keyboard and PS/2 mouse controller"
depends on GSC && SERIO
default y
help
This driver provides support for the PS/2 ports on PA-RISC machines
over which HP PS/2 keyboards and PS/2 mice may be connected.
If you use these devices, you'll need to say Y here.
It's safe to enable this driver, so if unsure, say Y.
To compile this driver as a module, choose M here: the
module will be called gscps2.
config SERIO_PCIPS2
tristate "PCI PS/2 keyboard and PS/2 mouse controller"
depends on PCI && SERIO
......
......@@ -14,4 +14,5 @@ obj-$(CONFIG_SERIO_SA1111) += sa1111ps2.o
obj-$(CONFIG_SERIO_AMBAKMI) += ambakmi.o
obj-$(CONFIG_SERIO_Q40KBD) += q40kbd.o
obj-$(CONFIG_SERIO_98KBD) += 98kbd-io.o
obj-$(CONFIG_SERIO_GSCPS2) += gscps2.o
obj-$(CONFIG_SERIO_PCIPS2) += pcips2.o
This diff is collapsed.
......@@ -25,6 +25,9 @@
#elif defined(__ia64__)
# define I8042_KBD_IRQ isa_irq_to_vector(1)
# define I8042_AUX_IRQ isa_irq_to_vector(12)
#elif defined(__arm__)
/* defined in include/asm-arm/arch-xxx/irqs.h */
#include <asm/irq.h>
#else
# define I8042_KBD_IRQ 1
# define I8042_AUX_IRQ 12
......
......@@ -52,6 +52,13 @@ static unsigned int i8042_dumbkbd;
module_param_named(dumbkbd, i8042_dumbkbd, bool, 0);
MODULE_PARM_DESC(dumbkbd, "Pretend that controller can only read data from keyboard");
__obsolete_setup("i8042_noaux");
__obsolete_setup("i8042_nomux");
__obsolete_setup("i8042_unlock");
__obsolete_setup("i8042_reset");
__obsolete_setup("i8042_direct");
__obsolete_setup("i8042_dumbkbd");
#undef DEBUG
#include "i8042.h"
......@@ -379,6 +386,8 @@ static irqreturn_t i8042_interrupt(int irq, void *dev_id, struct pt_regs *regs)
unsigned int dfl;
int ret;
mod_timer(&i8042_timer, jiffies + I8042_POLL_PERIOD);
spin_lock_irqsave(&i8042_lock, flags);
str = i8042_read_status();
if (str & I8042_STR_OBF)
......@@ -433,7 +442,6 @@ static irqreturn_t i8042_interrupt(int irq, void *dev_id, struct pt_regs *regs)
irq_ret:
ret = 1;
out:
mod_timer(&i8042_timer, jiffies + I8042_POLL_PERIOD);
return IRQ_RETVAL(ret);
}
......@@ -522,6 +530,11 @@ static int __init i8042_check_mux(struct i8042_values *values)
if (i8042_enable_mux_mode(values, &mux_version))
return -1;
/* Workaround for broken chips which seem to support MUX, but in reality don't. */
/* They all report version 12.10 */
if (mux_version == 0xCA)
return -1;
printk(KERN_INFO "i8042.c: Detected active multiplexing controller, rev %d.%d.\n",
(mux_version >> 4) & 0xf, mux_version & 0xf);
......@@ -708,14 +721,6 @@ static int i8042_controller_init(void)
printk(KERN_WARNING "i8042.c: Warning: Keylock active.\n");
}
/*
* If the chip is configured into nontranslated mode by the BIOS, don't
* bother enabling translating and be happy.
*/
if (~i8042_ctr & I8042_CTR_XLATE)
i8042_direct = 1;
/*
* Set nontranslated mode for the kbd interface if requested by an option.
* After this the kbd interface becomes a simple serial in/out, like the aux
......
......@@ -195,6 +195,9 @@ irqreturn_t serio_interrupt(struct serio *serio,
ret = serio->dev->interrupt(serio, data, flags, regs);
} else {
if (!flags) {
if ((serio->type == SERIO_8042 ||
serio->type == SERIO_8042_XL) && (data != 0xaa))
return ret;
serio_rescan(serio);
ret = IRQ_HANDLED;
}
......
......@@ -224,6 +224,9 @@ static int hid_add_field(struct hid_parser *parser, unsigned report_type, unsign
offset = report->size;
report->size += parser->global.report_size * parser->global.report_count;
if (usages < parser->global.report_count)
usages = parser->global.report_count;
if (usages == 0)
return 0; /* ignore padding fields */
......@@ -235,9 +238,13 @@ static int hid_add_field(struct hid_parser *parser, unsigned report_type, unsign
field->application = hid_lookup_collection(parser, HID_COLLECTION_APPLICATION);
for (i = 0; i < usages; i++) {
field->usage[i].hid = parser->local.usage[i];
int j = i;
/* Duplicate the last usage we parsed if we have excess values */
if (i >= parser->local.usage_index)
j = parser->local.usage_index - 1;
field->usage[i].hid = parser->local.usage[j];
field->usage[i].collection_index =
parser->local.collection_index[i];
parser->local.collection_index[j];
}
field->maxusage = usages;
......@@ -1317,7 +1324,6 @@ void hid_init_reports(struct hid_device *hid)
#define USB_VENDOR_ID_KBGEAR 0x084e
#define USB_DEVICE_ID_KBGEAR_JAMSTUDIO 0x1001
#define USB_VENDOR_ID_AIPTEK 0x08ca
#define USB_DEVICE_ID_AIPTEK_6000 0x0020
......@@ -1356,17 +1362,43 @@ void hid_init_reports(struct hid_device *hid)
#define USB_VENDOR_ID_A4TECH 0x09DA
#define USB_DEVICE_ID_A4TECH_WCP32PU 0x0006
#define USB_VENDOR_ID_CYPRESS 0x04b4
#define USB_DEVICE_ID_CYPRESS_MOUSE 0x0001
#define USB_VENDOR_ID_BERKSHIRE 0x0c98
#define USB_DEVICE_ID_BERKSHIRE_PCWD 0x1140
#define USB_VENDOR_ID_ALPS 0x0433
#define USB_DEVICE_ID_IBM_GAMEPAD 0x1101
#define USB_VENDOR_ID_SAITEK 0x06a3
#define USB_DEVICE_ID_SAITEK_RUMBLEPAD 0xff17
#define USB_VENDOR_ID_NEC 0x073e
#define USB_DEVICE_ID_NEC_USB_GAME_PAD 0x0301
struct hid_blacklist {
__u16 idVendor;
__u16 idProduct;
unsigned quirks;
} hid_blacklist[] = {
{ USB_VENDOR_ID_AIPTEK, USB_DEVICE_ID_AIPTEK_6000, HID_QUIRK_IGNORE },
{ USB_VENDOR_ID_BERKSHIRE, USB_DEVICE_ID_BERKSHIRE_PCWD, HID_QUIRK_IGNORE },
{ USB_VENDOR_ID_ESSENTIAL_REALITY, USB_DEVICE_ID_ESSENTIAL_REALITY_P5, HID_QUIRK_IGNORE },
{ USB_VENDOR_ID_KBGEAR, USB_DEVICE_ID_KBGEAR_JAMSTUDIO, HID_QUIRK_IGNORE },
{ USB_VENDOR_ID_GRIFFIN, USB_DEVICE_ID_POWERMATE, HID_QUIRK_IGNORE },
{ USB_VENDOR_ID_GRIFFIN, USB_DEVICE_ID_SOUNDKNOB, HID_QUIRK_IGNORE },
{ USB_VENDOR_ID_MGE, USB_DEVICE_ID_MGE_UPS, HID_QUIRK_IGNORE },
{ USB_VENDOR_ID_MGE, USB_DEVICE_ID_MGE_UPS1, HID_QUIRK_IGNORE },
{ USB_VENDOR_ID_ONTRAK, USB_DEVICE_ID_ONTRAK_ADU100, HID_QUIRK_IGNORE },
{ USB_VENDOR_ID_ONTRAK, USB_DEVICE_ID_ONTRAK_ADU100 + 100, HID_QUIRK_IGNORE },
{ USB_VENDOR_ID_ONTRAK, USB_DEVICE_ID_ONTRAK_ADU100 + 200, HID_QUIRK_IGNORE },
{ USB_VENDOR_ID_ONTRAK, USB_DEVICE_ID_ONTRAK_ADU100 + 300, HID_QUIRK_IGNORE },
{ USB_VENDOR_ID_ONTRAK, USB_DEVICE_ID_ONTRAK_ADU100 + 400, HID_QUIRK_IGNORE },
{ USB_VENDOR_ID_ONTRAK, USB_DEVICE_ID_ONTRAK_ADU100 + 500, HID_QUIRK_IGNORE },
{ USB_VENDOR_ID_WACOM, USB_DEVICE_ID_WACOM_PENPARTNER, HID_QUIRK_IGNORE },
{ USB_VENDOR_ID_WACOM, USB_DEVICE_ID_WACOM_GRAPHIRE, HID_QUIRK_IGNORE },
{ USB_VENDOR_ID_WACOM, USB_DEVICE_ID_WACOM_GRAPHIRE + 1, HID_QUIRK_IGNORE },
......@@ -1388,32 +1420,25 @@ struct hid_blacklist {
{ USB_VENDOR_ID_WACOM, USB_DEVICE_ID_WACOM_INTUOS2 + 2, HID_QUIRK_IGNORE },
{ USB_VENDOR_ID_WACOM, USB_DEVICE_ID_WACOM_INTUOS2 + 3, HID_QUIRK_IGNORE },
{ USB_VENDOR_ID_WACOM, USB_DEVICE_ID_WACOM_INTUOS2 + 4, HID_QUIRK_IGNORE },
{ USB_VENDOR_ID_KBGEAR, USB_DEVICE_ID_KBGEAR_JAMSTUDIO, HID_QUIRK_IGNORE },
{ USB_VENDOR_ID_AIPTEK, USB_DEVICE_ID_AIPTEK_6000, HID_QUIRK_IGNORE },
{ USB_VENDOR_ID_GRIFFIN, USB_DEVICE_ID_POWERMATE, HID_QUIRK_IGNORE },
{ USB_VENDOR_ID_GRIFFIN, USB_DEVICE_ID_SOUNDKNOB, HID_QUIRK_IGNORE },
{ USB_VENDOR_ID_ATEN, USB_DEVICE_ID_ATEN_UC100KM, HID_QUIRK_NOGET },
{ USB_VENDOR_ID_ATEN, USB_DEVICE_ID_ATEN_CS124U, HID_QUIRK_NOGET },
{ USB_VENDOR_ID_ATEN, USB_DEVICE_ID_ATEN_2PORTKVM, HID_QUIRK_NOGET },
{ USB_VENDOR_ID_ATEN, USB_DEVICE_ID_ATEN_4PORTKVM, HID_QUIRK_NOGET },
{ USB_VENDOR_ID_ATEN, USB_DEVICE_ID_ATEN_4PORTKVMC, HID_QUIRK_NOGET },
{ USB_VENDOR_ID_MGE, USB_DEVICE_ID_MGE_UPS, HID_QUIRK_IGNORE },
{ USB_VENDOR_ID_MGE, USB_DEVICE_ID_MGE_UPS1, HID_QUIRK_IGNORE },
{ USB_VENDOR_ID_TOPMAX, USB_DEVICE_ID_TOPMAX_COBRAPAD, HID_QUIRK_BADPAD },
{ USB_VENDOR_ID_HAPP, USB_DEVICE_ID_UGCI_DRIVING, HID_QUIRK_BADPAD|HID_QUIRK_MULTI_INPUT },
{ USB_VENDOR_ID_HAPP, USB_DEVICE_ID_UGCI_FLYING, HID_QUIRK_BADPAD|HID_QUIRK_MULTI_INPUT },
{ USB_VENDOR_ID_HAPP, USB_DEVICE_ID_UGCI_FIGHTING, HID_QUIRK_BADPAD|HID_QUIRK_MULTI_INPUT },
{ USB_VENDOR_ID_ONTRAK, USB_DEVICE_ID_ONTRAK_ADU100, HID_QUIRK_IGNORE },
{ USB_VENDOR_ID_ONTRAK, USB_DEVICE_ID_ONTRAK_ADU100 + 100, HID_QUIRK_IGNORE },
{ USB_VENDOR_ID_ONTRAK, USB_DEVICE_ID_ONTRAK_ADU100 + 200, HID_QUIRK_IGNORE },
{ USB_VENDOR_ID_ONTRAK, USB_DEVICE_ID_ONTRAK_ADU100 + 300, HID_QUIRK_IGNORE },
{ USB_VENDOR_ID_ONTRAK, USB_DEVICE_ID_ONTRAK_ADU100 + 400, HID_QUIRK_IGNORE },
{ USB_VENDOR_ID_ONTRAK, USB_DEVICE_ID_ONTRAK_ADU100 + 500, HID_QUIRK_IGNORE },
{ USB_VENDOR_ID_TANGTOP, USB_DEVICE_ID_TANGTOP_USBPS2, HID_QUIRK_NOGET },
{ USB_VENDOR_ID_ESSENTIAL_REALITY, USB_DEVICE_ID_ESSENTIAL_REALITY_P5, HID_QUIRK_IGNORE },
{ USB_VENDOR_ID_A4TECH, USB_DEVICE_ID_A4TECH_WCP32PU, HID_QUIRK_2WHEEL_MOUSE_HACK },
{ USB_VENDOR_ID_BERKSHIRE, USB_DEVICE_ID_BERKSHIRE_PCWD, HID_QUIRK_IGNORE },
{ USB_VENDOR_ID_A4TECH, USB_DEVICE_ID_A4TECH_WCP32PU, HID_QUIRK_2WHEEL_MOUSE_HACK_BACK },
{ USB_VENDOR_ID_CYPRESS, USB_DEVICE_ID_CYPRESS_MOUSE, HID_QUIRK_2WHEEL_MOUSE_HACK_EXTRA },
{ USB_VENDOR_ID_ALPS, USB_DEVICE_ID_IBM_GAMEPAD, HID_QUIRK_BADPAD },
{ USB_VENDOR_ID_HAPP, USB_DEVICE_ID_UGCI_DRIVING, HID_QUIRK_BADPAD | HID_QUIRK_MULTI_INPUT },
{ USB_VENDOR_ID_HAPP, USB_DEVICE_ID_UGCI_FLYING, HID_QUIRK_BADPAD | HID_QUIRK_MULTI_INPUT },
{ USB_VENDOR_ID_HAPP, USB_DEVICE_ID_UGCI_FIGHTING, HID_QUIRK_BADPAD | HID_QUIRK_MULTI_INPUT },
{ USB_VENDOR_ID_NEC, USB_DEVICE_ID_NEC_USB_GAME_PAD, HID_QUIRK_BADPAD },
{ USB_VENDOR_ID_SAITEK, USB_DEVICE_ID_SAITEK_RUMBLEPAD, HID_QUIRK_BADPAD },
{ USB_VENDOR_ID_TOPMAX, USB_DEVICE_ID_TOPMAX_COBRAPAD, HID_QUIRK_BADPAD },
{ 0, 0 }
};
......
......@@ -377,7 +377,8 @@ static void hidinput_configure_usage(struct hid_input *hidinput, struct hid_fiel
set_bit(usage->type, input->evbit);
if ((usage->type == EV_REL)
&& (device->quirks & HID_QUIRK_2WHEEL_MOUSE_HACK)
&& (device->quirks & (HID_QUIRK_2WHEEL_MOUSE_HACK_BACK
| HID_QUIRK_2WHEEL_MOUSE_HACK_EXTRA))
&& (usage->code == REL_WHEEL)) {
set_bit(REL_HWHEEL, bit);
}
......@@ -431,21 +432,22 @@ void hidinput_hid_event(struct hid_device *hid, struct hid_field *field, struct
input_regs(input, regs);
if ((hid->quirks & HID_QUIRK_2WHEEL_MOUSE_HACK)
&& (usage->code == BTN_BACK)) {
if (((hid->quirks & HID_QUIRK_2WHEEL_MOUSE_HACK_EXTRA) && (usage->code == BTN_EXTRA))
|| ((hid->quirks & HID_QUIRK_2WHEEL_MOUSE_HACK_BACK) && (usage->code == BTN_BACK))) {
if (value)
hid->quirks |= HID_QUIRK_2WHEEL_MOUSE_HACK_ON;
else
hid->quirks &= ~HID_QUIRK_2WHEEL_MOUSE_HACK_ON;
return;
}
if ((hid->quirks & HID_QUIRK_2WHEEL_MOUSE_HACK_ON)
&& (usage->code == REL_WHEEL)) {
input_event(input, usage->type, REL_HWHEEL, value);
return;
}
if (usage->hat_min != usage->hat_max) {
if (usage->hat_min != usage->hat_max ) { /* FIXME: hat_max can be 0 and hat_min 1 */
value = (value - usage->hat_min) * 8 / (usage->hat_max - usage->hat_min + 1) + 1;
if (value < 0 || value > 8) value = 0;
input_event(input, usage->type, usage->code , hid_hat_to_axis[value].x);
......@@ -484,7 +486,7 @@ void hidinput_hid_event(struct hid_device *hid, struct hid_field *field, struct
return;
}
if((usage->type == EV_KEY) && (usage->code == 0)) /* Key 0 is "unassigned", not KEY_UKNOWN */
if((usage->type == EV_KEY) && (usage->code == 0)) /* Key 0 is "unassigned", not KEY_UNKNOWN */
return;
input_event(input, usage->type, usage->code, value);
......
......@@ -201,15 +201,16 @@ struct hid_item {
* HID device quirks.
*/
#define HID_QUIRK_INVERT 0x001
#define HID_QUIRK_NOTOUCH 0x002
#define HID_QUIRK_IGNORE 0x004
#define HID_QUIRK_NOGET 0x008
#define HID_QUIRK_HIDDEV 0x010
#define HID_QUIRK_BADPAD 0x020
#define HID_QUIRK_MULTI_INPUT 0x040
#define HID_QUIRK_2WHEEL_MOUSE_HACK 0x080
#define HID_QUIRK_2WHEEL_MOUSE_HACK_ON 0x100
#define HID_QUIRK_INVERT 0x001
#define HID_QUIRK_NOTOUCH 0x002
#define HID_QUIRK_IGNORE 0x004
#define HID_QUIRK_NOGET 0x008
#define HID_QUIRK_HIDDEV 0x010
#define HID_QUIRK_BADPAD 0x020
#define HID_QUIRK_MULTI_INPUT 0x040
#define HID_QUIRK_2WHEEL_MOUSE_HACK_BACK 0x080
#define HID_QUIRK_2WHEEL_MOUSE_HACK_EXTRA 0x100
#define HID_QUIRK_2WHEEL_MOUSE_HACK_ON 0x200
/*
* This is the global environment of the parser. This information is
......
......@@ -403,7 +403,8 @@ static int hiddev_ioctl(struct inode *inode, struct file *file, unsigned int cmd
struct hiddev_collection_info cinfo;
struct hiddev_report_info rinfo;
struct hiddev_field_info finfo;
struct hiddev_usage_ref uref;
struct hiddev_usage_ref_multi uref_multi;
struct hiddev_usage_ref *uref = &uref_multi.uref;
struct hiddev_devinfo dinfo;
struct hid_report *report;
struct hid_field *field;
......@@ -575,68 +576,98 @@ static int hiddev_ioctl(struct inode *inode, struct file *file, unsigned int cmd
return 0;
case HIDIOCGUCODE:
if (copy_from_user(&uref, (void *) arg, sizeof(uref)))
if (copy_from_user(uref, (void *) arg, sizeof(*uref)))
return -EFAULT;
rinfo.report_type = uref.report_type;
rinfo.report_id = uref.report_id;
rinfo.report_type = uref->report_type;
rinfo.report_id = uref->report_id;
if ((report = hiddev_lookup_report(hid, &rinfo)) == NULL)
return -EINVAL;
if (uref.field_index >= report->maxfield)
if (uref->field_index >= report->maxfield)
return -EINVAL;
field = report->field[uref.field_index];
if (uref.usage_index >= field->maxusage)
field = report->field[uref->field_index];
if (uref->usage_index >= field->maxusage)
return -EINVAL;
uref.usage_code = field->usage[uref.usage_index].hid;
uref->usage_code = field->usage[uref->usage_index].hid;
if (copy_to_user((void *) arg, &uref, sizeof(uref)))
if (copy_to_user((void *) arg, uref, sizeof(*uref)))
return -EFAULT;
return 0;
case HIDIOCGUSAGE:
case HIDIOCSUSAGE:
case HIDIOCGUSAGES:
case HIDIOCSUSAGES:
case HIDIOCGCOLLECTIONINDEX:
if (copy_from_user(&uref, (void *) arg, sizeof(uref)))
return -EFAULT;
if (cmd == HIDIOCGUSAGES || cmd == HIDIOCSUSAGES) {
if (copy_from_user(&uref_multi, (void *) arg,
sizeof(uref_multi)))
return -EFAULT;
} else {
if (copy_from_user(uref, (void *) arg, sizeof(*uref)))
return -EFAULT;
}
if (cmd != HIDIOCGUSAGE && uref.report_type == HID_REPORT_TYPE_INPUT)
return -EINVAL;
if (cmd != HIDIOCGUSAGE &&
cmd != HIDIOCGUSAGES &&
uref->report_type == HID_REPORT_TYPE_INPUT)
return -EINVAL;
if (uref.report_id == HID_REPORT_ID_UNKNOWN) {
field = hiddev_lookup_usage(hid, &uref);
if (uref->report_id == HID_REPORT_ID_UNKNOWN) {
field = hiddev_lookup_usage(hid, uref);
if (field == NULL)
return -EINVAL;
} else {
rinfo.report_type = uref.report_type;
rinfo.report_id = uref.report_id;
rinfo.report_type = uref->report_type;
rinfo.report_id = uref->report_id;
if ((report = hiddev_lookup_report(hid, &rinfo)) == NULL)
return -EINVAL;
if (uref.field_index >= report->maxfield)
if (uref->field_index >= report->maxfield)
return -EINVAL;
field = report->field[uref.field_index];
if (uref.usage_index >= field->maxusage)
field = report->field[uref->field_index];
if (uref->usage_index >= field->maxusage)
return -EINVAL;
if (cmd == HIDIOCGUSAGES || cmd == HIDIOCSUSAGES) {
if (uref_multi.num_values >= HID_MAX_USAGES ||
uref->usage_index >= field->maxusage ||
(uref->usage_index + uref_multi.num_values) >= field->maxusage)
return -EINVAL;
}
}
switch (cmd) {
case HIDIOCGUSAGE:
uref.value = field->value[uref.usage_index];
if (copy_to_user((void *) arg, &uref, sizeof(uref)))
uref->value = field->value[uref->usage_index];
if (copy_to_user((void *) arg, uref, sizeof(*uref)))
return -EFAULT;
return 0;
case HIDIOCSUSAGE:
field->value[uref.usage_index] = uref.value;
field->value[uref->usage_index] = uref->value;
return 0;
case HIDIOCGCOLLECTIONINDEX:
return field->usage[uref.usage_index].collection_index;
return field->usage[uref->usage_index].collection_index;
case HIDIOCGUSAGES:
for (i = 0; i < uref_multi.num_values; i++)
uref_multi.values[i] =
field->value[uref->usage_index + i];
if (copy_to_user((void *) arg, &uref_multi,
sizeof(uref_multi)))
return -EFAULT;
return 0;
case HIDIOCSUSAGES:
for (i = 0; i < uref_multi.num_values; i++)
field->value[uref->usage_index + i] =
uref_multi.values[i];
return 0;
}
return 0;
......
/*
* USB Wacom Graphire and Wacom Intuos tablet support
*
* Copyright (c) 2000-2002 Vojtech Pavlik <vojtech@ucw.cz>
* Copyright (c) 2000-2004 Vojtech Pavlik <vojtech@ucw.cz>
* Copyright (c) 2000 Andreas Bach Aaen <abach@stofanet.dk>
* Copyright (c) 2000 Clifford Wolf <clifford@clifford.at>
* Copyright (c) 2000 Sam Mosel <sam.mosel@computer.org>
......@@ -9,6 +9,7 @@
* Copyright (c) 2000 Daniel Egger <egger@suse.de>
* Copyright (c) 2001 Frederic Lepied <flepied@mandrakesoft.com>
* Copyright (c) 2002 Ping Cheng <pingc@wacom.com>
* Copyright (c) 2004 Panagiotis Issaris <panagiotis.issaris@mech.kuleuven.ac.be>
*
* ChangeLog:
* v0.1 (vp) - Initial release
......@@ -48,6 +49,7 @@
* v1.30 (vp) - Merge 2.4 and 2.5 drivers
* - Since 2.5 now has input_sync(), remove MSC_SERIAL abuse
* - Cleanups here and there
* v1.30.1 (pi) - Added Graphire3 support
*/
/*
......
......@@ -91,8 +91,8 @@
#undef RTC_IRQ
#define RTC_IRQ IRQ_ISA_RTC_ALARM
#undef AUX_IRQ
#define AUX_IRQ (machine_is_netwinder() ? IRQ_NETWINDER_PS2MOUSE : IRQ_ISA_PS2MOUSE)
#define I8042_KBD_IRQ IRQ_ISA_KEYBOARD
#define I8042_AUX_IRQ (machine_is_netwinder() ? IRQ_NETWINDER_PS2MOUSE : IRQ_ISA_PS2MOUSE)
#define IRQ_FLOPPYDISK IRQ_ISA_FLOPPY
#define irq_canonicalize(_i) (((_i) == IRQ_ISA_CASCADE) ? IRQ_ISA_2 : _i)
......@@ -8,5 +8,6 @@
#define IRQ_ISA_KEYBOARD 1
#define RTC_IRQ 8
#define AUX_IRQ 12
#define I8042_KBD_IRQ 1
#define I8042_AUX_IRQ 12
#define IRQ_HARDDISK 14
......@@ -39,33 +39,33 @@ struct hiddev_event {
};
struct hiddev_devinfo {
unsigned int bustype;
unsigned int busnum;
unsigned int devnum;
unsigned int ifnum;
short vendor;
short product;
short version;
unsigned num_applications;
__u32 bustype;
__u32 busnum;
__u32 devnum;
__u32 ifnum;
__s16 vendor;
__s16 product;
__s16 version;
__u32 num_applications;
};
struct hiddev_collection_info {
unsigned index;
unsigned type;
unsigned usage;
unsigned level;
__u32 index;
__u32 type;
__u32 usage;
__u32 level;
};
#define HID_STRING_SIZE 256
struct hiddev_string_descriptor {
int index;
__s32 index;
char value[HID_STRING_SIZE];
};
struct hiddev_report_info {
unsigned report_type;
unsigned report_id;
unsigned num_fields;
__u32 report_type;
__u32 report_id;
__u32 num_fields;
};
/* To do a GUSAGE/SUSAGE, fill in at least usage_code, report_type and
......@@ -88,20 +88,20 @@ struct hiddev_report_info {
#define HID_REPORT_TYPE_MAX 3
struct hiddev_field_info {
unsigned report_type;
unsigned report_id;
unsigned field_index;
unsigned maxusage;
unsigned flags;
unsigned physical; /* physical usage for this field */
unsigned logical; /* logical usage for this field */
unsigned application; /* application usage for this field */
__u32 report_type;
__u32 report_id;
__u32 field_index;
__u32 maxusage;
__u32 flags;
__u32 physical; /* physical usage for this field */
__u32 logical; /* logical usage for this field */
__u32 application; /* application usage for this field */
__s32 logical_minimum;
__s32 logical_maximum;
__s32 physical_minimum;
__s32 physical_maximum;
unsigned unit_exponent;
unsigned unit;
__u32 unit_exponent;
__u32 unit;
};
/* Fill in report_type, report_id and field_index to get the information on a
......@@ -118,14 +118,22 @@ struct hiddev_field_info {
#define HID_FIELD_BUFFERED_BYTE 0x100
struct hiddev_usage_ref {
unsigned report_type;
unsigned report_id;
unsigned field_index;
unsigned usage_index;
unsigned usage_code;
__u32 report_type;
__u32 report_id;
__u32 field_index;
__u32 usage_index;
__u32 usage_code;
__s32 value;
};
/* hiddev_usage_ref_multi is used for sending multiple bytes to a control.
* It really manifests itself as setting the value of consecutive usages */
struct hiddev_usage_ref_multi {
struct hiddev_usage_ref uref;
__u32 num_values;
__s32 values[HID_MAX_USAGES];
};
/* FIELD_INDEX_NONE is returned in read() data from the kernel when flags
* is set to (HIDDEV_FLAG_UREF | HIDDEV_FLAG_REPORT) and a new report has
* been sent by the device
......@@ -161,6 +169,10 @@ struct hiddev_usage_ref {
#define HIDIOCGCOLLECTIONINFO _IOWR('H', 0x11, struct hiddev_collection_info)
#define HIDIOCGPHYS(len) _IOC(_IOC_READ, 'H', 0x12, len)
/* For writing/reading to multiple/consecutive usages */
#define HIDIOCGUSAGES _IOWR('H', 0x13, struct hiddev_usage_ref_multi)
#define HIDIOCSUSAGES _IOW('H', 0x14, struct hiddev_usage_ref_multi)
/*
* Flags to be used in HIDIOCSFLAG
*/
......
......@@ -110,12 +110,21 @@ struct obs_kernel_param {
};
/* OBSOLETE: see moduleparam.h for the right way. */
#define __setup(str, fn) \
static char __setup_str_##fn[] __initdata = str; \
static struct obs_kernel_param __setup_##fn \
#define __setup_param(str, unique_id, fn) \
static char __setup_str_##unique_id[] __initdata = str; \
static struct obs_kernel_param __setup_##unique_id \
__attribute_used__ \
__attribute__((__section__(".init.setup"))) \
= { __setup_str_##fn, fn }
= { __setup_str_##unique_id, fn }
#define __setup_null_param(str, unique_id) \
__setup_param(str, unique_id, NULL)
#define __setup(str, fn) \
__setup_param(str, fn, fn)
#define __obsolete_setup(str) \
__setup_null_param(str, __LINE__)
#endif /* __ASSEMBLY__ */
......@@ -172,7 +181,10 @@ struct obs_kernel_param {
{ return exitfn; } \
void cleanup_module(void) __attribute__((alias(#exitfn)));
#define __setup(str,func) /* nothing */
#define __setup_param(str, unique_id, fn) /* nothing */
#define __setup_null_param(str, unique_id) /* nothing */
#define __setup(str, func) /* nothing */
#define __obsolete_setup(str) /* nothing */
#endif
/* Data marked not to be saved by software_suspend() */
......
......@@ -3,7 +3,6 @@
#include <linux/module.h>
#include <linux/major.h>
#define BUSMOUSE_MINOR 0
#define PSMOUSE_MINOR 1
#define MS_BUSMOUSE_MINOR 2
#define ATIXL_BUSMOUSE_MINOR 3
......
......@@ -126,13 +126,16 @@ extern int param_get_invbool(char *buffer, struct kernel_param *kp);
#define param_check_invbool(name, p) __param_check(name, p, int)
/* Comma-separated array: num is set to number they actually specified. */
#define module_param_array(name, type, num, perm) \
#define module_param_array_named(name, array, type, num, perm) \
static struct kparam_array __param_arr_##name \
= { ARRAY_SIZE(name), &num, param_set_##type, param_get_##type, \
sizeof(name[0]), name }; \
= { ARRAY_SIZE(array), &num, param_set_##type, param_get_##type,\
sizeof(array[0]), array }; \
module_param_call(name, param_array_set, param_array_get, \
&__param_arr_##name, perm)
#define module_param_array(name, type, num, perm) \
module_param_array_named(name, name, type, num, perm)
extern int param_array_set(const char *val, struct kernel_param *kp);
extern int param_array_get(char *buffer, struct kernel_param *kp);
......
......@@ -117,6 +117,7 @@ static __inline__ void serio_cleanup(struct serio *serio)
#define SERIO_MZ 0x05
#define SERIO_MZP 0x06
#define SERIO_MZPP 0x07
#define SERIO_VSXXXAA 0x08
#define SERIO_SUNKBD 0x10
#define SERIO_WARRIOR 0x18
#define SERIO_SPACEORB 0x19
......@@ -134,6 +135,7 @@ static __inline__ void serio_cleanup(struct serio *serio)
#define SERIO_HIL 0x25
#define SERIO_SNES232 0x26
#define SERIO_SEMTECH 0x27
#define SERIO_LKKBD 0x28
#define SERIO_ID 0xff00UL
#define SERIO_EXTRA 0xff0000UL
......
......@@ -155,8 +155,11 @@ static int __init obsolete_checksetup(char *line)
p = &__setup_start;
do {
int n = strlen(p->str);
if (!strncmp(line,p->str,n)) {
if (p->setup_func(line+n))
if (!strncmp(line, p->str, n)) {
if (!p->setup_func) {
printk(KERN_WARNING "Parameter %s is obsolete, ignored\n", p->str);
return 1;
} else if (p->setup_func(line + n))
return 1;
}
p++;
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment