ARM: 6459/2: sa1100: Add nanoEngine PCI support.

This patch adds nanoEngine's PCI support.
Signed-off-by: Marcelo Roberto Jimenez <mroberto@cpti.cetuc.puc-rio.br>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

arch/arm/Kconfig

@@ -1164,7 +1164,7 @@ config ISA_DMA_API
 	bool
 
 config PCI
-	bool "PCI support" if ARCH_INTEGRATOR_AP || ARCH_VERSATILE_PB || ARCH_IXP4XX || ARCH_KS8695 || MACH_ARMCORE || ARCH_CNS3XXX
+	bool "PCI support" if ARCH_INTEGRATOR_AP || ARCH_VERSATILE_PB || ARCH_IXP4XX || ARCH_KS8695 || MACH_ARMCORE || ARCH_CNS3XXX || SA1100_NANOENGINE
 	help
 	  Find out whether you have a PCI motherboard. PCI is the name of a
 	  bus system, i.e. the way the CPU talks to the other stuff inside
@@ -1175,6 +1175,12 @@ config PCI_DOMAINS
 	bool
 	depends on PCI
 
+config PCI_NANOENGINE
+	bool "BSE nanoEngine PCI support"
+	depends on SA1100_NANOENGINE
+	help
+	  Enable PCI on the BSE nanoEngine board.
+
 config PCI_SYSCALL
 	def_bool PCI
 

arch/arm/mach-sa1100/Kconfig

@@ -121,6 +121,8 @@ config SA1100_LART
 config SA1100_NANOENGINE
 	bool "nanoEngine"
 	select CPU_FREQ_SA1110
+	select PCI
+	select PCI_NANOENGINE
 	help
 	  Say Y here if you are using the Bright Star Engineering nanoEngine.
 	  See <http://www.brightstareng.com/arm/nanoeng.htm> for information

arch/arm/mach-sa1100/Makefile

@@ -38,6 +38,7 @@ obj-$(CONFIG_SA1100_LART)		+= lart.o
 led-$(CONFIG_SA1100_LART)		+= leds-lart.o
 
 obj-$(CONFIG_SA1100_NANOENGINE)		+= nanoengine.o
+obj-$(CONFIG_PCI_NANOENGINE)		+= pci-nanoengine.o
 
 obj-$(CONFIG_SA1100_PLEB)		+= pleb.o
 

arch/arm/mach-sa1100/include/mach/hardware.h

@@ -76,4 +76,12 @@ static inline unsigned long get_clock_tick_rate(void)
 #include "SA-1101.h"
 #endif
 
+#if defined(CONFIG_ARCH_SA1100) && defined(CONFIG_PCI)
+#define PCIBIOS_MIN_IO		0
+#define PCIBIOS_MIN_MEM		0
+#define pcibios_assign_all_busses()	1
+#define HAVE_ARCH_PCI_SET_DMA_MASK	1
+#endif
+
+
 #endif  /* _ASM_ARCH_HARDWARE_H */

arch/arm/mach-sa1100/include/mach/nanoengine.h

@@ -14,6 +14,8 @@
 #ifndef __ASM_ARCH_NANOENGINE_H
 #define __ASM_ARCH_NANOENGINE_H
 
+#include <mach/irqs.h>
+
 #define GPIO_PC_READY0	GPIO_GPIO(11) /* ready for socket 0 (active high)*/
 #define GPIO_PC_READY1	GPIO_GPIO(12) /* ready for socket 1 (active high) */
 #define GPIO_PC_CD0	GPIO_GPIO(13) /* detect for socket 0 (active low) */
@@ -21,10 +23,30 @@
 #define GPIO_PC_RESET0	GPIO_GPIO(15) /* reset socket 0 */
 #define GPIO_PC_RESET1	GPIO_GPIO(16) /* reset socket 1 */
 
+#define NANOENGINE_IRQ_GPIO_PCI		IRQ_GPIO0
 #define NANOENGINE_IRQ_GPIO_PC_READY0	IRQ_GPIO11
 #define NANOENGINE_IRQ_GPIO_PC_READY1	IRQ_GPIO12
 #define NANOENGINE_IRQ_GPIO_PC_CD0	IRQ_GPIO13
 #define NANOENGINE_IRQ_GPIO_PC_CD1	IRQ_GPIO14
 
+/*
+ * nanoEngine Memory Map:
+ *
+ * 0000.0000 - 003F.0000 -   4 MB Flash
+ * C000.0000 - C1FF.FFFF -  32 MB SDRAM
+ * 1860.0000 - 186F.FFFF -   1 MB Internal PCI Memory Read/Write
+ * 18A1.0000 - 18A1.FFFF -  64 KB Internal PCI Config Space
+ * 4000.0000 - 47FF.FFFF - 128 MB External Bus I/O - Multiplexed Mode
+ * 4800.0000 - 4FFF.FFFF - 128 MB External Bus I/O - Non-Multiplexed Mode
+ *
+ */
+
+#define NANO_PCI_MEM_RW_PHYS		0x18600000
+#define NANO_PCI_MEM_RW_VIRT		0xf1000000
+#define NANO_PCI_MEM_RW_SIZE		SZ_1M
+#define NANO_PCI_CONFIG_SPACE_PHYS	0x18A10000
+#define NANO_PCI_CONFIG_SPACE_VIRT	0xf2000000
+#define NANO_PCI_CONFIG_SPACE_SIZE	SZ_64K
+
 #endif
 

arch/arm/mach-sa1100/nanoengine.c

@@ -26,6 +26,7 @@
 #include <asm/mach/serial_sa1100.h>
 
 #include <mach/hardware.h>
+#include <mach/nanoengine.h>
 
 #include "generic.h"
 
@@ -74,11 +75,17 @@ static struct map_desc nanoengine_io_desc[] __initdata = {
 		.pfn		= __phys_to_pfn(0x10000000),
 		.length		= 0x00100000,
 		.type		= MT_DEVICE
+	}, {
+		/* Internal PCI Memory Read/Write */
+		.virtual	= NANO_PCI_MEM_RW_VIRT,
+		.pfn		= __phys_to_pfn(NANO_PCI_MEM_RW_PHYS),
+		.length		= NANO_PCI_MEM_RW_SIZE,
+		.type		= MT_DEVICE
 	}, {
 		/* Internal PCI Config Space */
-		.virtual	= 0xf1000000,
-		.pfn		= __phys_to_pfn(0x18A00000),
-		.length		= 0x00100000,
+		.virtual	= NANO_PCI_CONFIG_SPACE_VIRT,
+		.pfn		= __phys_to_pfn(NANO_PCI_CONFIG_SPACE_PHYS),
+		.length		= NANO_PCI_CONFIG_SPACE_SIZE,
 		.type		= MT_DEVICE
 	}
 };

arch/arm/mach-sa1100/pci-nanoengine.c

+/*
+ * linux/arch/arm/mach-sa1100/pci-nanoengine.c
+ *
+ * PCI functions for BSE nanoEngine PCI
+ *
+ * Copyright (C) 2010 Marcelo Roberto Jimenez <mroberto@cpti.cetuc.puc-rio.br>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ */
+#include <linux/kernel.h>
+#include <linux/irq.h>
+#include <linux/pci.h>
+#include <linux/spinlock.h>
+
+#include <asm/mach/pci.h>
+#include <asm/mach-types.h>
+
+#include <mach/nanoengine.h>
+
+static DEFINE_SPINLOCK(nano_lock);
+
+static int nanoengine_get_pci_address(struct pci_bus *bus,
+	unsigned int devfn, int where, unsigned long *address)
+{
+	int ret = PCIBIOS_DEVICE_NOT_FOUND;
+	unsigned int busnr = bus->number;
+
+	*address = NANO_PCI_CONFIG_SPACE_VIRT +
+		((bus->number << 16) | (devfn << 8) | (where & ~3));
+
+	ret = (busnr > 255 || devfn > 255 || where > 255) ?
+		PCIBIOS_DEVICE_NOT_FOUND : PCIBIOS_SUCCESSFUL;
+
+	return ret;
+}
+
+static int nanoengine_read_config(struct pci_bus *bus, unsigned int devfn, int where,
+	int size, u32 *val)
+{
+	int ret;
+	unsigned long address;
+	unsigned long flags;
+	u32 v;
+
+	/* nanoEngine PCI bridge does not return -1 for a non-existing
+	 * device. We must fake the answer. We know that the only valid
+	 * device is device zero at bus 0, which is the network chip. */
+	if (bus->number != 0 || (devfn >> 3) != 0) {
+		v = -1;
+		nanoengine_get_pci_address(bus, devfn, where, &address);
+		goto exit_function;
+	}
+
+	spin_lock_irqsave(&nano_lock, flags);
+
+	ret = nanoengine_get_pci_address(bus, devfn, where, &address);
+	if (ret != PCIBIOS_SUCCESSFUL)
+		return ret;
+	v = __raw_readl(address);
+
+	spin_unlock_irqrestore(&nano_lock, flags);
+
+	v >>= ((where & 3) * 8);
+	v &= (unsigned long)(-1) >> ((4 - size) * 8);
+
+exit_function:
+	*val = v;
+	return PCIBIOS_SUCCESSFUL;
+}
+
+static int nanoengine_write_config(struct pci_bus *bus, unsigned int devfn, int where,
+	int size, u32 val)
+{
+	int ret;
+	unsigned long address;
+	unsigned long flags;
+	unsigned shift;
+	u32 v;
+
+	shift = (where & 3) * 8;
+
+	spin_lock_irqsave(&nano_lock, flags);
+
+	ret = nanoengine_get_pci_address(bus, devfn, where, &address);
+	if (ret != PCIBIOS_SUCCESSFUL)
+		return ret;
+	v = __raw_readl(address);
+	switch (size) {
+	case 1:
+		v &= ~(0xFF << shift);
+		v |= val << shift;
+		break;
+	case 2:
+		v &= ~(0xFFFF << shift);
+		v |= val << shift;
+		break;
+	case 4:
+		v = val;
+		break;
+	}
+	__raw_writel(v, address);
+
+	spin_unlock_irqrestore(&nano_lock, flags);
+
+	return PCIBIOS_SUCCESSFUL;
+}
+
+static struct pci_ops pci_nano_ops = {
+	.read	= nanoengine_read_config,
+	.write	= nanoengine_write_config,
+};
+
+static int __init pci_nanoengine_map_irq(struct pci_dev *dev, u8 slot, u8 pin)
+{
+	return NANOENGINE_IRQ_GPIO_PCI;
+}
+
+struct pci_bus * __init pci_nanoengine_scan_bus(int nr, struct pci_sys_data *sys)
+{
+	return pci_scan_bus(sys->busnr, &pci_nano_ops, sys);
+}
+
+static struct resource pci_io_ports = {
+	.name	= "PCI IO",
+	.start	= 0x400,
+	.end	= 0x7FF,
+	.flags	= IORESOURCE_IO,
+};
+
+static struct resource pci_non_prefetchable_memory = {
+	.name	= "PCI non-prefetchable",
+	.start	= NANO_PCI_MEM_RW_PHYS,
+	/* nanoEngine documentation says there is a 1 Megabyte window here,
+	 * but PCI reports just 128 + 8 kbytes. */
+	.end	= NANO_PCI_MEM_RW_PHYS + NANO_PCI_MEM_RW_SIZE - 1,
+/*	.end	= NANO_PCI_MEM_RW_PHYS + SZ_128K + SZ_8K - 1,*/
+	.flags	= IORESOURCE_MEM,
+};
+
+/*
+ * nanoEngine PCI reports 1 Megabyte of prefetchable memory, but it
+ * overlaps with previously defined memory.
+ *
+ * Here is what happens:
+ *
+# dmesg
+...
+pci 0000:00:00.0: [8086:1209] type 0 class 0x000200
+pci 0000:00:00.0: reg 10: [mem 0x00021000-0x00021fff]
+pci 0000:00:00.0: reg 14: [io  0x0000-0x003f]
+pci 0000:00:00.0: reg 18: [mem 0x00000000-0x0001ffff]
+pci 0000:00:00.0: reg 30: [mem 0x00000000-0x000fffff pref]
+pci 0000:00:00.0: supports D1 D2
+pci 0000:00:00.0: PME# supported from D0 D1 D2 D3hot
+pci 0000:00:00.0: PME# disabled
+PCI: bus0: Fast back to back transfers enabled
+pci 0000:00:00.0: BAR 6: can't assign mem pref (size 0x100000)
+pci 0000:00:00.0: BAR 2: assigned [mem 0x18600000-0x1861ffff]
+pci 0000:00:00.0: BAR 2: set to [mem 0x18600000-0x1861ffff] (PCI address [0x0-0x1ffff])
+pci 0000:00:00.0: BAR 0: assigned [mem 0x18620000-0x18620fff]
+pci 0000:00:00.0: BAR 0: set to [mem 0x18620000-0x18620fff] (PCI address [0x20000-0x20fff])
+pci 0000:00:00.0: BAR 1: assigned [io  0x0400-0x043f]
+pci 0000:00:00.0: BAR 1: set to [io  0x0400-0x043f] (PCI address [0x0-0x3f])
+ *
+ * On the other hand, if we do not request the prefetchable memory resource,
+ * linux will alloc it first and the two non-prefetchable memory areas that
+ * are our real interest will not be mapped. So we choose to map it to an
+ * unused area. It gets recognized as expansion ROM, but becomes disabled.
+ *
+ * Here is what happens then:
+ *
+# dmesg
+...
+pci 0000:00:00.0: [8086:1209] type 0 class 0x000200
+pci 0000:00:00.0: reg 10: [mem 0x00021000-0x00021fff]
+pci 0000:00:00.0: reg 14: [io  0x0000-0x003f]
+pci 0000:00:00.0: reg 18: [mem 0x00000000-0x0001ffff]
+pci 0000:00:00.0: reg 30: [mem 0x00000000-0x000fffff pref]
+pci 0000:00:00.0: supports D1 D2
+pci 0000:00:00.0: PME# supported from D0 D1 D2 D3hot
+pci 0000:00:00.0: PME# disabled
+PCI: bus0: Fast back to back transfers enabled
+pci 0000:00:00.0: BAR 6: assigned [mem 0x78000000-0x780fffff pref]
+pci 0000:00:00.0: BAR 2: assigned [mem 0x18600000-0x1861ffff]
+pci 0000:00:00.0: BAR 2: set to [mem 0x18600000-0x1861ffff] (PCI address [0x0-0x1ffff])
+pci 0000:00:00.0: BAR 0: assigned [mem 0x18620000-0x18620fff]
+pci 0000:00:00.0: BAR 0: set to [mem 0x18620000-0x18620fff] (PCI address [0x20000-0x20fff])
+pci 0000:00:00.0: BAR 1: assigned [io  0x0400-0x043f]
+pci 0000:00:00.0: BAR 1: set to [io  0x0400-0x043f] (PCI address [0x0-0x3f])
+
+# lspci -vv -s 0000:00:00.0
+00:00.0 Class 0200: Device 8086:1209 (rev 09)
+        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
+        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR+ <PERR+ INTx-
+        Latency: 0 (2000ns min, 14000ns max), Cache Line Size: 32 bytes
+        Interrupt: pin A routed to IRQ 0
+        Region 0: Memory at 18620000 (32-bit, non-prefetchable) [size=4K]
+        Region 1: I/O ports at 0400 [size=64]
+        Region 2: [virtual] Memory at 18600000 (32-bit, non-prefetchable) [size=128K]
+        [virtual] Expansion ROM at 78000000 [disabled] [size=1M]
+        Capabilities: [dc] Power Management version 2
+                Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
+                Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=2 PME-
+        Kernel driver in use: e100
+        Kernel modules: e100
+ *
+ */
+static struct resource pci_prefetchable_memory = {
+	.name	= "PCI prefetchable",
+	.start	= 0x78000000,
+	.end	= 0x78000000 + NANO_PCI_MEM_RW_SIZE - 1,
+	.flags	= IORESOURCE_MEM  | IORESOURCE_PREFETCH,
+};
+
+static int __init pci_nanoengine_setup_resources(struct resource **resource)
+{
+	if (request_resource(&ioport_resource, &pci_io_ports)) {
+		printk(KERN_ERR "PCI: unable to allocate io port region\n");
+		return -EBUSY;
+	}
+	if (request_resource(&iomem_resource, &pci_non_prefetchable_memory)) {
+		release_resource(&pci_io_ports);
+		printk(KERN_ERR "PCI: unable to allocate non prefetchable\n");
+		return -EBUSY;
+	}
+	if (request_resource(&iomem_resource, &pci_prefetchable_memory)) {
+		release_resource(&pci_io_ports);
+		release_resource(&pci_non_prefetchable_memory);
+		printk(KERN_ERR "PCI: unable to allocate prefetchable\n");
+		return -EBUSY;
+	}
+	resource[0] = &pci_io_ports;
+	resource[1] = &pci_non_prefetchable_memory;
+	resource[2] = &pci_prefetchable_memory;
+
+	return 1;
+}
+
+int __init pci_nanoengine_setup(int nr, struct pci_sys_data *sys)
+{
+	int ret = 0;
+
+	if (nr == 0) {
+		sys->mem_offset = NANO_PCI_MEM_RW_PHYS;
+		sys->io_offset = 0x400;
+		ret = pci_nanoengine_setup_resources(sys->resource);
+		/* Enable alternate memory bus master mode, see
+		 * "Intel StrongARM SA1110 Developer's Manual",
+		 * section 10.8, "Alternate Memory Bus Master Mode". */
+		GPDR = (GPDR & ~GPIO_MBREQ) | GPIO_MBGNT;
+		GAFR |= GPIO_MBGNT | GPIO_MBREQ;
+		TUCR |= TUCR_MBGPIO;
+	}
+
+	return ret;
+}
+
+static struct hw_pci nanoengine_pci __initdata = {
+	.map_irq		= pci_nanoengine_map_irq,
+	.nr_controllers		= 1,
+	.scan			= pci_nanoengine_scan_bus,
+	.setup			= pci_nanoengine_setup,
+};
+
+static int __init nanoengine_pci_init(void)
+{
+	if (machine_is_nanoengine())
+		pci_common_init(&nanoengine_pci);
+	return 0;
+}
+
+subsys_initcall(nanoengine_pci_init);