Commit b557471b authored by Bhupesh Sharma's avatar Bhupesh Sharma Committed by Bjorn Andersson

arm64: dts: qcom: pmm8155au_2: Add base dts file

Add base DTS file for pmm8155au_2 along with GPIOs, power-on, rtc and vadc
nodes.

Cc: Mark Brown <broonie@kernel.org>
Cc: Vinod Koul <vkoul@kernel.org>
Reviewed-by: default avatarBjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: default avatarBhupesh Sharma <bhupesh.sharma@linaro.org>
Link: https://lore.kernel.org/r/20210617054548.353293-5-bhupesh.sharma@linaro.org
[bjorn: Added gpio-ranges to pmm8155au_2_gpios]
Signed-off-by: default avatarBjorn Andersson <bjorn.andersson@linaro.org>
parent 10489ef1
// SPDX-License-Identifier: BSD-3-Clause
/*
* Copyright (c) 2021, Linaro Limited
*/
#include <dt-bindings/input/input.h>
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/spmi/spmi.h>
/ {
thermal-zones {
pmm8155au-2-thermal {
polling-delay-passive = <100>;
polling-delay = <0>;
thermal-sensors = <&pmm8155au_2_temp>;
trips {
trip0 {
temperature = <95000>;
hysteresis = <0>;
type = "passive";
};
trip1 {
temperature = <115000>;
hysteresis = <0>;
type = "hot";
};
trip2 {
temperature = <145000>;
hysteresis = <0>;
type = "critical";
};
};
};
};
};
&spmi_bus {
pmic@4 {
compatible = "qcom,pmm8155au", "qcom,spmi-pmic";
reg = <0x4 SPMI_USID>;
#address-cells = <1>;
#size-cells = <0>;
power-on@800 {
compatible = "qcom,pm8916-pon";
reg = <0x0800>;
status = "disabled";
};
pmm8155au_2_temp: temp-alarm@2400 {
compatible = "qcom,spmi-temp-alarm";
reg = <0x2400>;
interrupts = <0x4 0x24 0x0 IRQ_TYPE_EDGE_BOTH>;
io-channels = <&pmm8155au_2_adc ADC5_DIE_TEMP>;
io-channel-names = "thermal";
#thermal-sensor-cells = <0>;
};
pmm8155au_2_adc: adc@3100 {
compatible = "qcom,spmi-adc5";
reg = <0x3100>;
#address-cells = <1>;
#size-cells = <0>;
#io-channel-cells = <1>;
interrupts = <0x4 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
ref-gnd@0 {
reg = <ADC5_REF_GND>;
qcom,pre-scaling = <1 1>;
label = "ref_gnd";
};
vref-1p25@1 {
reg = <ADC5_1P25VREF>;
qcom,pre-scaling = <1 1>;
label = "vref_1p25";
};
die-temp@6 {
reg = <ADC5_DIE_TEMP>;
qcom,pre-scaling = <1 1>;
label = "die_temp";
};
};
pmm8155au_2_gpios: gpio@c000 {
compatible = "qcom,pmm8155au-gpio";
reg = <0xc000>;
gpio-controller;
#gpio-cells = <2>;
gpio-ranges = <&pmm8155au_2_gpios 0 0 10>;
interrupt-controller;
#interrupt-cells = <2>;
};
};
pmic@5 {
compatible = "qcom,pmm8155au", "qcom,spmi-pmic";
reg = <0x5 SPMI_USID>;
#address-cells = <1>;
#size-cells = <0>;
};
};
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment